Comparative analysis of the biomechanical behavior of the maxillary central incisors restored with glass fiber post and cast metal post and core submitted to orthodontic forces: A study with finite elements.

INTRODUCTION: Different types of intraradicular restorations and their insertion have an impact on teeth biomechanics. This study aimed to analyze the biomechanical behavior of maxillary central incisors restored with glass fiber post (GFP) and cast metal post and core (CMP) subjected to buccolingual and mesiodistal orthodontic forces using the finite element method. METHODS: Two models of the maxillary central incisor with periodontal ligament, cortical bone, and trabecular bone were made. One of the models included intraradicular restoration with GFP, whereas, in the other, the incisor was restored with CMP. After creating the tridimensional mesh of finite elements, applying 2 orthodontic forces were simulated: 65 g of buccolingual force and 70 g of mesiodistal force. The forces were applied parallel to the palatal plane in the region of the bracket slot, located 4 mm to the incisal edge. RESULTS: The maximum stresses generated in the GFP-restored root were 3.642 × 10-1 MPa and 4.755 × 10-1 MPa from the buccolingual and mesiodistal forces, respectively. Likewise, the stresses in the CMP restored root were 2.777 × 10-1MPa and 3.826 × 10-1MPa. The radicular area with higher stress on both models was located in the cervical third: on the buccal surface when the buccolingual force was applied and on the mesial surface when the mesiodistal force was applied. The highest stress levels were found on the CMP structure. CONCLUSIONS: The incisor restored with cast metal post revealed lower stress values transferred to the root than the one restored with GFP. The stresses on the structure of the GFP were lower and more homogeneous than the ones found on the cast metal post. The difference among the stress values in the materials is within a safe margin for using both materials in relation to orthodontic forces.

In Silico Mechanical Effort Analysis of the All-On-4 Design Performed With Platform-Switching Distal Short Dental Implants.

Short dental implants with platform matching connection have been used for the rehabilitation of atrophic jaws whenever standard-length dental implants cannot be placed without prior bone augmentation. Yet, there remains a lack of data regarding the risk of technical failures when the all-on-4 configuration is performed in atrophic jaws with platform-switching distal short dental implants. Thus, the current study used the finite element method to evaluate the mechanical behavior at the level of the prosthetic components of the all-on-4 concept performed in atrophic mandible using short-length distal implants with platform switching (PSW) connection. Three models of the all-on-4 configuration were generated in human atrophic mandibles. The geometric models consisted of PSW connection tilted standard (AO4T; θ = 30 deg; 11 mm-length), straight standard (AO4S; θ = 0 deg; 11 mm-length) and straight short (AO4Sh; θ = 0 deg; 8 mm-length) distal implants. A resultant force of 300 N was performed obliquely in the left side and posterior region of the prosthetic bar. The von Mises equivalent stress (σvm) and maximum and minimum principal stresses (σmax and σmin) were performed at level of the prosthetic components/implants and peri-implant bone crest, respectively. The general displacement of the models was also evaluated. The stress analysis was performed on the side of load application. The AO4S configuration showed the lowest values of σvm in the mesial left (ML) and distal left (DL) abutments (37.53 MPa and 232.77 MPa, respectively) and dental implants (91.53 MPa and 231.21 MPa, respectively). The AO4Sh configuration showed the highest values of σvm in the bar screw (102.36 MPa), abutment (117.56 MPa), and dental implant (293.73 MPa) of the ML area. Among the models, the highest values of σmax and σmin were noticed in the peri-implant bone crest of the AO4T design (131.48 MPa and 195.31 MPa, respectively). All models showed similar values of general displacements, which were concentrated in the mandible symphysis. The all-on-4 configurations designed with PSW connection and tilted standard (AO4T; θ = 30 deg; 11 mm-length), straight standard (AO4S; θ = 0 deg; 11 mm-length) or straight short (AO4Sh; θ = 0 deg; 8 mm-length) distal implants were not associated with higher odds of technical failures. The AO4Sh design may be a promising option for the prosthetic rehabilitation of atrophic jaws.

Mechanical stress distribution over the palate by different pacifiers assessed by finite element analysis and clinical data.

The mechanical behavior of each type of pacifier on rigid structures and their various impacts on orofacial growth have yet to be discovered. The study aimed to evaluate the stress distribution over a child's palate by three types of pacifiers using finite element analysis and clinical and laboratory data. Modulus of elasticity was obtained from 30 specimens comprising 10 of each conventional (A), orthodontic (B), and breast-shaped (C) pacifiers. Tongue strength was assessed in eight 3-year-old children (kPa). A hemi-maxilla model was obtained from 2- to 3-year-old skull tomography, and the images of pacifiers A, B, and C were captured using 3D scanning. The Hypermesh® program generated a mesh of 6-node tetrahedral elements for applying forces in the X, Y, and Z directions to enable a nonlinear analysis. Pacifier B exhibited the highest values for distributed stress on the palate, followed by pacifier A. Pacifier B stimulated the maxilla forward and sideways. In contrast, pacifier A promoted a forward and upward load, favoring a more atresic palate. Pacifiers A and B tended to rotate in the sagittal plane, generating tensions in the anterior incisors and favoring the open bite. Pacifier C exhibited lateral expansion by stress induction over the mid-palatal suture with less influence on incisor inclination. Pacifiers showed different detrimental stress distributions on the palate. This information can be helpful for improving recommendations given to parents.

Torqued and conventional cantilever for uprighting mesially impacted molars: A 3-dimensional finite element analysis.

INTRODUCTION: The objective of this study was to evaluate the effects of the torqued cantilever (TC) and conventional tip-back cantilever (CC) made of stainless steel (SS) and titanium-molybdenum alloy (TMA) on the uprighting of mesially impacted mandibular molars using three-dimensional finite element analysis. METHODS: The 3-dimensional mandibular model included part of the mandible with mesially tipped and impacted mandibular second molar, periodontal ligament (PDL), molar tube, mini-implant, and cantilevers. Four finite element method models (TC-SS, TC-TMA, CC-SS, and CC-TMA) were created to simulate different skeletally anchored uprighting mechanics. CC mechanics involved a known 0.019 × 0.025-in helical cantilever acting on a buccal molar tube. TC mechanics included a 0.019 × 0.025-in cantilever capable of producing mesial root torque by acting on a tube positioned on the molar disto-occlusal surface with the slot in a buccolingual direction. Three-dimensional molar displacement and stress distribution on the molar PDL were recorded. RESULTS: The SS cantilever produced almost twice as much molar displacement as the TMA. TC mechanics showed more evident mesial displacement of the molar root apexes. CC mechanics had greater molar rotation. TC uprighting moment produced greater molar mesial extrusion and greater intrusion of the distal root apex. The dual deflection system of the TC mechanics induced the lowest stress on the PDL, regardless of the metallic alloy. CONCLUSIONS: TC delivered a more efficient uprighting moment to the molar with less unwanted tooth movement and stress on the PDL and a more accessible site for bonding the molar tube.

Biomechanical Evaluation of Different Implant-Abutment Connections, Retention Systems, and Restorative Materials in the Implant-Supported Single Crowns Using 3D Finite Element Analysis.

This is an in silico study aimed to evaluate the biomechanical influence of different implant-abutment interfaces (external hexagon and Morse taper implants), retention systems (cement and screw retained), and restorative crowns (metal-ceramic and monolithic) using 3-dimensional finite element analysis (3D-FEA). Eight 3D models were simulated for the maxillary first molar area using InVesalius, Rhinoceros, and SolidWorks and processed using Femap and NEi Nastran software. Axial and oblique forces of 200 and 100 N, respectively, were applied on the occlusal surface of the prostheses. Microstrain and von Mises stress maps were used to evaluate the deformation (cortical bone tissue) and stress (implants/fixation screws/crowns), respectively, for each model. For both loadings, Morse taper implants had lower microstrain values than the external hexagon implants. The retention system did not affect microstrain on the cortical bone tissue under both loadings. However, the cemented prosthesis displayed higher stress with the fixation screw than the external hexagon implants. No difference was observed between the metal-ceramic and zirconia monolithic crowns in terms of microstrain and stress distribution on the cortical bone, implants, or components. Morse taper implants can be considered as a good alternative for dental implant rehabilitation because they demonstrated better biomechanical behavior for the bone and fixation screw as compared to external hexagon implants. Cement-retained prosthesis increased the stress on the fixation screw of the external hexagon implants, thereby increasing the risk of screw loosening/fracture in the posterior maxillary area. The use of metal-ceramic or monolithic crowns did not affect the biomechanical behavior of the evaluated structures.

Effect of Splinting of Tilted External Hexagon Implants on 3-Unit Implant-Supported Prostheses in the Posterior Maxilla: A 3D Finite Element Analysis.

PURPOSE: To assess the effects of tilted external hexagon implants and splinted restorations in terms of stress distribution on the bone tissue, implants, and prosthetic screws, using three-dimensional finite element analysis. MATERIALS AND METHODS: Six models were used to simulate a posterior maxilla bone block (type IV) from the first premolar to the first molar. Each model included three 4.1-mm-diameter external hexagon implants with varying inclinations (0°, 17°, and 30°) and crown designs (splinted and nonsplinted restorations). The forces applied were as follows: 400 N axially (50 N for each slope of the cusp) and 200 N obliquely (45° only on the buccal slope of the cusp). Stress distribution on the implants and prosthetic screw was evaluated using Von Mises stress, while the maximum principal stress was used to evaluate the stress distribution in the bone tissue. RESULTS: The oblique load increased the stress on all the structures in all the models. Increased inclination of the implants resulted in higher stress concentration in the bone tissue, implants, and prosthetic screws. However, splinted restorations contributed to reduction of the stress for the oblique loading, mainly in the bone tissue and prosthetic screw of the first molar, as the stress was shared between the first and second premolar restorations. CONCLUSIONS: Tilted implants increased proportionally the stress on bone tissue and prosthetic screws of models. Additionally, splinting restorations reduced the stress concentration area in the simulated bone tissue, implants, and prosthetic screws in the first molar, as the stress was shared with the adjacent implants.

A New Proposal for Calibrated Gauges for Removable Partial Dentures: A Finite Element Analysis.

AIM: The aim of this study was to evaluate the stress distribution of a planned removable partial denture (RPD) using new proposals for calibrated gauges of 0.3 mm and 0.35 mm undercuts through the three-dimensional (3D) finite element methodology, and compare them with 0.25 mm and 0.5 mm gauges that are already existing in clinical practice. MATERIALS AND METHODS: Kennedy class-I edentulous 3D models and their respective RPDs (InVesalius software; Rhinoceros and SolidWorks CAD) were created and exported to the finite element program HyperMesh 2019 for mesh configuration. In the following steps, axial loading (0º) of 40 N per point was performed, with 3 points on the molars and 2 points on the premolars, totaling 280 N unilaterally. The model was processed by the OptiStruct 2019 software and imported into the HyperView 2019 software to obtain the stress maps (MPa). RESULTS: The use of 0.30 and 0.35 mm calibrated gauges presented tensions similar to those with the 0.25 mm gauge (gold standard) and caused no significant damage to biological structures. The use of a 0.5 mm undercut caused greater traction force in the periodontal ligament of the abutments. CONCLUSIONS: The 0.35 mm undercut seems promising as it presented more favorable results in this simulation, on the other hand, a 0.5 mm undercut is greater than that necessary for retainers made of CoCr. CLINICAL SIGNIFICANCE: This study aims to measure a new undercut gauge (0.35 mm) to increase the retention area in abutment teeth of removable partial dentures.

Effect of bone quality and bone loss level around internal and external connection implants: A finite element analysis study.

STATEMENT OF PROBLEM: A consensus regarding the biomechanical effects of vertical bone loss in normal and osteoporotic bone tissue according to different implant-abutment interfaces is lacking. PURPOSE: The purpose of this finite element analysis study was to evaluate the effect of vertical bone loss (without bone loss; with 1.5-mm bone loss; with 3-mm bone loss; and with 4.5-mm bone loss) in normal and osteoporotic bone that received a Ø4×10-mm implant with different implant-abutment connections (external connection [external hexagon] and internal connection [Morse taper]) by using 3D finite element analysis. MATERIAL AND METHODS: Sixteen 3D models were simulated. Axial and oblique forces of 200 N and 100 N, respectively, were applied on the occlusal surfaces of the prostheses. Maximum principal stress and microstrain were determined from the bone tissue of each model. von Mises stress analysis was used to evaluate the stress distribution in implants and prosthetic components (fixation screws, abutment, and crown). RESULTS: The results showed higher stress concentrations in models with bone loss as increased vertical bone loss contributed to higher stress and microstrain in the bone tissue, regardless of the quality of bone and implant-abutment connection. Osteoporotic bone contributed to increase in microstrain in the trabecular bone. The internal connection showed lower stress than the external connection implants only in models without marginal bone loss. Furthermore, higher stress concentrations were observed in the implants and fixation screws in models with increased bone loss and external connection implants, mainly under oblique loading. Osteoporotic bone did not affect stress distribution in the implants and prosthetic components. CONCLUSIONS: Progressive bone loss contributed to higher stress in the bone tissue, implants, and prosthetic components. The osteoporotic bone affects only the microstrain in the trabecular bone, but not the stress in the implants and prosthetic components. The internal connection implants showed lower stress in the cortical bone only in models without bone loss, while external connection implants exhibited higher stress in the implants and screws under oblique loading.

Influence of the hyrax expander screw position on displacement and stress distribution in teeth: A study with finite elements.

INTRODUCTION: This study aimed to simulate the different positions of the hyrax appliance expander screw and evaluate tooth displacement and the stress distribution standard on the periodontal ligament using the finite element method. METHODS: Part of the maxilla with anchorage teeth, periodontal ligament, midpalatal suture, and the hyrax appliance was modeled, and finite element method models were created to simulate 6 different screw positions. There were 2 vertical positions at distances of 20 mm and 15 mm from the occlusal plane. Another position was anteroposterior, the center of the screw placed between and equidistant from the mesial face of the first molar and the distal face of the first premolar, aligned to the center of the crown of the first molar, with the anterior edge of the screw aligned to the distal face of the first molar. A 1 mm activation of the expander screw was simulated. The displacement (total, vertical, and buccolingual) and the stress distribution on the periodontal ligament of supporting teeth in each model were registered. RESULTS: The model simulating the expander screw in a more occlusal and anterior position presented higher displacement values and higher stress concentration, followed by the model with the screw in a more posterior but same vertical position. With the exception of the first premolar, the teeth presented cervical-apical displacement in the vestibular face and apical-cervical displacement in palatal faces. This displacement is compatible with the vestibular inclination associated with the activation of the expander screw. The first premolar presented an atypical tendency for the mesial and lingual displacement of the vestibular surface and counterclockwise rotation. CONCLUSIONS: The supporting teeth presented a tendency for vestibular crown displacement and lingual root displacement associated with compression areas in the vestibular-cervical region and tensile strength in the linguoapical region. Placing the expander screw in a more occlusal and anterior position generated more mechanical stress transfer, resulting in greater dental displacement.

An In Silico Model for the Prediction of Changes in Mineral Density in Cortical Bone Remodeling.

An in silico model for the estimation of volumetric bone mineral density (vBMD) changes at a cortical bone site subjected to mechanobiological bone remodeling is proposed in this manuscript. Mechanisms of cell differentiation, receptor-ligand binding, mechanical signaling, and resorption or deposition of bone matrix were considered, therefore providing a comprehensive description of mechanobiological bone remodeling in the bone microenvironment and enabling the analysis of temporal evolution of disease or therapy scenarios. The proposed model is composed by five modules, namely, bone cells populations, mechanobiology, volume fractions and porosity, mineral density, and structural stiffness. The model is an extension of other models found in the literature because equations for the obtaining of cortical vBMD and the binding of parathyroid hormone (PTH) to parathyroid hormone 1 receptor are included. The proposed model showed a satisfactory agreement with the solutions of other in silico models found in the literature. Simulations of walking and running exercise routines were performed for the evaluation of model capability regarding the control of the numerical error and prediction of vBMD. The computational method used to solve the case study controlled the relative numerical error by less than 1 × 10-7 for approximately 1.7 × 106 time steps. The predicted values correlate with the concept of increasing BMD by vigorous physical activity; however, they contrast with the specific effect of physical activities on cortical vBMD.

Influence of Different Implants on the Biomechanical Behavior of a Tooth-Implant Fixed Partial Dentures: A Three-Dimensional Finite Element Analysis.

This study analyzed the biomechanical behavior of rigid and nonrigid tooth-implant supported fixed partial dentures. Different implants were used to observe the load distribution over teeth, implants, and adjacent bone using three-dimensional finite element analysis. A simulation of tooth loss of the first and second right molars was created with an implant placed in the second right molar and a prepared tooth with simulated periodontal ligament (PDL) in the second right premolar. Configurations of two types of implants and their respective abutments-external hexagon (EX) and Morse taper (MT)-were transformed into a 3D format. Metal-ceramic fixed partial dentures were constructed with rigid and nonrigid connections. Mesh generation and data processing were performed on the 3D finite element analysis (FEA) results. Static loading of 50 N (premolar) and 100 N (implant) were applied. When an EX implant was used, with a rigid or nonrigid connection, there was intrusion of the tooth in the distal direction with flexion of the periodontal ligament. Tooth intrusion did not occur when the MT implant was used independent of a rigid or nonrigid connection. The rigid or nonrigid connection resulted in a higher incidence of compressive forces at the cortical bone as well as stress in the abutment/pontic area, regardless of whether EX or MT implants were used. MT implants have a superior biomechanical performance in tooth-implant supported fixed partial dentures. This prevents intrusion of the tooth independent of the connection. Both types of implants studied caused a greater tendency of compressive forces at the crestal area.

Influence of the hyrax expander screw position on stress distribution in the maxilla: A study with finite elements.

INTRODUCTION: Our objective was to evaluate the stress and deformation distribution patterns on the maxillary bone structure using the finite element method by simulation of different vertical and anteroposterior positions of the expansion screw on the hyrax expander appliance. METHODS: Part of the maxilla with anchorage teeth, midpalatal suture, and the hyrax appliance were modeled, and 6 distinct finite element method models were created to simulate different positions of the expansion screw. There were 2 vertical positions at distances of 20 and 15 mm from the occlusal plane. Another 3 positions were anteroposterior, with the center of the screw placed between and equidistant from the mesial face of the first molar and the distal face of the first premolar, aligned to the center of the crown of the first molar, and the anterior edge of the screw aligned to the distal face of the first molar. The initial activations of the expanders were simulated, and the stress distributions on the maxilla in each model were registered. RESULTS: The stress was concentrated in the anterior region of the models, close to the incisive foramen, dissipating through the palate in the posterior and lateral orientations, in the direction of the pterygoid pillar, diverting from the midpalatal suture region. When the expander screw was simulated closer to the occlusal plane and in a more anterior position, more stress was located around the incisive foramen and distributed through the midpalatal suture to its posterior portion. More posterior positions resulted in concentrated stress around the pterygoid pillars. At all simulations, the midpalatal suture showed a V-shaped expansion, with the vertex superior in the coronal view and posterior in the axial view. CONCLUSIONS: Different positions of the expander screw interfered with stress intensity and distribution patterns. When the expansion screw was simulated in a more occlusal and anterior position, it was more efficient to transfer the mechanical effects from the appliance to the bone structures.

Parafunctional loading and occlusal device on stress distribution around implants: A 3D finite element analysis.

STATEMENT OF PROBLEM: An occlusal device is frequently recommended for patients with bruxism to protect implant-supported restorations and prevent marginal bone loss. Scientific evidence to support this treatment is lacking. PURPOSE: The purpose of this 3-dimensional (3D) finite element study was to evaluate the influence of an acrylic resin occlusal device, implant length, and insertion depth on stress distribution with functional and parafunctional loadings. MATERIAL AND METHODS: Computer-aided design software was used to construct 8 models. The models were composed of a mandibular bone section including the second premolar and first and second molars. Insertion depths (bone level and 2 mm subcrestal) were simulated at the first molar. Three natural antagonist maxillary teeth and the placement or not of an occlusal device were simulated. Functional (200-N axial and 10-N oblique) and parafunctional (1000-N axial and 25-N oblique) forces were applied. Finite element analysis (FEA) was used to determine the maximum principal stress for the cortical and trabecular bone and von Mises for implant and prosthetic abutment. RESULTS: Stress concentration was observed at the abutment-implant and the implant-bone interfaces. Occlusal device placement changed the pattern of stress distribution and reduced stress levels from parafunctional loading in all structures, except in the trabecular bone. Implants with subcrestal insertion depths had reduced stress at the implant-abutment interface and cortical bone around the implant abutment, while the stress increased in the bone in contact with the implant. CONCLUSIONS: Parafunctional loading increased the stress levels in all structures when compared with functional loading. An occlusal device resulted in the lowest stress levels at the abutment and implant and the most favorable stress distribution between the cortical and trabecular bone. Under parafunctional loading, an occlusal device was more effective in reducing stress distribution for longer implants inserted at bone level. Subcrestally, implant insertion yielded the most favorable biomechanical conditions at the abutment-implant interface and at the coronal surface of the cortical bone, mainly when there was no occlusal device.

Finite Element Evaluation of Stable Fixation in Combined Mandibular Fractures.

PURPOSE: The fixation of combined mandibular fractures, especially symphyseal-condylar fractures, although occurring commonly and having a higher complication rate in the clinic, is rarely investigated regarding predictable therapeutic approaches. Thus this study's aim was to assess different forms of condylar fixation when combined with symphyseal fracture fixation. MATERIALS AND METHODS: Using finite element models, we analyzed the stress distribution that occurs when a condylar fracture is fixed with 1 miniplate, 2 miniplates, or a trapezoidal condylar miniplate and when a symphyseal fracture is fixed with 2 parallel plates, 2 perpendicular plates, or 2 lag screws. The null hypothesis was that there would be no differences among the different fixation techniques. RESULTS: The results showed a stress concentration in the anterior region of the condyle, close to the sigmoid notch. Moreover, adequate fixation in the symphysis could result in less tension at the condylar region. Therefore, when the symphysis was fixed with a lag-screw technique, condylar fixation was less required, showing a more adequate stress distribution when the condyle was fixed with 1 or 2 plates. Conversely, when the symphyseal fixation was less effective, by use of perpendicular plates, there was a change in the stress distribution at the condylar region, altering fixation behavior and resulting in more tension and displacement in the condyle, especially when a trapezoidal plate was used. CONCLUSIONS: A lag screw and parallel double plates appear to be suitable for symphyseal fixation, whereas 2 straightly positioned plates and a trapezoidal plate are suitable for condylar fixation. However, the combination of perpendicular plates in symphyseal fixation and a trapezoidal plate in condylar fixation showed an altered stress distribution.

Short fibre-reinforced composite for extensive direct restorations: a laboratory and computational assessment.

OBJECTIVES: The objective of the study was to evaluate the effectiveness of a short fibre-reinforced composite (FRC) applied in combination with a conventional filler composite (CFC) on the fatigue resistance, fracture strength, failure mode and stress distribution, for restorations of premolars under two loading angles. MATERIAL AND METHODS: Thirty-two inferior premolars received extensive cavities with removal of the lingual cusp. Teeth were restored directly using 'FRC (EverX Posterior, GC) + CFC (G-aenial, GC)' or 'CFC only' and received two fatigue/fracture loadings at two different angles (0°/45°) (n = 8). Data were submitted to two-way ANOVA (α = 5 %) and Tukey test. Failure mode was analysed using SEM. Four 3D finite element (FE) models were constructed and static, linear and elastic analyses were performed. Maximum principal and von Mises stresses were evaluated. RESULTS: All specimens survived the mechanical fatigue simulation. No statistical difference in fracture resistance was recorded between FRC + CFC and CFC only, considering both loading angles (p = 0.115). However, the 0° loading showed a statistical significant higher strength than the 45° loading (p = 0.000). Failure mode analysis revealed more repairable fractures upon 0° loading, versus more root fractures (unrepairable) upon 45° loading. FE revealed a higher amount of stress upon 45° loading, with tensile stress being imposed to the lingual cervical area. CONCLUSION: The fracture strength was not increased using the FRC. Loading at a 45° decreased significantly the fracture resistance. CLINICAL RELEVANCE: The restoration of extensive cavities in posterior tooth is a challenge for the clinicians and the choice of the material that increases the fracture strength of tooth-restoration complex is required.

A three-dimensional finite element analysis of the sports mouthguard.

BACKGROUND/AIM: The aim of this study was to evaluate the compressive and tensile stresses on dentin and enamel in five different situations: no mouthguard and mouthguards from 1 mm thickness up to 4 mm thickness, using finite element analysis. MATERIALS AND METHODS: A three-dimensional geometry of an upper right central incisor was obtained from a computed tomography and transformed into a mesh separating enamel from dentin. A mouthguard was created covering the buccal surface of the enamel in different thicknesses, and a rubber ball with a velocity of 5 m s(-1) was made as the impact object. RESULTS: The maximum principal stress and the minimal principal stress were evaluated in all situations on dentin and enamel. Both maximum and minimal stress on enamel had the greatest value on the control situation (no mouthguard), and their value decreased as the mouthguard thickness increased. The reduction ranged from 66.62% to 85.5% for compressive stress and from 9.76% to 33.37% for tensile stress on enamel. The results for dentin were similar among the situations with or without mouthguards. CONCLUSION: The mouthguard had beneficial effect considering the stresses on enamel, and between the mouthguard thickness of 3 and 4 mm, there was minimum difference.

Bridging Plate Development for Treatment of Segmental Bone Defects of the Canine Mandible: Mechanical Tests and Finite Element Method.

With regard to the canine mandible, a mistaken concept of application is to assume that systemic plate-bone resistance is provided by the implant so that biomechanical position could be ignored. Because the alveolar border of the mandible is a tensile zone, the plate would ideally be positioned near this area while avoiding important structures. The aim of this study was to develop 2 bridging plates for the treatment of a segmental bone defect of the canine mandible using monocortical screws to avoid damage to the tooth roots and remaining neurovascular structures. Computed tomography images of the heads of 4 dogs (rottweiler, Doberman, boxer, and miniature poodle breeds) were used as models to develop the project. The images were reconstructed in 3-dimensional (3D) format. For each dog breed, 6 mandible prototypes were produced, each with a segmental bone defect in the right mandible. The mandibular reconstruction was performed with pure titanium bridging plate and locking screws. One plate model was developed for medium- and large-breed dogs and another for small-breed dogs. Mechanical testing showed the platemandible system resists the bite forces in all dog breeds. All safety factors were greater than I in the platemandible system for medium- and large-breed dogs and greater than 10 in the plate-mandible system for small-breed dogs. Thus, bridging plates designed with differentiated geometry and monocortical locking screws showed mechanical resistance to support simulated induced bone model defects and were able to support at least 5 times the value of bite force for each evaluated dog.

Comparison of Neck Screw and Conventional Fixation Techniques in Mandibular Condyle Fractures Using 3-Dimensional Finite Element Analysis.

PURPOSE: To compare the mechanical stress on the mandibular condyle after the reduction and fixation of mandibular condylar fractures using the neck screw and 2 other conventional techniques according to 3-dimensional finite element analysis. MATERIALS AND METHODS: A 3-dimensional finite element model of a mandible was created and graphically simulated on a computer screen. The model was fixed with 3 different techniques: a 2.0-mm plate with 4 screws, 2 plates (1 1.5-mm plate and 1 2.0-mm plate) with 4 screws, and a neck screw. Loads were applied that simulated muscular action, with restrictions of the upper movements of the mandible, differentiation of the cortical and medullary bone, and the virtual "folds" of the plates and screws so that they could adjust to the condylar surface. Afterward, the data were exported for graphic visualization of the results and quantitative analysis was performed. RESULTS: The 2-plate technique exhibited better stability in regard to displacement of fractures, deformity of the synthesis materials, and minimum and maximum tension values. The results with the neck screw were satisfactory and were similar to those found when a miniplate was used. CONCLUSION: Although the study shows that 2 isolated plates yielded better results compared with the other groups using other fixation systems and methods, the neck screw could be an option for condylar fracture reduction.

Three-Dimensional Finite Element Analysis of Anterior Single Implant-Supported Prostheses with Different Bone Anchorages.

The aim of this study was to evaluate the stress distribution of monocortical and bicortical implant placement of external hexagon connection in the anterior region of the maxilla by 3D finite element analysis (FEA). 3D models were simulated to represent a bone block of anterior region of the maxilla containing an implant (4.0 × 10.0 mm) and an implant-supported cemented metalloceramic crown of the central incisor. Different techniques were tested (monocortical, bicortical, and bicortical associated with nasal floor elevation). FEA was performed in FEMAP/NeiNastran software using loads of 178 N at 0°, 30°, and 60° in relation to implant long axis. The von Mises, maximum principal stress, and displacement maps were plotted for evaluation. Similar stress patterns were observed for all models. Oblique loads increased the stress concentration on fixation screws and in the cervical area of the implants and bone around them. Bicortical technique showed less movement tendency in the implant and its components. Cortical bone of apical region showed increase of stress concentration for bicortical techniques. Within the limitations of this study, oblique loading increased the stress concentrations for all techniques. Moreover, bicortical techniques showed the best biomechanical behavior compared with monocortical technique in the anterior maxillary area.

Finite element analysis of bone stress after SARPE.

PURPOSE: This study investigated stress distribution in maxillas that underwent surgically assisted palatal expansion (SARPE). MATERIALS AND METHODS: Five maxillary models were built: no osteotomy (M1), Le Fort I osteotomy with a step in the zygomaticomaxillary buttress (M2), Le Fort I osteotomy with a step in the zygomaticomaxillary buttress and the pterygomaxillary disjunction (M3), Le Fort I osteotomy without a step (M4), and Le Fort I osteotomy with pterygomaxillary disjunction and no step (M5). Displacement coherence and maximum stress (MS) analyses were used for all models. RESULTS: Areas of tension spread to the maxilla and the region between the alveolar ridge and the palate and a critical point in the median suture for M2, M3, M4, and M5. In M2 and M4, MS spread farther toward and over the pterygoid process, contrary to what was found in M3 and M5. M3 had a better performance than the other models, and the tensile stress was interrupted by the posterior osteotomy, thus avoiding possible damage to the sphenoid bone or difficulties in expanding the posterior region of the maxilla. CONCLUSIONS: The steps in the zygomaticomaxillary buttress and the pterygomaxillary disjunction seem to be important to decrease the harmful dissipation of tensions during SARPE.