Polymorphism and orientation control of copper-dicarboxylate metal-organic framework thin films through vapour- and liquid-phase growth.

Precise control over the crystalline phase and crystallographic orientation within thin films of metal-organic frameworks (MOFs) is highly desirable. Here, we report a comparison of the liquid- and vapour-phase film deposition of two copper-dicarboxylate MOFs starting from an oriented metal hydroxide precursor. X-ray diffraction revealed that the vapour- or liquid-phase reaction of the linker with this precursor results in different crystalline phases, morphologies, and orientations. Pole figure analysis showed that solution-based growth of the MOFs follows the axial texture of the metal hydroxide precursor, resulting in heteroepitaxy. In contrast, the vapour-phase method results in non-epitaxial growth with uniplanar texture only.

Structural Order in Cellulose Thin Films Prepared from a Trimethylsilyl Precursor.

Biopolymer cellulose is investigated in terms of the crystallographic order within thin films. The films were prepared by spin-coating of a trimethylsilyl cellulose precursor followed by an exposure to HCl vapors; two different source materials were used. Careful precharacterization of the films was performed by infrared spectroscopy and atomic force microscopy. Subsequently, the films were investigated by grazing incidence X-ray diffraction using synchrotron radiation. The results showed broad diffraction peaks, indicating a rather short correlation length of the molecular packing in the range of a few nanometers. The analysis of the diffraction patterns was based on the known structures of crystalline cellulose, as the observed peak pattern was comparable to cellulose phase II and phase III. The dominant fraction of the film is formed by two different types of layers, which are oriented parallel to the substrate surface. The stacking of the layers results in a one-dimensional crystallographic order with a defined interlayer distance of either 7.3 or 4.2 Å. As a consequence, two different preferred orientations of the polymer chains are observed. In both cases, polymer chain axes are aligned parallel to the substrate surface, and the orientation of the cellulose molecules are concluded to be either edge-on or flat-on. A minor fraction of the cellulose molecules form nanocrystals that are randomly distributed within the films. In this case, the molecular packing density was found to be smaller in comparison to the known crystalline phases of cellulose.

Substrate-Induced Phase of a Benzothiophene Derivative Detected by Mid-Infrared and Lattice Phonon Raman Spectroscopy.

The presence of a substrate-induced polymorph of 2,7-dioctyloxy[1]benzothieno[3,2-b]benzothiophene is probed in microscopic crystals and in thin films. Two experimental techniques are used: lattice phonon Raman and IR spectroscopy. The bulk crystal and substrate-induced phase have an entirely different molecular packing, and therefore, their Raman spectra are characteristic fingerprints of the respective polymorphs. These spectra can be unambiguously assigned to the individual polymorphs. Drop-cast and spin-coated thin films on solid substrates are investigated in the as-prepared state and after solvent-vapor annealing. Because Raman spectroscopy is less sensitive with decreasing film thickness, IR spectroscopy is shown to be a more feasible tool for phase detection. The surface-induced phase is mainly present in the as-prepared thin films, whereas the bulk phase is present after solvent-vapor annealing. This result suggests that the surface-induced phase is a metastable polymorph.

Impact of sample misalignment on grazing incidence x-ray diffraction patterns and the resulting unit cell determination.

Grazing incidence x-ray diffraction (GIXD) is a frequently used tool for the crystallographic characterization of thin films in terms of polymorph identification and determination of the crystallographic lattice parameters. Even full structure solutions are possible. To obtain highly accurate diffraction patterns, the thin film sample has to be aligned carefully with the center of the goniometer, which allows a defined incidence of the primary x-ray beam relative to the sample surface. This work studies the effect of misalignment of a thin film sample on the acquired diffraction pattern. Three potential types of misalignments are considered: the deviation of the sample surface from the center of the goniometer, an error in the incidence angle of the primary beam, and an inclination of the goniometer rotation axis from the normal of the substrate surface. The consequence of these types of sample misalignments is the shift of diffraction peaks toward specific directions in reciprocal space. Mathematical equations are given that relate the error in positions of Bragg peaks for each type of sample misalignment. Experiments with intentionally misaligned samples confirm the given formulas. In a subsequent step, the errors in the peak positions are translated to systematic errors in the estimation of the unit cell parameters. Depending on the type of misalignment, some alignment errors can be reduced or even corrected; in particular, azimuthal sample rotations prove to be advantageous in these cases. The results in this work improve the quality of GIXD measurements, in general, enabling deeper analysis like the full structure solution from the GIXD pattern on everyday basis.

Searching for New Polymorphs by Epitaxial Growth.

The formation of unknown polymorphs due to the crystallization at a substrate surface is frequently observed. This phenomenon is much less studied for epitaxially grown molecular crystals since the unambiguous proof of a new polymorph is a challenging task. The existence of multiple epitaxial alignments of the crystallites together with the simultaneous presence of different polymorphs does not allow simple phase identification. We present grazing incidence X-ray diffraction studies on conjugated molecules like perylenetetracarboxylic dianhydride (PTCDA), pentacene, dibenzopentacene (trans-DBPen), and dicyanovinylquater-thiophene (DCV4T-Et2) grown by physical vapor deposition on single crystalline surfaces like Ag(111), Cu(111), and graphene. A new method for indexing the observed Bragg peaks allows the determination of the crystallographic unit cells so that the type of crystallographic phase can be clearly identified. This approach even works when several polymorphs are simultaneously present within a single sample as shown for DCV4T-Et2 on Ag(111). Additionally, epitaxial relationships between the epitaxially grown crystallites and the single crystalline surfaces are determined. In a subsequent step, the experimental data are used for the crystal structure solution of an unknown polymorph, as shown for the example trans-DBPen grown on Cu(111).

An efficient method for indexing grazing-incidence X-ray diffraction data of epitaxially grown thin films.

Crystal structure identification of thin organic films entails a number of technical and methodological challenges. In particular, if molecular crystals are epitaxially grown on single-crystalline substrates a complex scenario of multiple preferred orientations of the adsorbate, several symmetry-related in-plane alignments and the occurrence of unknown polymorphs is frequently observed. In theory, the parameters of the reduced unit cell and its orientation can simply be obtained from the matrix of three linearly independent reciprocal-space vectors. However, if the sample exhibits unit cells in various orientations and/or with different lattice parameters, it is necessary to assign all experimentally obtained reflections to their associated individual origin. In the present work, an effective algorithm is described to accomplish this task in order to determine the unit-cell parameters of complex systems comprising different orientations and polymorphs. This method is applied to a polycrystalline thin film of the conjugated organic material 6,13-pentacenequinone (PQ) epitaxially grown on an Ag(111) surface. All reciprocal vectors can be allocated to unit cells of the same lattice constants but grown in various orientations [sixfold rotational symmetry for the contact planes (102) and (102)]. The as-determined unit cell is identical to that reported in a previous study determined for a fibre-textured PQ film. Preliminary results further indicate that the algorithm is especially effective in analysing epitaxially grown crystallites not only for various orientations, but also if different polymorphs are present in the film.

Indexing grazing-incidence X-ray diffraction patterns of thin films: lattices of higher symmetry.

Grazing-incidence X-ray diffraction studies on organic thin films are often performed on systems showing fibre-textured growth. However, indexing their experimental diffraction patterns is generally challenging, especially if low-symmetry lattices are involved. Recently, analytical mathematical expressions for indexing experimental diffraction patterns of triclinic lattices were provided. In the present work, the corresponding formalism for crystal lattices of higher symmetry is given and procedures for applying these equations for indexing experimental data are described. Two examples are presented to demonstrate the feasibility of the indexing method. For layered crystals of the prototypical organic semiconductors di-indeno-perylene and (ortho-di-fluoro)-sexi-phenyl, as grown on highly oriented pyrolytic graphite, their yet unknown unit-cell parameters are determined and their crystallographic lattices are identified as monoclinic and orthorhombic, respectively.

Polarized Raman spectroscopy to elucidate the texture of synthesized MoS2.

Texture has a significant impact on several key properties of transition-metal dichalcogenides (TMDs) films. Films with in-plane oriented grains have been successfully implemented in nano- and opto-electronic devices, whereas, films with out-of-plane oriented material have shown excellent performance in catalytic applications. It will be demonstrated that the texture of nanocrystalline TMD films can be determined with polarized Raman spectroscopy. A model describing the impact of texture on the Raman response of 2D-TMDs will be presented. For the specific case of MoS2, the model was used to quantify the impact of texture on the relative strength of the A1g and E12g modes in both the unpolarized and polarized Raman configuration. Subsequently, the capability to characterize texture by polarized Raman was demonstrated on various MoS2 films grown by atomic-layer deposition (ALD) and validated by complementary transmission electron microscopy (TEM) and synchrotron based 2D grazing-incidence X-ray diffraction (GIXD) measurements. This also revealed how the texture evolved during ALD growth of MoS2 and subsequent annealing of the films. The insights presented in this work allow a deeper understanding of Raman spectra of nanocrystalline TMDs and enable a rapid and non-destructive method to probe texture.

In Situ Formation of TiB2 in Fe-B System with Titanium Addition and Its Influence on Phase Composition, Sintering Process and Mechanical Properties.

Interaction of iron and boron at elevated temperatures results in the formation of an E (Fe + Fe2B) eutectic phase that plays a great role in enhancing mass transport phenomena during thermal annealing and therefore in the densification of sintered compacts. When cooled down, this phase solidifies as interconnected hard and brittle material consisting of a continuous network of Fe2B borides formed at the grain boundaries. To increase ductile behaviour, a change in precipitates' stoichiometry was investigated by partially replacing iron borides by titanium borides. The powder of elemental titanium was introduced to blend of iron and boron powders in order to induce TiB2 in situ formation. Titanium addition influence on microstructure, phase composition, density and mechanical properties was investigated. The observations were supported with thermodynamic calculations. The change in phase composition was analysed by means of dilatometry and X-ray diffraction (XRD) coupled with thermodynamic calculations.

GIDVis: a comprehensive software tool for geometry-independent grazing-incidence X-ray diffraction data analysis and pole-figure calculations.

GIDVis is a software package based on MATLAB specialized for, but not limited to, the visualization and analysis of grazing-incidence thin-film X-ray diffraction data obtained during sample rotation around the surface normal. GIDVis allows the user to perform detector calibration, data stitching, intensity corrections, standard data evaluation (e.g. cuts and integrations along specific reciprocal-space directions), crystal phase analysis etc. To take full advantage of the measured data in the case of sample rotation, pole figures can easily be calculated from the experimental data for any value of the scattering angle covered. As an example, GIDVis is applied to phase analysis and the evaluation of the epitaxial alignment of pentacene-quinone crystallites on a single-crystalline Au(111) surface.

Surface Induced Phenytoin Polymorph. 2. Structure Validation by Comparing Experimental and Density Functional Theory Raman Spectra.

A method for structure solution in thin films that combines grazing incidence X-ray diffraction data analysis and crystal structure prediction was presented in a recent work (Braun et al. Cryst. Growth Des.2019, DOI: 10.1021/acs.cgd.9b00857). Applied to phenytoin form II, which is only detected in films, the approach gave a very reasonable, but not fully confirmed, candidate structure with Z = 4 and Z' = 2. In the present work, we demonstrate how, by calculating and measuring the crystal Raman spectrum in the low wavenumber energy region with the aim of validating the candidate structure, this can be further refined. In fact, we find it to correspond to a saddle point of the energy landscape of the system, from which a minimum of lower symmetry may be reached. With the new structure, with Z = 4 and Z' = 2, we finally obtain an excellent agreement between experimental and calculated Raman spectra.

Surface Induced Phenytoin Polymorph. 1. Full Structure Solution by Combining Grazing Incidence X-ray Diffraction and Crystal Structure Prediction.

Understanding the behavior and properties of molecules assembled in thin layers requires knowledge of their crystalline packing. The drug phenytoin (5,5-diphenylhydantoin) is one of the compounds that can be grown as a surface induced polymorph. By using grazing incidence X-ray diffraction, the monoclinic unit cell of the new form II can be determined, but, due to crystal size and the low amount of data, a full solution using conventional structure solving strategies fails. In this work, the full solution has been obtained by combining computational structure generation and experimental results. The comparison between the bulk and the new surface induced phase reveals significant packing differences of the hydrogen-bonding network, which might be the reason for the faster dissolution of form II with respect to form I. The results are very satisfactory, and the method might be adapted for other systems, where, due to the limited amount of experimental data, one must rely on additional approaches to gain access to more detailed information to understand the solid-state behavior.

Vapour-phase deposition of oriented copper dicarboxylate metal-organic framework thin films.

Copper dicarboxylate metal-organic framework films are deposited via chemical vapour deposition. Uniform films of CuBDC and CuCDC with an out-of-plane orientation and accessible porosity are obtained from the reaction of Cu and CuO with vaporised dicarboxylic acid linkers.

Indexing of grazing-incidence X-ray diffraction patterns: the case of fibre-textured thin films.

Crystal structure solutions from thin films are often performed by grazing-incidence X-ray diffraction (GIXD) experiments. In particular, on isotropic substrates the thin film crystallites grow in a fibre texture showing a well defined crystallographic plane oriented parallel to the substrate surface with random in-plane order of the microcrystallites forming the film. In the present work, analytical mathematical expressions are derived for indexing experimental diffraction patterns, a highly challenging task which hitherto mainly relied on trial-and-error approaches. The six lattice constants a, b, c, α, ß and γ of the crystallographic unit cell are thereby determined, as well as the rotation parameters due to the unknown preferred orientation of the crystals with respect to the substrate surface. The mathematical analysis exploits a combination of GIXD data and information acquired by the specular X-ray diffraction. The presence of a sole specular diffraction peak series reveals fibre-textured growth with a crystallographic plane parallel to the substrate, which allows establishment of the Miller indices u, v and w as the rotation parameters. Mathematical expressions are derived which reduce the system of unknown parameters from the three- to the two-dimensional space. Thus, in the first part of the indexing routine, the integers u and v as well as the Laue indices h and k of the experimentally observed diffraction peaks are assigned by systematically varying the integer variables, and by calculating the three lattice parameters a, b and γ. Because of the symmetry of the derived equations, determining the missing parameters then becomes feasible: (i) w of the surface parallel plane, (ii) the Laue indices l of the diffraction peak and (iii) analogously the lattice constants c, α and ß. In a subsequent step, the reduced unit-cell geometry can be identified. Finally, the methodology is demonstrated by application to an example, indexing the diffraction pattern of a thin film of the organic semiconductor pentacenequinone grown on the (0001) surface of highly oriented pyrolytic graphite. The preferred orientation of the crystallites, the lattice constants of the triclinic unit cell and finally, by molecular modelling, the full crystal structure solution of the as-yet-unknown polymorph of pentacenequinone are determined.

Solvent Vapor Annealing of Amorphous Carbamazepine Films for Fast Polymorph Screening and Dissolution Alteration.

Solubility enhancement and thus higher bioavailability are of great importance and a constant challenge in pharmaceutical research whereby polymorph screening and selection is one of the most important tasks. A very promising approach for polymorph screening is solvent vapor annealing where a sample is exposed to an atmosphere saturated with molecules of a specific chemical/solvent. In this work, amorphous carbamazepine thin films were prepared by spin coating, and the transformation into crystalline forms under exposure to solvent vapors was investigated. Employing grazing incidence X-ray diffraction, four distinct carbamazepine polymorphs, a solvate, and hydrates could be identified, while optical microscopy showed mainly spherulitic morphologies. In vitro dissolution experiments revealed different carbamazepine release from the various thin-film samples containing distinct polymorphic compositions: heat treatment of amorphous samples at 80 °C results in an immediate release; samples exposed to EtOH vapors show a drug release about 5 times slower than this immediate one; and all the others had intermediate release profiles. Noteworthy, even the sample of slowest release has a manifold faster release compared to a standard powder sample demonstrating the capabilities of thin-film preparation for faster drug release in general. Despite the small number of samples in this screening experiment, the results clearly show how solvent vapor annealing can assist in identifying potential polymorphs and allows for estimating their impact on properties like bioavailability.

DFT-Assisted Polymorph Identification from Lattice Raman Fingerprinting.

A combined experimental and theoretical approach, consisting of lattice phonon Raman spectroscopy and density functional theory (DFT) calculations, is proposed as a tool for lattice dynamics characterization and polymorph phase identification. To illustrate the reliability of the method, the lattice phonon Raman spectra of two polymorphs of the molecule 2,7-dioctyloxy[1]benzothieno[3,2-b]benzothiophene are investigated. We show that DFT calculations of the lattice vibrations based on the known crystal structures, including many-body dispersion van der Waals (MBD-vdW) corrections, predict experimental data within an accuracy of ≪5 cm-1 (≪0.6 meV). Due to the high accuracy of the simulations, they can be used to unambiguously identify different polymorphs and to characterize the nature of the lattice vibrations and their relationship to the structural properties. More generally, this work implies that DFT-MBD-vdW is a promising method to describe also other physical properties that depend on lattice dynamics like charge transport.