CT-based thermometry with virtual monoenergetic images by dual-energy of fat, muscle and bone using FBP, iterative and deep learning-based reconstruction.

OBJECTIVES: The aim of this study was to evaluate the sensitivity of CT-based thermometry for clinical applications regarding a three-component tissue phantom of fat, muscle and bone. Virtual monoenergetic images (VMI) by dual-energy measurements and conventional polychromatic 120-kVp images with modern reconstruction algorithms adaptive statistical iterative reconstruction-Volume (ASIR-V) and deep learning image reconstruction (DLIR) were compared. METHODS: A temperature-regulating water circuit system was developed for the systematic evaluation of the correlation between temperature and Hounsfield units (HU). The measurements were performed on a Revolution CT with gemstone spectral imaging technology (GSI). Complementary measurements were performed without GSI (voltage 120 kVp, current 130-545 mA). The measured object was a tissue equivalent phantom in a temperature range of 18 to 50°C. The evaluation was carried out for VMI at 40 to 140 keV and polychromatic 120-kVp images. RESULTS: The regression analysis showed a significant inverse linear dependency between temperature and average HU regardless of ASIR-V and DLIR. VMI show a higher temperature sensitivity compared to polychromatic images. The temperature sensitivities were 1.25 HU/°C (120 kVp) and 1.35 HU/°C (VMI at 140 keV) for fat, 0.38 HU/°C (120 kVp) and 0.47 HU/°C (VMI at 40 keV) for muscle and 1.15 HU/°C (120 kVp) and 3.58 HU/°C (VMI at 50 keV) for bone. CONCLUSIONS: Dual-energy with VMI enables a higher temperature sensitivity for fat, muscle and bone. The reconstruction with ASIR-V and DLIR has no significant influence on CT-based thermometry, which opens up the potential of drastic dose reductions. KEY POINTS: • Virtual monoenergetic images (VMI) enable a higher temperature sensitivity for fat (8%), muscle (24%) and bone (211%) compared to conventional polychromatic 120-kVp images. • With VMI, there are parameters, e.g. monoenergy and reconstruction kernel, to modulate the temperature sensitivity. In contrast, there are no parameters to influence the temperature sensitivity for conventional polychromatic 120-kVp images. • The application of adaptive statistical iterative reconstruction-Volume (ASIR-V) and deep learning-based image reconstruction (DLIR) has no effect on CT-based thermometry, opening up the potential of drastic dose reductions in clinical applications.

MRI following scoliosis surgery? An analysis of implant heating, displacement, torque, and susceptibility artifacts.

OBJECTIVES: The implant constructs used in scoliosis surgery are often long with a high screw density. Therefore, it is generally believed that magnetic resonance imaging (MRI) should not be carried out after scoliosis surgery, with the result that computed tomography is often preferred despite the ionizing radiation involved. The objective of this study was to evaluate the MRI compatibility of long pedicle-screw-rod constructs at 1.5 T and 3 T using standardized methods of the American Society for Testing and Materials (ASTM). METHODS: Constructs between 130 and 430 mm long were systematically examined according to the ASTM standards F2182 (radio frequency-induced heating), F2119 (susceptibility artifacts), F2213 (magnetically induced torque), and F2052 (magnetically induced displacement force). RESULTS: The maximum heating in the magnetic field was 1.3 K. Heating was significantly influenced by magnetic field strength (p < 0.001), implant length (p = 0.048), and presence of cross-links (p = 0.001). The maximum artifact width for different lengths of the anatomically bent titanium rods with CoCr alloy ranged between 14.77 ± 2.93 mm (TSE) and 17.49 ± 1.82 mm (GRE) for 1.5 T and between 23.67 ± 2.39 mm (TSE) and 27.77 ± 2.37 mm (GRE) for 3 T. TiCP and TiAl showed the smallest and CoCr and CoCr Plus the largest artifact widths. The magnetically induced torque and displacement force were negligible. CONCLUSIONS: MRI following scoliosis surgery with long implant constructs is safe with the patient in supine position. Although susceptibility artifacts can severely limit the diagnostic value, the examination of other regions is possible. KEY POINTS: • Large spinal implants are not necessarily a contraindication for MRI; MR conditional status can be examined according to the ASTM standards F2182, F2119, F2213, and F2052. • A metallic pedicle-screw-rod system could be reliably and safely examined in all combinations of length (130 to 430 mm), configuration, and material in a B0 at 1.5 T and 3 T. • According to ASTM F2503, the examined pedicle-screw-rod system is MR conditional and especially the young patients can benefit from a non-ionizing radiation MRI examination.

MR-guided facet joint injection therapy using an open 1.0-T MRI system: an outcome study.

OBJECTIVES: To evaluate the accuracy, safety and efficacy of magnetic resonance imaging (MRI)-guided facet joint injection therapy using a 1.0-T open MRI. METHODS: One hundred and sixty-six facet joint blocks in 45 patients with lower back pain were performed under MR fluoroscopic guidance using a proton-density-weighted turbo-spin-echo sequence. An in-room monitor, wireless MR-mouse for operator-controlled multiplanar navigation, a flexible surface coil and MR-compatible 20-G needle were used. Clinical outcome was evaluated by questionnaire before intervention and after 1 week, 3, 6 and 12 months using a numerical visual analogue scale (VAS). RESULTS: All facet joint blocks were considered technically successful with distribution of the injectant within and/or around the targeted facet joint. No major complications occurred. The final outcome analysis included 38 patients. An immediate effect was reported by 63 % of the patients. A positive mid-/long-term effect was seen in 13 patients (34 %) after 6 months and in 9 patients (24 %) after 12 months. Mean VAS was reduced from 7.1 ± 1.7 (baseline) to 3.5 ± 2.2, 4.1 ± 3.0, 3.8 ± 2.9 and 4.6 ± 2.9 at 1 week, 3, 6 and 12 months (P < 0.01). CONCLUSIONS: MR-guided facet joint injection therapy of the lumbosacral spine is accurate, safe and efficient in the symptomatic treatment of lower back pain.

MR guidance and thermometry of percutaneous laser disc decompression in open MRI: an initial clinical investigation.

OBJECTIVES: To assess the feasibility, safety and efficacy of real-time MR guidance and thermometry of percutaneous laser disc decompression (PLDD). METHODS: Twenty-four discs in 22 patients with chronic low-back and radicular pain were treated by PLDD using open 1.0-T magnetic-resonance imaging (MRI). A fluoroscopic proton-density-weighted turbo spin-echo (PDw TSE) sequence was used to position the laser fibre. Non-spoiled gradient-echo (GRE) sequences were employed for real-time thermal monitoring based on proton resonance frequency (PRF). Radicular pain was assessed over 6 months with a numerical rating scale (NRS). RESULTS: PLDD was technically successful in all cases, with adequate image quality for laser positioning. The PRF-based real-time temperature monitoring was found to be feasible in practice. After 6 months, 21 % reported complete remission of radicular pain, 63 % at least great pain relief and 74 % at least mild relief. We found a significant decrease in the NRS score between the pre-intervention and the 6-month follow-up assessment (P < 0.001). No major complications occurred; the single adverse event recorded, moderate motor impairment, resolved. CONCLUSIONS: Real-time MR guidance and PRF-based thermometry of PLDD in the lumbar spine under open 1.0-T MRI appears feasible, safe and effective and may pave the way to more precise operating procedures. KEY POINTS: • Percutaneous laser disc decompression (PLDD) is increasingly used instead of conventional surgery. • Open 1.0-T MRI with temperature mapping seems technically successful in monitoring PLDD. • Pain relief was at least 'great' in 64 % of patients. • No major complications occurred. • Open 1.0-T MRI appears a safe and effective option for patient-tailored PLDD.

Ankle laxity: stress investigation under MRI control.

OBJECTIVE: The purpose of this study was to examine the advantages of MRI-guided ankle stress examinations in the detection of chronic ankle instability. SUBJECTS AND METHODS: An MRI-compatible stress device was developed and tested for MRI safety. Bilateral MRI stress examinations were performed on 50 volunteers with and without clinically evident subjective instability of the ankle joints (72 subjective stable ankle joints in 37 subjects, 28 ankles in 15 subjects with chronic ankle instability). Both the inversion test and the anterior drawer test were performed under axial, coronal, 45° paraxial, and sagittal T2-weighted fast spin-echo image control. MR images were assessed for talar tilt, subtalar tilt, anterior talus translation, anterior calcaneus translation, medial talocalcaneal translation, and the diameters of the lateral ankle ligaments (anterior talofibular ligament, calcaneofibular ligament, and posterior talofibular ligament). RESULTS: The MRI stress device was found suitable and safe for use in the MRI environment. The talocrural and subtalar joints could be assessed simultaneously. Significant differences between groups A and B (p≤0.05) were found in talar tilt, subtalar tilt, anterior talus translation, anterior calcaneus translation, medial talocalcaneal translation, and decrease in diameters of calcaneofibular and posterior talofibular ligaments. Also found were sex differences in talar tilt, subtalar tilt, anterior talus translation, and diameters of the anterior talofibular, calcaneofibular, and posterior talofibular ligaments. Significant relations were found between talar tilt and anterior talus translation, subtalar tilt and anterior calcaneus translation, subtalar tilt and medial talocalcaneal translation, and between anterior calcaneus translation and medial talocalcaneal translation in groups A and B. CONCLUSION: Stress examination under MRI control has advantages in the assessment of mechanical ankle instability. Additional diagnostic and clinically relevant information is obtained through direct imaging of the ligaments and assessment of additional parameters of ankle laxity (subtalar tilt, anterior calcaneus translation, medial talocalcaneal translation). The main advantages are objective imaging and measurement of abnormal looseness of the lower ankle joint and its direct simultaneous comparison with the upper ankle joint.

Evaluation of a MR-quadrupole imaging coil for spinal interventions in a vertical 1.0 T MRI.

The in vivo pain treatment was successfully performed with the patient in a prone position. The PD-weighted TSE with echo time = 10 ms rendered contrast-to-noise-ratio values of 27 ± 10 for needle/fat, 1.6 ± 5 for needle/muscle, and 4 ± 4.7 for needle/nerve tissue. The mean diameter of the needle artifact was 1.2 ± 0.2 mm. In the T(1)-weighted gradient echo, the needle's artifact diameter was 6 ± 2 mm; the needle's contrast-to-noise ratio relative to muscle tissue was 4 ± 2, 7.6 ± 1.5 for needle/fat, and 5 ± 1 for needle/nerve tissue. With the PD-weighted TSE (echo time = 10 ms) and the T(1)-weighted gradient echo, the needle was imaged reliably throughout the intervention. The butterfly surface coil is feasible for the guidance of spinal interventions in a prone patient.

Soluble mannose receptor CD206 and von Willebrand factor are early biomarkers to identify patients at risk for severe or necrotizing acute pancreatitis.

BACKGROUND: In acute pancreatitis (AP), microcirculatory dysfunction and leukocyte activation contribute to organ damage, inflammation, and mortality. Given the role of macrophage activation, monocyte recruitment, and microthrombus formation in the early pathogenesis of AP, we examined the macrophage activation marker soluble mannose receptor (sCD206) and the endothelial function marker von Willebrand factor (vWF) in patients admitted for AP. METHODS: In an exploratory analysis, serum sCD206 and plasma vWF were prospectively analyzed on day 1 and day 3 in 81 patients with AP admitted to the hospital. In addition, blood samples from 59 patients with early AP admitted to the intensive care unit and symptom onset < 24 h were retrospectively analyzed. Patients were dichotomized as per study protocol into two groups: (i) "non-severe edematous AP" including patients with mild AP without organ failure and patients with transient organ failure that resolves within 48 h and (ii) "severe/necrotizing AP" including patients with severe AP and persistent organ failure > 48 h and/or patients with local complications. RESULTS: In the prospective cohort, 17% developed severe/necrotizing pancreatitis compared with 56% in the ICU cohort. Serum concentrations of sCD206 on admission were higher in patients with severe/necrotizing AP than in patients with non-severe edematous AP (prospective: 1.57 vs. 0.66 mg/l, P = 0.005; ICU: 1.76 vs. 1.25 mg/l, P = 0.006), whereas other inflammatory markers (leukocytes, C-reactive protein, procalcitonin) and disease severity (SOFA, SAPS II, APACHE II) did not show significant differences. Patients with severe/necrotizing AP had a greater increase in sCD206 than patients with non-severe edematous AP at day 3 in the prospective cohort. In contrast to routine coagulation parameters, vWF antigen levels were elevated on admission (prospective cohort: 375 vs. 257%, P = 0.02; ICU cohort: 240 vs. 184%, P = 0.03). When used as continuous variables, sCD206 and VWF antigen remained predictors of severe/necrotizing AP after adjustment for etiology and age in both cohorts. CONCLUSIONS: sCD206 identifies patients at risk of severe AP at earlier timepoints than routine markers of inflammation and coagulation. Prospective studies are needed to investigate whether incorporating early or repeated measurements into the existing scoring system will better identify patients at increased risk for complications of AP.

Outcome analysis in 3,160 implantations of radiologically guided placements of totally implantable central venous port systems.

OBJECTIVES: In this retrospective study the success and complication rates after radiologically guided port catheter implantation were evaluated. METHODS: Between 2000 and 2008, 3,160 port catheter systems were implanted in our interventional suite. All interventions were imaging guided. The puncture of the preferably right internal jugular vein (IJV) was ultrasound-assisted and the catheter tip position was controlled with fluoroscopy. Catheter indwelling time and rates of periprocedural, early and late complications were evaluated. RESULTS: 922,599 catheter days (mean, 292 days; range, 0-2,704 days) were documented. The implantation was successful in 3,153 (99.8%) cases. A total of 374 (11.8%; 0.41/1,000 catheter days) adverse events were recorded. Of these, 42 (1.33%) were periprocedural complications. 86 (3.3%; 0.09/1,000 catheter days) early and 246 (9.4%; 0.27/1,000 catheter days) late onset complications occurred after port implantation. The most common complications were blood stream infection (n = 134; 5.1%; 0.15/1,000 catheter days), catheter-induced venous thrombosis (n = 97; 3.7%; 0.11/1,000 catheter days) and catheter migration (n = 34; 1.3%; 0.04/1,000 catheter days). A total of 193 (6.1%) port explantations were required. CONCLUSION: Ultrasound guided port implantation via the IJV results in low periprocedural complication rates.

Intradiscal temperature monitoring using double gradient-echo pulse sequences at 1.0T.

PURPOSE: To validate an unspoiled gradient-recalled echo pulse sequence with dual echo acquisition as a means to increase temperature sensitivity while monitoring intradiscal laser ablation therapy. MATERIALS AND METHODS: Phantom experiments as well as in vitro thermal ablation simulations were performed in an open 1.0T magnetic resonance (MR) scanner. Three methods of noninvasive MR-thermometry based on the signal void decrease caused by T1-relaxation time increase (T1), the temperature-dependent proton resonance frequency (PRF) shift, and a combination of both methods with complex differences (CD) were compared. Temperature accuracy and reliability of temperature distribution were the main assessment criteria. RESULTS: The optimum temperature sensitivity was found using CD in phantom experiments. During in vitro experiments the PRF showed the smallest margin of error (T1: +/-1.64 degrees C, PRF: +/-1.23 degrees C, CD: +/-1.29 degrees C) and the best qualitative evaluation of temperature. CONCLUSION: Intradiscal temperature monitoring with an unspoiled dual-echo sequence is most accurate with PRF-thermometry in combination with the long echo time. Magnitude images with an initial short echo time permit high image detail of the heat-induced lesion.

Passive navigation principle for orthopedic interventions with MR fluoroscopy.

INTRODUCTION: Of late, computer-assisted surgery has become a novel challenge for orthopedic surgeons. However, for orthopedic interventions magnetic resonance (MR) fluoroscopy is in its early stages of development. The authors have developed an innovative passive navigation concept, which is potentially applicable for many magnetic resonance image (MRI)-guided musculoskeletal interventions. With this method, no switching between different planes is required, since the cross-sectional modality of the MRI is used as a new navigation approach. MATERIALS AND METHODS: This method was mainly evaluated in retrograde drilling of artificial osteochondral lesions of the talus as an example of difficult navigation in drill placement due to poor visualization with X-ray and complex anatomy. To accomplish this objective, a passive navigation device was constructed and evaluated in nine cadaveric ankle joint specimens. Feasibility and accuracy of navigated drillings were evaluated. RESULTS: The interactive high-field MR fluoroscopy and the passive aiming device allow precise drilling of osteochondral lesions of the talus, despite the complex anatomy of the ankle. Drillings could be performed with an accuracy of 1.6 mm. The drilling guide was safe and easy to handle. CONCLUSION: The MR-assisted retrograde drilling of osteochondral lesions may enable precise and safe treatment without radiation exposure. This passive navigation technique for MR fluoroscopy is potentially applicable for many orthopedic interventions and may present an alternative to other navigation methods. Especially, the treatment of pediatric and adolescent patients may benefit from the typical MRI properties.

Automatic human identification based on dental X-ray radiographs using computer vision.

A person may be identified by comparison between ante- and post-mortem dental panoramic radiographs (DPR). However, it is difficult to find reference material if the person is unknown. This is often the case when victims of crime or mass disaster are found. Computer vision can be a helpful solution to automate the finding of reference material in a large database of images. The purpose of the present study was to improve the automated identification of unknown individuals by comparison of ante- and post-mortem DPR using computer vision. The study includes 61,545 DPRs from 33,206 patients, acquired between October 2006 and June 2018. The matching process is based on the Speeded Up Robust Features (SURF) algorithm to find unique corresponding points between two DPRs (unknown person and database entry). The number of matching points found is an indicator for identification. All 43 individuals (100%) were successfully identified by comparison with the content of the feature database. The experimental setup was designed to identify unknown persons based on their DPR using an automatic algorithm system. The proposed tool is able to filter large databases with many entries of potentially matching partners. This identification method is suitable even if dental characteristics were removed or added in the past.

Systematic evaluation of particle loss during handling in the percutaneous transluminal angioplasty for eight different drug-coated balloons.

Paclitaxel drug coated balloons (DCBs) should provide optimal drug transfer exclusively to the target tissue. The aim of this study was to evaluate the particle loss by handling during angioplasty. A robotic arm was developed for systematic and reproducible drug abrasion experiments. The contact force on eight different commercially available DCB types was gradually increased, and high-resolution microscopic images of the deflated and inflated balloons were recorded. Three types of DCBs were classified: no abrasion of the drug in both statuses (deflated and inflated), significant abrasion only in the inflated status, and significant abrasion in both statuses. Quantitative measurements via image processing confirmed the qualitative classification and showed changes of the drug area between 2.25 and 45.73% (13.28 ± 14.29%) in the deflated status, and between 1.66 and 40.41% (21.43 ± 16.48%) in the inflated status. The structures and compositions of the DCBs are different, some are significantly more susceptible to drug loss. Particle loss by handling during angioplasty leads to different paclitaxel doses in the target regions for same DCB types. Susceptibility to involuntary drug loss may cause side effects, such as varying effective paclitaxel doses, which may explain variations in studies regarding the therapeutic outcome.

Osteochondral lesions of the talus: retrograde drilling with high-field-strength MR guidance.

The institutional review board approved the use of cadaveric specimens, and informed consent was obtained from all volunteers. The authors performed and assessed a magnetic resonance (MR)-assisted navigation method for minimally invasive retrograde drilling of talar osteochondral lesions. For this method, a single imaging plane is sufficient for navigation during intervention. To accomplish this objective, a passive MR navigation device was used to evaluate 16 cadaveric ankle joints. Use of this interactive MR-assisted navigation method in combination with a passive aiming device allowed precise and rapid retrograde drilling of talar osteochondral lesions.

Sonographically guided placement of intravenous catheters in minipigs.

Many procedures in minipigs require establishment of reliable deep venous access with a large-bore catheter. In animal experiments, such catheters are typically implanted surgically. In clinical settings, however, ultrasound imaging is routinely used to facilitate safe, minimally invasive puncture of deep vessels. The authors describe a technique for using ultrasound guidance to puncture and cannulate the minipig femoral vein. They carried out the procedure in six minipigs for the purpose of injecting contrast agents for subsequent imaging scans. The procedure was ultimately successful in all pigs, took 10 min on average and resulted in no physiological complications. In one minipig, however, a 10-cm-long catheter became dislodged from the femoral vein; use of a longer (25-cm-long) catheter was optimal for establishing reliable intravenous access.

In vitro stent assessment by MRI: visibility of lumen and artifacts for 27 modern stents.

PURPOSE: The purpose of this study was to measure artifacts and visibility of lumen for modern and most commonly used stents in vascular interventions according to a standardized test method of the American Society for Testing and Materials (ASTM). MATERIALS AND METHODS: Twenty-four peripheral self-expanding nitinol stents and three stainless steel stents with diameters between 5 and 8 mm and lengths between 30 and 250 mm from seven different manufacturers were compared on a 1.5T and a 3T magnetic resonance (MR) scanner. The visualization of lumen and artifacts was measured according to ASTM F2119 for a turbo spin echo (TSE) [repetition time(TR)/echo time (TE) 500/26 ms] and a gradient echo (GRE) (TR/TE 100/15 ms) sequence. The stents were placed parallel and perpendicular to the radio frequency field (B1). RESULTS: There were large differences in visibility of the lumen for the stent models. The visualization of the lumen varies between 0% and 93% (perpendicular to B1), and 0% and 78% (parallel to B1), respectively. The maximum signal loss beyond the actual diameter was 6 mm (TSE) and 10 mm (GRE) for stents made of stainless steel, and lower than 1 mm (TSE) and 4 mm (GRE) for nitinol stents. CONCLUSION: Reliable stent lumen visualization is possible for Misago, Supera, Tigris, and Viabahn stents, if their axis is perpendicular to B1, and independent of the orientation with respect to B1 for short Tigris stents at 1.5T.

Improvement of olfactory function after sinus surgery correlates with white matter properties measured by diffusion tensor imaging.

Impaired olfaction is associated with a volume decrease in the olfactory bulb as well as in the gray matter of cortical olfactory areas. On the other hand, restitution of an impaired olfaction results in a regain of volume in these regions. Studies investigating similar changes in the cerebral white matter are virtually not existent. The aim of this prospective study therefore was to investigate cerebral white matter using magnetic resonance diffusion tensor imaging (DTI). 31 patients (54±13years) with olfactory impairment (chronic rhinosinusitis) and planned functional endoscopic sinus surgery (FESS) were included. Magnetic resonance imaging (MRI) data sets were acquired pre-operatively and 3months after surgery. Pre- and postoperative olfactory testing was performed to assess the olfactory threshold, discrimination, and identification (TDI) score. A significant postoperative TDI improvement by 9.06±8.81 points was observed. Two groups were subsequently formed - one with relevant postoperative olfactory gain (ΔTDI≥10 points, 12 patients) and one without gain (ΔTDI<10 points, 19 patients). DTI parameter showed a significant correlation with the TDI score in the left anterior cingulate cortex and the right amygdala. In the group with relevant olfactory improvement higher values of fractional anisotropy and apparent diffusion coefficient were found in the right parahippocampal area and in the white matter below the left inferior temporal sulcus. Tract-specific diffusion property analysis revealed significant group differences in the cingulate cortex in spatial relationship to the perisplenial cortex. Overall, this prospective study indicates structural changes in white matter after postoperative restoration of olfaction.

Portable computed tomography performed on the intensive care unit.

OBJECTIVE: We report on the use of portable computed tomography (CT) in an ICU setting. The additional diagnostic gain and therapeutic consequences were assessed. PATIENTS: Ten ICU patients underwent 14 portable chest CT examinations. In 64% maximum intensive care was required, according to TISS28 (>40), and 42% were at a risk of mortality higher than 25% (MODS) on the day of portable CT examination. In three portable CT examinations the patients were considered not transportable and were examined directly in the patient room. All other examinations were performed in a special interventional suite directly on the ICU. RESULTS: Of 14 examinations 8 (57%) resulted in a change in patient management within 48 h. All patients profited from portable CT and no hazards occurred related to CT. CONCLUSIONS: To perform portable CT in the interventional suite on the ICU allows immediate minimally invasive therapeutic interventions and provides full ICU monitoring.

[Using network planning techniques for work flow analysis in a clinical environment]. / Anwendung der Netzplantechnik für die Arbeitsprozessanalyse im klinischen Bereich.

In the face of increasing financial pressure on our health care system, one way to reduce costs while maintaining or even improving outcome quality is to improve work flow efficiency. Network Planning Technique (NPT) is a tool for mapping and analyzing work flows. Designing a network plan requires four steps. Step 1 is concerned with the determination of the work flow structure. Step 2 deals with data acquisition. Based on the data retrieved a network plan is created in Step 3. Step 4 includes the calculation of the critical path and slack times under optimistic, realistic and pessimistic conditions. Applied to the ultrasound division in our department a total examination time of 34:14 minutes was calculated with 23:09 minutes total slack time for the technician under realistic conditions. Using NPT creates transparency in work flows and allows us to estimate resource demands. A comparison between two different divisions with a similar work flow structure but different resource allocation demonstrates this method's potential for improving work flows. Limitations of the NPT can be noted when considering cycle overlap in repetitive work flows and modeling non-regular activities.

MR guidance and thermometry of percutaneous laser disc decompression in open MRI: an ex vivo study.

PURPOSE: To assess the feasibility of guidance and thermometry by open 1.0 T magnetic resonance (MR) imaging during percutaneous laser disc decompression (PLDD). METHODS: A fluoroscopic proton-density-weighted turbo spin echo sequence was used for positioning a laser fiber and a reference thermosensor within the targeted spinal disc. In 30 lumbar discs from human donors, nonspoiled gradient-echo (GRE) sequences with different echo times (TE) were compared to monitor thermal laser effects (Nd:YAG laser, 1,064 nm). Temperature distribution was visualized in real time on the basis of T1-weighted images and the proton resonance frequency (PRF) technique. Image quality, temperature accuracy, and correlation with macroscopic lesion sizes were analyzed. Image quality was confirmed in healthy volunteers. RESULTS: MR-guided placement of the laser fiber in the center of the targeted disk was precise. Best overall PLDD results-considering image quality (contrast-to-noise ratio), temperature accuracy (R (2) = 0.96), and correlation between the macroscopic and MR lesions (R (2) = 0.63)-were achieved with TE at 7 ms. The same TE value also gave the best image quality with healthy volunteers. CONCLUSION: Instrument guidance and PRF-based thermometry of PLDD in the lumbar spine are feasible and accurate. Open 1.0 T MR imaging with fast spin-echo and GRE sequence designs may render laser discectomies more effective and controllable.