Ultrasound-assisted efficient and convenient method of extracting valuable metals (Ni, Co, and Cd) from waste Ni-Cd batteries using DL-malic acid.

Recycling waste Ni-Cd batteries has received much attention recently because of the serious environmental pollution they cause and to avoid the dissipation of valuable metals. Despite significant research, it is still difficult to efficiently recycle valuable and hazardous metals from waste Ni-Cd batteries in an economical and environmentally friendly manner. This study employed a novel process utilizing ultrasound-assisted leaching to recover Ni, Cd, and Co from waste nickel-cadmium (Ni-Cd) batteries. Organic DL-malic acid served as the leaching agent and H2O2 was employed as an oxidizing agent. The effects of various factors on the recovery efficiency of Ni, Cd, and Co, such as leaching temperature, time, DL-malic acid concentration, pulp density, H2O2 concentration, and ultrasound frequency, were also examined. To predict the chemical compounds present before and after the recycling experiments, the solid residues from the metal extraction were analyzed using XRD, XPS, FE-SEM, and EDS element mapping. Concurrently, ICP-OES was utilized to determine the metal content in the leachate. Under optimized conditions of 90 °C, 90 min, 2M DL-malic acid, 160 mL/g pulp density, and 20% ultrasound frequency, over 83% of Ni, 94% of Cd, and 98% of Co were effectively leached from the waste Ni-Cd battery powder. The leaching kinetics of Ni, Cd, and Co followed the surface chemical reaction control model. The activation energies (Ea) for Ni, Cd, and Co leaching were 21.34, 20.47, and 18.38 kJ/mol, respectively. The findings suggest that ultrasound-assisted leaching is an efficient, cost-effective, environmentally friendly, and sustainable alternative for extracting precious and hazardous metals from waste Ni-Cd batteries. Additionally, it reduces industrial chemical usage and enhances waste management sustainability.

Assessment of soil washing for heavy metal contaminated paddy soil using FeCl3 washing solutions.

In this study, soil washing is applied for the remediation of heavy-metal (Pb, Cu and Zn) contaminated paddy soil located near an abandoned mine area. FeCl3 washing solutions were used in bench-scale soil washing experiments at concentrations in the range of 0.1 to 1 M. The strong acid, HCl was also used in this study for comparison. The washing process was performed at room temperature, mixing at 200 RPM for 1 h and a liquid to solid ratio of 2. A sequential extraction technique was performed to evaluate the chemical fractions of Pb in the soils. The soil washing effectiveness was evaluated and compared against regulations applicable to residential districts (Korean warning standards). The soil washing results showed that the heavy metal concentrations were reduced with increasing concentrations of FeCl3. Moreover, the lowest heavy metal concentrations were obtained with a 1 M FeCl3 washing solution. In the case of Pb removal, a 0.3 M FeCl3 washing solution was required to comply with the Korean warning standard of 200 mg/kg. The lowest Pb concentration of 117 mg/kg was obtained with 1 M FeCl3. Similar washing results were also obtained with HCl. The initial total concentrations for Cu and Zn were below the Korean warning standards of 150 and 300 mg/kg, respectively. Consequently, the reduction in Cu and Zn from the contaminated paddy soil using FeCl3 washing solutions was rather limited. The sequential extraction results showed that the exchangeable and weak acid-soluble fractions of Pb were significantly reduced upon FeCl3 washing.

Is arthritis associated with suicidal ideation and quality of life?

Arthritis is not only a chronic disease but also causes physical inactivity. We investigated the association between arthritis and quality of life and psychological problems, as measured by suicidal ideation. We used data from the 2013 Community Health Survey, and 162,598 persons aged 40 years and older were included as study subjects. Our main focus was to investigate association of arthritis with suicidal ideation and quality of life. Multivariate survey logistic regression analysis was used to estimate the odds ratio for suicidal ideation, and multivariate survey linear regression analysis used to identify associations between variables and scores on the EuroQol Visual Analogue Scale(EQ-VAS). 8.30% of male and 13.90% of female experienced suicidal ideation, and 16.17% of and 21.23% of female suffered from arthritis. Individuals with arthritis were more likely to report suicidal ideation and have lower health-related quality of life (HRQOL) scores. Furthermore, higher rates of suicidal ideation and lower HRQOLs were also associated with older age, low income and less education. Arthritis was associated with higher rates of suicidal ideation and lower HRQOL scores. These results should contribute to the development and implementation of polices and management strategies to alleviate suicidal ideation and increase HRQOL scores among arthritis patients.

Characterization of ZnS Thin Films Grown Using Chemical Bath Deposition with Three Different Complexing Agents.

Cadmium sulfide buffer layer was replaced with zinc sulfide thin film owing to toxicity. ZnS thin films were fabricated using chemical bath deposition. The inhibition of Zn(OH)2 and high uniformity are important factors for the deposition of ZnS. The characteristics of ZnS thin films were analyzed by adding ethylenediamine tetra-acetate acid (EDTA) and hexamethylene tetramine (HMTA). The morphological characteristics of the ZnS buffer layer are closely related to the use of a complexing agent which controls the concentration of Zn2+ ions and Zn(OH)2 in the deposition process. The addition of the complexing agent EDTA accelerated the cluster-cluster method but it exhibited lower uniformity and greater cracking phenomenon. HMTA can be effectively applied to increase the amount of Zn2+ ions forming ZnS. It can be easily found as Zn2 HMTA at high temperatures. The results of the experiment with the addition of HMTA revealed that the surface of the thin film did not change with the increase in the concentration of HMTA, but the thickness of the thin film increased gradually. HMTA promoted the ion-ion method to grow the thin film uniformly, but the speed was slow. Moreover, an experiment by using mixed EDTA and HMTA as the complexing agent was performed. The best ZnS thin film with a transmittance of 83% and a denser surface was prepared using HMTA complexing agent.

Comparison of tracheal reconstruction with allograft, fresh xenograft and artificial trachea scaffold in a rabbit model.

This study evaluated the possibility of tracheal reconstruction with allograft, pig-to-rabbit fresh xenograft or use of a tissue-engineered trachea, and compared acute rejection of three different transplanted tracheal segments in rabbits. Eighteen healthy New Zealand White rabbits weighing 2.5-3.1 kg were transplanted with three different types of trachea substitutes. Two rabbits and two alpha 1, 3-galactosyltransferase gene-knockout pigs weighing 5 kg were used as donors. The rabbits were divided into three groups: an allograft control group consisting of rabbit-to-rabbit allotransplantation animals (n = 6), a fresh xenograft group consisting of pig-to-rabbit xenotransplantation animals (n = 6), and an artificial trachea scaffold group (n = 6). All animals were monitored for 4 weeks for anastomotic complications or infection. The recipients were sacrificed at 28 days after surgery and the grafts were evaluated. On bronchoscopy, all of the fresh xenograft group animals showed ischemic and necrotic changes at 28 days after trachea replacement. The allograft rabbits and the tissue-engineered rabbits showed mild mucosal granulation. The levels of interleukin-2 and interferon-γ in the fresh xenograft group were higher than in other groups. Histopathologic examination of the graft in the fresh xenograft rabbits showed ischemic and necrotic changes, including a loss of epithelium, mucosal granulation, and necrosis of cartilaginous rings. The pig-to-rabbit xenografts showed more severe acute rejection within a month than the rabbits with allograft or artificial trachea-mimetic graft. In addition, the artificial tracheal scaffold used in the present experiment is superior to fresh xenograft and may facilitate tracheal reconstruction in the clinical setting.

Phototherapy suppresses inflammation in human nucleus pulposus cells for intervertebral disc degeneration.

The etiology of intervertebral disc (IVD) degeneration accompanied by low back pain (LBP) is largely unknown, and there are no curative therapies. Painful IVD degeneration is associated with infiltrated macrophage-mediated inflammatory response of human nucleus pulposus (NP) cells. The present study aimed to address the hypothesis that pro-inflammatory cytokines derived from macrophages lead to the altered molecular phenotype of human NP cells and to investigate the effects of phototherapy (630, 525, 465 nm with 16, 32, 64 J/cm2) on pain-related cytokine interleukin (IL)-6 and chemokine IL-8 under inflammatory conditions in human NP cells. Human NP cells were treated with soluble factors derived from macrophages in an inflammatory microenvironment, similar to that found in degenerative IVD. Human NP cells were also treated with phototherapy (630, 525, 465 nm with 16, 32, 64 J/cm2), and their cytokine and chemokine levels were detected. The soluble factors caused modulated expression of IL-6, IL-8, and matrix metalloproteinases (MMPs) at the gene and protein levels, causing a shift toward matrix catabolism through the expression of MMPs and increased pain-related factors via preferential activation of the nuclear factor-kappa B (NF-κB) p50 protein. Importantly, phototherapy attenuated the protein and gene expression of pain-related factor IL-6 at all doses and wavelengths. Interestingly, phototherapy also modulated the protein and gene expression of IL-8, which is responsible for the anabolic response, at a wavelength of 465 nm at all doses, in human NP cells. These findings suggested that phototherapy, at an optimal dose and wavelength, might be a useful therapeutic tool to treat IVD degeneration.

Assessment of Polycyclic Aromatic Hydrocarbons in School Playground Soils in Urban Gwangju, South Korea.

Soil samples from school playground of Gwangju City were analyzed for 16 polycyclic aromatic hydrocarbons (PAHs), and the soil contamination status and the potential cancer risk for students and adults were investigated. Soil samples were collected from 57 sites from 5 districts of Gwangju City in the summer of 2013. Regardless of the sampling site, the ∑PAHs concentrations ranged from 13.2 to 145.5 ng/g (mean 51.2 ng/g). Four and five-ring PAHs were predominant in the soil samples while the fraction of two-ring PAHs was the lowest. Seven carcinogenic PAHs contributed ~ 55% of ∑PAHs in school playground soils. The benzo[a]pyrene (46.4%) and dibenz[a,h]anthracene (41.2%) were the major contributors to toxic equivalent quantity. The strong correlation between carcinogenic PAHs suggested that they originated from the same source either vehicular emission or coal combustion, because they are markers of these pollution sources. The mean cancer risk for students (3.61 × 10-7) and adults (8.41 × 10-6) was in the U.S. EPA safety range (< 10-6).

Image-Guided Laparoscopic Surgical Tool (IGLaST) Based on the Optical Frequency Domain Imaging (OFDI) to Prevent Bleeding.

We present an image-guided laparoscopic surgical tool (IGLaST) to prevent bleeding. By applying optical frequency domain imaging (OFDI) to a specially designed laparoscopic surgical tool, the inside of fatty tissue can be observed before a resection, and the presence and size of blood vessels can be recognized. The optical sensing module on the IGLaST head has a diameter of less than 390 µm and is moved back and forth by a linear servo actuator in the IGLaST body. We proved the feasibility of IGLaST by in vivo imaging inside the fatty tissue of a porcine model. A blood vessel with a diameter of about 2.2 mm was clearly observed. Our proposed scheme can contribute to safe surgery without bleeding by monitoring vessels inside the tissue and can be further expanded to detect invisible nerves of the laparoscopic thyroid during prostate gland surgery.

Immobilization and reduction of bioavailability of lead in shooting range soil through hydrothermal treatment.

Immobilization of Pb in contaminated soil by hydrothermal treatment (HT) under subcritical conditions was investigated using a lab-scale apparatus. The Pb immobilization was evaluated thorough investigating the transformation of Pb fractions and by single chemical extraction. The results showed that HT and treatment temperature significantly affected the immobilization through redistribution of Pb fractions. The results of bioavailability and eco-toxicity assessment demonstrated a drastic decrease in the bioavailable fraction from 41.33 to 14.66%, and an increase in the non-bioavailable fraction from 2.90 to 15.76%. Moreover, the leaching potential of Pb was significantly reduced after treatment. Based on the risk assessment code (RAC), the treated soil residues exhibited medium risk (21.7-14.6 of RAC value for treated soil), which represented a decrease from high risk (41.3 for untreated soil). Immobilization was associated with Pb fractionation from weakly bound to stable fractions. A variety of mechanisms including adsorption and precipitation were suspected to be responsible for Pb immobilization. The findings of this study suggest that the HT may facilitate quantitative reduction of the bioavailability and eco-toxicity of Pb-contaminated soil. Considering the effectiveness of HT in remediating contaminated soil with organic pollutants, this approach might enable remediation of soil co-contaminated with organics and heavy metals.

Association between weight control failure and suicidal ideation in overweight and obese adults: a cross-sectional study.

BACKGROUND: Korea has the highest suicide rate in the OECD and is one of the few OECD countries whose suicide rates have not decreased in recent years. To address these issues, we investigated the effects of weight control failure on suicidal ideation in the overweight and obese populations. METHODS: We performed a cross-sectional study using data from the Korea National Health and Nutrition Examination Survey (2008-2012) consisting of 6621 individuals 40 years of age or older. Logistic regression analysis was used to identify the relationship between weight control failure and suicidal ideation in the overweight and obese populations. RESULTS: A total of 6621 participants were analyzed in this study (overweight group: 2439; obese group: 4182). Among them, weight control failure (weight gain with weight loss efforts) was experienced in 962 obese (males 16.3%, females 29.6%) and 412 overweight individuals (males 9.1%, females 23.4%). Weight control failure was significantly associated with suicidal ideation in obese females (OR = 1.70, 95% CI 1.21-2.39), but this association was not significant in obese males or in either sex of the overweight group. CONCLUSIONS: Findings from this study suggest that weight control failure is associated with an increased risk of suicidal ideation among obese women. Furthermore, intervention programs that aim to address the prevalence of suicide, especially for obese women, are needed.

Chemical Speciation and Quantitative Evaluation of Heavy Metal Pollution Hazards in Two Army Shooting Range Backstop Soils.

The chemical speciation and ecological risk assessment of heavy metals in two shooting range backstop soils in Korea were studied. Both soils were highly contaminated with Cd, Cu, Pb, and Sb. The chemical speciation of heavy metals reflected the present status of contamination, which could help in promoting management practices. We-rye soil had a higher proportion of exchangeable and carbonate bound metals and water-extractable Cd and Sb than the Cho-do soil. Bioavailable Pb represented 42 % of the total Pb content in both soils. A significant amount of Sb was found in the two most bioavailable fractions, amounting to ~32 % in the soil samples, in good agreement with the batch leaching test using water. Based on the values of ecological risk indices, both soils showed extremely high potential risk and may represent serious environmental problems.

Subcritical water treatment of explosive and heavy metals co-contaminated soil: Removal of the explosive, and immobilization and risk assessment of heavy metals.

Co-contamination of explosives and heavy metals (HMs) in soil, particularly army shooting range soil, has received increasing environmental concern due to toxicity and risks to ecological systems. In this study, a subcritical water (SCW) extraction process was used to remediate the explosives-plus-HMs-co-contaminated soil. A quantitative evaluation of explosives in the treated soil, compared with untreated soil, was applied to assess explosive removal. The immobilization of HMs was assessed by toxicity characteristic leaching procedure tests, and by investigating the migration of HMs fractions. The environmental risk of HMs in the soil residue was assessed according to the risk assessment code (RAC) and ecological risk indices (Er and RI). The results indicated that SCW treatment could eliminate the explosives, >99%, during the remediation, while the HM was effectively immobilized. The effect of water temperature on reducing the explosives and the risk of HMs in soil was observed. A marked increase in the non-bioavailable concentration of each HM was observed, and the leaching rate of HMs was decreased by 70-97% after SCW treatment at 250 °C, showing the effective immobilization of HMs. According to the RAC or RI, each tested HM showed no or low risk to the environment after treatment.

Soil washing of fluorine contaminated soil using various washing solutions.

Bench-scale soil washing experiments were conducted to remove fluoride from contaminated soils. Five washing solutions including hydrochloric acid (HCl), nitric acid (HNO3), sodium hydroxide (NaOH), sulfuric acid (H2SO4) and tartaric acid (C4H6O6) were tested. The concentration of the washing solutions used ranged from 0.1 to 3 M with a liquid to solid ratio of 10. The soil washing results showed that the most effective washing solution for the removal of fluoride from contaminated soils was HCl. The highest fluoride removal results of approximately 97 % from the contaminated soil were obtained using 3 M HCl. The fluoride removal efficiency of the washing solution increases in the following order: C4H6O6 < NaOH < H2SO4 < HNO3 < HCl.

3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering (SLS) and melt extrusion.

A direct and comprehensive comparative study on different 3D printing modalities was performed. We employed two representative 3D printing modalities, laser- and extrusion-based, which are currently used to produce patient-specific medical implants for clinical translation, to assess how these two different 3D printing modalities affect printing outcomes. The same solid and porous constructs were created from the same biomaterial, a blend of 96% poly-ε-caprolactone (PCL) and 4% hydroxyapatite (HA), using two different 3D printing modalities. Constructs were analyzed to assess their printing characteristics, including morphological, mechanical, and biological properties. We also performed an in vitro accelerated degradation study to compare their degradation behaviors. Despite the same input material, the 3D constructs created from different 3D printing modalities showed distinct differences in morphology, surface roughness and internal void fraction, which resulted in different mechanical properties and cell responses. In addition, the constructs exhibited different degradation rates depending on the 3D printing modalities. Given that each 3D printing modality has inherent characteristics that impact printing outcomes and ultimately implant performance, understanding the characteristics is crucial in selecting the 3D printing modality to create reliable biomedical implants.

Flexible and transparent nanohole-patterned films with antibacterial properties against Staphylococcus aureus.

In this paper, we explore the development of a multi-functional surface designed to tackle the challenges posed by Staphylococcus aureus (S. aureus), a common opportunistic pathogen. Infections caused by S. aureus during surgical procedures highlight the need for effective strategies to inhibit its adhesion, growth, and colonization, particularly on the surfaces of invasive medical devices. Until now, most existing research has focused on nanopillar structures (positive topographies). Uniform nanopillar arrays have been shown to control bacterial behavior based on the spacing between nanopillars. However, nanopillar structures are susceptible to external friction, impact, and force, making it challenging to maintain their antibacterial properties. Therefore, in this study, we investigate the antibacterial behavior of nanohole structures, which offer relatively superior mechanical robustness compared to nanopillars. Moreover, for applications in medical devices such as laparoscopes, there is a pressing need for surfaces that are not only transparent and flexible (or curved) but are also equipped with antibacterial properties. Our study introduces a scalable multi-functional surface that synergistically combines antibacterial and anti-fog properties. This is achieved by fabricating thin films with variously sized holes (ranging from 0.3 µm to 4 µm) using polyurethane acrylate (PUA). We assessed the activity of S. aureus on these surfaces and found that a 1 µm-diameter-hole pattern significantly reduced the presence of live S. aureus, without any detection of dead S. aureus. This bacteriostatic effect is attributed to the restricted proliferation due to the confined area provided by the hole pattern. However, the persistence of some live S. aureus on the surface necessitates further measures to minimize bacterial adhesion and enhance antibacterial effectiveness. To address this challenge, we coated the zwitterionic polymer 2-methacryloyloxyethyl phosphorylcholine (MPC) onto the nanohole pattern surface to reduce S. aureus adhesion. Moreover, in long-term experiments on surfaces, the MPC-coated effectively inhibited the colonization of S. aureus (18 h; 82%, 7 days; 83%, and 14 days; 68% antibacterial rate). By integrating PUA, MPC, and nanohole architectures into a single, flexible platform, we achieved a multi-functional surface catering to transparency, anti-fogging, and anti-biofouling requirements. This innovative approach marks a significant advancement in surface engineering, offering a versatile solution applicable in various fields, particularly in preventing S. aureus contamination in invasive medical devices like laparoscopes. The resultant surface, characterized by its transparency, flexibility, and antibacterial functionality, stands out as a promising candidate for mitigating S. aureus-related risks in medical applications.

Stabilization of lead and copper contaminated firing range soil using calcined oyster shells and fly ash.

A stabilization/solidification treatment scheme was devised to stabilize Pb and Cu contaminated soil from a firing range using renewable waste resources as additives, namely waste oyster shells (WOS) and fly ash (FA). The WOS, serving as the primary stabilizing agent, was pre-treated at a high temperature to activate quicklime from calcite. Class C FA was used as a secondary additive along with the calcined oyster shells (COS). The effectiveness of the treatment was evaluated by means of the toxicity characteristic leaching procedure (TCLP) and the 0.1 M HCl extraction tests following a curing period of 28 days. The combined treatment with 10 wt% COS and 5 wt% FA cause a significant reduction in Pb (>98 %) and Cu (>96 %) leachability which was indicated by the results from both extraction tests (TCLP and 0.1 M HCl). Scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) analyses are used to investigate the mechanism responsible for Pb and Cu stabilization. SEM-EDX results indicate that effective Pb and Cu immobilization using the combined COS-FA treatment is most probably associated with ettringite and pozzolanic reaction products. The treatment results suggest that the combined COS-FA treatment is a cost effective method for the stabilization of firing range soil.

Catalytic depolymerization of Kraft lignin to high yield alkylated-phenols over CoMo/SBA-15 catalyst in supercritical ethanol.

Lignin is generally considered to be a renewable and sustainable resource of aromatic chemicals. However, the depolymerization of Kraft lignin (KL) for the production of selective phenolic monomers presents a significant challenge due to its highly recalcitrant nature. Therefore, in this work, we investigated the effect of metal sites and acid active sites on Mo/SBA-15, Co/SBA-15 and CoMo/SBA-15 catalysts in supercritical ethanol for the depolymerization of KL to produce phenolic monomers. Ethanol was used as a hydrogen donor solvent instead of using external hydrogen. Results showed that the bimetallic CoMo/SBA-15 catalyst exhibited significantly higher catalytic activity compared to the monometallic, Co/SBA-15, Mo/SBA-15 or bare SBA-15. The highest phenolic monomers yield of 27.04 wt% was achieved at 290 °C for 4 h over CoMo/SBA-15 catalyst. The inter-unit linkages such as ß-O-4', ß-ß and α-O-4' in lignin were considerably cleaved during the catalytic depolymerization in supercritical ethanol. Meanwhile, higher functionality of carbonyl compounds was present in the non-catalytic bio-oil, while more alkylated phenols were produced over CoMo/SBA-15 catalyst. The major phenolic monomers identified in the catalytic bio-oil were 4-ethylguaiacol (9.15 wt%), 4-methylguaiacol (6.80 wt%), and 4-propylguaiacol (2.85 wt%). These findings suggest that the metal sites and abundant acid active sites of CoMo/SBA-15 had a synergistic effect toward the degradation of different linkages of lignin and production of selective phenolic monomers in bio-oils.

In vitro fatigue behavior and in vivo osseointegration of the auxetic porous bone screw.

The incidence of screw loosening, migration, and pullout caused by the insufficient screw-bone fixation stability is relatively high in clinical practice. To solve this issue, the auxetic unit-based porous bone screw (AS) has been put forward in our previous work. Its favorable auxetic effect can improve the primary screw-bone fixation stability after implantation. However, porous structure affected the fatigue behavior and in vivo longevity of bone screw. In this study, in vitro fatigue behaviors and in vivo osseointegration performance of the re-entrant unit-based titanium auxetic bone screw were studied. The tensile-tensile fatigue behaviors of AS and nonauxetic bone screw (NS) with the same porosity (51%) were compared via fatigue experiments, fracture analysis, and numerical simulation. The in vivo osseointegration of AS and NS were compared via animal experiment and biomechanical analysis. Additionally, the effects of in vivo dynamic tensile loading on the osseointegration of AS and NS were investigated and analyzed. The fatigue strength of AS was approximately 43% lower while its osseointegration performance was better than NS. Under in vivo dynamic tensile loading, the osseointegration of AS and NS both improved significantly, with the maximum increase of approximately 15%. Preferrable osseointegration of AS might compensate for the shortage of fatigue resistance, ensuring its long-term stability in vivo. Adequate auxetic effect and long-term stability of the AS was supposed to provide enough screw-bone fixation stability to overcome the shortages of the solid bone screw, developing the success of surgery and showing significant clinical application prospects in orthopedic surgery. STATEMENT OF SIGNIFICANCE: This research investigated the high-cycle fatigue behavior of re-entrant unit-based auxetic bone screw under tensile-tensile cyclic loading and its osseointegration performance, which has not been focused on in existing studies. The fatigue strength of auxetic bone screw was lower while the osseointegration was better than non-auxetic bone screw, especially under in vivo tensile loading. Favorable osseointegration of auxetic bone screw might compensate for the shortage of fatigue resistance, ensuring its long-term stability and longevity in vivo. This suggested that with adequate auxetic effect and long-term stability, the auxetic bone screw had significant application prospects in orthopedic surgery. Findings of this study will provide a theoretical guidance for design optimization and clinical application of the auxetic bone screw.

Recycling of NCM cathode material from spent lithium-ion batteries via polyvinyl chloride and chlorinated polyvinyl chloride in subcritical water: A comparative study.

To date, numerous studies have explored recycling of lithium, nickel, cobalt, and manganese (NCM) from spent lithium-ion batteries (LIBs). Nevertheless, the leaching and efficient separation of the precious metals from NCM active cathode material via an environmentally benign and economical process is still challenging. Therefore, in this research, we present a novel and energy an efficient route through which to leach valuable metals, for example, lithium (Li), nickel (Ni), cobalt (Co), and manganese (Mn) from the NCM cathode material of the waste LIBs using water-containing waste chlorinated polyvinyl chloride (CPVC) or polyvinyl chloride (PVC) in a batch reactor. Parameters such as temperature, time, liquid-solid, and mass ratios on the extraction efficiencies of Li, Ni, Co, and Mn were carefully examined. The outcomes show that CPVC performed better than PVC for the extraction of valuable metals from NCM material, and this was attributed to its high Cl contents. The maximum extraction efficiencies of Li, Ni, Co, and Mn (99.15%, 98.10%, 99.30%, and 100%, respectively) were achieved under optimized reaction conditions: a temperature of 290 °C, reaction time of 1 h, a liquid-solid ratio 60:1 mL/g and solid to solid mass ratio of 1:3. The apparent activation energies (Ea) for Li, Ni, Co, and Mn were computed to be (24.42, 28.85, 29.67, and 28.79) kJ/mol. The results obtained in this work, indicated that it may contribute to efforts aiming to reduce industrial chemical consumption and increase sustainability in waste management technique.

Strain Transfer of Fiber Bragg Grating Sensor Externally Bonded to FRP Strip for Structural Monitoring after Reinforcement.

To date, a method of attaching a FRP (fiber-reinforced polymer) to concrete members with epoxy has been widely applied to increase the strength of the member. However, there are cases in which the adhesion of the epoxy deteriorates over time and the reinforcing effect of the FRP is gradually lost. Therefore, monitoring whether or not the reinforcing effect is properly maintained is needed in order to prevent a decrease in the structural performance of the member improved by FRP reinforcement. In this regard, this study examines FRP with OF (optical fiber) sensors to monitor the reinforcing effect of FRP in concrete structural members. In particular, this paper seeks to determine an appropriate adhesion length when FBG (fiber Bragg grating) based OF sensors are externally bonded to FRP strips with epoxy resin. To this end, a tensile test was carried out to evaluate the sensing performance according to the adhesion length. In addition, an analytical approach was performed and the result were compared with test result. The results of the experimental and analytical studies showed that the strain generated in the FRP is sufficiently transferred to the OF if the total adhesion length of it is 40 mm or more in consideration of the error in the epoxy thickness.