Influence of electron acceptors on hexanoic acid production by Clostridium kluyveri.

Clostridium kluyveri was used for chain elongation of C2C4 fatty acids in stirred tank bioreactors. The influence of different electron acceptors (acetic acid, butyric acid and the mixture of both) on C6 fatty acid production was evaluated in presence of ethanol using similar molar alcohol/acid ratios around 3.5. Bottle batch assays without pH regulation and with only acetic acid as electron acceptor yielded a final C6 fatty acid concentration of 6.8 ±â€¯0.6 g L-1. Then, pH-regulated bioreactors were operated at constant pH of 6.8. Under such conditions, the maximum growth rate was 0.039 h-1 obtained using acetic acid and butyric acid as electron acceptors, whereas the lowest growth rate was 0.010 h-1 with only butyric acid as electron acceptor. The maximum growth rate with acetic acid only, was similar, though slightly lower, as with the mixture of C2C4 fatty acids. Besides, the maximum productions of hexanoic acid were 11.8 g L-1, 13.1 g L-1 and 21.2 g L-1 using, respectively, acetic acid, butyric acid and the mixture of both acids as electron acceptors. Thus, the use of a mixture of acetic acid and butyric acid in presence of ethanol for chain elongation, at constant pH, proved to be efficient for hexanoic acid production.

Anaerobic degradation of glycol ether-ethanol mixtures using EGSB and hybrid reactors: Performance comparison and ether cleavage pathway.

The anaerobic biodegradation of ethanol-glycol ether mixtures as 1-ethoxy-2-propanol (E2P) and 1-methoxy-2-propanol (M2P), widely used in printing facilities, was investigated by means of two laboratory-scale anaerobic bioreactors at 25oC: an expanded granular sludge bed (EGSB) reactor and an anaerobic hybrid reactor (AHR), which incorporated a packed bed to improve biomass retention. Despite AHR showed almost half of solid leakages compared to EGSB, both reactors obtained practically the same performance for the operating conditions studied with global removal efficiencies (REs) higher than 92% for organic loading rates (OLRs) as high as 54 kg of chemical oxygen demand (COD) m-3 d-1 (REs of 70% and 100% for OLRs of 10.6 and 8.3 kg COD m-3 d-1 for E2P and M2P, respectively). Identified byproducts allowed clarifying the anaerobic degradation pathways of these glycol ethers. Thus, this study shows that anaerobic scrubber can be a feasible treatment for printing emissions.

Aspen Plus process-simulation model: Producing biogas from VOC emissions in an anaerobic bioscrubber.

A process-simulation model for a novel process consisted of an anaerobic bioscrubber was developed in Aspen Plus®. A novel approach was performed to implement the anaerobic reactor in the simulation, enabling it to be connected to the scrubber. The model was calibrated and validated using data from an industrial prototype that converted air emissions polluted with volatile organic compounds with an average daily concentration of 1129 mgC Nm-3 into bioenergy for more than one year. The scrubber, which showed a removal efficiency within 83-93%, was successfully predicted with an average absolute relative error of 5.2 ±â€¯0.08% using an average height-to-theoretical-plate value of 1.05 ±â€¯0.08 m and 1.37 ±â€¯0.11 m for each of the two commercial packing materials used, respectively. The anaerobic reactor, which treated up to 24 kg of chemical oxygen demand m-3 d-1 with efficiencies of about 93%, was accurately simulated, both in effluent-stream characteristics and in the biogas stream. For example, the average absolute error between the experimental biogas production and the model values was 19.6 ±â€¯18.9%. The model proved its capability as a predictive tool and an aid in design, resulting in savings of time and money for practitioners. In addition, the approach proposed can be expanded to other bioprocesses that include unit operations.

Granulation and microbial community dynamics in the chitosan-supplemented anaerobic treatment of wastewater polluted with organic solvents.

The effect of chitosan on the development of granular sludge in upflow anaerobic sludge blanket reactors (UASB) when treating wastewater polluted with the organic solvents ethanol, ethyl acetate, and 1-ethoxy-2-propanol was evaluated. Three UASB reactors were operated for 219 days at ambient temperature with an organic loading rate (OLR) of between 0.3 kg COD m-3 d-1 and 20 kg COD m-3 d-1. One reactor was operated without the addition of chitosan, while the other two were operated with the addition of chitosan doses of 2.4 mg gVSS-1 two times. The three reactors were all able to treat the OLR tested with COD removal efficiencies greater than 90%. However, the time required to reach stable operation was considerably reduced in the chitosan-assisted reactors. The development of granules in the reactors with chitosan was accelerated and granules larger than 2000 µm were only observed in these reactors. In addition, these granules exhibited better physicochemical characteristics: the mean particle diameter (540 and 613 µm) was approximately two times greater than in the control reactor (300 µm), and the settling velocities exceeded 35 m h-1. The extracellular polymeric substances (EPS) in the reactors with the chitosan was found to be higher than in the control reactor. The protein-EPS content has been correlated with the granule size. The analyses of the microbial communities, performed through denaturing gradient gel electrophoresis and high-throughput sequencing, revealed that the syntrophic microorganisms belonging to genus Geobacter and the hydrogenotrophic methanogen Methanocorpusculum labreanum were predominant in the granules. Other methanogens like Methanosaeta species were found earlier in the chitosan-assisted reactors than in the control reactor.