Thickness scaling of ferroelectricity in BiFeO3 by tomographic atomic force microscopy.

Nanometer-scale 3D imaging of materials properties is critical for understanding equilibrium states in electronic materials, as well as for optimization of device performance and reliability, even though such capabilities remain a substantial experimental challenge. Tomographic atomic force microscopy (TAFM) is presented as a subtractive scanning probe technique for high-resolution, 3D ferroelectric property measurements. Volumetric property resolution below 315 nm3, as well as unit-cell-scale vertical material removal, are demonstrated. Specifically, TAFM is applied to investigate the size dependence of ferroelectricity in the room-temperature multiferroic BiFeO3 across two decades of thickness to below 1 nm. TAFM enables volumetric imaging of ferroelectric domains in BiFeO3 with a significant improvement in spatial resolution compared with existing domain tomography techniques. We additionally employ TAFM for direct, thickness-dependent measurements of the local spontaneous polarization and ferroelectric coercive field in BiFeO3 The thickness-resolved ferroelectric properties strongly correlate with cross-sectional transmission electron microscopy (TEM), Landau-Ginzburg-Devonshire phenomenological theory, and the semiempirical Kay-Dunn scaling law for ferroelectric coercive fields. These results provide an unambiguous determination of a stable and switchable polar state in BiFeO3 to thicknesses below 5 nm. The accuracy and utility of these findings on finite size effects in ferroelectric and multiferroic materials more broadly exemplifies the potential for novel insight into nanoscale 3D property measurements via other variations of TAFM.

Focused ion beam preparation of samples for X-ray nanotomography.

The preparation of hard material samples with the necessary size and shape is critical to successful material analysis. X-ray nanotomography requires that samples are sufficiently thin for X-rays to pass through the sample during rotation for tomography. One method for producing samples that fit the criteria for X-ray nanotomography is focused ion beam/scanning electron microscopy (FIB/SEM) which uses a focused beam of ions to selectively mill around a region of interest and then utilizes a micromanipulator to remove the milled-out sample from the bulk material and mount it on a sample holder. In this article the process for preparing X-ray nanotomography samples in multiple shapes and sizes is discussed. Additionally, solid-oxide fuel cell anode samples prepared through the FIB/SEM technique underwent volume-independence studies for multiple properties such as volume fraction, average particle size, tortuosity and contiguity to observe the characteristics of FIB/SEM samples in X-ray nanotomography.

Light-assisted synthesis of metal oxide hierarchical structures and their catalytic applications.

Short reaction times and morphology control in the synthesis of inorganic materials under nonthermal conditions remain a challenge. Herein we report a rapid, self-templating, and nonthermal method based on ultraviolet light to prepare metal oxide hierarchical structures. With this method, the morphology of the metal oxides was controlled readily without using templates.

Facile one-step template-free synthesis of uniform hollow microstructures of cryptomelane-type manganese oxide K-OMS-2.

Hollow microstructures of cryptomelane-type manganese oxide were produced in a template-free one-step process based on the fine-tuning of the oxidation rate of manganese species during the synthesis. The tuning of the reaction rate brought about by a mixture of the oxidants oxone and potassium nitrate becomes apparent from the gradual physical changes taking place in the reaction medium at early times of the synthesis. The successful synthesis of the hollow uniform structures could be performed in the ranges 120-160 degrees C and 8.2-10.7 for temperature and mass ratio oxone/potassium nitrate, respectively. Independent of the conditions of the synthesis, all of the complex microstructures showed the same pattern for the array of very long nanofibers in which some of these elongated around the surface confining the cavity and the other fibers grew normal to the surface created by the previous arrangement. A mechanism based on the heterogeneous nucleation of the cryptomelane phase on the surface of an amorphous precursor and the growth of the nanoscale fibers by processes such as dissolution-crystallization and lateral attachment of primary nanocrystalline fibers is proposed to explain the formation of the hollow structures.