RESUMEN
The exploration of cathode and anode materials that enable reversible storage of mono and multivalent cations has driven extensive research on organic compounds. In this regard, polyimide (PI)-based electrodes have emerged as a promising avenue for the development of post-lithium energy storage systems. This review article provides a comprehensive summary of the syntheses, characterizations, and applications of PI compounds as electrode materials capable of hosting a wide range of cations. Furthermore, the review also delves into the advancements in PI based solid state batteries, PI-based separators, current collectors, and their effectiveness as polymeric binders. By highlighting the key findings in these areas, this review aims at contributing to the understanding and advancement of PI-based structures paving the way for the next generation of energy storage systems.
RESUMEN
The goal of limiting global warming to 1.5 °C requires a drastic reduction in CO2 emissions across many sectors of the world economy. Batteries are vital to this endeavor, whether used in electric vehicles, to store renewable electricity, or in aviation. Present lithium-ion technologies are preparing the public for this inevitable change, but their maximum theoretical specific capacity presents a limitation. Their high cost is another concern for commercial viability. Metal-air batteries have the highest theoretical energy density of all possible secondary battery technologies and could yield step changes in energy storage, if their practical difficulties could be overcome. The scope of this review is to provide an objective, comprehensive, and authoritative assessment of the intensive work invested in nonaqueous rechargeable metal-air batteries over the past few years, which identified the key problems and guides directions to solve them. We focus primarily on the challenges and outlook for Li-O2 cells but include Na-O2, K-O2, and Mg-O2 cells for comparison. Our review highlights the interdisciplinary nature of this field that involves a combination of materials chemistry, electrochemistry, computation, microscopy, spectroscopy, and surface science. The mechanisms of O2 reduction and evolution are considered in the light of recent findings, along with developments in positive and negative electrodes, electrolytes, electrocatalysis on surfaces and in solution, and the degradative effect of singlet oxygen, which is typically formed in Li-O2 cells.
RESUMEN
Block copolymer electrolytes (BCE) such as polystyrene-block-poly(ethylene oxide) (SEO) blended with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and composed of mechanically robust insulating and rubbery conducting nanodomains are promising solid-state electrolytes for Li batteries. Here, we compare ionic solvation, association, distribution, and conductivity in SEO-LiTFSI BCEs and their homopolymer PEO-LiTFSI analogs toward a fundamental understanding of the maximum in conductivity and transport mechanisms as a function of salt concentration. Ionic conductivity measurements reveal that SEO-LiTFSI and PEO-LiTFSI exhibit similar behaviors up to a Li/EO ratio of 1/12, where roughly half of the available solvation sites in the system are filled, and conductivity is maximized. As the Li/EO ratios increase to 1/5 the conductivity, of the PEO-LiTFSI drops nearly 3-fold, while the conductivity of SEO-LiTFSI remains constant. FTIR spectroscopy reveals that additional Li cations in the homopolymer electrolyte are complexed by additional EO units when the Li/EO ratio exceeds 1/12, while in the BCE, the proportion of complexed and uncomplexed EO units remains constant; Raman spectroscopy data at the same concentrations show that Li cations in the SEO-LiTFSI samples tend to coordinate more to their counteranions. Atomistic-scale molecular dynamics simulations corroborate these results and further show that associated ions tend to segregate to the SEO-LiTFSI domain interfaces. The opportunity for "excess" salt to be sequestered at BCE interfaces results in the retention of an optimum ratio of uncompleted and complexed PEO solvation sites in the middle of the conductive nanodomains of the BCE and maximized conductivity over a broad range of salt concentrations.
RESUMEN
In this study, we present a new aprotic solvent, 2,4-dimethoxy-2,4-dimethylpentan-3-one (DMDMP), which is designed to resist nucleophilic attack and hydrogen abstraction by reduced oxygen species. Li-O2 cells using DMDMP solutions were successfully cycled. By various analytical measurements, we showed that even after prolonged cycling only a negligible amount of DMDMP was degraded. We suggest that the observed capacity fading of the Li-O2 DMDMP-based cells was due to instability of the lithium anode during cycling. The stability toward oxygen species makes DMDMP an excellent solvent candidate for many kinds of electrochemical systems which involve oxygen reduction and assorted evaluation reactions.
RESUMEN
The growing demand for energy has increased the need for battery storage, with lithium-ion batteries being widely used. Among those, nickel-rich layered lithium transition metal oxides [LiNi1-x-yCoxMnyO2 NCM (1 - x - y > 0.5)] are some of the promising cathode materials due to their high specific capacities and working voltages. In this study, we demonstrate that a thin, simple coating of polyalanine chiral molecules improves the performance of Ni-rich cathodes. The chiral organic coating of the active material enhances the discharge capacity and rate capability. Specifically, NCM811 and NCM622 electrodes coated with chiral molecules exhibit lower voltage hysteresis and better rate performance, with a capacity improvement of >10% at a 4 C discharge rate and an average improvement of 6%. We relate these results to the chirally induced spin selectivity effect that enables us to reduce the resistance of the electrode interface and to reduce dramatically the overpotential needed for the chemical process by aligning the electron spins.
RESUMEN
A critical current challenge in the development of all-solid-state lithium batteries (ASSLBs) is reducing the cost of fabrication without compromising the performance. Here we report a sulfide ASSLB based on a high-energy, Co-free LiNiO2 cathode with a robust outside-in structure. This promising cathode is enabled by the high-pressure O2 synthesis and subsequent atomic layer deposition of a unique ultrathin LixAlyZnzOδ protective layer comprising a LixAlyZnzOδ surface coating region and an Al and Zn near-surface doping region. This high-quality artificial interphase enhances the structural stability and interfacial dynamics of the cathode as it mitigates the contact loss and continuous side reactions at the cathode/solid electrolyte interface. As a result, our ASSLBs exhibit a high areal capacity (4.65 mAh cm-2), a high specific cathode capacity (203 mAh g-1), superior cycling stability (92% capacity retention after 200 cycles) and a good rate capability (93 mAh g-1 at 2C). This work also offers mechanistic insights into how to break through the limitation of using expensive cathodes (for example, Co-based) and coatings (for example, Nb-, Ta-, La- or Zr-based) while still achieving a high-energy ASSLB performance.
RESUMEN
Modifying the surfaces of zinc and other metallic substrates is considered an effective strategy to enhance the reversibility of the zinc deposition and stripping processes. While a variety of surface modification strategies have been explored, their ability to be practically implemented is not always trivial due to the associated high costs and complexity of the proposed techniques. In this study, we showcase a straightforward method for preparing ultrathin polyelectrolyte coatings using polydiallyldimethylammonium chloride (PDDA) and polyethylenimine (PEI). The coatings, characterized by their electrostatic charge and hydrophobicity, suppress side reactions and even out the electrodeposition process across the substrate surface. The PDDA-coated anodes demonstrate significantly reduced voltage hysteresis, uniform zinc morphology, improved self-discharge rates, and an impressive Coulombic efficiency exceeding 99% over prolonged cycling. Our findings highlight the potential that such cost-effective and straightforward surface treatments could be widely applied in Zn metal-based batteries.
RESUMEN
The design of electrolyte solutions that permit reversible and efficient Mg metal electrodeposition is one of the most important tasks in the development of rechargeable Mg batteries. Several types of electrolyte solutions for Mg metal anodes have been developed and explored over the last two decades. These investigations have contributed to a better understanding of the Mg deposition and stripping processes. However, the Coulombic efficiency (CE) for reversible electrodeposition reported for these various systems and their performance in comparison to one another remained unclear. We used rigorous electrochemical methods to accurately quantify the average CE of the major electrolyte solutions considered for secondary Mg metal batteries. We demonstrated how changes in the experiential protocols influence CE measurements, resulting in inconsistent reports. Even though exceptional efficiency has been reported for a variety of systems, we discovered that the only candidate that currently meets the 99% CE benchmark during a prolonged cycling procedure is the dichloro-complex, which is a first-generation Grignard-based electrolyte solution. Second- and third-generation Grignard-free and chloride-free solutions showed reasonable CE only when the deposition currents densities were lowered. This comprehensive and systematic investigation will help to create a more accurate treasure map for potential electrolyte solutions for rechargeable Mg metal anodes.
RESUMEN
The optimal performance of organic electrodes for aqueous batteries requires their full compatibility with selected electrolyte solutions. Electrode materials having 1-3-dimensional structures of variable rigidity possess a confined space in their structure filled with water and electrolyte solutions. Depending on the rigidity and confined space geometry, insertion and extraction of ions into electrode structures are often coupled with incorporation/withdrawal of water molecules. Aside from the scientific interest in understanding the charging mechanism of such systems, co-insertion of solvent molecules affects strongly the charge storage capability of the electrodes for energy storage devices. We present herein in situ electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D) investigations of polyaniline (PANI) electrodes operating in various aqueous Na+-containing electrolytes, namely, Na2SO4, NaClO4, NaBF4, and NaPF6. Careful analysis of the EQCM-D results provides a dynamic snapshot of the mixed anionic/protonic fluxes and the accompanying water molecules' insertion/extraction to/from the PANI electrodes. Based on our observations, it was found that the charging mechanism, as well as the capacity values, strictly depends on the electrolyte pH, the chaotropic/kosmotropic character of the anionic dopants, and the amount of the extracted water molecules. This study demonstrates the effectiveness of analysis by EQCM-D in selecting electrolytes for batteries comprising organic electrodes.
RESUMEN
Owing to its high energy density, LiNi0.8Co0.1Mn0.1O2 (NMC811) is a cathode material of prime interest for electric vehicle battery manufacturers. However, NMC811 suffers from several irreversible parasitic reactions that lead to severe capacity fading and impedance buildup during prolonged cycling. Thin surface protection films coated on the cathode material mitigate degradative chemomechanical reactions at the electrode-electrolyte interphase, which helps to increase cycling stability. However, these coatings may impede the diffusion of lithium ions, and therefore, limit the performance of the cathode material at a high C-rate. Herein, we report on the synthesis of zirconium phosphate (ZrxPOy) and lithium-containing zirconium phosphate (LixZryPOz) coatings as artificial cathode-electrolyte interphases (ACEIs) on NMC811 using the atomic layer deposition technique. Upon prolonged cycling, the ZrxPOy- and LixZryPOz-coated NMC811 samples show 36.4 and 49.4% enhanced capacity retention, respectively, compared with the uncoated NMC811. Moreover, the addition of Li ions to the LixZryPOz coating enhances the rate performance and initial discharge capacity in comparison to the ZrxPOy-coated and uncoated samples. Using online electrochemical mass spectroscopy, we show that the coated ACEIs largely suppress the degradative parasitic side reactions observed with the uncoated NMC811 sample. Our study demonstrates that providing extra lithium to the ACEI layer improves the cycling stability of the NMC811 cathode material without sacrificing its rate capability performance.
RESUMEN
In recent decades, rechargeable Mg batteries (RMBs) technologies have attracted much attention because the use of thin Mg foil anodes may enable development of high-energy-density batteries. One of the most critical challenges for RMBs is finding suitable electrolyte solutions that enable efficient and reversible Mg cells operation. Most RMB studies concentrate on the development of novel electrolyte systems, while only few studies have focused on the practical feasibility of using pure metallic Mg as the anode material. Pure Mg metal anodes have been demonstrated to be useful in studying the fundamentals of nonaqueous Mg electrochemistry. However, pure Mg metal may not be suitable for mass production of ultrathin foils (<100â microns) due to its limited ductility. The metals industry overcomes this problem by using ductile Mg alloys. Herein, the feasibility of processing ultrathin Mg anodes in electrochemical cells was demonstrated by using AZ31 Mg alloys (3 % Al; 1 % Zn). Thin-film Mg AZ31 anodes presented reversible Mg dissolution and deposition behavior in complex ethereal Mg electrolytes solutions that was comparable to that of pure Mg foils. Moreover, it was demonstrated that secondary Mg battery prototypes comprising ultrathin AZ31 Mg alloy anodes (≈25â µm thick) and Mgx Mo6 S8 Chevrel-phase cathodes exhibited cycling performance equal to that of similar cells containing thicker pure Mg foil anodes. The possibility of using ultrathin processable Mg metal anodes is an important step in the realization of rechargeable Mg batteries.
RESUMEN
Knowledge of intrinsic properties is of central importance for materials design and assessing suitability for specific applications. Self-assembling block copolymer electrolytes (BCEs) are of great interest for applications in solid-state energy storage devices. A fundamental understanding of ion transport properties, however, is hindered by the difficulty in deconvoluting extrinsic factors, such as defects, from intrinsic factors, such as the presence of interfaces between the domains. Here, we quantify the intrinsic ion transport properties of a model BCE system consisting of poly(styrene-block-ethylene oxide) (SEO) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt using a generalizable strategy of depositing thin films on interdigitated electrodes and self-assembling fully connected parallel lamellar structures throughout the films. Comparison between conductivity in homopolymer poly(ethylene oxide) (PEO)-LiTFSI electrolytes and the analogous conducting material in SEO over a range of salt concentrations (r, molar ratio of lithium ion to ethylene oxide repeat units) and temperatures reveals that between 20% and 50% of the PEO in SEO is inactive. Using mean-field theory calculations of the domain structure and monomer concentration profiles at domain interfaces-both of which vary substantially with salt concentration-the fraction of inactive PEO in the SEO, as derived from conductivity measurements, can be quantitatively reconciled with the fraction of PEO that is mixed with greater than a few volume percent of polystyrene. Despite the detrimental interfacial effects for ion transport in BCEs, the intrinsic conductivity of the SEO studied here (ca. 10-3 S/cm at 90 °C, r = 0.085) is an order of magnitude higher than reported values from bulk samples of similar molecular weight SEO (ca. 10-4 S/cm at 90 °C, r = 0.085). Overall, this work provides motivation and methods for pursuing improved BCE chemical design, interfacial engineering, and processing.
RESUMEN
Using UV-vis spectroscopy in conjunction with various electrochemical techniques, we have developed a new effective operando methodology for investigating the oxygen reduction reactions (ORRs) and their mechanisms in nonaqueous solutions. We can follow the in situ formation and presence of superoxide moieties during ORR as a function of solvent, cations, anions, and additives in the solution. Thus, using operando UV-vis spectroscopy, we found evidence for the formation of superoxide radical anions during oxygen reduction in LiTFSI/diglyme electrolyte solutions. Nitro blue tetrazolium (NBT) was used to indicate the presence of superoxide moieties based on its unique spectral response. Indeed, the spectral response of NBT containing solutions undergoing ORR could provide a direct indication for the level of association of the Li cations with the electrolyte anions.
RESUMEN
We have examined the effect of glyme selection on the cycling behavior of Li-O2 cells. We conclude that diglyme is the optimal solvent for prolonged cycling. We have also focused on the effect of electrolyte solution instability as compared to other cell components.
RESUMEN
Aprotic Li-O2 battery is an exciting concept. The enormous theoretical energy density and cell assembly simplicity make this technology very appealing. Nevertheless, the instability of the cell components, such as cathode, anode, and electrolyte solution during cycling, does not allow this technology to be fully commercialized. One of the intrinsic challenges facing researchers is the use of lithium metal as an anode in Li-O2 cells. The high activity toward chemical moieties and lack of control of the dissolution/deposition processes of lithium metal makes this anode material unreliable. The safety issues accompanied by these processes intimidate battery manufacturers. The need for a reliable anode is crucial. In this work we have examined the replacement of metallic lithium anode in Li-O2 cells with lithiated hard carbon (HC) electrodes. HC anodes have many benefits that are suitable for oxygen reduction in the presence of solvated lithium cations. In contrast to lithium metal, the insertion of lithium cations into the carbon host is much more systematic and safe. In addition, with HC anodes we can use aprotic solvents such as glymes that are suitable for oxygen reduction applications. By contrast, lithium cations fail to intercalate reversibly into ordered carbon such as graphite and soft carbons using ethereal electrolyte solutions, due to detrimental co-intercalation of solvent molecules with Li ions into ordered carbon structures. The hard carbon electrodes were prelithiated prior to being used as anodes in the Li-O2 rechargeable battery systems. Full cells containing diglyme based solutions and a monolithic carbon cathode were measured by various electrochemical methods. To identify the products and surface films that were formed during cells operation, both the cathodes and anodes were examined ex situ by XRD, FTIR, and electron microscopy. The HC anodes were found to be a suitable material for (Li-ion)-O2 cell. Although there are still many challenges to tackle, this study offers a more practical direction for this promising battery technology and sets up a platform for further systematic optimization of its various components.
RESUMEN
The kinetics and thermodynamics of oxygen reduction reactions (ORR) in aprotic Li electrolyte were shown to be highly dependent on the surrounding chemical environment and electrochemical conditions. Numerous reports have demonstrated the importance of high donor number (DN) solvents for enhanced ORR, and attributed this phenomenon to the stabilizing interactions between the reduced oxygen species and the solvent molecules. We focus herein on the often overlooked effect of the Li salt used in the electrolyte solution. We show that the level of dissociation of the salt used plays a significant role in the ORR, even as important as the effect of the solvent DN. We clearly show that the salt used dictates the kinetics and thermodynamic of the ORR, and also enables control of the reduced Li2O2 morphology. By optimizing the salt composition, we have managed to demonstrate a superior ORR behavior in diglyme solutions, even when compared to the high DN DMSO solutions. Our work paves the way for optimization of various solvents with reasonable anodic and cathodic stabilities, which have so far been overlooked due to their relatively low DN.
RESUMEN
The development of a successful Li-O2 battery depends to a large extent on the discovery of electrolyte solutions that remain chemically stable through the reduction and oxidation reactions that occur during cell operations. The influence of the electrolyte anions on the behavior of Li-O2 cells was thought to be negligible. However, it has recently been suggested that specific anions can have a dramatic effect on the chemistry of a Li-O2 cell. In the present paper, we describe how LiNO3 in polyether solvents can improve both oxygen reduction (ORR) and oxygen evolution (OER) reactions. In particular, the nitrate anion can enhance the ORR by enabling a mechanism that involves solubilized species like superoxide radicals, which allows for the formation of submicronic Li2O2 particles. Such phenomena were also observed in Li-O2 cells with high donor number solvents, such as dimethyl sulfoxide dimethylformamide (DMF) and dimethylacetamide (DMA). Nevertheless, their instability toward oxygen reduction, lithium metals, and high oxidation potentials renders them less suitable than polyether solvents. In turn, using catalysts like LiI to reduce the OER overpotential might enhance parasitic reactions. We show herein that LiNO3 can serve as an electrolyte and useful redox mediator. NO2(-) ions are formed by the reduction of nitrate ions on the anode. Their oxidation forms NO2, which readily oxidizes to Li2O2. The latter process moves the OER overpotentials down into a potential window suitable for polyether solvent-based cells. Advanced analytical tools, including in situ electrochemical quartz microbalance (EQCM) and ESR plus XPS, HR-SEM, and impedance spectroscopy, were used for the studies reported herein.
RESUMEN
Polyether solvents are considered interesting and important candidates for Li-O2 battery systems. Discharge of Li-O2 battery systems forms Li oxides. Their mechanism of formation is complex. The stability of most relevant polar aprotic solvents toward these Li oxides is questionable. Specially high surface area carbon electrodes were developed for the present work. In this study, several spectroscopic tools and in situ measurements using electrochemical quartz crystal microbalance (EQCM) were employed to explore the discharge-charge processes and related side reactions in Li-O2 battery systems containing electrolyte solutions based on triglyme/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) electrolyte solutions. The systematic mechanism of lithium oxides formation was monitored. A combination of Fourier transform infrared (FTIR), NMR, and matrix-assisted laser desorption/ionization (MALDI) measurements in conjunction with electrochemical studies demonstrated the intrinsic instability and incompatibility of polyether solvents for Li-air batteries.
RESUMEN
In this study we compared reproductive characteristics and steroid hormone levels in the non-indigenous scleractinian coral, Oculina patagonica, inhabiting contaminated vs. uncontaminated reference sites along the Israeli Mediterranean coast. Our results indicate significantly higher steroid levels in both seawater and coral tissue samples from contaminated sites as compared to reference sites, suggesting that corals tend to accumulate steroids from the surrounding waters. Despite their higher steroid levels, corals from the contaminated sites showed reproductive potential comparable to those of the reference sites. Interestingly, a clear distinction could be seen between corals exposed to pollution for long vs. short durations, with the latter showing a failure to complete gametogenesis. This suggests that reproduction in O. patagonica is susceptible to acute rather than chronic stress. The involvement of adjustment/adaptation processes may explain this species tolerance, and may reflect the ability of O. patagonica to successfully invade new areas in the Mediterranean Sea.