Gelatin Methacryloyl (GelMA) Hydrogel Scaffolds: Predicting Physical Properties Using an Experimental Design Approach.

There is a growing interest for complex in vitro environments that closely mimic the extracellular matrix and allow cells to grow in microenvironments that are closer to the one in vivo. Protein-based matrices and especially hydrogels can answer this need, thanks to their similarity with the cell microenvironment and their ease of customization. In this study, an experimental design was conducted to study the influence of synthesis parameters on the physical properties of gelatin methacryloyl (GelMA). Temperature, ratio of methacrylic anhydride over gelatin, rate of addition, and stirring speed of the reaction were studied using a Doehlert matrix. Their impact on the following parameters was analyzed: degree of substitution, mass swelling ratio, storage modulus (log(G')), and compression modulus. This study highlights that the most impactful parameter was the ratio of methacrylic anhydride over gelatin. Although, temperature affected the degree of substitution, and methacrylic anhydride addition flow rate impacted the gel's physical properties, namely, its storage modulus and compression modulus. Moreover, this experimental design proposed a theoretical model that described the variation of GelMA's physical characteristics as a function of synthesis conditions.

Nanoliposomes from Agro-Resources as Promising Delivery Systems for Chondrocytes.

Investigations in cartilage biology have been hampered by the limited capacity of chondrocytes, especially in rats and humans, to be efficiently transfected. Liposomes are a promising delivery system due to their lipid bilayer structure similar to a biological membrane. Here we used natural rapeseed lecithin, which contains a high level of mono- and poly-unsaturated fatty acids, to evaluate the cytocompatibility of these phospholipids as future potential carriers of biomolecules in joint regenerative medicine. Results show that appropriate concentrations of nanoliposome rapeseed lecithin under 500 µg/mL were safe for chondrocytes and did not induce any alterations of their phenotype. Altogether, these results sustain that they could represent a novel natural carrier to deliver active substances into cartilage cells.

Bioactive Films Containing Alginate-Pectin Composite Microbeads with Lactococcus lactis subsp. lactis: Physicochemical Characterization and Antilisterial Activity.

Novel bioactive films were developed from the incorporation of Lactococcus lactis into polysaccharide films. Two different biopolymers were tested: cellulose derivative (hydroxylpropylmethylcellulose (HPMC)) and corn starch. Lactic acid bacteria (LAB) free or previously encapsulated in alginate-pectin composite hydrogel microbeads were added directly to the film forming solution and films were obtained by casting. In order to study the impact of the incorporation of the protective culture into the biopolymer matrix, the water vapour permeability, oxygen permeability, optical and mechanical properties of the dry films were evaluated. Furthermore, the antimicrobial effect of bioactive films against Listeria monocytogenes was studied in synthetic medium. Results showed that the addition of LAB or alginate-pectin microbeads modified slightly films optical properties. In comparison with HPMC films, starch matrix proves to be more sensitive to the addition of bacterial cells or beads. Indeed, mechanical resistance of corn starch films was lower but barrier properties were improved, certainly related to the possible establishment of interactions between alginate-pectin beads and starch. HPMC and starch films containing encapsulated bioactive culture showed a complete inhibition of listerial growth during the first five days of storage at 5 °C and a reduction of 5 logs after 12 days.

Synthesis and Characterization of Nanofunctionalized Gelatin Methacrylate Hydrogels.

Given the importance of the extracellular medium during tissue formation, it was wise to develop an artificial structure that mimics the extracellular matrix while having improved physico-chemical properties. That is why the choice was focused on gelatin methacryloyl (GelMA), an inexpensive biocompatible hydrogel. Physicochemical and mechanical properties were improved by the incorporation of nanoparticles developed from two innovative fabrication processes: High shear fluid and low frequencies/high frequencies ultrasounds. Both rapeseed nanoliposomes and nanodroplets were successfully incorporated in the GelMA networks during the photo polymerization process. The impact on polymer microstructure was investigated by Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and enzymatic degradation investigations. Mechanical stability and viscoelastic tests were conducted to demonstrate the beneficial effect of the functionalization on GelMA hydrogels. Adding nanoparticles to GelMA improved the surface properties (porosity), tuned swelling, and degradability properties. In addition, we observed that nanoemulsion didn't change significantly the mechanical properties to shear and compression solicitations, whereas nanoliposome addition decreased Young's modulus under compression solicitations. Thus, these ways of functionalization allow controlling the design of the material by choosing the type of nanoparticle (nanoliposome or nanoemulsion) in function of the application.

Nanoliposomes Permeability in a Microfluidic Drug Delivery Platform across a 3D Hydrogel.

Nanoliposomes are nano-sized vesicles that can be used as drug delivery carriers with the ability to encapsulate both hydrophobic and hydrophilic compounds. Moreover, their lipid compositions facilitate their internalization by cells. However, the interaction between nanoliposomes and the membrane barrier of the human body is not well-known. If cellular tests and animal testing offer a solution, their lack of physiological relevance and ethical concerns make them unsuitable to properly mimic human body complexity. Microfluidics, which allows the environment of the human body to be imitated in a controlled way, can fulfil this role. However, existing models are missing the presence of something that would mimic a basal membrane, often consisting of a simple cell layer on a polymer membrane. In this study, we investigated the diffusion of nanoliposomes in a microfluidic system and found the optimal parameters to maximize their diffusion. Then, we incorporated a custom made GelMA with a controlled degree of substitution and studied the passage of fluorescently labeled nanoliposomes through this barrier. Our results show that highly substituted GelMA was more porous than lower substitution GelMA. Overall, our work lays the foundation for the incorporation of a hydrogel mimicking a basal membrane on a drug delivery microfluidic platform.

Hybrid extracellular vesicles-liposome incorporated advanced bioink to deliver microRNA.

In additive manufacturing, bioink formulations govern strategies to engineer 3D living tissues that mimic the complex architectures and functions of native tissues for successful tissue regeneration. Conventional 3D-printed tissues are limited in their ability to alter the fate of laden cells. Specifically, the efficient delivery of gene expression regulators (i.e. microRNAs (miRNAs)) to cells in bioprinted tissues has remained largely elusive. In this study, we explored the inclusion of extracellular vesicles (EVs), naturally occurring nanovesicles (NVs), into bioinks to resolve this challenge. EVs show excellent biocompatibility, rapid endocytosis, and low immunogenicity, which lead to the efficient delivery of miRNAs without measurable cytotoxicity. EVs were fused with liposomes to prolong and control their release by altering their physical interaction with the bioink. Hybrid EVs-liposome (hEL) NVs were embedded in gelatin-based hydrogels to create bioinks that could efficiently encapsulate and deliver miRNAs at the target site in a controlled and sustained manner. The regulation of cells' gene expression in a 3D bioprinted matrix was achieved using the hELs-laden bioink as a precursor for excellent shape fidelity and high cell viability constructs. Novel regulatory factors-loaded bioinks will expedite the translation of new bioprinting applications in the tissue engineering field.

Biofabrication of natural hydrogels for cardiac, neural, and bone Tissue engineering Applications.

Natural hydrogels are one of the most promising biomaterials for tissue engineering applications, due to their biocompatibility, biodegradability, and extracellular matrix mimicking ability. To surpass the limitations of conventional fabrication techniques and to recapitulate the complex architecture of native tissue structure, natural hydrogels are being constructed using novel biofabrication strategies, such as textile techniques and three-dimensional bioprinting. These innovative techniques play an enormous role in the development of advanced scaffolds for various tissue engineering applications. The progress, advantages, and shortcomings of the emerging biofabrication techniques are highlighted in this review. Additionally, the novel applications of biofabricated natural hydrogels in cardiac, neural, and bone tissue engineering are discussed as well.

Physicochemical Interactions in Nanofunctionalized Alginate/GelMA IPN Hydrogels.

Polymeric hydrogels are currently at the center of research due to their particular characteristics. They have tunable physical, chemical, and biological properties making them a material of choice for a large range of applications. Polymer-composite and nanocomposite hydrogels were developed to enhance the native hydrogel's properties and to include numerous functionalities. In this work, alginate/gelatin-methacryloyl-based interpenetrating polymer network hydrogels were prepared with different alginate concentrations and investigated before and after the functionalization with nanoliposomes. The multiscale analysis was obtained through Fourier transform infrared spectroscopy and proton nuclear magnetic resonance. The results show interactions between two polymers as well as between the nanoliposomes and biopolymer.

Synthesis and characterization of C2C12-laden gelatin methacryloyl (GelMA) from marine and mammalian sources.

Gelatin methacryloyl (GelMA) is widely used for tissue engineering applications as an extracellular matrix (ECM) mimicking scaffold due to its cost-effectiveness, ease of synthesis, and high biocompatibility. GelMA is widely synthesized from porcine skin gelatin, which labors under clinical, religious, and economical restrictions. In order to overcome these limitations, GelMA can be produced from fish skin gelatin, which is eco-friendly as well. Here, we present a comparative study of the physicochemical (structural, thermal, water uptake, swelling, rheological, and mechanical) and biological (cell viability, proliferation, and spreading) properties of porcine and fish skin GelMA with low and high methacrylation degrees, before and after crosslinking, to check whether fish skin can replace porcine skin as the source of GelMA. Porcine and fish skin GelMA presented similar structural, thermal, and water uptake properties prior to crosslinking. However, subsequent to crosslinking, fish skin GelMA hydrogels exhibited a higher mass swelling ratio and a lower elastic and compressive Young's moduli than porcine skin GelMA hydrogels of similar methacrylation level. Both types of GelMA hydrogels showed great biocompatibility toward encapsulated mouse myoblast cells (C2C12), however, improved cell spreading was observed in fish skin GelMA hydrogels, and cell proliferation was only induced in low methacrylated GelMA. These results suggest that fish skin GelMA is a promising substitute for porcine skin GelMA for biomedical applications and that low methacrylated fish skin GelMA can be used as a potential scaffold for skeletal muscle tissue engineering.

Gelatin Methacryloyl (GelMA) Nanocomposite Hydrogels Embedding Bioactive Naringin Liposomes.

The development of nanocomposite hydrogels that take advantage of hierarchic building blocks is gaining increased attention due to their added functionality and numerous biomedical applications. Gathering on the unique properties of these platforms, herein we report the synthesis of bioactive nanocomposite hydrogels comprising naringin-loaded salmon-derived lecithin nanosized liposomal building blocks and gelatin methacryloyl (GelMA) macro-sized hydrogels for their embedding. This platform takes advantage of liposomes' significant drug loading capacity and their role in hydrogel network reinforcement, as well as of the injectability and light-mediated crosslinking of bioderived gelatin-based biomaterials. First, the physicochemical properties, as well as the encapsulation efficiency, release profile, and cytotoxicity of naringin-loaded nanoliposomes (LipoN) were characterized. Then, the effect of embedding LipoN in the GelMA matrix were characterized by studying the release behavior, swelling ratio, and hydrophilic character, as well as the rheological and mechanical properties of GelMA and GelMA-LipoN functionalized hydrogels. Finally, the dispersion of nanoliposomes encapsulating a model fluorescent probe in the GelMA matrix was visualized. The formulation of naringin-loaded liposomes via an optimized procedure yielded nanosized (114 nm) negatively charged particles with a high encapsulation efficiency (~99%). Naringin-loaded nanoliposomes administration to human adipose-derived stem cells confirmed their suitable cytocompatibility. Moreover, in addition to significantly extending the release of naringin from the hydrogel, the nanoliposomes inclusion in the GelMA matrix significantly increased its elastic and compressive moduli and decreased its swelling ratio, while showing an excellent dispersion in the hydrogel network. Overall, salmon-derived nanoliposomes enabled the inclusion and controlled release of pro-osteogenic bioactive molecules, as well as improved the hydrogel matrix properties, which suggests that these soft nanoparticles can play an important role in bioengineering bioactive nanocomposites for bone tissue engineering in the foreseeable future.

Soft-Nanoparticle Functionalization of Natural Hydrogels for Tissue Engineering Applications.

Tissue engineering has emerged as an important research area that provides numerous research tools for the fabrication of biologically functional constructs that can be used in drug discovery, disease modeling, and the treatment of diseased or injured organs. From a materials point of view, scaffolds have become an important part of tissue engineering activities and are usually used to form an environment supporting cellular growth, differentiation, and maturation. Among various materials used as scaffolds, hydrogels based on natural polymers are considered one of the most suitable groups of materials for creating tissue engineering scaffolds. Natural hydrogels, however, do not always provide the physicochemical and biological characteristics and properties required for optimal cell growth. This review discusses the properties and tissue engineering applications of widely used natural hydrogels. In addition, methods of modulation of their physicochemical and biological properties using soft nanoparticles as fillers or reinforcing agents are presented.

Influence of internal composition on physicochemical properties of alginate aqueous-core capsules.

HYPOTHESIS: To enhance physicochemical properties of alginate aqueous-core capsules, conventional strategies were focused in literature on designing composite and coated capsules. In the present study, own effect of liquid-core composition on mechanical and release properties was investigated. EXPERIMENTS: Capsules were prepared by dripping a CaCl2 solution into an alginate gelling solution. Viscosity of CaCl2 solution was adjusted by adding cationic, anionic and non-ionic naturally derived polymers, respectively chitosan, xanthan gum and guar gum. In parallel, uniform alginate hydrogels were prepared by different methods (pouring, in situ forming and mixing). Mechanical stability of capsules and plane hydrogels were respectively evaluated by compression experiments and small amplitude oscillatory shear rheology and then correlated. Capsules permeability was evaluated by monitoring diffusion of encapsulated cochineal dye, riboflavin and BSA. The core-shell interactions were investigated by ATR-FTIR. FINDINGS: Results showed that inner polymer had an impact on membrane stability and could act as an internal coating or provide mechanical reinforcement. Mechanical properties of alginate capsules were in a good agreement with rheological behavior of plane hydrogels. Release behavior of the entrapped molecules changed considerably. This study demonstrated the importance of aqueous-core composition, and gave new insights for possible adjusting of microcapsules physicochemical properties by modulating core-shell interactions.

Physico-chemical properties of alginate/shellac aqueous-core capsules: Influence of membrane architecture on riboflavin release.

To enhance physico-chemical properties of alginate liquid-core capsules, shellac was incorporated into the membrane (composite capsules) or as an additional external layer (coated capsules). The influence of pH, coating time, shellac concentration and preparation mechanism (acid or calcium precipitation) were investigated. Results showed that shellac significantly influenced the capsules properties. The feasibility of shellac incorporation was closely related to the preparation conditions as confirmed by Infrared spectroscopy. Optical, fluorescence and scanning electron microscopy, highlighted different capsules and membranes architectures. In contrast to simple and composite capsules, coated capsules showed a pH-dependent release of the entrapped vitamin especially after shellac crosslinking with calcium. Heating of coated capsules above the glass transition temperature investigated by Differential Scanning Calorimetry, led to irreversible structural change due to thermoplastic behavior of shellac and enhanced riboflavin retention under acidic conditions. This global approach is useful to control release mechanism of low molecular weight molecules from macro and micro-capsules.

Alginate/sodium caseinate aqueous-core capsules: a pH-responsive matrix.

HYPOTHESIS: Alginate capsules have several applications. Their functionality depends considerably on their permeability, chemical and mechanical stability. Consequently, the creation of composite system by addition of further components is expected to control mechanical and release properties of alginate capsules. EXPERIMENTS: Alginate and alginate-sodium caseinate composite liquid-core capsules were prepared by a simple extrusion. The influence of the preparation pH and sodium caseinate concentration on capsules physico-chemical properties was investigated. FINDINGS: Results showed that sodium caseinate influenced significantly capsules properties. As regards to the membrane mechanical stability, composite capsules prepared at pH below the isoelectric point of sodium caseinate exhibited the highest surface Young's modulus, increasing with protein content, explained by potential electrostatic interactions between sodium caseinate amino-groups and alginate carboxylic group. The kinetic of cochineal red A release changed significantly for composite capsules and showed a pH-responsive release. Sodium caseinate-dye mixture studied by absorbance and fluorescence spectroscopy confirmed complex formation at pH 2 by electrostatic interactions between sodium caseinate tryptophan residues and cochineal red sulfonate-groups. Consequently, the release mechanism was explained by membrane adsorption process. This global approach is useful to control release mechanism from macro and micro-capsules by incorporating guest molecules which can interact with the entrapped molecule under specific conditions.