Using Redox-Switchable Polymerization Catalysis to Synthesize a Chemically Recyclable Thermoplastic Elastomer.

In an effort to synthesize chemically recyclable thermoplastic elastomers, a redox-switchable catalytic system was developed to synthesize triblock copolymers containing stiff poly(lactic acid) (PLA) end blocks and a flexible poly(tetrahydrofuran-co-cyclohexene oxide) (poly(THF-co-CHO) copolymer as the mid-block. The orthogonal reactivity induced by changing the oxidation state of the iron-based catalyst enabled the synthesis of the triblock copolymers in a single reaction flask from a mixture of monomers. The triblock copolymers demonstrated improved flexibility compared to poly(l-lactic acid) (PLLA) and thermomechanical properties that resemble thermoplastic elastomers, including a rubbery plateau in the range of -60 to 40 °C. The triblock copolymers containing a higher percentage of THF versus CHO were more flexible, and a blend of triblock copolymers containing PLLA and poly(d-lactic acid) (PDLA) end-blocks resulted in a stereocomplex that further increased polymer flexibility. Besides the low cost of lactide and THF, the sustainability of this new class of triblock copolymers was also supported by their depolymerization, which was achieved by exposing the copolymers sequentially to FeCl3 and ZnCl2 /PEG under reactive distillation conditions.

Broadband Achromatic Quarter-Waveplate Using 2D Hybrid Copper Halide Single Crystals.

Achromatic quarter waveplates (A-QWPs), traditionally constructed from multiple birefringent crystals, can modulate light polarization and retardation across a broad range of wavelengths. This mechanism is inherently related to phase retardation controlled by the fast and slow axis of stacked multi-birefringent crystals. However, the conventional design of A-QWPs requires the incorporation of multiple birefringent crystals, which complicates the manufacturing process and raises costs. Here, we report the discovery of a broadband (540-1060 nm) A-QWP based on a two-dimensional (2D) layered hybrid copper halide (HCH) perovskite single crystal. The 2D copper chloride (CuCl6) layers of the HCH crystal undergo Jahn-Teller distortion and subsequently trigger the in-plane optical birefringence. Its broad range of the wavelength response as an A-QWP is a consequence of the out-of-plane mosaicity formed among the stacked inorganic layers during the single-crystal self-assembly process in the solution phase. Given the versatility of 2D hybridhalide perovskites, the 2D HCH crystal offers a promising approach for designing cost-effective A-QWPs and the ability to integrate other optical devices.

X-ray scattering as an effective tool for characterizing liquid metal composite morphology.

Quantitative analysis of particle size and size distribution is crucial in establishing structure-property relationships of composite materials. An emerging soft composite architecture involves dispersing droplets of liquid metal throughout an elastomer, enabling synergistic properties of metals and soft polymers. The structure of these materials is typically characterized through real-space microscopy and image analysis; however, these techniques rely on magnified images that may not represent the global-averaged size and distribution of the droplets. In this study, we utilize ultra-small angle X-ray scattering (USAXS) as a reciprocal-space characterization technique that yields global-averaged dimensions of eutectic gallium indium (EGaIn) alloy soft composites. The Unified fit and Monte Carlo scattering methods are applied to determine the particle size and size distributions of the liquid metal droplets in the composites and are shown to be in excellent agreement with results from real-space image analysis. Additionally, all methods indicate that the droplets are getting larger as they are introduced into composites, suggesting that the droplets are agglomerating or possibly coalescing during dispersion. This work demonstrates the viability of X-ray scattering to elucidate structural information about liquid metal droplets for material development for applications in soft robotics, soft electronics, and multifunctional materials.

Quadruple Hydrogen Bond-Containing A-AB-A Triblock Copolymers: Probing the Influence of Hydrogen Bonding in the Central Block.

This work reveals the influence of pendant hydrogen bonding strength and distribution on self-assembly and the resulting thermomechanical properties of A-AB-A triblock copolymers. Reversible addition-fragmentation chain transfer polymerization afforded a library of A-AB-A acrylic triblock copolymers, wherein the A unit contained cytosine acrylate (CyA) or post-functionalized ureido cytosine acrylate (UCyA) and the B unit consisted of n-butyl acrylate (nBA). Differential scanning calorimetry revealed two glass transition temperatures, suggesting microphase-separation in the A-AB-A triblock copolymers. Thermomechanical and morphological analysis revealed the effects of hydrogen bonding distribution and strength on the self-assembly and microphase-separated morphology. Dynamic mechanical analysis showed multiple tan delta (δ) transitions that correlated to chain relaxation and hydrogen bonding dissociation, further confirming the microphase-separated structure. In addition, UCyA triblock copolymers possessed an extended modulus plateau versus temperature compared to the CyA analogs due to the stronger association of quadruple hydrogen bonding. CyA triblock copolymers exhibited a cylindrical microphase-separated morphology according to small-angle X-ray scattering. In contrast, UCyA triblock copolymers lacked long-range ordering due to hydrogen bonding induced phase mixing. The incorporation of UCyA into the soft central block resulted in improved tensile strength, extensibility, and toughness compared to the AB random copolymer and A-B-A triblock copolymer comparisons. This study provides insight into the structure-property relationships of A-AB-A supramolecular triblock copolymers that result from tunable association strengths.

Regioselective Bromination of the Dextran Nonreducing End Creates a Pathway to Dextran-Based Block Copolymers.

Preparation of polysaccharide-based block copolymers with linear architectures is an important goal, opening up clear application potential and requiring significant advances in polysaccharide regio- and chemoselectivity. Herein we report a simple approach to prepare dextran-based block copolymers. Reaction with N-bromosuccinimide (NBS)/triphenyl phosphine (PPh3) regioselectively brominates the sole primary alcohol of linear, unbranched dextran at C-6 of the nonreducing end monosaccharide. The resulting dextran, monofunctionalized with a terminal C-6 bromide, was coupled with various amine terminated polymers to prepare block copolymers, including dextran-b-poly(ethylene glycol), dextran-b-polystyrene, and dextran-b-poly(N-isopropylacrylamide). These renewable-based block copolymers, prepared in two selective, high-yielding steps from native linear dextran, exhibit various interesting properties. Dextran-b-poly(N-isopropylacrylamide) undergoes thermally induced micellization as revealed by dynamic light scattering (DLS), forming micelles upon exceeding 33 °C. We also observed microphase separation in dextran-b-polystyrene by using small-angle X-ray scattering (SAXS). Overall, this methodology provides a new, highly chemo- and regioselective, versatile route to diverse dextran-based block copolymers with useful properties, enabling drug delivery, compatibilization, and other applications.

Increased Water Reduction Efficiency of Polyelectrolyte-Bound Trimetallic [Ru,Rh,Ru] Photocatalysts in Air-Saturated Aqueous Solutions.

The groundbreaking use of polyelectrolytes to increase the efficiency of supramolecular photocatalysts in solar H2 production schemes under aqueous aerobic conditions is reported. Supramolecular photocatalysts of the architecture [{(TL)2 Ru(BL)}2 RhX2 ](5+) (BL=bridging ligand, TL=terminal ligand, X=halide) demonstrate high efficiencies in deoxygenated organic solvents but do not function in air-saturated aqueous solution because of the quenching of the metal-to-ligand charge-transfer (MLCT) excited state under these conditions. The new photocatalytic system incorporates poly(4-styrenesulfonate) (PSS) into aqueous solutions containing [{(bpy)2 Ru(dpp)}2 RhCl2 ](5+) (bpy=2,2'-bipyridine, dpp=2,3-bis(2-pyridyl)pyrazine). PSS has a profound impact on the photocatalyst efficiency, increasing H2 production over three times that of deoxygenated aqueous solutions alone. H2 photocatalysis proceeds even under aerobic conditions for PSS-containing solutions, an exciting consequence for solar hydrogen-production research.

Solution properties and electrospinning of phosphonium gemini surfactants.

Bis(diphenylphosphino)alkanes quantitatively react with excess 1-bromododecane to prepare novel phosphonium gemini surfactants with spacer lengths ranging from 2 to 4 methylenes (12-2/3/4-12P). Dodecyltriphenylphosphonium bromide (DTPP), a monomeric surfactant analog, was readily water soluble, however, in sharp contrast, phosphonium gemini surfactants were poorly soluble in water due to two hydrophobic tails and relatively hydrophobic cationic head groups containing phenyl substituents. Isothermal titration calorimetry did not reveal a measurable critical micelle concentration for the 12-2-12P phosphonium gemini surfactant in water at 25 °C. Subsequent studies in 50/50 v/v water-methanol at 25 °C showed a CMC of 1.0 mM for 12-2-12P. All phosphonium gemini surfactants effectively complexed nucleic acids, but failed to deliver nucleic acids in vitro to HeLa cells. The solution behavior of phosphonium gemini surfactants was investigated in chloroform, which is an organic solvent where reverse micellar structures are favored. Solution rheology in chloroform explored the solution behavior of the phosphonium gemini surfactants compared to DTPP. The 12-2-12P and 12-3-12P gemini surfactants were successfully electrospun from chloroform to generate uniform fibers while 12-4-12P gemini surfactant and DTPP only electrosprayed to form droplets.

A photosynthetic alveolate closely related to apicomplexan parasites.

Many parasitic Apicomplexa, such as Plasmodium falciparum, contain an unpigmented chloroplast remnant termed the apicoplast, which is a target for malaria treatment. However, no close relative of apicomplexans with a functional photosynthetic plastid has yet been described. Here we describe a newly cultured organism that has ultrastructural features typical for alveolates, is phylogenetically related to apicomplexans, and contains a photosynthetic plastid. The plastid is surrounded by four membranes, is pigmented by chlorophyll a, and uses the codon UGA to encode tryptophan in the psbA gene. This genetic feature has been found only in coccidian apicoplasts and various mitochondria. The UGA-Trp codon and phylogenies of plastid and nuclear ribosomal RNA genes indicate that the organism is the closest known photosynthetic relative to apicomplexan parasites and that its plastid shares an origin with the apicoplasts. The discovery of this organism provides a powerful model with which to study the evolution of parasitism in Apicomplexa.

High Modulus, Strut-like poly(ether ether ketone) Aerogels Produced from a Benign Solvent.

Poly(ether ether ketone) (PEEK) was found to form gels in the benign solvent 1,3-diphenylacetone (DPA). Gelation of PEEK in DPA was found to form an interconnected, strut-like morphology composed of polymer axialites. To our knowledge, this is the first report of a strut-like morphology for PEEK aerogels. PEEK/DPA gels were prepared by first dissolving PEEK in DPA at 320 °C. Upon cooling to 50 °C, PEEK crystallizes and forms a gel in DPA. The PEEK/DPA phase diagram indicated that phase separation occurs by solid-liquid phase separation, implying that DPA is a good solvent for PEEK. The Flory-Huggins interaction parameter, calculated as χ12 = 0.093 for the PEEK/DPA system, confirmed that DPA is a good solvent for PEEK. PEEK aerogels were prepared by solvent exchanging DPA to water then freeze-drying. PEEK aerogels were found to have densities between 0.09 and 0.25 g/cm3, porosities between 80 and 93%, and surface areas between 200 and 225 m2/g, depending on the initial gel concentration. Using nitrogen adsorption analyses, PEEK aerogels were found to be mesoporous adsorbents, with mesopore sizes of about 8 nm, which formed between stacks of platelike crystalline lamellae. Scanning electron microscopy and X-ray scattering were utilized to elucidate the hierarchical structure of the PEEK aerogels. Morphological analysis found that the PEEK/DPA gels were composed of a highly nucleated network of PEEK axialites (i.e., aggregates of stacked crystalline lamellae). The highly connected axialite network imparted robust mechanical properties on PEEK aerogels, which were found to densify less upon freeze-drying than globular PEEK aerogel counterparts gelled from dichloroacetic acid (DCA) or 4-chlorphenol (4CP). PEEK aerogels formed from DPA were also found to have a modulus-density scaling that was far more efficient in supporting loads than the poorly connected aerogels formed from PEEK/DCA or PEEK/4CP solutions. The strut-like morphology in these new PEEK aerogels also significantly improved the modulus to a degree that is comparable to high-performance crosslinked aerogels based on polyimide and polyurea of comparable densities.

Additive Manufacturing of Poly(phenylene Sulfide) Aerogels via Simultaneous Material Extrusion and Thermally Induced Phase Separation.

Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre-prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room-temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer-wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze-drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0-74.8%) and densities (0.345-0.684 g cm-3 ), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

Operando characterization and regulation of metal dissolution and redeposition dynamics near battery electrode surface.

Mn dissolution has been a long-standing, ubiquitous issue that negatively impacts the performance of Mn-based battery materials. Mn dissolution involves complex chemical and structural transformations at the electrode-electrolyte interface. The continuously evolving electrode-electrolyte interface has posed great challenges for characterizing the dynamic interfacial process and quantitatively establishing the correlation with battery performance. In this study, we visualize and quantify the temporally and spatially resolved Mn dissolution/redeposition (D/R) dynamics of electrochemically operating Mn-containing cathodes. The particle-level and electrode-level analyses reveal that the D/R dynamics is associated with distinct interfacial degradation mechanisms at different states of charge. Our results statistically differentiate the contributions of surface reconstruction and Jahn-Teller distortion to the Mn dissolution at different operating voltages. Introducing sulfonated polymers (Nafion) into composite electrodes can modulate the D/R dynamics by trapping the dissolved Mn species and rapidly establishing local Mn D/R equilibrium. This work represents an inaugural effort to pinpoint the chemical and structural transformations responsible for Mn dissolution via an operando synchrotron study and develops an effective method to regulate Mn interfacial dynamics for improving battery performance.

Linear coupling of alignment with transport in a polymer electrolyte membrane.

Polymer electrolyte membranes (PEMs) selectively transport ions and polar molecules in a robust yet formable solid support. Tailored PEMs allow for devices such as solid-state batteries,'artificial muscle' actuators and reverse-osmosis water purifiers. Understanding how PEM structure and morphology relate to mobile species transport presents a challenge for designing next-generation materials. Material length scales from subnanometre to 1 µm influence bulk properties such as ion conductivity and water transport. Here we employ multi-axis pulsed-field-gradient NMR to measure diffusion anisotropy, and (2)H NMR spectroscopy and synchrotron small-angle X-ray scattering to probe orientational order as a function of water content and of membrane stretching. Strikingly, transport anisotropy linearly depends on the degree of alignment, signifying that membrane stretching affects neither the nanometre-scale channel dimensions nor the defect structure,causing only domain reorientation. The observed reorientation of anisotropic domains without perturbation of the inherent nematic-like domain character parallels the behaviour of nematic elastomers, promises tailored membrane conduction and potentially allows understanding of tunable shape-memory effects in PEM materials. This quantitative understanding will drive PEM design efforts towards optimal membrane transport, thus enabling more efficient polymeric batteries, fuel cells, mechanical actuators and water purification.

Ultrathin chitin films for nanocomposites and biosensors.

Chitin is the second most abundant biopolymer and insight into its natural synthesis, enzymatic degradation, and chemical interactions with other biopolymers is important for bioengineering with this renewable resource. This work is the first report of smooth, homogeneous, ultrathin chitin films, opening the door to surface studies of binding interactions, adsorption kinetics, and enzymatic degradation. The chitin films were formed by spincoating trimethylsilyl chitin onto gold or silica substrates, followed by regeneration to a chitin film. Infrared and X-ray photoelectron spectroscopy, X-ray diffraction, ellipsometry, and atomic force microscopy were used to confirm the formation of smooth, homogeneous, and amorphous chitin thin films. Quartz crystal microbalance with dissipation monitoring (QCM-D) solvent exchange experiments showed these films swelled with 49% water by mass. The utility of these chitin films as biosensors was evident from QCM-D and surface plasmon resonance studies that revealed the adsorption of a bovine serum albumin monolayer.

Lithium oxides precipitation in nonaqueous Li-air batteries.

Lithium-air/oxygen battery is a rising star in the field of electrochemical energy storage as a promising alternative to lithium ion batteries. Nevertheless, this alluring system is still at its infant stage, and the breakthrough of lithium-air batteries into the energy market is currently constrained by a combination of scientific and technical challenges. Targeting at the air electrode in nonaqueous lithium-air batteries, this review attempts to summarize the knowledge about the fundamentals related to lithium oxides precipitation, which has been one of the vital and attractive aspects of the research communities of science and technology.

Designing synergistic crystallization inhibitors: Bile salt derivatives of cellulose with enhanced hydrophilicity.

Crystallization inhibitors in amorphous solid dispersions (ASD) enable metastable supersaturated drug solutions that persist for a physiologically relevant time. Olefin cross-metathesis (CM) has successfully provided multifunctional cellulose-based derivatives as candidate ASD matrix polymers. In proof of concept studies, we prepared hydrophobic bile salt/cellulose adducts by CM with naturally occurring bile salts. We hypothesized that increased hydrophilicity would enhance the ability of these conjugates to maximize bioactive supersaturation. Their selective preparation presents a significant synthetic challenge, given polysaccharide reactivity and polysaccharide and bile salt complexity. We prepared such derivatives using a more hydrophilic hydroxypropyl cellulose (HPC) backbone, employing a pent-4-enyl tether (Pen) for appending bile acids. We probed structure-property relationships by varying the nature and degree of substitution of the bile acid substituent (lithocholic or deoxycholic acid). These conjugates are indeed synergistic inhibitors, as demonstrated with the fast-crystallizing prostate cancer drug, enzalutamide. The lithocholic acid methyl ester derivative, AcrMLC-PenHHPCPen (0.64), increased induction time 68 fold vs. drug alone.

High-Strength Liquid Crystal Polymer-Graphene Oxide Nanocomposites from Water.

We report on the morphology and mechanical properties of nanocomposite films derived from aqueous, hybrid liquid crystalline mixtures of rodlike aggregates of a sulfonated, all-aromatic polyamide, poly(2,2'-disulfonyl-4,4'-benzidine terephthalamide) (PBDT), and graphene oxide (GO) platelets. An isothermal step at 200 °C facilitates in situ partial thermal reduction of GO to reduced GO (rGO) in nanocomposite films. X-ray scattering studies reveal that PBDT-rGO nanocomposites exhibit both higher in-plane alignment of PBDT (the order parameter increases from 0.79 to 0.9 at 1.8 vol % rGO) and alignment along the casting direction (from 0.1 to 0.6 at 1.8 vol % rGO). From dynamic mechanical thermal analysis, the interaction between PBDT and rGO causes the ß-relaxation activation energy for PBDT to increase with rGO concentration. Modulus mapping of nanocomposites using atomic force microscopy demonstrates enhanced local stiffness, indicating reinforcement. From stress-strain analysis, the average Young's modulus increases from 16 to 37 GPa at 1.8 vol % rGO and the average tensile strength increases from 210 to 640 MPa. Despite polymer alignment along the casting direction, an average transverse tensile strength of 230 MPa is obtained.

Graphene-based electrochemical energy conversion and storage: fuel cells, supercapacitors and lithium ion batteries.

Graphene has attracted extensive research interest due to its strictly 2-dimensional (2D) structure, which results in its unique electronic, thermal, mechanical, and chemical properties and potential technical applications. These remarkable characteristics of graphene, along with the inherent benefits of a carbon material, make it a promising candidate for application in electrochemical energy devices. This article reviews the methods of graphene preparation, introduces the unique electrochemical behavior of graphene, and summarizes the recent research and development on graphene-based fuel cells, supercapacitors and lithium ion batteries. In addition, promising areas are identified for the future development of graphene-based materials in electrochemical energy conversion and storage systems.

Understanding the Mechanical Reinforcement of Metal-Organic Framework-Polymer Composites: The Effect of Aspect Ratio.

The aspect ratio (AR) of filler particles is one of the most critical determinants for the mechanical properties of particle-reinforced polymer composites. However, it has been challenging to solely study the effect of particle AR due to the difficulties of controlling AR without altering the physical and chemical properties of the particle. Herein, we synthesized PCN-222, a zirconium-based porphyrinic metal-organic framework (MOF) with preferential longitudinal growth as a series of particles with ARs increasing from 3.4 to 54. The synthetic MOF conditions allowed for the chemical properties of the particles to remain constant over the series. The particles were employed as reinforcers for poly(methyl methacrylate) (PMMA). MOF-polymer composite films were fabricated using doctor-blading techniques, which facilitated particle dispersion and alignment in the PMMA matrix, as revealed by optical microscopy and wide-angle X-ray diffraction. Mechanical measurements showed that both elastic and dynamic moduli increased with particle AR and particle concentrations but started to decrease as particle loading increased beyond 0.5 wt % (1.12 vol %). The data obtained at low particle loadings were fitted well with the Halpin-Tsai model. In contrast, the percolation model and the Cox model were unable to adequately fit the data, indicating the mechanical reinforcement in our system mainly originated from efficient load transfer between particles and the matrix in the particle orienting direction. Finally, we showed that the thermal stability of composite films increased with the addition of MOF particles because of the high thermal degradation temperature and restricted polymer chain mobility.

Quadruple Hydrogen Bonding Supramolecular Elastomers for Melt Extrusion Additive Manufacturing.

This manuscript describes the versatility of highly directional, noncovalent interactions, i.e., quadruple hydrogen bonding (QHB), to afford novel polyurea segmented supramolecular polymers for melt extrusion three-dimensional (3D) printing processes. The molecular design of the polyurea elastomers features (1) flexible polyether segments and relatively weak urea hydrogen-bonding sites in the soft segments to provide elasticity and toughness, and (2) strong ureido-cytosine (UCyt) QHB in the hard segments to impart enhanced mechanical integrity. The resulting polyureas were readily compression-molded into mechanically-robust, transparent, and creasable films. Optimization of polyurea composition offered a rare combination of high tensile strength (95 MPa), tensile elongation (788% strain), and toughness (94 MJ/m3), which are superior to a commercially available Ninjaflex elastomer. The incorporation of QHB facilitated melt processability, where hydrogen bonding dissociation provided low viscosities at printing temperatures. During cooling, directional self-assembly of UCyt QHB facilitated the solidification process and contributed to part fidelity with the formation of a robust physical network. The printed objects displayed high layer fidelity, smooth surfaces, minimal warpage, and complex geometries. The presence of highly directional QHB effectively diminished mechanical anisotropy, and the printed samples exhibited comparable Young's moduli along (x-y direction, 0°) and perpendicular to (z-direction, 90°) the layer direction. Remarkably, the printed samples exhibited ultimate tensile strains approaching 500% in the z-direction prior to failure, which was indicative of improved interlayer adhesion. Thus, this design paradigm, which is demonstrated for novel polyurea copolymers, suggests the potential of supramolecular polymers with enhanced mechanical performance, melt processability, recyclability, and improved interlayer adhesion for melt extrusion additive manufacturing processes.

Hierarchical Morphology of Poly(ether ether ketone) Aerogels.

The phase diagram for the thermoreversible gelation of poly(ether ether ketone) (PEEK) in 4-chlorophenol (4CP) was constructed over broad temperature and concentration ranges, revealing that PEEK is capable of dissolving and forming gels in both 4CP and dichloroacetic acid (DCA) up to a concentration of 25 wt %. Highly porous aerogels of PEEK were prepared through simple solvent exchange followed by one of two drying methods of solvent removal from the wet gel: freeze-drying or supercritical CO2 fluid extraction (SC-drying). The field-emission scanning electron microscopy analysis showed that gelation of PEEK in 4CP, followed by SC-drying, produced aerogels with well-defined lamellar aggregates as compared to less ordered aggregates formed from DCA. Mechanical properties (in compression) were shown to improve with increasing density, resulting in equivalent compressive moduli at comparable density, regardless of the preparation method (gelation solvent selection, concentration variation, or drying method). Nitrogen adsorption-desorption isotherms indicate that PEEK aerogels are comprised of mesopores (2-50 nm diameter pores) formed from stacked crystalline lamella. PEEK aerogels prepared using SC-drying exhibit higher Brunauer-Emmett-Teller surface areas than freeze-dried aerogels of comparable density. The ultra-small-angle X-ray scattering/small-angle X-ray scattering (SAXS)/wide-angle X-ray scattering analysis revealed a hierarchical morphology of the PEEK aerogels with structural features from PEEK crystallites to agglomerates of stacked lamella that spanned a wide range of length scales. SANS contrast-matching confirmed that the morphological origin of the principle scattering feature in PEEK aerogels is stacked crystalline lamella. Nitrogen sorption measurements of porosity and the specific surface area of the PEEK aerogels were correlated with the SAXS analysis to reveal a remarkably high surface area attributed to the platelet-like, lamellar morphology. Contact angle and contact angle hysteresis (CAH) revealed that low-density PEEK aerogels (ρ < 0.15 g/cm3) have water contact angles above the superhydrophobicity cutoff angle (>150°) and a very low CAH near 1°.