Optomechanical Generation of Coherent GHz Vibrations in a Phononic Waveguide.

Nanophononics has the potential for information transfer, in an analogous manner to its photonic and electronic counterparts. The adoption of phononic systems has been limited, due to difficulties associated with the generation, manipulation, and detection of phonons, especially at GHz frequencies. Existing techniques often require piezoelectric materials with an external radiofrequency excitation that are not readily integrated into existing CMOS infrastructures, while nonpiezoelectric demonstrations have been inefficient. In this Letter, we explore the optomechanical generation of coherent phonons in a suspended 2D silicon phononic crystal cavity with a guided mode around 6.8 GHz. By incorporating an air-slot into this cavity, we turn the phononic waveguide into an optomechanical platform that exploits localized photonic modes resulting from inherent fabrication imperfections for the transduction of mechanics. Such a platform exhibits very fine control of phonons using light, and is capable of coherent self-sustained phonon generation around 6.8 GHz, operating at room temperature. The ability to generate high frequency coherent mechanical vibrations within such a simple 2D CMOS-compatible system could be a first step towards the development of sources in phononic circuitry and the coherent manipulation of other solid-state properties.

Dispersion Mapping in 3-Dimensional Core-Shell Photonic Crystal Lattices Capable of Negative Refraction in the Mid-Infrared.

Engineering of the dispersion properties of a photonic crystal (PhC) opens a new paradigm for the design and function of PhC devices. Exploiting the dispersion properties of PhCs allows control over wave propagation within a PhC. We describe the design, fabrication, and experimental observation of photonic bands for 3D PhCs capable of negative refraction in the mid-infrared. Band structure and equifrequency contours were calculated to inform the design of 3D polymer-germanium core-shell PhCs, which were fabricated using two-photon lithography direct laser writing and sputtering. We successfully characterized a polymer-Ge core-shell lattice and mapped its band structure, which we then used to calculate the PhC refraction behavior. An analysis of wave propagation revealed that this 3D core-shell PhC refracts light negatively and possesses an effective negative index of refraction in the experimentally observed region. These results suggest that architected nanolattices have the potential to serve as new optical components and devices across infrared frequencies.

Additive Manufacturing of High-Refractive-Index, Nanoarchitected Titanium Dioxide for 3D Dielectric Photonic Crystals.

Additive manufacturing at small scales enables advances in micro- and nanoelectromechanical systems, micro-optics, and medical devices. Materials that lend themselves to AM at the nanoscale, especially for optical applications, are limited. State-of-the-art AM processes for high-refractive-index materials typically suffer from high porosity and poor repeatability and require complex experimental procedures. We developed an AM process to fabricate complex 3D architectures out of fully dense titanium dioxide (TiO2) with a refractive index of 2.3 and nanosized critical dimensions. Transmission electron microscopy (TEM) analysis proves this material to be rutile phase of nanocrystalline TiO2, with an average grain size of 110 nm and <1% porosity. Proof-of-concept woodpile architectures with 300-600 nm beam dimensions exhibit a full photonic band gap centered at 1.8-2.9 µm, as revealed by Fourier-transform infrared spectroscopy (FTIR) and supported by plane wave expansion simulations. The developed AM process enables advances in 3D MEMS, micro-optics, and prototyping of 3D dielectric PhCs.

Far-Field Radiative Thermal Rectification Based on Asymmetric Emissivity.

This experimental study investigates thermal rectification via asymmetric far-field thermal radiation on a fused silica slab. An asymmetrical distribution of surface emissivity is created over the device by partially covering the fused silica with a 100 nm thick aluminum film. The slab is subjected to a thermal bias, and when this bias is reversed, a small temperature difference is observed between the different configurations. This temperature difference arises from the difference in emissivity between the aluminum layer and fused silica, resulting in the transfer of thermal energy to the surrounding environment through radiation. Experimental findings are supported by finite element simulations, which not only confirm the measured values but also provide valuable insights into the rectification efficiency of the system. The rectification efficiency is found to be approximately 50% at room temperature for a thermal bias of 140 K. Simulations, which are performed by considering different environmental conditions experienced by the radiation and free convection processes, provide further insight into the underlying thermal rectification mechanism. These simulations consider an environmental temperature of 4 K for thermal radiation and an ambient temperature of 294 K for free convection and reveal an enhanced rectification effect with a rectification efficiency up to 600% when a thermal bias of 195 K is applied. This result emphasizes the significance of considering both convection and radiation in the thermal management and rectification of asymmetric systems. The outcomes of this study further our understanding of the thermal rectification phenomenon. They also show the importance of system asymmetry, emissivity disparities, environmental conditions, and the interplay between convection and radiation. Furthermore, the findings have implications for heat transfer and rectification in asymmetric systems, offering potential applications in areas such as energy harvesting, thermal management, and heat transfer optimization in electronic devices.

MoS2 phononic crystals for advanced thermal management.

Effective thermal management of electronic devices encounters substantial challenges owing to the notable power densities involved. Here, we propose layered MoS2 phononic crystals (PnCs) that can effectively reduce thermal conductivity (κ) with relatively small disruption of electrical conductivity (σ), offering a potential thermal management solution for nanoelectronics. These layered PnCs exhibit remarkable efficiency in reducing κ, surpassing that of Si and SiC PnCs with similar periodicity by ~100-fold. Specifically, in suspended MoS2 PnCs, we measure an exceptionally low κ down to 0.1 watts per meter kelvin, below the amorphous limit while preserving the crystalline structure. These findings are supported by molecular dynamics simulations that account for the film thickness, porosity, and temperature. We demonstrate the approach efficiency by fabricating suspended heat-routing structures that effectively confine and guide heat flow in prespecified directions. This study underpins the immense potential of layered materials as directional heat spreaders, thermal insulators, and active components for thermoelectric devices.

Application of Synchrotron Radiation-Based Fourier-Transform Infrared Microspectroscopy for Thermal Imaging of Polymer Thin Films.

The thermal imaging of surfaces with microscale spatial resolution over micro-sized areas remains a challenging and time-consuming task. Surface thermal imaging is a very important characterization tool in mechanical engineering, microelectronics, chemical process engineering, optics, microfluidics, and biochemistry processing, among others. Within the realm of electronic circuits, this technique has significant potential for investigating hot spots, power densities, and monitoring heat distributions in complementary metal-oxide-semiconductor (CMOS) platforms. We present a new technique for remote non-invasive, contactless thermal field mapping using synchrotron radiation-based Fourier-transform infrared microspectroscopy. We demonstrate a spatial resolution better than 10 um over areas on the order of 12,000 um2 measured in a polymeric thin film on top of CaF2 substrates. Thermal images were obtained from infrared spectra of poly(methyl methacrylate) thin films heated with a wire. The temperature dependence of the collected infrared spectra was analyzed via linear regression and machine learning algorithms, namely random forest and k-nearest neighbor algorithms. This approach speeds up signal analysis and allows for the generation of hyperspectral temperature maps. The results here highlight the potential of infrared absorbance to serve as a remote method for the quantitative determination of heat distribution, thermal properties, and the existence of hot spots, with implications in CMOS technologies and other electronic devices.

Spectroscopic and Thermal Characterization of Extra Virgin Olive Oil Adulterated with Edible Oils.

The substitution of extra virgin olive oil with other edible oils is the primary method for fraud in the olive-oil industry. Developing inexpensive analytical methods for confirming the quality and authenticity of olive oils is a major strategy towards combatting food fraud. Current methods used to detect such adulterations require complicated time- and resource-intensive preparation steps. In this work, a comparative study incorporating Raman and infrared spectroscopies, photoluminescence, and thermal-conductivity measurements of different sets of adulterated olive oils is presented. The potential of each characterization technique to detect traces of adulteration in extra virgin olive oils is evaluated. Concentrations of adulterant on the order of 5% can be detected in the Raman, infrared, and photoluminescence spectra. Small changes in thermal conductivity were also found for varying amounts of adulterants. While each of these techniques may individually be unable to identify impurity adulterants, the combination of these techniques together provides a holistic approach to validate the purity and authenticity of olive oils.

Excitation and detection of acoustic phonons in nanoscale systems.

Phonons play a key role in the physical properties of materials, and have long been a topic of study in physics. While the effects of phonons had historically been considered to be a hindrance, modern research has shown that phonons can be exploited due to their ability to couple to other excitations and consequently affect the thermal, dielectric, and electronic properties of solid state systems, greatly motivating the engineering of phononic structures. Advances in nanofabrication have allowed for structuring and phonon confinement even down to the nanoscale, drastically changing material properties. Despite developments in fabricating such nanoscale devices, the proper manipulation and characterization of phonons continues to be challenging. However, a fundamental understanding of these processes could enable the realization of key applications in diverse fields such as topological phononics, information technologies, sensing, and quantum electrodynamics, especially when integrated with existing electronic and photonic devices. Here, we highlight seven of the available methods for the excitation and detection of acoustic phonons and vibrations in solid materials, as well as advantages, disadvantages, and additional considerations related to their application. We then provide perspectives towards open challenges in nanophononics and how the additional understanding granted by these techniques could serve to enable the next generation of phononic technological applications.

Structural color three-dimensional printing by shrinking photonic crystals.

The coloration of some butterflies, Pachyrhynchus weevils, and many chameleons are notable examples of natural organisms employing photonic crystals to produce colorful patterns. Despite advances in nanotechnology, we still lack the ability to print arbitrary colors and shapes in all three dimensions at this microscopic length scale. Here, we introduce a heat-shrinking method to produce 3D-printed photonic crystals with a 5x reduction in lattice constants, achieving sub-100-nm features with a full range of colors. With these lattice structures as 3D color volumetric elements, we printed 3D microscopic scale objects, including the first multi-color microscopic model of the Eiffel Tower measuring only 39 µm tall with a color pixel size of 1.45 µm. The technology to print 3D structures in color at the microscopic scale promises the direct patterning and integration of spectrally selective devices, such as photonic crystal-based color filters, onto free-form optical elements and curved surfaces.