RESUMEN
Understanding the nanoscopic chemical and structural changes that drive instabilities in emerging energy materials is essential for mitigating device degradation. The power conversion efficiency of halide perovskite photovoltaic devices has reached 25.7 per cent in single-junction and 29.8 per cent in tandem perovskite/silicon cells1,2, yet retaining such performance under continuous operation has remained elusive3. Here we develop a multimodal microscopy toolkit to reveal that in leading formamidinium-rich perovskite absorbers, nanoscale phase impurities, including hexagonal polytype and lead iodide inclusions, are not only traps for photoexcited carriers, which themselves reduce performance4,5, but also, through the same trapping process, are sites at which photochemical degradation of the absorber layer is seeded. We visualize illumination-induced structural changes at phase impurities associated with trap clusters, revealing that even trace amounts of these phases, otherwise undetected with bulk measurements, compromise device longevity. The type and distribution of these unwanted phase inclusions depends on the film composition and processing, with the presence of polytypes being most detrimental for film photo-stability. Importantly, we reveal that both performance losses and intrinsic degradation processes can be mitigated by modulating these defective phase impurities, and demonstrate that this requires careful tuning of local structural and chemical properties. This multimodal workflow to correlate the nanoscopic landscape of beam-sensitive energy materials will be applicable to a wide range of semiconductors for which a local picture of performance and operational stability has yet to be established.
RESUMEN
Halide perovskite materials have promising performance characteristics for low-cost optoelectronic applications. Photovoltaic devices fabricated from perovskite absorbers have reached power conversion efficiencies above 25 per cent in single-junction devices and 28 per cent in tandem devices1,2. This strong performance (albeit below the practical limits of about 30 per cent and 35 per cent, respectively3) is surprising in thin films processed from solution at low-temperature, a method that generally produces abundant crystalline defects4. Although point defects often induce only shallow electronic states in the perovskite bandgap that do not affect performance5, perovskite devices still have many states deep within the bandgap that trap charge carriers and cause them to recombine non-radiatively. These deep trap states thus induce local variations in photoluminescence and limit the device performance6. The origin and distribution of these trap states are unknown, but they have been associated with light-induced halide segregation in mixed-halide perovskite compositions7 and with local strain8, both of which make devices less stable9. Here we use photoemission electron microscopy to image the trap distribution in state-of-the-art halide perovskite films. Instead of a relatively uniform distribution within regions of poor photoluminescence efficiency, we observe discrete, nanoscale trap clusters. By correlating microscopy measurements with scanning electron analytical techniques, we find that these trap clusters appear at the interfaces between crystallographically and compositionally distinct entities. Finally, by generating time-resolved photoemission sequences of the photo-excited carrier trapping process10,11, we reveal a hole-trapping character with the kinetics limited by diffusion of holes to the local trap clusters. Our approach shows that managing structure and composition on the nanoscale will be essential for optimal performance of halide perovskite devices.
RESUMEN
Carbon nanodots (CNDs) are nanosized light-harvesters emerging as next-generation photosensitizers in photocatalytic reactions. Despite their ever-increasing potential applications, the intricacies underlying their photoexcited charge carrier dynamics are yet to be elucidated. In this study, nitrogen-doped graphitic CNDs (NgCNDs) are selectively excited in the presence of methyl viologen (MV2+, redox mediator) and different electron donors (EDs), namely ascorbic acid (AA) and ethylenediaminetetraacetic acid (EDTA). The consequent formation of the methyl viologen radical cation (MVâ¢+) is investigated, and the excited charge carrier dynamics of the photocatalytic system are understood on a 0.1 ps-1 ms time range, providing spectroscopic evidence of oxidative or reductive quenching mechanisms experienced by optically excited NgCNDs (NgCNDs*) depending on the ED implemented. In the presence of AA, NgCNDs* undergo oxidative quenching by MV2+ to form MVâ¢+, which is short-lived due to dehydroascorbic acid, a product of photoinduced hole quenching of oxidized NgCNDs. The EDTA-mediated reductive quenching of NgCNDs* is observed to be at least 2 orders of magnitude slower due to screening by EDTA-MV2+ complexes, but the MVâ¢+ population is stable due to the irreversibly oxidized EDTA preventing a back reaction. In general, our methodology provides a distinct solution with which to study charge transfer dynamics in photocatalytic systems on an extended time range spanning 10 orders of magnitude. This approach generates a mechanistic understanding to select and develop suitable EDs to promote photocatalytic reactions.
RESUMEN
Halide perovskites perform remarkably in optoelectronic devices. However, this exceptional performance is striking given that perovskites exhibit deep charge-carrier traps and spatial compositional and structural heterogeneity, all of which should be detrimental to performance. Here, we resolve this long-standing paradox by providing a global visualization of the nanoscale chemical, structural and optoelectronic landscape in halide perovskite devices, made possible through the development of a new suite of correlative, multimodal microscopy measurements combining quantitative optical spectroscopic techniques and synchrotron nanoprobe measurements. We show that compositional disorder dominates the optoelectronic response over a weaker influence of nanoscale strain variations even of large magnitude. Nanoscale compositional gradients drive carrier funnelling onto local regions associated with low electronic disorder, drawing carrier recombination away from trap clusters associated with electronic disorder and leading to high local photoluminescence quantum efficiency. These measurements reveal a global picture of the competitive nanoscale landscape, which endows enhanced defect tolerance in devices through spatial chemical disorder that outcompetes both electronic and structural disorder.
RESUMEN
With rapidly growing photoconversion efficiencies, hybrid perovskite solar cells have emerged as promising contenders for next generation, low-cost photovoltaic technologies. Yet, the presence of nanoscale defect clusters, that form during the fabrication process, remains critical to overall device operation, including efficiency and long-term stability. To successfully deploy hybrid perovskites, we must understand the nature of the different types of defects, assess their potentially varied roles in device performance, and understand how they respond to passivation strategies. Here, by correlating photoemission and synchrotron-based scanning probe X-ray microscopies, we unveil three different types of defect clusters in state-of-the-art triple cation mixed halide perovskite thin films. Incorporating ultrafast time-resolution into our photoemission measurements, we show that defect clusters originating at grain boundaries are the most detrimental for photocarrier trapping, while lead iodide defect clusters are relatively benign. Hexagonal polytype defect clusters are only mildly detrimental individually, but can have a significant impact overall if abundant in occurrence. We also show that passivating defects with oxygen in the presence of light, a previously used approach to improve efficiency, has a varied impact on the different types of defects. Even with just mild oxygen treatment, the grain boundary defects are completely healed, while the lead iodide defects begin to show signs of chemical alteration. Our findings highlight the need for multi-pronged strategies tailored to selectively address the detrimental impact of the different defect types in hybrid perovskite solar cells.
RESUMEN
Hybrid-perovskite-based optoelectronic devices are demonstrating unprecedented growth in performance, and defect passivation approaches are highly promising routes to further improve properties. Here, the effect of the molecular ion BF4 - , introduced via methylammonium tetrafluoroborate (MABF4 ) in a surface treatment for MAPbI3 perovskite, is reported. Optical spectroscopy characterization shows that the introduction of tetrafluoroborate leads to reduced non-radiative charge-carrier recombination with a reduction in first-order recombination rate from 6.5 × 106 to 2.5 × 105 s-1 in BF4 - -treated samples, and a consequent increase in photoluminescence quantum yield by an order of magnitude (from 0.5 to 10.4%). 19 F, 11 B, and 14 N solid-state NMR is used to elucidate the atomic-level mechanism of the BF4 - additive-induced improvements, revealing that the BF4 - acts as a scavenger of excess MAI by forming MAI-MABF4 cocrystals. This shifts the equilibrium of iodide concentration in the perovskite phase, thereby reducing the concentration of interstitial iodide defects that act as deep traps and non-radiative recombination centers. These collective results allow us to elucidate the microscopic mechanism of action of BF4 - .
RESUMEN
Efforts to stabilize photoactive formamidinium (FA)based halide perovskites for perovskite photovoltaics have focused on the growth of cubic formamidinium lead iodide (α-FAPbI3) phases by empirically alloying with cesium, methylammonium (MA) cations, or both. We show that such stabilized FA-rich perovskites are noncubic and exhibit ~2° octahedral tilting at room temperature. This tilting, resolvable only with the use of local nanostructure characterization techniques, imparts phase stability by frustrating transitions from photoactive to hexagonal phases. Although the bulk phase appears stable when examined macroscopically, heterogeneous cation distributions allow microscopically unstable regions to form; we found that these transitioned to hexagonal polytypes, leading to local trap-assisted performance losses and photoinstabilities. Using surface-bound ethylenediaminetetraacetic acid, we engineered an octahedral tilt into pure α-FAPbI3 thin films without any cation alloying. The templated photoactive FAPbI3 film was extremely stable against thermal, environmental, and light stressors.
RESUMEN
Hybrid organic-inorganic perovskites show remarkable charge transport properties despite their deposition via low-temperature solution phase methods. It has recently been shown that this includes the ballistic transport of charges following photoexcitation, with ballistic transport lengths as large as 150 nm measured in MAPI3 films, which is almost twice the value reported for GaAs. Here we explore the ballistic transport regime in high-performance triple-cation and K-passivated triple-cation perovskite films, using femtosecond transient absorption microscopy, which allows us to image carrier motion with 10 fs temporal resolution and 10 nm spatial precision. We observe ballistic transport lengths of 160 and 220 nm in triple-cation and K-passivated triple-cation perovskite films, respectively. We propose that the ballistic transport is limited by nanoscale trap clusters at grain boundaries and interfaces, which can be passivated via chemical treatments to enhance the ballistic transport length, which implies that further enhancements are possible as passivation methods are improved.
RESUMEN
All-inorganic double perovskites (elpasolites) are a promising potential alternatives to lead halide perovskites in optoelectronic applications. Although halide mixing is a well-established strategy for band gap tuning, little is known about halide mixing and phase segregation phenomena in double perovskites. Here, we synthesize a wide range of single- and mixed-halide Cs2AgBiX6 (X = Cl, Br, and I) double perovskites using mechanosynthesis and probe their atomic-level microstructure using 133Cs solid-state MAS NMR. We show that mixed Cl/Br materials form pure phases for any Cl/Br ratio while Cl/I and Br/I mixing is only possible within a narrow range of halide ratios (<3 mol % I) and leads to a complex mixture of products for higher ratios. We characterize the optical properties of the resulting materials and show that halide mixing does not lead to an appreciable tunability of the PL emission. We find that iodide incorporation is particularly pernicious in that it quenches the PL emission intensity and radiative charge carrier lifetimes for iodide ratios as low as 0.3 mol %. Our study shows that solid-state NMR, in conjunction with optical spectroscopies, provides a comprehensive understanding of the structure-activity relationships, halide mixing, and phase segregation phenomena in Cs2AgBiX6 (X = Cl, Br, and I) double perovskites.
RESUMEN
Optoelectronic devices based on lead halide perovskites are processed in facile ways, yet are remarkably efficient. There are extensive research efforts investigating lead-free perovskite and perovskite-related compounds, yet there are challenges to synthesize these materials in forms that can be directly integrated into thin film devices rather than as bulk powders. Here, we report on the colloidal synthesis and characterization of lead-free, antifluorite Cs2ZrX6 (X = Cl, Br) nanocrystals that are readily processed into thin films. We use transmission electron microscopy and powder X-ray diffraction measurements to determine their size and structural properties, and solid-state nuclear magnetic resonance measurements reveal the presence of oleate ligand, together with a disordered distribution of Cs surface sites. Density functional theory calculations reveal the band structure and fundamental band gaps of 5.06 and 3.91 eV for Cs2ZrCl6 and Cs2ZrBr6, respectively, consistent with experimental values. Finally, we demonstrate that the Cs2ZrCl6 and Cs2ZrBr6 nanocrystal thin films exhibit tunable, broad white photoluminescence with quantum yields of 45% for the latter, with respective peaks in the blue and green spectral regions and mixed systems exhibiting properties between them. Our work represents a critical step toward the application of lead-free Cs2ZrX6 nanocrystal thin films into next-generation light-emitting applications.
RESUMEN
Mixed-halide lead perovskites have attracted significant attention in the field of photovoltaics and other optoelectronic applications due to their promising bandgap tunability and device performance. Here, the changes in photoluminescence and photoconductance of solution-processed triple-cation mixed-halide (Cs0.06 MA0.15 FA0.79 )Pb(Br0.4 I0.6 )3 perovskite films (MA: methylammonium, FA: formamidinium) are studied under solar-equivalent illumination. It is found that the illumination leads to localized surface sites of iodide-rich perovskite intermixed with passivating PbI2 material. Time- and spectrally resolved photoluminescence measurements reveal that photoexcited charges efficiently transfer to the passivated iodide-rich perovskite surface layer, leading to high local carrier densities on these sites. The carriers on this surface layer therefore recombine with a high radiative efficiency, with the photoluminescence quantum efficiency of the film under solar excitation densities increasing from 3% to over 45%. At higher excitation densities, nonradiative Auger recombination starts to dominate due to the extremely high concentration of charges on the surface layer. This work reveals new insight into phase segregation of mixed-halide mixed-cation perovskites, as well as routes to highly luminescent films by controlling charge density and transfer in novel device structures.
RESUMEN
Mixed lead-tin halide perovskites have sufficiently low bandgaps (â¼1.2 eV) to be promising absorbers for perovskite-perovskite tandem solar cells. Previous reports on lead-tin perovskites have typically shown poor optoelectronic properties compared to neat lead counterparts: short photoluminescence lifetimes (<100 ns) and low photoluminescence quantum efficiencies (<1%). Here, we obtain films with carrier lifetimes exceeding 1 µs and, through addition of small quantities of zinc iodide to the precursor solutions, photoluminescence quantum efficiencies under solar illumination intensities of 2.5%. The zinc additives also substantially enhance the film stability in air, and we use cross-sectional chemical mapping to show that this enhanced stability is because of a reduction in tin-rich clusters. By fabricating field-effect transistors, we observe that the introduction of zinc results in controlled p-doping. Finally, we show that zinc additives also enhance power conversion efficiencies and the stability of solar cells. Our results demonstrate substantially improved low-bandgap perovskites for solar cells and versatile electronic applications.
RESUMEN
BACKGROUND: Given the relatively sudden change from learner to teacher-provider that new consultants experience and the likely clinical and managerial challenges this may pose, there is a relative dearth of research into the problems they may have in relation to their new roles, or how supported they feel by senior colleagues acting in a mentoring role. This research sought to determine new consultants views on the quality and relevance of their training, its relationship to their confidence in clinical and managerial skills and their views on mentorship by senior colleagues. METHODS: Detailed postal questionnaire to new consultants using open and closed questions. Open questionnaire to established consultants to validate new consultant responses. RESULTS: Respondents felt their clinical training was good and were generally confident in most clinical skills although some perceived deficiencies in more complex procedures and specialist areas. Most lacked confidence in many managerial skills. These perceptions were verified by established consultants. Although no relationship was found between total training time or quality of training with confidence, extra training in specific sub-specialities improved confidence in these areas. While most established consultants thought that mentorship would be useful for new consultants, only 52% of them shared this view. CONCLUSION: Training and experience in management should be given greater emphasis. There may be a need for specific, targeted training in complex procedures for doctors who experience lack of confidence in these areas. Mentorship should be offered to new consultants and recognised in the job-plan of the new consultant contract.
Asunto(s)
Actitud del Personal de Salud , Educación Médica/normas , Cuerpo Médico de Hospitales/psicología , Evaluación de Necesidades , Ortopedia/educación , Rol del Médico , Competencia Clínica , Humanos , Mentores , Ortopedia/organización & administración , Encuestas y Cuestionarios , Reino UnidoRESUMEN
PURPOSE: To explore senior nurses' views of pre-registration house officer (PRHO) training, including the scope for their contribution to the new Foundation Programme. DESIGN: Data reported here are drawn from a larger, national project, which aimed to identify a curriculum for the PRHO year. The project was based in the Education Development Unit, Scottish Council for Postgraduate Medical and Dental Education (SCPMDE), Dundee. As part of the project, 40 semistructured interviews, each lasting about 1 hour, were held with senior nurses. Interviews were fully transcribed and coded in the qualitative software NVivo for further analysis. Codes were studied for emergent themes and categories. PARTICIPANTS: Senior nurses (10 from each of the 4 postgraduate regions of Scotland), from diverse specialties. RESULTS: Data suggest considerable cross- regional/specialty consistency. Key emergent themes concerned the process of training as much as the educational outcomes. The nurses focused on the development of outcomes such as communication and teamworking in addition to clinical and practical skills. They guided the PRHOs informally, but were concerned that their own extended roles were detracting from this. DISCUSSION: Nurses are gaining increasingly advanced professional, clinical and practical skills. Traditionally, experienced nurses guide and support PRHOs, at least informally. Data collected suggested there may be scope for capitalising on their expertise, including formalising aspects of their contribution to the proposed PRHO Foundation Programme. However, this is a potentially sensitive area and more interprofessional dialogue is needed.