Environmental footprint and material composition comparison of single-use and reusable duodenoscopes.

BACKGROUND: Infection outbreaks associated with contaminated reusable duodenoscopes (RUDs) have induced the development of novel single-use duodenoscopes (SUDs). This study aimed to analyze the material composition and life cycle assessment (LCA) of RUDs and SUDs to assess the sustainability of global and partial SUD implementation. METHODS: A single-center study evaluated material composition analysis and LCA of one RUD and two SUDs from different manufacturers (A/B). Material composition analysis was performed to evaluate the thermochemical properties of the duodenoscope components. The carbon footprint was calculated using environmental software. We compared the sustainability strategies of universal use of RUDs, frequent use of RUDs with occasional SUDs, and universal use of SUDs over the lifetime of one RUD. RESULTS: RUDs were substantially heavier (3489 g) than both SUD-A (943 g) and SUD-B (716 g). RUDs were mainly metal alloys (95%), whereas SUDs were mainly plastic polymers and resins (70%-81%). The LCA demonstrated the sustainability of RUDs, with a life cycle carbon footprint 62-82 times lower than universal use of SUDs (152 vs. 10 512-12 640 kg CO2eq) and 10 times lower than occasional use of SUDs (152 vs. 1417-1677 kg CO2eq). Differences were observed between SUD-A and SUD-B (7.9 vs. 6.6 kg CO2eq per endoscope). End-of-life incineration emissions for SUDs were the greatest environmental contributors. CONCLUSIONS: Widespread adoption of SUDs has greater environmental challenges; it requires a balance between infection control and environmental responsibility. Carbon footprint labelling can help healthcare institutions make sustainable choices and promote environmentally responsible healthcare practices.

Life cycle assessment of routinely used endoscopic instruments and simple intervention to reduce our environmental impact.

OBJECTIVES: GI endoscopy units represent the third largest producers of medical waste. We aimed to determine endoscopic instrument composition and life cycle assessment (LCA) and to assess a sustainability proposal based on a mark on the instruments that identifies parts can be safely recycled or 'green mark'. DESIGN: Material composition analysis and LCA of forceps, snares and clips from four different manufacturers (A-D) were performed with four different methods. Carbon footprint from production, transportation and end of life of these instruments was calculated. In 30 consecutive procedures, we marked the contact point with the working channel. 5 cm away from that point was considered as green mark. One-week prospective study was conducted with 184 procedures evaluating 143 instruments (75 forceps, 49 snares and 19 haemoclips) to assess the efficacy of this recyclable mark. RESULTS: Composition from different manufacturers varied widely. Most common materials were high global warming potential (GWP) waste (polyethylene, polypropylene and acrylonitrile) and low GWP waste (stainless steel). Significant differences were found for the forceps (0.31-0.47 kg of CO2 equivalent (CO2-eq)) and haemoclips (0.41-0.57 kg CO2-eq) between the manufacturers. Green mark was established 131.26 cm for gastroscope and 195.32 cm for colonoscope. One-week activity produced 67.74 kg CO2-eq. Applying our sustainability intervention, we could reduce up to 27.44% (18.26 kg CO2-eq). This allows the recycling of 61.7% of the instrument total weight (4.69 kg). CONCLUSION: Knowledge of carbon footprint is crucial to select the most sustainable alternatives because there are large variations between brands. A mark to identify recyclable parts could reduce our environmental impact significantly.

Materials Science Toolkit for Carbon Footprint Assessment: A Case Study for Endoscopic Accessories of Common Use.

Ironically, healthcare systems are key agents in respiratory-related diseases and estimated deaths because of the high impact of their greenhouse gas emissions, along with industry, transportation, and housing. Based on safety requirements, hospitals and related services use an extensive number of consumables, most of which end up incinerated at the end of their life cycle. A thorough assessment of the carbon footprint of such devices typically requires knowing precise information about the manufacturing process, which is rarely available in detail because of the many materials, pieces, and steps involved during the fabrication. Yet, the tools most often used for determining the environmental impact of consumer goods require a bunch of parameters, mainly based on the material composition of the device. Here, we report a basic set of analytical methods that provide the information required by the software OpenLCA to calculate the main outcome related to environmental impact, greenhouse gas emissions. Through thermogravimetry, calorimetry, infrared spectroscopy, and elemental analysis, we proved that obtaining relevant data for the calculator in the exemplifying case of endoscopy tooling or accessories is possible. This routine procedure opens the door to a broader, more accurate analysis of the environmental impact of everyday work at hospital services, offering potential alternatives to minimize it.

Influence of pre-polymerisation atmosphere on the properties of pre- and poly(glycerol sebacate).

Poly(glycerol sebacate) (PGS) is a versatile biodegradable biomaterial on account of its adjustable mechanical properties as an elastomeric polyester. Nevertheless, it has shown dissimilar results when synthesised by different research groups under equivalent synthesis conditions. This lack of reproducibility proves how crucial it is to understand the effect of the parameters involved on its manufacturing and characterize the polymer networks obtained. Several studies have been conducted in recent years to understand the role of temperature, time, and the molar ratio of its monomers, while the influence of the atmosphere applied during its pre-polymerisation remained unknown. The results obtained here allow for a better understanding about the effect of inert (Ar and N2) and oxidative (oxygen, dry air, and humid air) atmospheres on the extent of the reaction. The molecular pattern of intermediate pre-polymers and the gelation time and morphology of their corresponding cured PGS networks were studied as well. Overall, inert atmospheres promote a rather linear growth of macromers, with scarce branches, resulting in loose elastomers with long chains mainly crosslinked. Conversely, oxygen in the latter atmospheres promotes branching through secondary hydroxyl groups, leading to less-crosslinked 'defective' networks. In this way, the pre-polymerisation atmosphere could be used advantageously to adjust the reactivity of secondary hydroxyls, in order to modulate branching in the elastomeric PGS networks obtained to suit the properties required in a particular application.

Role of Curing Temperature of Poly(Glycerol Sebacate) Substrates on Protein-Cell Interaction and Early Cell Adhesion.

A novel procedure to obtain smooth, continuous polymeric surfaces from poly(glycerol sebacate) (PGS) has been developed with the spin-coating technique. This method proves useful for separating the effect of the chemistry and morphology of the networks (that can be obtained by varying the synthesis parameters) on cell-protein-substrate interactions from that of structural variables. Solutions of the PGS pre-polymer can be spin-coated, to then be cured. Curing under variable temperatures has been shown to lead to PGS networks with different chemical properties and topographies, conditioning their use as a biomaterial. Particularly, higher synthesis temperatures yield denser networks with fewer polar terminal groups available on the surface. Material-protein interactions were characterised by using extracellular matrix proteins such as fibronectin (Fn) and collagen type I (Col I), to unveil the biological interface profile of PGS substrates. To that end, atomic force microscopy (AFM) images and quantification of protein adsorbed in single, sequential and competitive protein incubations were used. Results reveal that Fn is adsorbed in the form of clusters, while Col I forms a characteristic fibrillar network. Fn has an inhibitory effect when incubated prior to Col I. Human umbilical endothelial cells (HUVECs) were also cultured on PGS surfaces to reveal the effect of synthesis temperature on cell behaviour. To this effect, early focal adhesions (FAs) were analysed using immunofluorescence techniques. In light of the results, 130 °C seems to be the optimal curing temperature since a preliminary treatment with Col I or a Fn:Col I solution facilitates the formation of early focal adhesions and growth of HUVECs.