The Impact of Oxygen Content in O-Doped MoS2 on the Kinetics of Polysulfide Conversion in Li-S Batteries.

Polysulfide shuttle and sluggish sulfur redox kinetics remain key challenges in lithium-sulfur batteries. Previous researches have shown that introducing oxygen into transition metal sulfides helps to capture polysulfides and enhance their conversion kinetics. Based on this, further investigations are conducted to explore the impact of oxygen doping levels on the physical-chemical properties and electrocatalytic performance of MoS2. The findings reveal that MoS2 doped with high-content oxygen exhibits enhanced conductivity and polysulfides conversion kinetics compared to MoS2 with low-content oxygen doping, which can be attributed to the alteration of crystal structure from 2H-phase to the 1T-phase, the introduction of increased Li-O interactions, and the effect of defects resulting from high-oxygen doping. Consequently, the lithium-sulfur batteries using high-oxygen doped MoS2 as a catalyst deliver a high discharge capacity of 1015 mAh g-1 at 0.25C and maintain 78.5% capacity after 300 more cycles. Specifically, lithium-sulfur batteries employing paper-based electrodedemonstrate an areal capacity of 3.91 mAh cm-2 at 0.15C, even with sulfur loading of 4.1 mg cm-2 and electrolyte of 6.7 µL mg-1. These results indicate that oxygen doping levels can modify the properties of MoS2, and high-oxygen doped MoS2 shows promise as an efficient catalyst for lithium-sulfur batteries.

Block Copolymer Nanoparticles Remove Biofilms of Drug-Resistant Gram-Positive Bacteria by Nanoscale Bacterial Debridement.

Biofilms and the rapid evolution of multidrug resistance complicate the treatment of bacterial infections. Antibiofilm agents such as metallic-inorganic nanoparticles or peptides act by exerting antibacterial effects and, hence, do not combat biofilms of antibiotics-resistant strains. In this Letter, we show that the block copolymer DA95B5, dextran- block-poly((3-acrylamidopropyl) trimethylammonium chloride (AMPTMA)- co-butyl methacrylate (BMA)), effectively removes preformed biofilms of various clinically relevant multidrug-resistant Gram-positive bacteria including methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Enterococci (VRE V583), and Enteroccocus faecalis (OG1RF). DA95B5 self-assembles into core-shell nanoparticles with a nonfouling dextran shell and a cationic core. These nanoparticles diffuse into biofilms and attach to bacteria but do not kill them; instead, they promote the gradual dispersal of biofilm bacteria, probably because the solubility of the bacteria-nanoparticle complex is enhanced by the nanoparticle dextran shell. DA95B5, when applied as a solution to a hydrogel pad dressing, shows excellent in vivo MRSA biofilm removal efficacy of 3.6 log reduction in a murine excisional wound model, which is significantly superior to that for vancomycin. Furthermore, DA95B5 has very low in vitro hemolysis and negligible in vivo acute toxicity. This new strategy for biofilm removal (nanoscale bacterial debridement) is orthogonal to conventional rapidly developing resistance traits in bacteria so that it is as effective toward resistant strains as it is toward sensitive strains and may have widespread applications.

Synthesis, Structure, and Anion Binding Properties of Electron-Deficient Tetrahomocorona[4]arenes: Shape Selectivity in Anion-π Interactions.

Tetrahomocorona[2]arene[2]tetrazines were constructed by means of a fragment coupling strategy based on nucleophilic aromatic substitution reaction starting from 3,6-dichlorotetrazine and o-, m-, and p-bis(hydroxymethyl)benzenes. The unprecedented macrocycles gave rectangular box-like cavities with tunable cavity sizes and deficient electronic properties depending on the substitution pattern of phenylene. Due to anion-π interactions, they formed complexes selectively with azide and thiocyanate owing to complementary shapes between host and guest.

A CO2-switchable amidine monomer: synthesis and characterization.

Smart system employed CO2 gas as new trigger has been attracting enormous attention in recent years, but few monomers that are capable of switching their hydrophobicity/hydrophility upon CO2 stimulation have been reported. A novel CO2 responsive monomer, 4-vinylbenzyl amidine, is designed and synthesized in this work with N,N-dimethylacetamide dimethyl acetal and 4-vinylbenzyl amine that is prepared through the Gabriel reaction. In bi-phase solvent of n-hexane and water, the monomer dissolves in n-hexane first and then transforms into water upon the CO2 treatment, indicating a hydrophobic to hydrophilic transition. This transformation is demonstrated as reversible by monitoring the conductivity variation of its wet dimethyl formamide solution during alternate bubbling/removing CO2. The protonation of 4-vinylbenzyl amidine upon CO2 treatment is demonstrated by 1H NMR which also accounts for the dissolubility change. The reversible addition-fragmentation chain-transfer polymerization of this monomer is also performed, finding the reaction only occurs in glacial acetic acid. The reason can be ascribed to the different radical structure produced in different solvent.

CO2-Induced Reversible Dispersion of Graphene by a Melamine Derivative.

Smart graphene with stimuli-responsive dispersity has great potential for applications in medical and biochemical fields. Nevertheless, reversible dispersion/aggregation of graphene in water with biocompatible and removable trigger still represents a crucial challenge. Here, we report CO2-induced reversible graphene dispersion by noncovalent functionalization of reduced graphene oxide with N(2),N(4),N(6)-tris(3-(dimethylamino)propyl)-1,3,5-triazine-2,4,6-triamine (MET). It was demonstrated that MET can be strongly adsorbed on graphene surface through van der Waals interaction to facilitate dispersing graphene in water. Moreover, reversible aggregation/dispersion of graphene can be achieved simply by alternately bubbling CO2 and N2 to control the desorption/adsorption of MET on graphene surface.

Solvent-Driven Formation of Worm-Like Micelles Assembled from a CO2-Responsive Triblock Copolymer.

Polymer worm-like micelles (WLMs) are difficult to target due to the narrow composition window. In this work, we report polymer WLMs self-assembled from a linear ABC triblock copolymer consisting of an intermediate fluorinated block of poly(2,2,3,4,4,4-hexafluorobutyl methacrylate) (F), a hydrophilic segment of poly(ethylene oxide) (O) and a CO2-responsive flank of poly(2-(diethylamino)ethyl methacrylate) (E). In the mixed solvent of water and ethanol, the polymer aggregates evolve from spheres to short rods, then long cylinders and finally WLMs when the volume ratio of water increases from 0 to 50%. Upon the stimulus of CO2, the E block is protonated, thus transforms from hydrophobic to hydrophilic. However, the WLMs just partially return back to spheres even the protonation degree of E block is up to 95%. The closely packed arrangement of fluorinated block caused by the increasing interfacial tension of the fluorinated blocks and solvent could account for the formation of WLMs and its shape alternation under CO2 stimulus.

Insights into the relationship between CO2 switchability and basicity: examples of melamine and its derivatives.

Owing to its wide availability, nontoxicity, and low cost, CO2 working as a trigger to reversibly switch material properties, including polarity, ionic strength, hydrophilicity, viscosity, surface charge, and degree of polymerization or cross-linking, has attracted an increasing attention in recent years. However, a quantitative correlation between basicity of these materials and their CO2 switchability has been less documented though it is of great importance for fabricating switchable system. In this work, the "switch-on" and "switch-off" abilities of melamine and its amino-substituted derivatives by introducing and removing CO2 are studied, and then their quantitative relationship with basicity is established, so that performances of other organobases can be quantitatively predicted. These findings are beneficial for forecasting the CO2 stimuli-responsive behavior of other organobases and the design of CO2-switchable materials.

CO2-switchable multi-compartment micelles with segregated corona.

CO2-switchable multi-compartment micelles (MCMs) with a segregated corona formed by a purpose-designed ABC triblock copolymer are reported. They can be switched "on" and "off" when sequentially treated with CO2 and N2, due to the protonation-deprotonation of the tertiary amine groups along the polymer skeleton.

Stable Flexible Electronic Devices under Harsh Conditions Enabled by Double-Network Hydrogels Containing Binary Cations.

Hydrogels are increasingly used in flexible electronic devices, but the mechanical and electrochemical stabilities of hydrogel devices are often limited under specific harsh conditions. Herein, chemically/physically cross-linked double-network (DN) hydrogels containing binary cations Zn2+ and Li+ are constructed in order to address the above challenges. Double networks of chemically cross-linked polyacrylamide (PAM) and physically cross-linked κ-Carrageenan (κ-CG) are designed to account for the mechanical robustness while binary cations endow the hydrogels with excellent ionic conductivity and outstanding environmental adaptability. Excellent mechanical robustness and ionic conductivity (25 °C, 2.26 S·m-1; -25 °C, 1.54 S·m-1) have been achieved. Utilizing the DN hydrogels containing binary cations as signal-converting materials, we fabricated flexible mechanosensors. High gauge factors (resistive strain sensors, 2.4; capacitive pressure sensors, 0.82 kPa-1) and highly stable sensing ability have been achieved. Interestingly, zinc-ion hybrid supercapacitors containing the DN hydrogels containing binary cations as electrolytes have achieved an initial capacity of 52.5 mAh·g-1 at a current density of 3 A·g-1 and a capacity retention rate of 82.9% after 19,000 cycles. Proper working of the zinc-ion hybrid supercapacitors at subzero conditions and stable charge-discharge for more than 19,000 cycles at -25 °C have been demonstrated. Overall, DN hydrogels containing binary cations have provided promising materials for high-performance flexible electronic devices under harsh conditions.

Highly Stable, Bending-Tolerant, and Sustainable Flexible Heater through a Scalable Papermaking Procedure.

Flexible electrothermal heaters have attracted abundant attention in recent years due to their wide applications, but their preparation with high efficiency remains a challenge. Here in this work, a highly stable and bending-tolerant flexible heater was fabricated with graphite nanosheets and cellulose fibers through a scalable papermaking procedure. Its electrothermal property can be enhanced by a hot-pressing treatment and introduction of cationic polyacrylamide (CPAM) during the papermaking protocol. The flexible heater may quickly reach its maximum temperature of 239.8 °C in around 1 min at a voltage of 9 V. The power density was up to 375.3 °C cm2 w-1. It appeared to have a high tolerance for bending deformation with various curvatures, and the temperature remained stable even under 100 bending with frequency of around 0.17 Hz. Over 100 alternatively heating and cooling cycles, it worked stably as well. It was proved to be used as wearable heating equipment, soft heaters, and aircraft deicing devices, suggesting its great prospect in the field of heat management.

Double layered asymmetrical hydrogels enhanced by thermosensitive microgels for high-performance mechanosensors and actuators.

Thermosensitive hydrogels have found extensive applications in soft devices, but they often suffer from limited functionalities, low response rate and small response amplitude. In this work, double layered asymmetrical hydrogels composed of a thermosensitive layer and a non-thermosensitive layer are developed to simultaneously achieve high-performance mechanosensing and actuating properties in a single hydrogel. In thermosensitive layer, thermosensitive microgels are introduced to construct hierarchical structure, which accounts for the enhanced thermosensitive behaviors by cooperative responsiveness. In non-thermosensitive layer, poly(acrylamide-co-acrylic acid) (P(AM-co-AA)) hydrogel is constructed. KCl is introduced as conductive component. Mechanosensors for monitoring various mechanical stimuli in daily life have been fabricated utilizing such hydrogels and high gauge factors (GF) have been achieved, 0.38 for resistive strain sensors, 9.40 kPa-1 for piezoresistive pressure sensors and 3.92 kPa-1 for capacitive pressure sensors. Because of the asymmetrical structure, such hydrogels also exhibit outstanding actuating properties with a fast response rate of 863°/min and a bending amplitude about 360°. Interestingly, grasping-releasing of target objects utilizing an octopus-shaped hydrogel actuator and temperature alerting based on hydrogel actuator are also demonstrated. Overall, the double layered asymmetrical ionic hydrogels have provided a new clue to construct hydrogel devices with multiple functionalities and enhanced response properties.

Simulating the electrostatic guidance of the vectorial translocations in hexameric helicases and translocases.

The molecular origin of the action of helicases is explored, starting with a model built based on the different X-ray structures of the large tumor antigen (LTag) hexameric helicase and a simplified model containing the ionized phosphate backbones of a single-strand DNA. The coupling between the protein structural changes and the translocation process is quantified using an effective electrostatic free-energy surface for the protein/DNA complex. This surface is then used in Langevin dynamics simulations of the time dependence of the translocation process. Remarkably, the simulated motion along the free-energy surface results in a vectorial translocation of the DNA, consistent with the biological process. The electrostatic energy of the system appears to reproduce the directionality of this process. Thus, we are able to provide a consistent structure-based molecular description of the energetic and dynamics of the translocation process. This analysis may have general implications for relating structural models to translocation directionality in helicases and other DNA translocases.

Electrospun Elastic Films Containing AgNW-Bridged MXene Networks as Capacitive Electronic Skins.

Electronic skins (e-skins) are increasingly investigated and applied in wearable devices, but the robustness and convenient production of traditional e-skins are restricted. In this work, electrospun sandwich-structured elastic films (ESEFs) are developed and utilized as capacitive e-skins. The ESEFs consist of two nanocomposite mats as the electrode layers and a sandwiched thermoplastic polyurethane (TPU) mat as the dielectric layer. The nanocomposite mats are composed of thermoplastic polyurethane (TPU) and AgNW-bridged MXene (AgNW, silver nanowire; MXene, Ti3C2Tx) conductive network. The resulting ESEFs achieve a tensile strength of 14.80 MPa, an elongation at break of 270%, and an outstanding antifatigue property. E-skins of such ESEFs have the ability to respond to both strain and pressure with a high gauge factor (GF) (strain: GF = 1.21; pressure: GF = 0.029 kPa-1), wide response range (strain: 0-150%; pressure: 0-70 kPa), low response time, and outstanding stability (2000 cycles). On the basis of integrated sensing performances, such e-skins are further applied in monitoring various mechanical stimuli in daily life, including bending of a plastic plate, joint bending, and swallowing.

Mussel-inspired self-adhesive hydrogels by conducting free radical polymerization in both aqueous phase and micelle phase and their applications in flexible sensors.

Polydopamine (PDA)-based self-adhesive hydrogel sensors are extensively explored but it is still a challenge to construct PDA-based hydrogels by free radical polymerization. Herein, a new approach to construct self-adhesive hydrogels by conducting free radical polymerization in both aqueous phase and micelle phase is developed. The following two-phase polymerization processes account for the formation of the self-adhesive hydrogels. The first one is the polymerization of acrylamide (AM) and dopamine (DA) in aqueous phase to form adhesive component PAM-PDA (PAM, polyacrylamide; PDA, polydopamine). The second one is the polymerization of hydrophobic monomer 2-methoxyethyl acrylate (MEA) in micelles of an amphiphilic block copolymer Pluronic F127 diacrylate (F127DA). The poly(2-methoxyethyl acrylate) (PMEA) networks help to maintain the high robustness of the hydrogel. Because PMEA and PDA form in relatively separated phases, the inhibition effect of PDA on the free radical polymerization process of PMEA is weakened. Based on this mechanism, mechanically strong and adhesive hydrogels are achieved. The introduced ions during preparation process, such as Na+, OH- and K+, endow the resulting hydrogels ionic conductivity. Resistive strain sensor of the hydrogel achieves a high gauge factor (GF) of 5.26, a response time of 0.25 s and high sensing stability. Because of the adhesiveness, such hydrogel sensor can be applied as wearable sensors in monitoring various human motions. To further address the freezing and drying problems of the hydrogels, organohydrogels are constructed in glycerol-water mixed solvent. The organohydrogels exhibit outstanding anti-freezing property and moisture retention ability, and their adhesiveness is well maintained in subzero conditions. Capacitive pressure sensors of the organohydrogels possessing a GF of 2.05 kPa-1, high sensing stability and reversibility, are demonstrated and explored in monitoring diverse human motions.

High-Density Oxygen Doping of Conductive Metal Sulfides for Better Polysulfide Trapping and Li2 S-S8 Redox Kinetics in High Areal Capacity Lithium-Sulfur Batteries.

Exploring new materials and methods to achieve high utilization of sulfur with lean electrolyte is still a common concern in lithium-sulfur batteries. Here, high-density oxygen doping chemistry is introduced for making highly conducting, chemically stable sulfides with a much higher affinity to lithium polysulfides. It is found that doping large amounts of oxygen into NiCo2 S4 is feasible and can make it outperform the pristine oxides and natively oxidized sulfides. Taking the advantages of high conductivity, chemical stability, the introduced large Li-O interactions, and activated Co (Ni) facets for catalyzing Sn 2- , the NiCo2 (O-S)4 is able to accelerate the Li2 S-S8 redox kinetics. Specifically, lithium-sulfur batteries using free-standing NiCo2 (O-S)4 paper and interlayer exhibit the highest capacity of 8.68 mAh cm-2 at 1.0 mA cm-2 even with a sulfur loading of 8.75 mg cm-2 and lean electrolyte of 3.8 µL g-1 . The high-density oxygen doping chemistry can be also applied to other metal compounds, suggesting a potential way for developing more powerful catalysts towards high performance of Li-S batteries.

Xiaoyao Pill Improves the Affective Dysregulation of Sleep-deprived Female Mice by Inhibiting Brain Injury and Regulating the Content of Monoamine Neurotransmitter.

BACKGROUND: Sleep curtailment is a serious problem in many societies. Clinical evidence has shown that sleep deprivation is associated with mood dysregulation, formation of false memory, cardio-metabolic risk factors and outcomes, inflammatory disease risk, and all-cause mortality. The affective disorder dysregulation caused by insufficient sleep has become an increasingly serious health problem. However, to date, not much attention has been paid to the mild affective dysregulation caused by insufficient sleep, and there is no clear and standard therapeutic method to treat it. The Xiaoyao Pill is a classic Chinese medicinal formula, with the effect of dispersing stagnated hepatoqi, invigorating the spleen, and nourishing the blood. Therefore, it is most commonly used to treat gynecological diseases in China. In the present study, the effects of the Xiaoyao Pill on affective dysregulation of sleep-deprived mice and its underlying molecular mechanisms were investigated. METHODS: Forty adult female mice were used in the present study. The sleep deprivation model was established by improving the multi-platform water environment method. After 7 consecutive days of sleep deprivation, the mice were administrated low (LXYP, 0.32mg/kg) and high (HXYP, 0.64 mg/kg) doses of the Xiaoyao Pill for two weeks. Then, the body weight, behavioral deficits, and histopathology were evaluated. Meanwhile, the expression of c-fos protein and the concentrations of monoamine neurotransmitters in the hippocampus and prefrontal cortex were determined after two weeks of treatment. RESULTS: Xiaoyao Pill treatment significantly increased body weight and sucrose consumption and decreased the irritability scores of the sleep-deprived mice. Meanwhile, Xiaoyao Pill treatment prevented brain injury and inhibited the expression of c-fos protein in the hippocampus and prefrontal cortex. In addition, HXYP treatment significantly upregulated the levels of NE in the hippocampus and prefrontal cortex (p < 0.01). LXYP treatment significantly up-regulated the levels of 5-HT in the prefrontal cortex. Meanwhile, both HXYP and LXYP treatment significantly upregulated the levels of DA in the prefrontal cortex (p < 0.05 or p < 0.01) of sleep-deprived mice. CONCLUSION: The present study demonstrates that Xiaoyao Pill treatment prevented the behavioral deficits of mice induced by sleep deprivation by promoting the recovery of brain tissue injury and up-regulating the levels of NE, 5-HT, and DA in the brain tissue.

Transition of cellulose crystalline structure and surface morphology of biomass as a function of ionic liquid pretreatment and its relation to enzymatic hydrolysis.

Cellulose is inherently resistant to breakdown, and the native crystalline structure (cellulose I) of cellulose is considered to be one of the major factors limiting its potential in terms of cost-competitive lignocellulosic biofuel production. Here we report the impact of ionic liquid pretreatment on the cellulose crystalline structure in different feedstocks, including microcrystalline cellulose (Avicel), switchgrass (Panicum virgatum), pine ( Pinus radiata ), and eucalyptus ( Eucalyptus globulus ), and its influence on cellulose hydrolysis kinetics of the resultant biomass. These feedstocks were pretreated using 1-ethyl-3-methyl imidazolium acetate ([C2mim][OAc]) at 120 and 160 °C for 1, 3, 6, and 12 h. The influence of the pretreatment conditions on the cellulose crystalline structure was analyzed by X-ray diffraction (XRD). On a larger length scale, the impact of ionic liquid pretreatment on the surface roughness of the biomass was determined by small-angle neutron scattering (SANS). Pretreatment resulted in a loss of native cellulose crystalline structure. However, the transformation processes were distinctly different for Avicel and for the biomass samples. For Avicel, a transformation to cellulose II occurred for all processing conditions. For the biomass samples, the data suggest that pretreatment for most conditions resulted in an expanded cellulose I lattice. For switchgrass, first evidence of cellulose II only occurred after 12 h of pretreatment at 120 °C. For eucalyptus, first evidence of cellulose II required more intense pretreatment (3 h at 160 °C). For pine, no clear evidence of cellulose II content was detected for the most intense pretreatment conditions of this study (12 h at 160 °C). Interestingly, the rate of enzymatic hydrolysis of Avicel was slightly lower for pretreatment at 160 °C compared with pretreatment at 120 °C. For the biomass samples, the hydrolysis rate was much greater for pretreatment at 160 °C compared with pretreatment at 120 °C. The result for Avicel can be explained by more complete conversion to cellulose II upon precipitation after pretreatment at 160 °C. By comparison, the result for the biomass samples suggests that another factor, likely lignin-carbohydrate complexes, also impacts the rate of cellulose hydrolysis in addition to cellulose crystallinity.

Capacitive Pressure Sensors Containing Reliefs on Solution-Processable Hydrogel Electrodes.

Highly sensitive capacitive-type pressure sensor has been achieved by fabricating reliefs on solution-processable hydrogel electrodes. Hybrid PVA/PANI hydrogels (PVA, poly(vinyl alcohol); PANI, polyaniline) with a fully physically cross-linked binary network are selected as the electrodes of the pressure sensors. On the basis of the solution processability, reliefs are fabricated on the surface of PVA/PANI hydrogel electrodes by a template method. The gauge factor (GF) is enhanced by introducing reliefs and regulated by controlling the composition and relief dimension of hydrogel electrodes. The optimized pressure sensor containing reliefs achieves the highest GF of 7.70 kPa-1 and a sensing range of 0-7.4 kPa. Furthermore, the freezing and drying problems of the hydrogel sensors are overcome by introducing a binary solvent of water/glycerol and the pressure sensing ability at -18 °C has been achieved. Finally, monitoring of various pressures in daily life, such as joint bending, blowing, and brush writing, is demonstrated using such pressure sensors.

Fabrication of Raspberry-like Cytochrome C Surface-Imprinted Nanoparticles Based on MOF Composites for High-Performance Protein Separation.

The development of high-performance protein-imprinted materials is vital to meet the requirements of proteomics research but remains a challenge. Herein, a new type of raspberry-like cytochrome C-imprinted nanoparticle was first designed and fabricated via surface imprinting technology combined with a template immobilization strategy. In particular, the state-of-the-art metal-organic framework (MOF)/carbon nanoparticle (CN) composites were selected as protein immobilization carriers for two advantages: (1) the composites reflected the intrinsic characteristics of MOFs including flexible design, facile preparation, and extensive interactions with proteins and (2) the utilization of composites also overcame the issue associated with the severe agglomeration of individual MOFs during the post-use process. Therefore, the as-prepared composites exhibited a regular raspberry-like shape with good dispersion (polydispersity index (PDI) < 0.25), high specific surface area (551.4 m2 g-1), and outstanding cytochrome C immobilization capacity (900 mg g-1). Furthermore, a zwitterionic monomer was chosen to participate in the synthesis of an imprinting layer to reduce the nonspecific binding with proteins. As a result, the unique design presented here in both the protein immobilization carrier and the selected polymer composition endowed the imprinted material (noted as CN@UIO-66@MIPs) with the excellent ability for cytochrome C enrichment with extremely high recognition ability (imprinting factor (IF) = 6.1), rapid adsorption equilibrium time (40 min), and large adsorption capacity (815 mg g-1). Furthermore, encouraged by the experimental results, we successfully used CN@UIO-66@MIPs to specifically capture cytochrome C in mixed protein solutions and biological samples, which proved them to be a potential candidate for protein separation and purification.

Optimization of Supercritical CO2 Extraction of Moringa oleifera Seed Oil Using Response Surface Methodological Approach and Its Antioxidant Activity.

Moringa (Moringa oleifera) seed oil is an edible vegetable oil rich in unsaturated fatty acids. In this study, the supercritical CO2 fluid extraction method was employed to obtain the maximum yield of moringa seed oil. The effects of temperature, time, and pressure, three characteristics of extractions, on the extraction rate of Moringa seed oil were investigated by single factor test and response surface methodological approach. The optimal process conditions of supercritical CO2 fluid extraction of moringa seed oil were determined as extraction temperature of 45°C, extraction time of 2.5 h, extraction pressure of 50 MPa, and CO2 flow rate of 240 L/h, resulting in a maximum yield of 38.54%. Composition analysis shows that the extracted moringa seed oil is rich in unsaturated fatty acids, including oleic acid, octadecanoic acid, palmitic acid, stearic acid, eicosanoic acid, etc. Furthermore, we found that Moringa seed oil exerted potent antioxidant activities on DPPH and hydroxyl radicals, and its efficacy was comparable to commercial peanut oil and tea oil. Overall, this novel extraction method of moringa seed oil may increase its potential value and application in the food and nutraceutical industries.