RESUMEN
BACKGROUND: Liver iron concentration (LIC) measured by MRI has become the clinical reference standard for managing iron overload in chronically transfused patients. Transverse relaxivity (R2 or R2* ) measurements are converted to LIC units using empirically derived calibration curves. HYPOTHESIS: That flip angle (FA) error due to B1+ spatial heterogeneity causes significant LIC quantitation error. B1+ scale (b1 , [FAactual /FAspecified ]) variation is a major problem at 3 T which could reduce the accuracy of transverse relaxivity measurements. STUDY TYPE: Prospective. POPULATION: Forty-seven subjects with chronic transfusional iron overload undergoing clinically indicated LIC assessment. FIELD STRENGTH/SEQUENCE: 5 T/3 T dual-repetition time B1+ mapping sequence ASSESSMENT: We quantified the average/standard deviation b1 in the right and left lobes of the liver from B1+ maps acquired at 1.5 T and 3 T. The impact of b1 variation on spin echo LIC estimates was determined using a Monte Carlo model. STATISTICAL TESTS: Mean, median, and standard deviation in whole liver and right and left lobes; two-sided t-test between whole-liver b1 means. RESULTS: Average b1 within the liver was 99.3% ± 12.3% at 1.5 T versus 69.6% ± 14.6% at 3 T and was independent of iron burden (P < 0.05). Monte Carlo simulations demonstrated that b1 systematically increased R2 estimates at lower LIC (<~25 mg/g at 1.5 T, <~15 mg/g at 3 T) but flattened or even inverted the R2 -LIC relationship at higher LIC (≥~25 mg/g to 1.5 T, ≥~15 mg/g to 3 T); changes in the R2 -LIC relationship were symmetric with respect to over and under excitation and were similar at 1.5 T and 3 T (for the same R2 value). The R2* -LIC relationship was independent of b1 . CONCLUSION: Spin echo R2 measurement of LIC at 3 T is error-prone without correction for b1 errors. The impact of b1 error on current 1.5 T spin echo-based techniques for LIC quantification is large enough to introduce measurable intersubject variability but the in vivo effect size needs a dedicated validation study. TECHNICAL EFFICACY STAGE: 2.
Asunto(s)
Sobrecarga de Hierro , Hierro , Humanos , Sobrecarga de Hierro/diagnóstico por imagen , Hígado/diagnóstico por imagen , Imagen por Resonancia Magnética/métodos , Estudios ProspectivosRESUMEN
PURPOSE: CPMG spin echo acquisitions are attractive for diagnosing and monitoring liver iron concentration in iron overload disorders due to their time efficiency and potential to reveal unique information about tissue iron distribution. Clinical adoption remains low due to the insensitivity of CPMG-based R 2 estimates to liver iron concentration (LIC) when common fitting techniques are applied. In this work, we demonstrate that the inclusion of a proton density estimator (PDE) derived from the CPMG acquisition increase the sensitivity of CPMG R 2 estimates to LIC in both simulated and in-vivo human data. THEORY AND METHODS: CPMG R 2 acquisitions from 50 clinically indicated MRI studies in patients with iron overload were analyzed with and without PDE constraints. Liver regions of interest were fit to monoexpontial and nonexponential signal decay equations. LIC by R 2 ∗ served as the reference standard. The observed calibration between CPMG R 2 values and LIC were compared to results predicted from a previously validated Monte Carlo model. RESULTS: The sensitivity of CPMG-derived R 2 triples when a proton density constraint is applied. When compared with R 2 ∗ -LIC estimates, both monoexponential and nonexponential models were unbiased but demonstrated broad 95% confidence intervals particularly for LIC values below 12 mg/g. Absolute error did not increase with LIC. CONCLUSION: A proton density constraint can increase the sensitivity of CPMG-based models to iron. CPMG acquisitions are time-efficient and could potentially improve the dynamic range of single spin echo techniques as well as providing insight into tissue iron distribution.
Asunto(s)
Sobrecarga de Hierro , Protones , Humanos , Hierro , Sobrecarga de Hierro/diagnóstico por imagen , Hígado/diagnóstico por imagen , Imagen por Resonancia MagnéticaRESUMEN
Polyethylene melt conductivity was increased by adding a commercial anti-static agent, which resulted in a 20× decrease in electrospun fiber diameter and formation of a significant fraction of sub-micron diameter fibers. Two polyethylene formulations and varying additive concentrations were utilized to span the parameter space of conductivity and viscosity. The key role of conductivity in determining the jet radius (which sets the upper limit on the fiber size) is discussed in the context of fluid mechanics theory and previous simulations. Parameters which affect the conversion of the liquid jet to a solid fiber and the pertinent theory are outlined. An "unconfined" experimental configuration is utilized to both avoid potential needle clogging and enable direct observation of important characteristic length scales related to the interaction of the fluid and the applied electric field. In this approach, the fluid spontaneously forms an array of cone perturbations which act as stationary "nozzles" through which the mobile fluid flows to form the jet. The experimental data and theory considerations allow for a holistic discussion of the interaction between flow rate, viscosity, conductivity, and the resultant jet and fiber size. Information about the fluid viscosity and conductivity gained by observing the electrospinning process is highlighted. Schemes for theoretically predicting the cone-jet density, cone size, and flow rate are compared to experimental results.