Experimental Investigation on Hardware and Triggering Effect in Tip-Timing Measurement Uncertainty.

Non-destructive testing for structural health monitoring is becoming progressively important for gas turbine manufacturers. As several techniques for diagnostics and condition-based maintenance have been developed over the years, the tip-timing approach is one of the preferred approaches for characterizing the dynamic behavior of turbine blades using non-contact probes. This experimental work investigates the uncertainty of the time-of-arrival of a Blade Tip-Timing measurement system, a fundamental requirement for numerical and aeromechanical modeling validation. The study is applied to both the measurement setup and the data processing procedure of a generic commercial measurement system. The influence of electronic components and signal processing on the tip-timing uncertainty is determined under different operating conditions.

State-Space Model for Arrival Time Simulations and Methodology for Offline Blade Tip-Timing Software Characterization.

Blade tip-timing is an extensively used technique for measuring blade vibrations in turbine and compressor stages; it is one of the preferred techniques used for characterizing their dynamic behaviors using non-contact probes. Typically, arrival time signals are acquired and processed by a dedicated measurement system. Performing a sensitivity analysis on the data processing parameters is essential for the proper design of tip-timing test campaigns. This study proposes a mathematical model for generating synthetic tip-timing signals, descriptive of specific test conditions. The generated signals were used as the controlled input for a thorough characterization of post-processing software for tip-timing analysis. This work represents the first step in quantifying the uncertainty introduced by tip-timing analysis software into user measurements. The proposed methodology can also offer essential information for further sensitivity studies on parameters that influence the accuracy of data analysis during testing.

Evaluation of the Accuracy of Four Digital Methods by Linear and Volumetric Analysis of Dental Impressions.

The quality of dental arch impression has a substantial role in the precision of the intervention. It is traditionally acquired with resins that solidify when in contact with the air. Compared to that method, digital impression gives great advantages and, together with three-dimensional (3D) digitization devices, allows a simplification of the digital impression process. The growing adoption of such systems by a large number of dental clinics determines the need for an in-depth evaluation of the accuracy and the precision of the different systems. The aim of this work is to define a methodology for the evaluation of the accuracy and precision of 3D intraoral and desktop scanning systems, by using volumetric and linear methods. The replica of a tooth was realized with zirconium; afterward, high-accuracy point clouds of the master model were acquired by a coordinate measurement machine (CMM). In this way, the dimensions of the replica were accurately known. An intraoral scanner (I) and three desktops (D1, D2, D3) were then used to scan the replica. The geometry resulting from the CMM was compared with the ones derived from the scanners, using two different commercial programs (Geomagic and 3-Matic) and a custom-developed algorithm (MATLAB). Geomagic showed the mean values to be in a range from 0.0286 mm (D1) to 0.1654 mm (I), while 3-Matic showed mean values from -0.0396 mm (D1) to 0.1303 mm (I). MATLAB results ranged from 0.00014 mm (D1) to 0.00049 mm (D2). The probability distributions of the volumetric error of the measurements obtained with the different scanners allow a direct comparison of their performances. For the results given by our study, the volumetric approach that we adopted appears to be an excellent system of analysis.

Fibre Bragg Gratings for the Monitoring of Wooden Structures.

The aim of this work was to develop and validate an experimental methodology suitable for analysing on-site the behaviour of fibre-reinforced wooden structures. The proposed measurement method is based on the application of fibre Bragg grating (FBG) strain sensors. An analysis of adhesive behaviour was performed preliminarily, which provided indications for choosing the type of adhesive and for the fibre bonding length in accordance with the volume of measurement. The first series of tests was carried out on wood samples to verify the coupling between the measuring sensor and the wood support when the latter is subject to mechanical stresses. The second investigation was done on site to test the behaviour of a historical wood floor before and after reinforcement by means of a series of tests performed using optical fibres with the Bragg grating. The optical fibre system measurements were compared to those obtained using a laser vibrometer, a measurement system of proven stability and precision. The comparison makes it possible to confirm the validity of the results and the reliability of the system for the monitoring of historic wooden structures.

Image Analysis Technique for Material Behavior Evaluation in Civil Structures.

The article presents a hybrid monitoring technique for the measurement of the deformation field. The goal is to obtain information about crack propagation in existing structures, for the purpose of monitoring their state of health. The measurement technique is based on the capture and analysis of a digital image set. Special markers were used on the surface of the structures that can be removed without damaging existing structures as the historical masonry. The digital image analysis was done using software specifically designed in Matlab to follow the tracking of the markers and determine the evolution of the deformation state. The method can be used in any type of structure but is particularly suitable when it is necessary not to damage the surface of structures. A series of experiments carried out on masonry walls of the Oliverian Museum (Pesaro, Italy) and Palazzo Silvi (Perugia, Italy) have allowed the validation of the procedure elaborated by comparing the results with those derived from traditional measuring techniques.