Varying Ti-6Al-4V surface roughness induces different early morphologic and molecular responses in MG63 osteoblast-like cells.

Osteoblast response to Ti implants depends not only on the chemistry of the implant but also on the physical properties of the implant surface, such as microtopography and roughness. This study was undertaken to examine early changes in cell morphology and gene expression during the early phase of osteoblast interaction with titanium alloy (Ti-6Al-4V) surfaces of two different roughnesses. MG63 osteoblast-like cells were cultured for 2, 6, 24, and 72 h on smooth (Ra=0.18+/-0.03 microm) and rough (Ra=2.95+/-0.23 microm) Ti-6Al-4V surfaces. Changes in cell proliferation were assessed by measuring cell number after 72 h in culture. Morphological characteristics were observed by scanning electron microscopy after 2, 6, and 24 h of culture. Changes in gene expression for extracellular signal-regulated kinase 2 (Erk2), type I collagen (alpha2[I] collagen), phospholipase C-gamma2 (Plc-gamma2), and beta-actin were measured by RT-PCR after 6 and 24 h in culture. Cell number was significantly higher on the smooth surface. In scanning electron micrographs, cells on smooth Ti-6Al-4V were spherical and raised up from the surface after 2 h in culture. In contrast, cells on the rough surface adopted an irregular, elongated shape that spanned across pits in the surface. At 24 h, cells on the smooth surface had flattened, become elongate, and covered the surface. In contrast, cells on the rough surface appeared more differentiated in shape and the margins of the cells were irregular, with many processes extending out, following the contour of the surface. Of the genes examined, only Erk2 and beta-actin showed a change in expression with surface roughness. Both genes were upregulated (p<0.05) on the rough surface at 6 h. These results indicate that Ti-6Al-4V surface roughness affects osteoblast proliferation, morphology, and gene expression, and that these effects can be measured after periods as short as 2-6 h.

Identification of Acanthocephala discovered in changran-pickles and myungran-pickles.

To identify acanthocephala found in 'Changran-pickles' and 'Myungran-pickles' each organ was measured in permanent slides. In the present report, the results obtained were as follows: 1. Morphology of male worms: Worms possessed 18-19 longitudinal rows, with 4 hooks per row, which became smaller towards the base of proboscis. Each worm contained two testis and six cement glands arranged linearly. Body 22.0 by 0.8-0.6 mm and 15.0 by 0.6-0.4 mm, proboscis 284.8 by 227.6 micro m and 524.9 by 151.4 micro m, proboscis sheath 1570.7 by 72.7 micro m and 751.9 by 280.4 micro m, lemnisci length 2566.7 and 1085.6, testis 2202.9-1860.5 by 737.0-575.7 micro m and 1033.8-981.1 by 463.1-351.6 micro m, cement glands 940.2 by 441.2 micro m and 610.0 by 369.1 micro m. 2. Morphology of female worms: Worms possessed 14-18 longitudinal rows, with 6-10 hooks per row and become smaller toward the base of proboscis. Each worm contained an uterine bell and uterus in the posterior portion and the eggs filled the body cavity. Body, approximately 14.0 - 51.0 mm by 0.7-0.5 - 2.2-1.4 mm, proboscis 466.1-268.9 micro m by 259.9-252.0 micro m, proboscis sheath 1550.7-506.0 by 298.8-231.1 micro m, lemnisci length 1325.7-473.1 micro m, eggs approximately 112.4 by 28.5 micro m - 51.7 by 14.0 micro m. In this present study, the acanthocephala collected in 'Changran-pickles' and 'Myungran-pickles' were identified as Echinorhynchus gadi by morphological features.