Effects of design software program and manufacturing method on the marginal and internal adaptation of esthetic crowns for primary teeth: A microcomputed tomography evaluation.

STATEMENT OF PROBLEM: The adaptation of digitally produced crowns is affected by the design software program and manufacturing method. The effect of artificial intelligence (AI) software program design on the adaptation of the crowns is unclear and comparative evaluations should be documented. PURPOSE: The purpose of this study was to assess the marginal and internal gaps, the absolute marginal discrepancies, and the 3-dimensional (3D) discrepancy volumes of the resin-based milled and 3D printed crowns for primary teeth designed with computer-aided design (CAD) and AI software programs by using microcomputed tomography (µCT). MATERIAL AND METHODS: A total of 40 resin-based esthetic crowns were produced for a prepared typodont tooth (right mandibular primary second molar) according to the design software program (CAD and AI) and manufacturing method (milling and 3D printing) (n=10). Four experimental groups were generated as CAD-milled, CAD-3D printed, AI-milled, and AI-3D printed. The marginal, axial, and occlusal gap values, the absolute marginal discrepancies, and the 3D discrepancy volumes of the specimens were measured by using µCT. The data were analyzed by using 2-way ANOVA and the Tukey HSD tests (α=.05). RESULTS: The lowest value for the marginal gap (54 ±43 µm) was observed in the CAD-milled group and the marginal gap value of the AI-3D printed group was significantly lower than the AI-milled group (P<.05). The lowest value for the axial gap (63 ±7 µm) was observed in the AI-3D printed group, and the highest value (145 ±58 µm) was observed in the CAD-milled group; the result for the occlusal gap value was opposite. The highest absolute marginal discrepancy value was observed in the CAD-milled group. The 3D discrepancy volumes increased in the order of the CAD-3D printed, AI-milled, CAD-milled, and AI-3D printed groups. CONCLUSIONS: The marginal and internal gap values of the resin-based crowns were affected by the design software program and manufacturing method; however, tested groups showed clinically acceptable gap values.

Evaluation of the relationship between periodontal bone destruction and mesial root concavity of the maxillary first premolar.

BACKGROUND: The purpose of this study was to investigate the morphology of maxillary first premolar mesial root concavity and to analyse its relation to periodontal bone loss (BL) using cone beam computed tomography (CBCT) and panoramic radiographs. METHODS: The mesial root concavity of maxillary premolar teeth was analysed via CBCT. The sex and age of the patients, starting position and depth of the root concavity, apicocoronal length of the concavity on the crown or root starting from the cementoenamel junction (CEJ), total apicocoronal length of the concavity, amount of bone loss both in CBCT images and panoramic radiographs, location of the furcation, length of the buccal and palatinal roots, and buccopalatinal cervical root width were measured. RESULTS: A total of 610 patients' CBCT images were examined, and 100 were included in the study. The total number of upper premolar teeth was 200. The patients were aged between 18 and 65 years, with a mean age of 45.21 ± 13.13 years. All the teeth in the study presented mesial root concavity (100%, n = 200). The starting point of concavity was mostly on the cervical third of the root (58.5%). The mean depth and buccolingual length measurements were 0.96 mm and 4.32 mm, respectively. Depth was significantly related to the amount of alveolar bone loss (F = 5.834, p = 0.001). The highest average concavity depth was 1.29 mm in the group with 50% bone loss. The data indicated a significant relationship between the location of the furcation and bone loss (X2 = 25.215, p = 0.003). Bone loss exceeded 50% in 100% of patients in whom the furcation was in the cervical third and in only 9.5% of patients in whom the furcation was in the apical third (p = 0.003). CONCLUSIONS: According to the results of this study, the depth of the mesial root concavity and the coronal position of the furcation may increase the amount of alveolar bone loss. Clinicians should be aware of these anatomical factors to ensure accurate treatment planning and successful patient management.

The micro CT evaluation of crown and root pulp volume versus dentin thickness in teeth in postmortem interval (PMI).

Determining the postmortem interval (PMI) is one of the main study subjects of forensic sciences. The main purpose of this prospective in vitro study that was the Micro-CT evaluation of teeth crown and root pulp volume versus dentin thickness in terms of PMI determination. The study involved 60 female Wistar rats, with weights ranging from 270 to 320 g. These rats were grouped into six different post-mortem period categories. Following the animals' sacrifice, they were subjected to a natural putrefaction period, with a control group, in the grounds of a sheltered garden. Hemi-mandible samples were then extracted and placed in glass tubes for Micro-CT evaluations, following the progression of putrefaction processes. The pulp volume and dentin thickness were assessed using Micro-CT, and the gathered data underwent statistical analysis. Micro-CT was employed to analyze sixty right mandibular second molar teeth in the hemi-mandible. The crown pulp volume exhibited a reduction in group 6, with a value of 0.239 mm3 after a three-month period of natural putrefaction (p < 0.001). There is statistically differences among groups in case of pairwise comparison (p < 0.05). However, the root pulp volume and dentin thickness variables did not display any statistically significant changes. Despite certain limitations associated with this study, the Micro-CT findings concerning teeth pulp volume can serve as an objective parameter, especially for late postmortem investigations and the estimation of time of death.

Resveratrol prevents ovariectomy-induced bone quality deterioration by improving the microarchitectural and biophysicochemical properties of bone.

INTRODUCTION: Osteoporosis is a major health problem that is very common worldwide and is characterized by both low bone density and deterioration in bone quality. New treatment options without side effects have become an active area of research in recent years. This study was designed to investigate the preventive effects of resveratrol on bone quality deterioration caused by ovariectomy. MATERIALS AND METHODS: Sixty rats were randomly divided into five groups (12 animals per group): Control, Sham-operated (SHAM), ovariectomized (OVX), OVX + Resveratrol-40 mg/kg/day (OVX + Res40), OVX + Resveratrol-80 mg/kg/day (OVX + Res80). Resveratrol was administered by oral gavage (40 and 80 mg/kg/day) for ten weeks. Micro-CT measurements, biomechanical testing, Raman spectroscopy analysis, and RT-PCR analysis were performed. ALP, OCN, TAS, and TOS levels were also measured from blood serum. RESULTS: Bone strength, bone volume/total volume, trabecular volume, and trabecular thickness were higher in the OVX + RES-80 group than in the OVX group. Resveratrol increased osteogenic differentiation, as the expression of osteogenic markers ALP, Col1A1, Runx2, OPG, OCN increased in both OVX + RES-80 and OVX + RES-40 groups compared to the OVX group. 80 mg/kg/day resveratrol administration decreased the levels of ALP, OCN and TOS in ovariectomized rats. Raman spectroscopy findings showed a preventive effect of resveratrol administration against ovariectomy-induced deterioration in biophysiochemical properties of bone tissue. CONCLUSION: This study revealed that administration of different doses of 80 mg/kg/day and 40 mg/kg/day of resveratrol had protective effects on bone quality deterioration caused by ovariectomy.

Examination of sinus tympani, subtympanic sinus, and facial sinus with MicroCT.

This study aimed to determine sinus tympani, subtympanic sinus (STS), facial sinus (FS) morphologies, and type distributions. Type distributions were based on their relations with the facial nerve (FN). A total of 20 right and 20 left temporal dry bones without physical deformation were scanned with a MicroCT device. All measurements were made using MicroCT programs from sections in the axial plane. For the FS, the average depth was measured as 3.485 mm without any classification, and 29 of the 40 bones had Type C radiological morphology. The mean depth for all sinus tympanicus was 2.646 mm, and 22 of the 40 bones had Type B morphology. For the STS, 29 out of 40 samples had no contact with the FN; regardless of the classification, the average depth was measured as 2.376 mm. We reveal the depths of the tympanic cavities and their relationship with the FN. The results of this study may benefit clinicians performing retrotympanum surgeries.

Effect of different preparation finishing procedures on the marginal and internal fit of CAD-CAM-produced restorations: A microcomputed tomography evaluation.

STATEMENT OF PROBLEM: Accurate fit is an important factor for the longevity of computer-aided design and computer-aided manufacturing (CAD-CAM) ceramic restorations. Few studies have compared how restoration finishing procedures affect the marginal and internal fit of these restorations by using microcomputed tomography (µCT). PURPOSE: The purpose of this in vitro study was to evaluate the preparations with different surface finishing procedures for the fit of CAD-CAM restorations by using µCT. MATERIAL AND METHODS: A total of 28 anatomic contour monolithic feldspathic ceramic crowns were produced for 4 typodont teeth prepared according to the different surface finishing procedures (n=7). The generated experimental groups were finishing with extra-coarse (181 µm) diamond rotary instruments (EC), finishing with fine (40 µm) diamond rotary instruments after extra-coarse diamond rotary instruments (F), finishing with very fine (20 µm) diamond rotary instruments after extra-coarse and fine diamond rotary instruments (VF), and finishing with extra-coarse, fine, and very fine diamond rotary instruments followed by polishing rubber points (P). µCT scans were obtained to measure the gaps between the typodont teeth and the crowns. Reference points such as the margin, chamfer (the deepest point), cusp tips, and central fossa were determined, and 196 measurements were made. Data were analyzed by using 2-way analyses of variance and the Tukey HSD test (α=.05). RESULTS: The highest gap values in all sections were observed in the finishing with extra-coarse (181 µm) diamond rotary instruments group. The lowest gap value in the marginal point was observed in the P group (P<.05). In total, the gap values of the reference points were in the order of margin, chamfer, cusp, and central fossa. CONCLUSIONS: µCT evaluation showed that tooth preparation finishing procedure with finer grit rotary instruments yielded better marginal fit for monolithic feldspathic CAD-CAM restorations. The internal gap values of all groups were also in the range of clinically acceptable values, important for mechanical properties.

Comparison of three different biomaterials used in in vitro molar apexification models.

OBJECTIVES: New biomaterials had some advantages such as mixing and easier application as compared to traditional MTA in single step apexification method. This study aimed to compare the three biomaterials used in the apexification treatment of immature molar teeth in terms of the time spent, the quality of the canal filling and the number of x-rays taken to complete the process. METHODS: The root canals of the extracted thirty molar teeth were shaped with rotary tools. To obtain the apexification model, ProTaper F3 was used retrograde. The teeth were randomly assigned into three groups based on the material used to seal the apex; Group 1: Pro Root MTA, Group 2: MTA Flow, Group 3: Biodentine. The amounts of the filling, the number of radiographs taken until treatment completion and the treatment duration were recorded. Then teeth were fixed for micro computed tomography imaging for quality evaluation of canal filling. RESULTS: Biodentine was superior to the other filling materials according to time. MTA Flow provided greater filling volume than the other filling materials in the rank comparison for the mesiobuccal canals. MTA Flow had greater filling volume than ProRoot MTA in the palatinal/distal canals(p = 0.039). Biodentine had greater filling volume more than MTA Flow in the mesiolingual/distobuccal canals (p = 0.049). CONCLUSIONS: MTA Flow was found as a suitable biomaterial according to the treatment time and quality of root canal fillings.

Can locally applied risedronate be an effective agent when combined with xenografts? An animal study.

BACKGROUND: To examine the effects of local risedronate application with xenografts on healing of rabbit skull defects using histological, histomorphometric, immunohistochemical, and three-dimensional radiological methods. METHODS: Two critical-sized defects with a diameter of 10 mm were created in 16 rabbits and filled with xenogenic bone graft and xenogenic bone graft + 5 mg risedronate in the control I and risedronate (RIS) groups, respectively. Residual graft, new bone, soft tissue areas, and bone volume were evaluated in the 4- and 8-week study groups. RESULTS: In both the 4- and 8-week samples, the RIS group samples had significantly higher mean new bone area values than the C group (p < 0.05). In both groups, the values for the new bone area were significantly higher in the 8-week-old samples than in the 4-week-old samples (p < 0.05). The h scores obtained for sialoprotein and osteopontin did not differ significantly between the groups at either time point (p > 0.05). The results of radiological evaluation showed that the bone density value was significantly higher in the C group than in the RIS group at either time point (p < 0.05). CONCLUSIONS: Although this study aimed to demonstrate the effect of risedronate on the osteoconductive properties of xenografts when applied locally, targeted results could not be achieved.

Investigation of taurine and aqueous garlic extract diet supplementation effect on the healing of rat osteoporotic fractures.

BACKGROUND: We have evaluated the effects of taurine and aqueous garlic extract (AGE) as a dietary supplement on osteoporotic fracture (OPF) healing in the ovariectomized rat femur fracture model. METHODS: In this experimental animal study,twenty-four osteoporosis-remodeled female Wistar albino rats were randomly divided into 3 groups (n: 8) according to their supplemented diet; control, taurine, and AGE groups. Unilateral femur middiaphysis mini-open osteotomy was stabilized with Kirschner wires. Six weeks after osteotomy, the rats were sacrificed before the femurs were harvested and OPF healing was evaluated with biochemical, histologic, microcomputed-tomography, and scintigraphic methods. RESULTS: As an indicator of the antiosteoporotic effect, the calcium levels of the taurine group were significantly lower than the AGE and control groups in biochemical analyzes (p < 0.01). In histological studies, the new bone diameter and new bone volume values of the taurine group were significantly higher than the control group (p = 0.002 and p = 0.032, respectively), while higher trabecular-compact callus was observed in the taurine and AGE groups, respectively, compared to the control group. In morphological analyses, taurine and AGE groups had significantly higher bone volume/tissue volume, trabecular number, bone surface density, and lower trabecular separation than the control group (p < 0.05). The scintigraphic imaging showed a significant increase in osteoblastic activity of the taurine group compared to the control group (p = 0.005). DISCUSSION: Taurine and AGE have positive anabolic effects, respectively, on the healing of OPFs, demonstrated by biochemical, histological, morphological, and scintigraphic methods.

Micro-CT evaluation of the effect of various ScRp instrumentation methods on cement loss, porosity and micro-crack formation.

OBJECTIVES: The purpose of this study was to compare the effectiveness of three different instruments on cement loss, porosity and micro-crack formation, which was not evaluated before, following scaling and root planning (SRP) using micro-computed tomography (micro-CT). METHODS: In this experimental study, 30 single-rooted extracted human teeth were used and divided into three groups. All the teeth were scanned with micro-CT before and after SRP. Group 1: SRP was performed with Gracey curettes, Group 2: SRP was performed by using an ultrasonic device, and Group 3: SRP was performed by using diamond burs. Cement loss from the root surface, porosity, and micro-crack formation in the root dentine were analysed. Micro-CT is used for qualitative and quantitative analysis of samples. The obtained data were analysed statistically (p < 0.05). RESULTS: Minimum cement loss following SRP was detected with ultrasonic scaler (26.98 mm3 ), whereas the highest was created by diamond burs (96.20 mm3 ) (p < 0.05). The total porosity values after SRP were 0.278%, 0.334% and 0.252% for Groups 1, 2 and 3, respectively. Although Group 3 had the least porosity values, there was no statistically significant difference between the groups. The highest micro-crack formation was seen in Group 2 and the lowest was in Group 1 with a significant difference (p < 0.05). CONCLUSIONS: More cement loss was observed with diamond burs. Ultrasonic devices appear to be a viable alternative to instrumentation with curettes. However, ultrasonic devices should be used carefully because of micro-crack formation since the micro-crack resulting from instrumentation with hand instruments is the least of all.

Micro-ct findings of concentrated growth factors (cgf) on bone healing in masquelet's technique-an experimental study in rabbits.

INTRODUCTION: A recent histopathological and immunohistochemical study has proved that the addition of concentrated growth factors (CGF) to the Masquelet's technique contributes to the quality of the membrane formed, in respect of inducing inflammation and proliferation, maintaining vascularization on large diaphyseal bone defects, and increasing the number of stem cells. The aim of the study is comparison of radiological results of this combination treatment by micro-CT. MATERIALS AND METHODS: The study was planned on a critical bone defect model in rabbit radius. Group I and Group III were the control groups to which only the Masquelet's technique is applied. Group II and Group IV were CGF groups in addition to the Masquelet's technique. CGF was prepared by centrifugation of rabbit's own blood. For early phase, Groups I and II were evaluated in the 8th week, while for late phase, Group III and Group IV were evaluated in the 12th week. Groups were compared in terms of bony union radiologically by micro-CT(µCT) (New Bone Volume (NBV), Total Bone Volume (TBV) and NBV/TBV) and histopathologically. RESULTS: The structural parameters, including NBV, TBV, NBV/TBV were higher in the early- (8th week) and late-phase (12th week) CGF group. There was no statistically significant difference between CGF and control groups in early phase, (p = 0.153), while in late phase, CGF group was significantly higher of new bone volume than the control group, 246.3 mm3 (196.1-258) and 169.6 mm3 (154.3-235.9), respectively (p = 0.028). For early phase, control group was significantly lower than late-phase control group, 121.8 mm3 (88.8-144.4) and 169.6 mm3 (154.3-235.9), respectively (p = 0.006). The ratio of New Bone Volume to Total Bone Volume (NBV/TBV ratio) in CGF groups was significantly higher compared to the control groups 27.3% (24.7-29.6), 35.3% (32.1-38.6) (p = 0.032) and 39.7% (36.7-41.6), 55.3% (52-57.5) (p = 0.002), respectively. Histopathologically, Microscopic New Bone Formation had no statistically significant difference between control and CGF groups in early phase (8th week) (p = 0.153), while in late phase (12th week), CGF group had significantly higher amount of new bone formation than the control group, 0.29 µm2 (0.27-0.36), 0.51 µm2 (0.42-0.59), respectively (p = 0.008). CONCLUSION: The addition of CGF to the Masquelet's technique is an important method for supporting new bone formation in large diaphyseal bone defects. LEVEL EVIDENCE: Level III, therapeutic/care management.

Investigation of the effect of ghrelin on bone fracture healing in rats.

Ghrelin is known to have effects on proliferation and differentiation of osteoblasts and improvement of bone mineral density in rats. However, no experimental research on ghrelin's effects on fracture healing has been reported. In this context, the effect of ghrelin on the union of femoral shaft fractures was examined in this study by evaluating whether ghrelin will directly contribute to fracture healing. Forty male Wistar-Albino rats were divided into two groups as control and experimental (ghrelin treated) and standard closed shaft fractures were created in the left femurs of all rats. Daily ghrelin injections were applied to the experimental groups and equal numbers of rats were killed after 14 and 28 days following fracture formation. Tissue samples were examined with radiological, biomechanical, biochemical and histological analyses. Densitometry study showed that bone mineral density was improved after 28 days of ghrelin treatment compared to control. On histological examination, at the end of the 14 and 28 days of recovery, significant union was observed in the ghrelin-treated group. The ghrelin-treated group had higher breaking strength and stiffness at the end of 28 days of recovery. Biochemically, ALP levels were found to be higher in the ghrelin-treated group at the end of 28 days of recovery. Results showed that ghrelin directly contributes to fracture healing and it is promising to consider the effect of ghrelin on fracture healing in human studies with pharmacological applications.

Can the Combination of Simvastatin and Melatonin Create a Synergistic Effect on Bone Regeneration?

PURPOSE: The present study evaluated the potential bone regeneration capacity of combining melatonin and simvastatin, with a goal of producing more osteogenic bone substitutes. MATERIALS AND METHODS: A total of 48 male Wistar rats were randomly divided into 4 groups. The following were administered into critical-sized calvarial defects of the rats: Group I-human allograft; Group II-human allograft + 10 mg melatonin; Group III-human allograft + 0.1 mg simvastatin; and Group IV-human allograft + 10 mg melatonin + 0.1 mg simvastatin. Histopathologic, histomorphometric, and microcomputed tomographic evaluations were performed postprocedurally at 4 and 8 weeks. A P value < .05 was considered significant for all evaluations. RESULTS: Groups II and III had significantly superior regeneration compared to Group I at weeks 4 and 8. Group III had significantly superior regeneration compared to Group II, particularly in week 4. Group IV had significantly superior regeneration compared to all groups at week 8. CONCLUSIONS: The local administration of melatonin and simvastatin resulted in increased new bone mass and quality of bone microstructure than was seen in the control group. Simvastatin shortened the defect regeneration time more effectively than melatonin did. The combined use of melatonin and simvastatin provided a synergic effect on bone regeneration, particularly in the late phase of healing.

Marginal and internal fit of feldspathic ceramic CAD/CAM crowns fabricated via different extraoral digitization methods: a micro-computed tomography analysis.

The aim of this study was to compare the fit of feldspathic ceramic crowns fabricated via 3 different extraoral digitizing methods. Twelve maxillary first premolars were prepared and 36 single crowns were fabricated via 3 extraoral digitizing methods using a laboratory scanner (n = 12): (1) scanning the typodont (ST [control] group); (2) scanning the impression (SI group); (3) scanning the stone cast (SC group). Micro-computed tomography was used to calculate two-dimensional marginal-internal gap and the three-dimensional volumetric gap between the crowns and their corresponding dies. The measured gaps were divided into 6 location categories as follows: marginal gap (MG), finish line gap (FLG), axial wall gap (AWG), cuspal gap (CG), proximal transition gap (PTG), and central fossa gap (CFG). The correlation between each of the 3 extraoral digitizing methods and the adaptation status of the crown margins were also evaluated. The Wilcoxon signed-rank test, Spearman's rank test, and Chi-square test were used for data analysis (α = 0.05). The marginal gaps in the ST, SI, and SC groups differed significantly (24, 198 and 117.6 µm, respectively) (p < 0.05). Significant differences were found between the groups with regard to internal gap measurements, with SI representing higher gap measurements at FLG, PTG and CFG locations (p < 0.05). 3D volumetric gap measurements did not differ significantly (p > 0.05). Under-extended margins observed in the SI and SC groups were correlated with the digitizing method (Cramer's V-square: 0.14). When performing extraoral digitalization, clinicians should choose to scan the stone cast as scanning the stone cast resulted in better internal and marginal fit compared to scanning the impression.

Evaluation of Denture Base Adaptation Fabricated Using Conventional, Subtractive, and Additive Technologies: A Volumetric Micro-Computed Tomography Analysis.

PURPOSE: An in vitro study to compare the adaptation of denture bases fabricated with 4 different techniques using volumetric 3-dimentional (3D) analysis. MATERIAL AND METHODS: Edentulous maxillary and mandibular casts were scanned, and standardized denture bases were designed using CAD design software. The same standard tessellation language (STL) data were used to produce the denture bases with 4 different fabrication methods: compression molding (CM), injection molding (IM), PMMA milling (PM), and 3D printing (3D) (n = 11/group). Milled wax denture bases were used to fabricate CM and IM groups. Denture bases placed on edentulous casts were scanned using micro-computed tomography (micro-CT). Volumetric gap between denture base and cast was calculated from 6 locations for maxilla (anterior ridge crest, posterior ridge crest, labial vestibule, buccal vestibule, palate, and posterior palatal seal) and 3 locations for mandible (intermolar, molar, and retromolar) in addition to overall gap measurements for edentulous arches. The data were analyzed with factorial analysis of variance (ANOVA), 1-way ANOVA, and post-hoc Duncan tests. Reproducibility of fabrication methods with regard to each location was assessed using Z test (α = 0.05). RESULTS: In the maxilla, the highest and lowest palatal gap measurements were recorded for CM (898.44 ± 87.73 mm3 ) and PM (357.16 ± 57.68 mm3 ) (p = 0.05). The highest gap measurements for CM and 3D were at palate and, for IM and PM were at posterior ridge crest. In mandible, the volumetric gap measurements for CM were the highest and for PM were the lowest irrespective of location (p = 0.05). PM group showed the best reproducibility and adaptation with the lowest overall mean gaps for both edentulous arches (p = 0.05). CONCLUSIONS: Denture bases milled from PMMA blocks showed better adaptation than 3D printed, or wax milled and conventionally fabricated denture bases for both maxillary and mandibular arches. PMMA milling is a reproducible technique that enables the construction of accurate dentures. Clinicians should be cautious about the palatal gap when the compression molding technique is used. Micro-CT is a valid technique for evaluating the denture base adaptation.

Evaluation of the effects of locally applied rosuvastatin on bone formation in a three-dimensional reconstruction rabbit xenograft model

Background/aim: Guided bone regeneration (GBR) is commonly performed to repair bone defects, and rigid occlusive titanium barriers play a vital role in bone formation in regions with no prior bone tissue. The statin, rosuvastatin (RSV), strongly affects bone apposition when applied locally. Here, we aimed to evaluate the anabolic effects of locally applied RSV with a xenograft placed on rabbit calvaria. Materials and methods: Two rigid occlusive titanium caps were used in 16 rabbits after decorticating the calvarial bone. In the control group, the area under the cap was filled with a xenograft, while in the RSV group, a xenograft in combination with RSV (1 mg) was used. In both groups, at 6 and 12 weeks, new bone, residual graft, soft tissue areas, and histological and radiological bone volume were evaluated. Results: At 12 weeks, histologically, the RSV group exhibited superior new bone proportion values, and radiologically, new bone and total bone volume in the RSV group were significantly higher than in the control group (p < 0.05); there were no significant differences at 6 weeks (p > 0.05). Conclusion: According to our results, RSV applied locally under a titanium barrier on an area to be repaired with bone grafts increases new bone and total bone volume.

The micro-CT evaluation of enamel-cement thickness, abrasion, and mineral density in teeth in the postmortem interval (PMI): new parameters for the determination of PMI.

OBJECTIVE: The estimation of time of death or the determination of the postmortem interval (PMI) is one of the most important issues in forensic medicine and odontology. However, evaluation of bone and dental hard tissues in PMI could be challenging due to the lack of objective methods with high accuracy. In this respect, micro-CT analysis which has not been used for postmortem evaluation would be beneficial in evaluating hard tissues such as bones and teeth. Therefore, the aim of the present study was to determine the alterations in the hard dental tissue, mineral density of enamel, and the surface abrasion of hard dental tissues of rats in the PMI period with a relatively novel method, micro-CT. METHODS: The present study included 60 female Wistar rats which were divided into six study groups. The rats were sacrificed at the baseline and were left into nature putrefaction process. The study groups were created based on the PMI period as week-0, week-1, week-2, week-4, week-8, and week-12, which included 10 rats in each group. All hemi-mandibles were collected in the determined timelines and the micro-CT analysis was carried out on each group. Mineral density of enamel and the surface abrasion of hard dental tissues were determined. RESULTS: The enamel and cement thickness remained the same in the examined PMI periods. Mineral density of the enamel tissues were also similar until the 8th week but the decrease was significant at 12th week (2.313 gHAp cm3). Surface abrasion of the dental tissues on weeks 4, 8, and 12 were 0.006, 0.024, and 0.024 mm, respectively. CONCLUSION: The present study indicated that surface abrasion and enamel mineral density evaluation via micro-CT can be considered as objective and precise parameters in PMI evaluation in forensic medicine and odontology.

Obturation quality of calcium silicate-based cements placed with different techniques in teeth with perforating internal root resorption: a micro-computed tomographic study.

OBJECTIVES: To evaluate and compare the obturation quality of mineral trioxide aggregate (MTA) and Biodentine placed with hand condensation or indirect ultrasonic activation technique in teeth models simulating perforating internal root resorption (IRR) using micro-computed tomographic (micro-CT) imaging. MATERIALS AND METHODS: Standardized models with perforating IRR cavities were created using 40 extracted single-rooted human teeth and randomly divided into four groups (n = 10). The specimens were obturated with either MTA or Biodentine and the placement technique applied was either hand condensation or indirect ultrasonic activation. Micro-CT scans were performed for the volumetric analysis of voids and filling materials in the resorption cavities and apical portion of the specimens. Data were analyzed using one-way analysis of variance and paired t test. RESULTS: No significant difference was observed between the groups in terms of the percentage volume of filling materials (p > 0.05). The apical portion of the specimens significantly presented less percentage volume of filling materials than the resorption cavities in each group (p < 0.05). CONCLUSIONS: No placement technique produced void-free fillings in teeth with perforating IRR. There was no significant difference between the obturation quality of Biodentine and MTA. The obturation quality in the apical portion of the root canals was inferior than that in the resorption cavities. CLINICAL RELEVANCE: The obturation of the apical region of teeth with perforating IRR is challenging irrespective of the material type and placement technique.

Evaluation of the anticarcinogenic effects of Rutin on brain tissue in mice with Ehrlich ascites carcinoma by micro-computed tomography and histological methods.

BACKGROUND: Studies for new treatment strategies on cancer continue, and new searches continue in the diagnosis and evaluation of cancer. This study examined the possible anticarcinogenic effect of Rutin on the brain tissues of male mice with Ehrlich ascites carcinoma (EAC). MATERIAL AND METHODS: We used micro-computed tomography (micro-CT) and histologically Hematoxylin&Eosin (H&E) staining methods for evaluation. RESULTS: In the evaluation results, we saw a significant decrease in the brain volume of the tumor group to the control group. The difference in volume between the Rutin treatment group and the control group was not significant. In the brain tissues of the tumor group, numerous degenerated neurons characterized by pericellular/perivascular space expansion, cell swelling, or expansion were detected in the cortex and hippocampus regions. We showed a reduction in the damage rate in the Rutin treated group. CONCLUSION: As a result, Rutin was found to have an anticarcinogenic effect. In addition to the classical histological evaluation, we used a newer method, micro-CT, in our study. We believe that this study has important results both in terms of its originality and adding new information to the literature.

The effect of injectable platelet-rich fibrin in combination with autogenous bone grafts on bone healing in an ovariectomized osteoporotic rat model with critical-sized defects.

OBJECTIVES: To assess the impact of autogenous graft materials, including autogenous bone graft (ABG) and injectable platelet-rich fibrin (I-PRF) clots, on bone defect regeneration in ovariectomized osteoporotic rats. METHODS: Wistar rats (6-8 weeks old) were ovariectomized, and surgery began after 8 weeks. A 5-mm defect was created bilaterally in the parietal bones of 16 rats, which were divided into 4 groups. Group A (blank) had untreated defects; group B had defects filled with 0.1 ml of I-PRF, group C had defects filled with 0.1 ml of ABG, and group D had defects filled with a combination of 0.1 ml each of I-PRF and ABG. Four weeks post-surgery, the rats were euthanized. Bone regeneration was evaluated through histopathologic analysis and microcomputed tomography (micro-CT). RESULTS: In ovariectomized rats treated with ABG or I-PRF, bone regeneration was enhanced, with increased periosteal activity, osteoblast count, and new bone volume, as determined histologically. The ABG+I-PRF group had the highest periosteal vascularity, but the difference compared to the ABG group was not statistically significant (p>0.05). Osteoblast numbers were significantly higher in the ABG+I-PRF group than in the blank group (p<0.05). Micro-CT showed the highest mean new bone volume ratio in the ABG+I-PRF group, followed by the ABG group. CONCLUSION: The combined use of ABG and I-PRF enhances bone formation in osteoporotic rats following ovariectomy.