Deposition of Fluorescently Tagged Lysozyme on Contact Lenses in a Physiological Blink Model.

PURPOSE: To visualize the deposition of fluorescein isothiocyanate (FITC) lysozyme on daily disposable contact lenses (CLs) using a novel blink model. METHODS: Three daily disposable conventional hydrogel CLs (etafilcon A, omafilcon A, and nelfilcon A) and three silicone hydrogel CLs (delefilcon A, senofilcon A, and somofilcon A) were evaluated in the study. The CLs were mounted onto a novel blink model and exposed to an artificial tear solution containing FITC lysozyme for 2 and 10 hr. The flow rate and blink speed were set to 1 µL/min and 6 blinks/min, respectively. After the incubation period, a 5-mm-diameter disc was punched out from the center of the lens and mounted on a microscope slide. The slides were imaged using the Zeiss 510 Meta confocal laser scanning microscope, which scanned the lens from the front to the back surface at 5-µm increments. RESULTS: There was an increase in deposition of FITC lysozyme for all lens types with increasing incubation time (P<0.05), with the exception of somofilcon A, which did not show statistical significance between 2 and 10 hr (P>0.05). The conventional hydrogel CLs deposited higher amounts of FITC lysozyme than the silicone hydrogel CLs (P<0.001), with etafilcon A depositing the highest at all time points (P<0.05). Interestingly, at the 2-hr incubation time, most CLs showed a higher amount of deposition at the front surface than the back surface of the lens. In particular, etafilcon A showed preferred deposition at the front surface at all time points. CONCLUSION: The results suggest that there is differential deposition at the front surface of the CL, which is exposed to the prelens tear film, compared with the back surface of the CL, which is exposed to the postlens tear film. Therefore, it may be beneficial to design CL materials with differing surface properties for the front and back surfaces of the CL to enhance interactions with the tear film and ocular surface.

Lysozyme Deposition on Contact Lenses in an In Vitro Blink-Simulation Eye Model Versus a Static Vial Deposition Model.

PURPOSE: To evaluate active lysozyme deposition on daily disposable (DD) contact lenses (CL) using a novel in vitro blink model. METHODS: Three conventional hydrogel DD CL materials (etafilcon A, omafilcon A, nelfilcon A) and three silicone hydrogel DD CL materials (delefilcon A, senofilcon A, somofilcon A) were tested. The device blink rate was set to 6 blinks/min with a tear flow rate of 1 µL/min using an artificial tear solution (ATS) containing lysozyme and other typical tear film components. After incubation at 2, 4, or 8 hr, lenses were removed, and lysozyme activity was measured. A separate experiment was conducted with lenses incubated in a static vial containing 480 µL of ATS. RESULTS: Etafilcon A deposited significantly higher amounts of active lysozyme (402±102 µg/lens) than other lens materials after 8 hr (P<0.0001). Etafilcon A had a higher amount of active lysozyme using the blink model compared with the static vial (P=0.0435), whereas somofilcon A (P=0.0076) and senofilcon A (P=0.0019) had a higher amount of lysozyme activity in the vial compared with the blink model. CONCLUSION: The blink model can be tuned to provide quantitative data that closely mimics ex vivo studies and can be used to model deposition of lysozyme on CL materials.

Uptake and Release of a Multipurpose Solution Biocide (MAP-D) From Hydrogel and Silicone Hydrogel Contact Lenses Using a Radiolabel Methodology.

PURPOSE: The purpose of this study was to evaluate the uptake and release of radiolabelled myristamidopropyl dimethylamine (MAP-D) on reusable daily wear contact lenses (CLs) over 7 days. METHODS: Three silicone hydrogel (SH) CL materials (lotrafilcon B, balafilcon A, senofilcon A) and two conventional hydrogel (CH) materials (etafilcon A, omafilcon A) were tested. A short-term (experiment 1, N=4) and a longer-term (experiment 2, N=3) study was conducted. In experiment 1, the CLs were incubated in 2 mL of phosphate buffered solution (PBS) containing 14C MAP-D (5 µg/mL) for 8 hrs. The release of 14C MAP-D was measured at t=0.25, 0.5, 1, 2, 4, 8, and 24 hr in PBS. In experiment 2, the CLs were incubated in the 14C MAP-D solution for 8 hrs followed by a 16-hr release in PBS. This cycle was repeated daily for 7 days. At the end of both experiments, lenses were extracted to determine the total uptake of MAP-D. The radioactivity was measured using a beta scintillation counter. RESULTS: In experiment 1, all three SH lenses sorbed similar amounts of MAP-D (P=0.99), all of which were higher than the two CH materials (P<0.01). However, the CH materials released a greater amount of MAP-D than the SH materials (P<0.01). In experiment 2, the uptake of MAP-D in SH materials increased over 7 days, whereas the amount of MAP-D remained constant in the CH materials (P=0.99). Similar to experiment 1, the CH lenses released more MAP-D than SH lenses after 7 days (P<0.01). CONCLUSION: The SH materials absorbed greater amounts of MAP-D compared to CH materials. However, the CH materials released the greatest amount of MAP-D. Radioactive labelling of MAP-D offers a highly sensitive method of assessing the uptake and release profiles of biocides to CL materials.

Uptake and Release of Polyvinyl Alcohol from Hydrogel Daily Disposable Contact Lenses.

SIGNIFICANCE: Polyvinyl alcohol is a wetting agent that could reduce the symptoms of dry eye and contact lens discomfort. Currently, only one lens type, nelfilcon A (DAILIES AquaComfort Plus), releases polyvinyl alcohol. The concept of releasing this agent from contact lenses could be applied to other lens materials. PURPOSE: The purpose of this study was to measure the release of polyvinyl alcohol from commercially available hydrogel daily disposable contact lenses using refractive index and iodine-borate methods. METHODS: Etafilcon A, omafilcon A, and nelfilcon A were soaked in phosphate-buffered saline and 0.2% trifluoroacetic acid/acetonitile for 24 hours to remove residual blister pack components. The lenses were then incubated in a 10-mg/mL solution of polyvinyl alcohol for 24 hours. After the incubation period, the lenses were placed in 2 mL of phosphate-buffered saline. At specified time intervals, t = 0.5, 1, 2, 4, 8, 12, and 24 hours, the samples were evaluated using refractive index and an iodine-borate assay. Polyvinyl alcohol uptake was determined by extracting the lenses with methanol for 24 hours. RESULTS: There were no differences in the uptake of polyvinyl alcohol between lens types (P > .05). The release of this wetting agent for all lens types followed a burst-plateau profile after the first 30 minutes (P > .05). Nelfilcon A had a slightly higher release of polyvinyl alcohol (P < .05) than did etafilcon A but was similar to omafilcon A (P > .05). CONCLUSIONS: The results suggest that the contact lenses tested in this study have similar efficiency in delivering polyvinyl alcohol.

Depth Profile Assessment of the Early Phase Deposition of Lysozyme on Soft Contact Lens Materials Using a Novel In Vitro Eye Model.

OBJECTIVE: To characterize the location of fluorescently labeled lysozyme on commercial contact lenses (CLs) using an in vitro eye model that simulates tear volume, tear flow, air exposure, and mechanical wear. METHODS: One commercially available conventional hydrogel CL material (etafilcon A) and three silicone hydrogel CL materials (balafilcon A, lotrafilcon B, and senofilcon A) were evaluated in this study. The CLs were mounted on the in vitro eye model and exposed to artificial tear fluid containing fluorescein isothiocyanate (FITC)-labeled lysozyme for 2 and 10 hrs. After these short incubation periods, circular discs were punched from the CLs at the center and periphery and were prepared for confocal laser scanning microscopy (CLSM). The CLSM captured a series of consecutive images spaced 5 µm apart, and the resulting images were rendered into two dimensional cross-sectional views of the CL. The mean fluorescence at each 5 µm slice was used to generate a histogram depicting the penetration of FITC-lysozyme into CLs. RESULTS: For both incubation periods, the CLSM images and histogram of etafilcon A showed that FITC-lysozyme is more concentrated at the lens surface, with a moderate amount of deposition in the lens matrix. For balafilcon A, FITC-lysozyme was evenly distributed throughout the lens. For lotrafilcon B, there was a greater amount of FITC-lysozyme deposition on the surfaces of the lens versus the matrix. Senofilcon A had differential FITC-lysozyme distribution profiles depending on the location of the lens. At the lens periphery, FITC-lysozyme primarily deposited on the surface, whereas FITC-lysozyme was uniformly distributed at the center of the lens. CONCLUSIONS: With the use of a sophisticated in vitro eye model, the study revealed a complex deposition pattern of FITC-labeled lysozyme on various CL materials after short periods of exposure. An understanding of the early deposition pattern of lysozyme on different CL material may elucidate new insights into the processes behind CL discomfort.

The Use of Contact Lenses as Biosensors.

: The tear film is a complex multilayer film consisting of various proteins, enzymes, and lipids and can express a number of biomarkers in cases of disease. The development of a contact lens sensor presents a noninvasive alternative for the detection and management of various diseases. Recent work has resulted in the commercialization of a device to monitor intraocular pressure for up to 24 h, and there are extensive efforts underway to develop a contact lens sensor capable of continuous glucose tear film monitoring to manage diabetes. This clinical perspective will highlight the major developments within this field and list some of the major challenges that still need to be addressed.

Release of Fluconazole from Contact Lenses Using a Novel In Vitro Eye Model.

PURPOSE: Rapid drug release followed by a plateau phase is a common observation with drug delivery from contact lenses (CLs) when evaluated in a vial. The aim of this study was to compare the release of fluconazole from seven commercially available daily disposable CLs using a conventional vial-based method with a novel in vitro eye model. METHODS: An eye model was created using two 3-dimensional printed molds, which were filled with polydimethylsiloxane to obtain an inexpensive model that would mimic the eyeball and eyelid. The model was integrated with a microfluidic syringe pump, and the flow-through was collected in a 12-well microliter plate. Four commercial daily disposable conventional hydrogels (nelfilcon A, omafilcon A, etafilcon A, ocufilcon B) and three silicone hydrogels (somofilcon A, narafilcon A, delefilcon A) were evaluated. These CLs were incubated with fluconazole for 24 h. The drug release was measured in a vial containing 4.8 mL of phosphate-buffered saline and in the polydimethylsiloxane eye model with a 4.8-mL tear flow across 24 h. RESULTS: Overall, conventional hydrogel CLs had a higher uptake and release of fluconazole than silicone hydrogel CLs (p < 0.05). A higher drug release was observed in the vial condition compared with the eye model (p < 0.001). In the vial system, the drugs were rapidly released from the CL within the first 2 h, followed by a plateau phase. In contrast, drug release in the eye model under low tear volume was sustained and did not reach a plateau across 24 h (p < 0.05). CONCLUSIONS: Rapid drug release results from using a vial as the release system. Under low tear volume at physiological tear flow, commercial CLs can maintain a sustained drug release profile for up to 24 h. However, eyes with fungal keratitis may have increased tearing, which would significantly accelerate drug release.

Effects of Antifungal Soaked Silicone Hydrogel Contact Lenses on Candida albicans in an Agar Eye Model.

PURPOSE: To evaluate the effects of two commercial silicone hydrogel contact lenses (CLs) soaked with natamycin (NA) or fluconazole (FL) on the growth of Candida albicans in an in vitro eye model. METHODS: Three-D printed molds were used as a cast for making eye-shaped models comprising potato dextrose agar. Senofilcon A (SA) and lotrafilcon B (LB) CLs were incubated with either 2 mL of NA or FL at a concentration of 1 mg/mL for 24 hr. To simulate a fungal infection, the eye models were coated with C. albicans. The drug-soaked lenses were placed on top of the eye models. Seven experimental conditions were examined: (1) NA-SA, (2) NA-LB, (3) FL-SA, (4) FL-LB, (5) SA, (6) LB, and (7) control-no lens. At specified time points (t=1, 8, 16, 24, 48 hr), the agar eyes from each experimental condition were removed from the incubator and photographed. The yeast cells from the 24 and 48 hr time point were also analyzed using light microscopy. RESULTS: At 24 and 48 hr, there was considerable growth observed for all conditions except for the NA-SA and NA-LB conditions. When observed under the microscope at 24 and 48 hr, the morphology of the yeast cells in the FL-SA and SA condition were similar to that of the control (oval shaped). There was limited hyphae growth observed for LB and significant visible hyphae growth for the NA-LB group. For NA-SA, NA-LB, and FL-LB groups, the cells were significantly smaller compared with the control. CONCLUSIONS: For NA-SA and NA-LB, there was limited growth of C. albicans observed on the eye models even after 48 hr. Under the microscope, the cell morphology differ noticeably between each testing condition, and is dependent on drug-lens combinations.

Extraction versus in situ techniques for measuring surface-adsorbed lysozyme.

PURPOSE: To compare two techniques for measuring the activity of lysozyme deposited onto hydrogel contact lens and to image the binding of Micrococcus lysodeikticus to contact lenses. METHODS: Using a previously described protein extraction technique and a recently developed in situ technique, we measured the time-dependent activity of adsorbed lysozyme on six different contact lens materials during the first minute and up to 1 week of interaction with the material surface. Total activity of extracted lysozyme, total in situ activity, and the activity of the outer surface layer of sorbed lysozyme were determined using the two different techniques. Micrococcal cellular interaction with surface-adsorbed lysozyme was imaged using confocal microscopy. RESULTS: The differences between total extracted activities, total in situ activities, and surface activities were both measurable and material specific. In most cases, total extracted activity is greater than total in situ activity, which, in turn, is greater than surface activity. After 1 week, etafilcon A had the highest extracted activity at 137 µg/lens, followed by omafilcon A, balafilcon A, comfilcon A, senofilcon A, and lotrafilcon B at 27.4, 2.85, 2.02, 0.46, and 0.27 µg/lens, respectively. Micrococcal cell adhesion was greatest on contact lenses with high contact angles, such as balafilcon A, omafilcon A, and senofilcon A and lowest on contact lenses with low contact angles, such as etafilcon A, comfilcon A, and lotrafilcon B. Subsequent removal/prevention of adhered micrococcal cells was greatest on balafilcon A, which had the highest surface activity, and lowest on lotrafilcon B, which had the lowest surface activity. CONCLUSIONS: This study has measured and made direct comparisons between two established techniques for measuring the activity of adsorbed lysozyme. The extraction technique determines the activity of underlying layers of lysozyme or lysozyme within the matrix of the material. Conversely, the in situ technique allows conclusions to be drawn about only the biologically relevant lysozyme including the activity of just the outer surface of adsorbed lysozyme.

Injectable and 3D Extrusion Printable Hydrophilic Silicone-Based Hydrogels for Controlled Ocular Delivery of Ophthalmic Drugs.

While silicone elastomers have found widespread use in the biomedical industry, 3D printing them has proven to be difficult due to the material's slow drying time, low viscosity, and hydrophobicity. Herein, we arrested the hydrophilic silicone (HS) macrochains into a semi-interpenetrating polymer network (semi-IPN) via an in situ photogelation-assisted 3D microextrusion printing technique. The flow behavior of the pregel solutions and the mechanical properties of the printed HS hydrogels were tested, showing a high elastic modulus (approximately 15 kPa), a low tan δ, high elasticity, and delayed network rupturing. The uniaxial compression tests demonstrated a nearly negligible permanent deformation, suggesting that the printed hybrid hydrogel maintained its elastic properties. Drug loading and diffusion in the microporous hydrogel are shown via the non-Fickian anomalous transport mechanism, leading to highly tunable loading/releasing profiles (approximately 20% cumulative release) depending on the HS concentration. The drug encapsulation exhibits exceptional stability, remaining intact without any degradation even after a storage period of 1 month. As far as we know, this is the first soft biomaterial based on HS that functions as an exceptional controlled drug delivery device.

A review of using Traditional Chinese Medicine in the management of glaucoma and cataract.

Traditional Chinese Medicine has a long history in ophthalmology in China. Over 250 kinds of Traditional Chinese Medicine have been recorded in ancient books for the management of eye diseases, which may provide an alternative or supplement to current ocular therapies. However, the core holistic philosophy of Traditional Chinese Medicine that makes it attractive can also hinder its understanding from a scientific perspective - in particular, determining true cause and effect. This review focused on how Traditional Chinese Medicine could be applied to two prevalent ocular diseases, glaucoma, and cataract. The literature on preclinical and clinical studies in both English and Chinese on the use of Traditional Chinese Medicine to treat these two diseases was reviewed. The pharmacological effects, safety profile, and drug-herb interaction of selected herbal formulas were also investigated. Finally, key considerations for conducting future Traditional Chinese Medicine studies are discussed.

Evaluating the in vitro wettability and coefficient of friction of a novel and contemporary reusable silicone hydrogel contact lens materials using an in vitro blink model.

PURPOSE: To evaluate the in vitro wettability and coefficient of friction of a novel amphiphilic polymeric surfactant (APS), poly(oxyethylene)-co-poly(oxybutylene) (PEO-PBO) releasing silicone hydrogel (SiHy) contact lens material (serafilcon A), compared to other reusable SiHy lens materials. METHODS: The release of fluorescently-labelled nitrobenzoxadiazole (NBD)-PEO-PBO was evaluated from serafilcon A over 7 days in a vial. The wettability and coefficient of friction of serafilcon A and three contemporary SiHy contact lens materials (senofilcon A; samfilcon A; comfilcon A) were evaluated using an in vitro blink model over their recommended wearing period; t = 0, 1, 7, 14 days for all lens types and t = 30 days for samfilcon A and comfilcon A (n = 4). Sessile drop contact angles were determined and in vitro non-invasive keratographic break-up time (NIKBUT) measurements were assessed on a blink model via the OCULUS Keratograph 5 M. The coefficient of friction was measured using a nano tribometer. RESULTS: The relative fluorescence of NBD-PEO-PBO decreased in serafilcon A by approximately 18 % after 7 days. The amount of NBD-PEO-PBO released on day 7 was 50 % less than the amount released on day 1 (6.5±1.0 vs 3.4±0.5 µg/lens). The reduction in PEO-PBO in the lens also coincided with an increase in contact angles for serafilcon A after 7 days (p < 0.05), although there were no changes in NIKBUT or coefficient of friction (p > 0.05). The other contact lens materials had stable contact angles and NIKBUT over their recommended wearing period (p > 0.05), with the exception of samfilcon A, which had an increase in contact angle after 14 days as compared to t = 0 (p < 0.05). Senofilcon A and samfilcon A also showed an increase in coefficient of friction at 14 and 30 days, respectively, compared to their blister pack values (p < 0.05). CONCLUSION: The results indicate that serafilcon A gradually depletes its reserve of PEO-PBO over 1 week, but this decrease did not significantly change the lens performance in vitro during this time frame.

In vitro uptake and release of natamycin from conventional and silicone hydrogel contact lens materials.

OBJECTIVES: To investigate the uptake and release of the antifungal ocular drug, natamycin from commercially available conventional hydrogel (CH) and silicone hydrogel (SH) contact lens (CL) materials and to evaluate the effectiveness of this delivery method. METHODS: Five commercial SH CLs (balafilcon A, comfilcon A, galyfilcon A, senofilcon A, and lotrafilcon B) and four CH CLs (etafilcon A, omafilcon A, polymacon, vifilcon A) were examined in this study. These lenses were incubated with natamycin solubilized in dimethyl sulfoxide, and the release of the drug from these lenses, in Unisol 4 pH 7.4 at 32±1°C, was determined using UV-visible spectrophotometry at 305 nm over 24 hours. RESULTS: There was a significant uptake of natamycin between 0 hour and 24 hours (P<0.05) for all CL materials. However, there was no significant difference between any of the lens materials, regardless of their composition (P>0.05). There was a significant difference in release between all the SH materials (P<0.05) and CH materials (P<0.05). All CL materials showed a significant increase in the release of natamycin until 1 hour (P<0.05), which was followed by a plateau (P>0.05). Overall, the release of natamycin was higher in CH than SH lenses (P<0.001). CONCLUSIONS: All CLs released clinically relevant concentrations of natamycin within 30 minutes, but this release reached a plateau after approximately 1 hour. Further CL material development will be necessary to produce a slow and sustained drug releasing device for the delivery of natamycin.

A Rapid Screening Platform for Simultaneous Evaluation of Biodegradation and Therapeutic Release of an Ocular Hydrogel.

This study attempts to address the challenge of accurately measuring the degradation of biodegradable hydrogels, which are frequently employed in drug delivery for controlled and sustained release. The traditional method utilizes a mass-loss approach, which is cumbersome and time consuming. The aim of this study was to develop an innovative screening platform using a millifluidic device coupled with automated image analysis to measure the degradation of Gelatin methacrylate (GelMA) and the subsequent release of an entrapped wetting agent, polyvinyl alcohol (PVA). Gel samples were placed within circular wells on a custom millifluidic chip and stained with a red dye for enhanced visualization. A camera module captured time-lapse images of the gels throughout their degradation. An image-analysis algorithm was used to translate the image data into degradation rates. Simultaneously, the eluate from the chip was collected to quantify the amount of GelMA degraded and PVA released at various time points. The visual method was validated by comparing it with the mass-loss approach (R = 0.91), as well as the amount of GelMA eluted (R = 0.97). The degradation of the GelMA gels was also facilitated with matrix metalloproteinases 9. Notably, as the gels degraded, there was an increase in the amount of PVA released. Overall, these results support the use of the screening platform to assess hydrogel degradation and the subsequent release of entrapped therapeutic compounds.

Fabrication and Characterization of an Enzyme-Triggered, Therapeutic-Releasing Hydrogel Bandage Contact Lens Material.

PURPOSE: The purpose of this study was to develop an enzyme-triggered, therapeutic-releasing bandage contact lens material using a unique gelatin methacrylate formulation (GelMA+). METHODS: Two GelMA+ formulations, 20% w/v, and 30% w/v concentrations, were prepared through UV polymerization. The physical properties of the material, including porosity, tensile strain, and swelling ratio, were characterized. The enzymatic degradation of the material was assessed in the presence of matrix metalloproteinase-9 (MMP-9) at concentrations ranging from 0 to 300 µg/mL. Cell viability, cell growth, and cytotoxicity on the GelMA+ gels were evaluated using the AlamarBlueTM assay and the LIVE/DEADTM Viability/Cytotoxicity kit staining with immortalized human corneal epithelial cells over 5 days. For drug release analysis, the 30% w/v gels were loaded with 3 µg of bovine lactoferrin (BLF) as a model drug, and its release was examined over 5 days under various MMP-9 concentrations. RESULTS: The 30% w/v GelMA+ demonstrated higher crosslinking density, increased tensile strength, smaller pore size, and lower swelling ratio (p < 0.05). In contrast, the 20% w/v GelMA+ degraded at a significantly faster rate (p < 0.001), reaching almost complete degradation within 48 h in the presence of 300 µg/mL of MMP-9. No signs of cytotoxic effects were observed in the live/dead staining assay for either concentration after 5 days. However, the 30% w/v GelMA+ exhibited significantly higher cell viability (p < 0.05). The 30% w/v GelMA+ demonstrated sustained release of the BLF over 5 days. The release rate of BLF increased significantly with higher concentrations of MMP-9 (p < 0.001), corresponding to the degradation rate of the gels. DISCUSSION: The release of BLF from GelMA+ gels was driven by a combination of diffusion and degradation of the material by MMP-9 enzymes. This work demonstrated that a GelMA+-based material that releases a therapeutic agent can be triggered by enzymes found in the tear fluid.

In vitro-in vivo correlation of drug release profiles from medicated contact lenses using an in vitro eye blink model.

There is still a paucity of information on how in vitro release profiles from drug-loaded contact lenses (CLs) recorded in 3D printed eye models correlate with in vivo profiles. This work aims to evaluate the release profiles of two drug-loaded CLs in a 3D in vitro eye blink model and compare the obtained results with the release in a vial and the drug levels in tear fluid previously obtained from an animal in vivo study. In vitro release in the eye model was tested at two different flow rates (5 and 10 µL/min) and a blink speed of 1 blink/10 s. Model CLs were loaded with two different drugs, hydrophilic pravastatin and hydrophobic resveratrol. The release of both drugs was more sustained and lower in the 3D eye model compared to the in vitro release in vials. Interestingly, both drugs presented similar release patterns in the eye model and in vivo, although the total amount of drugs released in the eye model was significantly lower, especially for resveratrol. Strong correlations between percentages of pravastatin released in the eye model and in vivo were found. These findings suggest that the current 3D printed eye blink model could be a useful tool to measure the release of ophthalmic drugs from medicated CLs. Nevertheless, physiological parameters such as the composition of the tear fluid and eyeball surface, tear flow rates, and temperature should be optimized in further studies.

Evaluating Viscosity and Tear Breakup Time of Contemporary Commercial Ocular Lubricants on an In Vitro Eye Model.

Purpose: To evaluate the link between the viscosity of ophthalmic formulation and tear film stability using a novel in vitro eye model. Methods: The viscosities and noninvasive tear breakup time (NIKBUT) of 13 commercial ocular lubricants were measured to evaluate the correlation between viscosity and NIKBUT. The complex viscosity of each lubricant was measured three times for each angular frequency (ranging from 0.1 to 100 rad/s) using the Discovery HR-2 hybrid rheometer. The NIKBUT measurements were performed eight times for each lubricant using an advanced eye model mounted on the OCULUS Keratograph 5M. A contact lens (CL; ACUVUE OASYS [etafilcon A]) or a collagen shield (CS) was used as the simulated corneal surface. Phosphate-buffered saline was used as a simulated fluid. Results: The results showed a positive correlation between viscosity and NIKBUT at high shear rates (at 10 rad/s, r = 0.67) but not at low shear. This correlation was even better for viscosities between 0 and 100 mPa*s (r = 0.85). Most of the lubricants tested in this study also had shear-thinning properties. OPTASE INTENSE, I-DROP PUR GEL, I DROP MGD, OASIS TEARS PLUS, and I-DROP PUR had higher viscosity in comparison to other lubricants (P < 0.05). All of the formulations had a higher NIKBUT than the control (2.7 ± 1.2 seconds for CS and 5.4 ± 0.9 seconds for CL) without any lubricant (P < 0.05). I-DROP PUR GEL, OASIS TEARS PLUS, I-DROP MGD, REFRESH OPTIVE ADVANCED, and OPTASE INTENSE had the highest NIKBUT using this eye model. Conclusions: The results show that the viscosity is correlated with NIKBUT, but further work is necessary to determine the underlying mechanisms. Translational Relevance: The viscosity of ocular lubricants can affect NIKBUT and tear film stability, so it is an important property to consider when formulating ocular lubricants.

Uptake and release of polyhexamethylene biguanide (PHMB) from hydrogel and silicone hydrogel contact lenses using a radiolabel methodology.

PURPOSE: The purpose of this study was to evaluate the uptake and release of radiolabelled polyhexamethylene biguanide (PHMB) on reusable daily wear contact lenses (CLs) over 7 days. METHODS: Three silicone hydrogel (SH) contact lens materials (lotrafilcon B, balafilcon A, senofilcon A) and two conventional hydrogel (CH) materials (etafilcon A, omafilcon A) were examined. In experiment 1 (1-day study), CLs were soaked in 2 mL of phosphate buffered solution (PBS) containing radiolabelled 14C PHMB (1 µg/mL) for 8 h. The release kinetics of 14C PHMB from the CLs was measured at t = 0.25, 0.5, 1, 2, 4, 8, and 24 h in fresh 2 mL PBS. In experiment 2 (7-day study), the CLs were soaked in the 14C PHMB (1 µg/mL) solution for 8 h followed by a 16-hour release in 2 mL PBS. The lens cycle was repeated daily for 7 days. After both experiments, the residual amount of PHMB remaining within the lenses was extracted to determine the total uptake of PHMB. RESULTS: In experiment 1, the total uptake of PHMB for etafilcon A was significantly greater than senofilcon A (p = 0.01). There were no significant differences in total uptake of PHMB between other lens materials (p > 0.05). Etafilcon A released more PHMB compared to all other lens types over a 24-hr period (p < 0.001). In experiment 2, all CL materials continued to sorb more PHMB over time (p < 0.001). By day 7, the amount of PHMB sorbed by etafilcon A was significantly greater than senofilcon A (p = 0.02). After day 2, the CH materials released significantly more PHMB than the SH materials (p < 0.01). CONCLUSION: The CL materials continued to sorb PHMB with no signs of saturation after 7 days. All lens materials released a consistent amount of PHMB each day. Radioactive labelling provides a sensitive method of assessing the uptake and release of PHMB from CL materials.

Shear-Thinning and Temperature-Dependent Viscosity Relationships of Contemporary Ocular Lubricants.

PURPOSE: To evaluate the shear viscosity of contemporary, commercially available ocular lubricants at various shear rates and temperatures and to derive relevant mathematical viscosity models that are impactful for prescribing and developing eye drops to treat dry eye disease. METHODS: The shear viscosity of 12 ocular lubricants was measured using a rheometer and a temperature-controlled bath at clinically relevant temperatures at which users may experience exposure to the drops (out of the refrigerator [4.3°C]; room temperature [24.6°C]; ocular surface temperature [34.5°C]). Three replicates for each sample at each temperature were obtained using a standard volume (0.5 mL) of each sample. The viscosity of each ocular lubricant was measured over the full range of shear rates allowed by the rheometer. RESULTS: The shear viscosity of the same ocular lubricant varied significantly among the three temperatures. In general, a higher temperature resulted in smaller viscosities than a lower temperature (an average of -48% relative change from 4.3°C to 24.6°C and -21% from 24.6°C to 34.5°C). At a constant temperature, the viscosity of an ocular lubricant over the studied shear rates can be well approximated by a power-law model. CONCLUSIONS: Rheological analysis revealed that the ocular lubricants exhibited shear-thinning behavior at the measured temperatures. Differences in the ocular lubricants' formulations and measured temperatures resulted in different viscosities. TRANSLATIONAL RELEVANCE: When prescribing eye drops, eye care professionals can select the optimal one for their patients by considering a variety of factors, including its rheological property at physiologically relevant shear rates and temperatures, which can improve residence time on the ocular surface, while ensuring appropriate comfort and vision. However, care must be taken when using the derived mathematical models in this study because the in vivo shear behavior of the ocular lubricants has not been examined and might show deviations from those reported when placed on the ocular surface.

Testing drug release from medicated contact lenses: The missing link to predict in vivo performance.

Contact lenses (CLs) offer a wide variety of advantages as ocular drug-releasing platforms, but the feasibility of medicated CL development is constrained by numerous scientific, technological, and regulatory challenges. One main difficulty is the setting of release rate specifications for each drug, since at present there are no standardized in vitro release models that can appropriately predict the performance of drug-eluting CLs once placed onto the eye. CL-adapted release tests may provide knowledge on how the drug release pattern should perform in vivo to trigger and maintain the therapeutic effects for both anterior and posterior ocular tissues. Moreover, in vitro release tests are valuable tools for quality assessment during production and to investigate the effect of a change in composition or process variables. This review aims to shed light on biorelevant ways of evaluating in vitro drug release from CLs and the feasibility of establishing in vitro-in vivo correlations (IVIVC) to predict in vivo performance. First, general guidelines and Pharmacopeia release tests for topical ophthalmic formulations as well as in vitro release tests implemented for drug-CLs in the last two decades are analyzed. Then, development of an appropriate method to investigate IVIVC is attempted from the few papers simultaneously reporting in vitro release profiles and either in vivo release or therapeutic response. Finally, key points to be considered for in vitro testing drug release from a medicated CL are suggested to pave the way to the clinical arena.