Deposition of Ultrathin MgB2 Films from a Suspension Using Cosolvent Marangoni Flow.

Magnesium diboride (MgB2) has demonstrated, theoretically and experimentally, promise as a candidate material for hydrogen storage and has thus attracted much contemporary research interest. To study hydrogen gas adsorption on MgB2 thin films using a quartz crystal microbalance (QCM)─a workhorse apparatus for this specific experiment─MgB2 must be deposited uniformly on the active surface of the QCM without damaging the quartz's performance. In work presented here, a wet-chemistry colloid synthesis and deposition process of a MgB2 thin film on a gold (Au) surface was established to avoid the extreme conditions of conventional physical deposition methods. This process also counteracts the unwanted phenomena of drying droplets on a solid surface, particularly the coffee-ring effect. To verify the normal function of the QCM after MgB2 deposition and its ability to obtain meaningful data, simple gas adsorption tests were conducted on the QCM, and the MgB2 film on the QCM was characterized with X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) for elemental analysis and surface roughness, respectively. To obtain information about the thickness and the involvement of the coffee-ring effect, the same synthesis route was applied on a similar gold substrate─an evaporated Au film on glass. XPS characterization of the film and its precursor suspension shows the potential existence of both MgB2 and its oxide forms. The film's thickness on evaporated Au was measured by scanning transmission electron microscopy (STEM) to be 3.9 nm. The resulting samples show mitigation of the coffee-ring effect through roughness measurements with AFM at two scan sizes of 50 × 50 and 1 × 1 µm2.

Kinetic Enhancement of Direct Hydrogenation of MgB2 to Mg(BH4 )2 upon Mechanical Milling with THF, MgH2 , and/or Mg.

Modification of magnesium diboride, MgB2 , by mechanical milling with THF, MgH2 , and/or Mg results in a lowering of the conditions required for its direct, bulk hydrogenation to magnesium borohydride, Mg(BH4 )2 , by 300 bar and 100 °C. Following mechanical milling with MgH2 or THF and Mg, MgB2 can be hydrogenated to Mg(BH4 )2 at 300 °C under 700 bar of H2 while achieving ∼54-71 % conversion to the borohydride. The discovery of a means of dramatically lowering the conditions required for the hydrogenation of MgB2 is an important step towards the development of a practical onboard hydrogen storage system based on hydrogen cycling between Mg(BH4 )2 and MgB2 . We suggest that mechano-milling with THF, Mg, and/or MgH2 may possibly introduce defects in the MgB2 structure which enhance hydrogenation. The ability to activate the MgB2 through the introduction of structural defects transcends its relevance to hydrogen storage, as a method of overcoming its chemical inertness provides the key to harnessing other interesting properties of this material.

Fe4(OAc)10[EMIM]2: Novel Iron-Based Acetate EMIM Ionic Compound.

We synthesized and characterized a novel iron(II) aceto EMIM coordination compound, which has a simplified empirical formula Fe4(OAc)10[EMIM]2, in two different hydration forms: as anhydrous monoclinic compound and triclinic dihydrate Fe4(OAc)10[EMIM]2·2H2O. The dihydrate compound is isostructural with recently reported Mn4(OAc)10[EMIM]2·2H2O, while the anhydrate is a superstructure of the Mn counterpart, suggesting the existence of solid solutions. Both new Fe compounds contain chains of Fe2+ octahedrally coordinated exclusively by acetate groups. The EMIM moieties do not interact directly with the Fe2+ and contribute to the structural framework of the compound through van der Waals forces and C-H···O hydrogen bonds with the acetate anions. The compounds have a melting temperature of ∼94 °C; therefore, they can be considered metal-containing ionic liquids. Differential thermal analysis indicates three endothermic transitions associated with melting, structural rearrangement in the molten state at about 157 °C, and finally, thermal decomposition of the Fe4(OAc)10[EMIM]2. Thermogravimetric analyses indicate an ∼72 wt % mass loss during the decomposition at 280-325 °C. The Fe4(OAc)10[EMIM]2 compounds have higher thermal stability than their Mn counterparts and [EMIM][OAc] but lower compared to iron(II) acetate. Temperature-programmed desorption coupled with mass spectrometry shows that the decomposition pathway of the Fe4(OAc)10[EMIM]2 involves four distinct regimes with peak temperatures at 88, 200, 267, and 345 °C. The main species observed in the decomposition of the compound are CH3, H2O, N2, CO, OC-CH3, OH-CO, H3C-CO-CH3, and H3C-O-CO-CH3. Variable-temperature infrared vibrational spectroscopy indicates that the phase transition at 160-180 °C is associated with a reorientation of the acetate ions, which may lead to a lower interaction with the [EMIM]+ before the decomposition of the Fe4(OAc)10[EMIM]2 upon further heating. The Fe4(OAc)10[EMIM]2 compounds are porous, plausibly capable of accommodating other types of molecules.

Synthesis, Characterization, and Crystal Structures of Two New Manganese Aceto EMIM Ionic Compounds with Chains of Mn2+ Ions Coordinated Exclusively by Acetate.

We synthesized and determined crystal structures of two manganese(II) aceto EMIM coordination compounds with simplified empirical formulas Mn4(OAc)10[EMIM]2 and Mn4(OAc)10[EMIM]2·2H2O. Both compounds feature extended chains of Mn2+ octahedrally coordinated exclusively by acetate anions, which has been observed for the first time. The EMIM moieties and water molecules participate in hydrogen bonding with acetate anions but do not directly interact with the metal cation. Both compounds have melting temperatures around 120 °C and can be considered as (non-room-temperature) ionic liquids. The structural arrangement represented by the two title compounds is robust in terms of accommodating other types of cations and allows for tuning of physical properties of the ionic liquid by means of cation substitution. Thermal analysis results obtained using TGA-DSC and VT IR suggest melting phase transitions around 120 °C, followed by structural rearrangement in the molten state taking place around 140-160 °C. Compounds I and II have a higher thermal stability range compared to [EMIM][OAc] ionic liquid, with an onset decomposition temperature above 260 °C.

LiSc(BH4)4: a novel salt of Li+ and discrete Sc(BH4)4(-) complex anions.

LiSc(BH4)4 has been prepared by ball milling of LiBH4 and ScCl3. Vibrational spectroscopy indicates the presence of discrete Sc(BH4)4(-) ions. DFT calculations of this isolated complex ion confirm that it is a stable complex, and the calculated vibrational spectra agree well with the experimental ones. The four BH4(-) groups are oriented with a tilted plane of three hydrogen atoms directed to the central Sc ion, resulting in a global 8 + 4 coordination. The crystal structure obtained by high-resolution synchrotron powder diffraction reveals a tetragonal unit cell with a = 6.076 A and c = 12.034 A (space group P-42c). The local structure of the Sc(BH4)4(-) complex is refined as a distorted form of the theoretical structure. The Li ions are found to be disordered along the z axis.

Bio-oil extraction of Jatropha curcas with ionic liquid co-solvent: Fate of biomass protein.

The fate of oil-seed biomass protein has been tracked through all steps of a multi-phase extraction process using an ionic liquid based co-solvent system previously demonstrated to extract bio-oil and phorbol esters and to recover fermentable sugars from Jatropha oil seed. These analyses, however, did not address the fate of biomass protein. This work demonstrated that the majority of protein (∼86%) tracked with the biomass with the balance lost to co-solvent (∼12%) and methanol (∼2%) washes. A significant portion of the ionic liquid remained with the treated biomass and required aggressive methanol washes to recover. A system analysis showed a net-positive energy balance and thus the potential of this system to produce both bio-oil and protein-rich toxin-free biomass. While these results further support Jatropha as an oil seed crop, the additional costs of solvent recovery will need to be addressed if commercialization is to be realized.

Rapid Fabrication of Graphene Field-Effect Transistors with Liquid-metal Interconnects and Electrolytic Gate Dielectric Made of Honey.

Historically, graphene-based transistor fabrication has been time-consuming due to the high demand for carefully controlled Raman spectroscopy, physical vapor deposition, and lift-off processes. For the first time in a three-terminal graphene field-effect transistor embodiment, we introduce a rapid fabrication technique that implements non-toxic eutectic liquid-metal Galinstan interconnects and an electrolytic gate dielectric comprised of honey. The goal is to minimize cost and turnaround time between fabrication runs; thereby, allowing researchers to focus on the characterization of graphene phenomena that drives innovation rather than a lengthy device fabrication process that hinders it. We demonstrate characteristic Dirac peaks for a single-gate graphene field-effect transistor embodiment that exhibits hole and electron mobilities of 213 ± 15 and 166 ± 5 cm 2/V·s respectively. We discuss how our methods can be used for the rapid determination of graphene quality and can complement Raman Spectroscopy techniques. Lastly, we explore a PN junction embodiment which further validates that our fabrication techniques can rapidly adapt to alternative device architectures and greatly broaden the research applicability.

Corecovery of lipids and fermentable sugars from Rhodosporidium toruloides using ionic liquid cosolvents: application of recycle to batch fermentation.

This work evaluates the ability of an ionic liquid-methanol cosolvent system to extract lipids and recycle fermentable sugars recovered from oil-bearing Rhodosporidium toruloides grown in batch culture on defined media using glucose and xylose as carbon sources. Growth on the recycled mixed carbon substrate was successful with glucose consumed before xylose and overall cell mass to lipid yields (YP/X ) between 57% and 61% (w/w relative to whole dried cell mass) achieved. Enzymatic hydrolysis of the delipified carbohydrate fraction recovered approximately 9%-11% (w/w) of the whole dried cell mass as fermentable sugars, which were successfully recycled as carbon sources without further purification. In total, up to 70% (w/w) of the whole dried cell mass was recovered as lipids and fermentable sugars and the substrate to lipid yields (YP/S ) was increased from 0.12 to 0.16 g lipid/g carbohydrate consumed, highlighting the promise of this approach to process lipid bearing cell biomass.

Direct hydrogenation of magnesium boride to magnesium borohydride: demonstration of >11 weight percent reversible hydrogen storage.

Conditions have been found whereby it is possible to reversibly store >11 wt% hydrogen through the direct hydrogenation of MgB(2) to Mg(BH(4))(2).