RESUMEN
Accurate knowledge of the spatial magnetic field distribution is necessary when measuring field gradients. Therefore, a MEMS magnetic field gradiometer is reported, consisting of two identical, but independent laterally oscillating masses on a single chip. The sensor is actuated by Lorentz force and read out by modulation of the light flux passing through stationary and moving arrays of the chip. This optical readout decouples the transducer from the electronic components. Both phase and intensity are recorded which reveals information about the uniformity of the magnetic field. The magnetic flux density is measured simultaneously at two points in space and the field gradient is evaluated locally. The sensor was characterised at ambient pressure by performing frequency and magnitude response measurements with coil and various different permanent magnet arrangements, resulting in a responsivity of 35.67 V/T and detection limit of 3.07 µT/ Hz (@ 83 Hz ENBW). The sensor is compact, offers a large dynamic measurement range and can be of low-cost by using conventional MEMS batch fabrication technology.
RESUMEN
Optical cavities are of central importance in numerous areas of physics, including precision measurement, cavity optomechanics and cavity quantum electrodynamics. The miniaturisation and scaling to large numbers of sites is of interest for many of these applications, in particular for quantum computation and simulation. Here we present the first scaled microcavity system which enables the creation of large numbers of highly uniform, tunable light-matter interfaces using ions, neutral atoms or solid-state qubits. The microcavities are created by means of silicon micro-fabrication, are coupled directly to optical fibres and can be independently tuned to the chosen frequency, paving the way for arbitrarily large networks of optical microcavities.
RESUMEN
Optical resonators are essential for fundamental science, applications in sensing and metrology, particle cooling, and quantum information processing. Cavities can significantly enhance interactions between light and matter. For many applications they perform this task best if the mode confinement is tight and the photon lifetime is long. Free access to the mode center is important in the design to admit atoms, molecules, nanoparticles, or solids into the light field. Here, we demonstrate how to machine microcavity arrays of extremely high quality in pristine silicon. Etched to an almost perfect parabolic shape with a surface roughness on the level of 2 Å and coated to a finesse exceeding F = 500,000, these new devices can have lengths below 17 µm, confining the photons to 5 µm waists in a mode volume of 88λ3. Extending the cavity length to 150 µm, on the order of the radius of curvature, in a symmetric mirror configuration yields a waist smaller than 7 µm, with photon lifetimes exceeding 64 ns. Parallelized cleanroom fabrication delivers an entire microcavity array in a single process. Photolithographic precision furthermore yields alignment structures that result in mechanically robust, pre-aligned, symmetric microcavity arrays, representing a light-matter interface with unprecedented performance.
RESUMEN
Small-scale and distortion-free measurement of electric fields is crucial for applications such as surveying atmospheric electrostatic fields, lightning research, and safeguarding areas close to high-voltage power lines. A variety of measurement systems exist, the most common of which are field mills, which work by picking up the differential voltage of the measurement electrodes while periodically shielding them with a grounded electrode. However, all current approaches are either bulky, suffer from a strong temperature dependency, or severely distort the electric field requiring a well-defined surrounding and complex calibration procedures. Here we show that microelectromechanical system (MEMS) devices can be used to measure electric field strength without significant field distortion. The purely passive MEMS devices exploit the effect of electrostatic induction, which is used to generate internal forces that are converted into an optically tracked mechanical displacement of a spring-suspended seismic mass. The devices exhibit resolutions on the order of [Formula: see text] with a measurement range of up to tens of kilovolt per metre in the quasi-static regime (â² 300 Hz).We also show that it should be possible to achieve resolutions of around [Formula: see text] by fine-tuning of the sensor embodiment. These MEMS devices are compact and could easily be mass produced for wide application.
RESUMEN
The investigated ionic C60 derivative self-assembles into nanorods. When the functional side groups are removed by heating the nanorods to 623 K, they retain their shape. Utilization of lithographic markers allows the study of identical nanostructures before and after heat treatment by dynamic mode atomic force microscopy. Various independent techniques, including Raman spectroscopy and mass spectroscopy demonstrate that the shape-preserving mechanism is a thermal-stripping process, stabilizing the original supramolecular morphology. The latter implies two coherent sub-processes: detachment of the side groups and oligopolymerization running in parallel, eventually yielding rod-shaped C60 polymers. Synthesizing fullerenic polymers in this way can lead to several applications.