Low-Temperature Methane Combustion Using Ozone over Coß Catalyst.

Catalytic methane (CH4) combustion is a promising approach to reducing the release of unburned methane in exhaust gas. Here, we report Co-exchanged ß zeolite (Coß) as an efficient catalyst for CH4 combustion using O3. A series of ion-exchanged ß zeolites (Co, Ni, Mn, Fe, and Pd) are subjected to the catalytic test, and Coß exhibits a superior performance in a low-temperature region (<100 °C). The results of X-ray absorption spectroscopy (XAS) and catalytic tests for Coß with different Co loadings indicate the isolated Co species is the plausible active site. The reaction mechanism of CH4 combustion over the isolated Co2+ cation is theoretically investigated by the single-component artificial force-induced reaction (SC-AFIR) method to thoroughly search for possible reaction routes. The resulting path toward CO2 formation shows an activation energy of 73 kJ/mol for the rate-determining step and an exothermicity of 1025 kJ/mol, which supports the experimental results. During a long-term catalytic test for 160 h without external heating, the CH4 conversion gradually decreases from 80 to 40%, but the conversion fully recovers after dehydration at 500 °C (0.5 h). The copresence of H2O and CO exhibits a negative impact on the catalytic activity, while NO and SO2 do not markedly change the catalytic activity.

Microporosity and Catalytic Activity for Hydrodesulfurization of Pharmacosiderite Mo4P3O16 Synthesized at a Moderate Temperature.

Pharmacosiderite Mo4P3O16 (Pharma-MoPO) consists of [Mo4O4] cubane unit and [PO4] tetrahedral to form an open framework with a microporous structure similar to that of LTA-type zeolite. Although attractive applications are expected due to its microporous structure and redox-active components, its physicochemical properties have been poorly investigated due to the specificity of its synthesis, which requires a high hydrothermal synthesis temperature of 360 °C. In this study, we succeeded in synthesizing Pharma-MoPO by hydrothermal synthesis at 230 °C, which can be applied using a commercially available autoclave by changing the metal source. Through the study of the solids and liquids obtained after hydrothermal syntheses, the formation process of Pharma-MoPO under our studied synthesis conditions was proposed. Advanced characterizations provided detailed structural information on Pharma-MoPO, including the location site of a countercation NH4+. Pharma-MoPO could adsorb CO2 with the amount close to the number of cages without removing NH4+. Pharma-MoPO exhibited stable catalytic activity for the hydrodesulfurization of thiophene while maintaining its crystal structure, except for the introduction of sulfide by replacing lattice oxygens. Pharmacosiderite Mo4P3O16 was successfully obtained by hydrothermal synthesis at a moderate temperature, and its microporosity for CO2 adsorption and catalytic properties for hydrodesulfurization were discovered.

Continuous Unsteady-State De-NOx System via Tandem Water-Gas Shift, NH3 Synthesis, and NH3-SCR under Periodic Lean/Rich Conditions.

The development of urea-free and platinum group metal (PGM)-free catalytic systems for automotive emission control is a challenging task. Herein, we report a new de-NOx system using cyclic feeds of rich and lean gas mixtures with PGM-free catalysts. Initial catalyst screening tests showed that Cu/CeO2 with 5 wt % Cu loading was the most suitable for the water-gas shift reaction (WGS, CO + H2O → CO2 + H2), followed by the selective NH3 synthesis by the NO + H2 reaction. The unsteady-state system under alternating feeds of rich (0.1% NO + 0.5% CO + 1% H2O) and lean (0.1% NO + 2% O2 + 1% H2O) gas mixtures over a mixture of Cu/CeO2 and Cr-exchanged mordenite (CrMOR) showed higher NOx conversion than the steady-state (0.1% NO + 0.35% CO + 0.6% O2 + 1% H2O) reaction between 200 and 500 °C. The de-NOx mechanism under periodical rich/lean conditions was studied by operando infrared (IR) experiments. In the rich period, the WGS reaction on the Cu/CeO2 catalyst yield H2, which reduces NO to NH3 on the Cu/CeO2 catalyst. NH3 is then captured by the Brønsted acid sites of CrMOR. In the subsequent lean period, the adsorbed NH3 acts as a reductant for the selective catalytic reduction of NOx catalyzed by the Cr sites of CrMOR. This study demonstrates a new urea-free and PGM-free catalytic system that can provide an alternative de-NOx technology for automotive catalysis under periodic rich/lean conditions.

Mechanism of NH3-SCR over P/CeO2 Catalysts Investigated by Operando Spectroscopies.

This study reports a comprehensive investigation into the active sites and reaction mechanism for the selective catalytic reduction of NO by NH3 (NH3-SCR) over phosphate-loaded ceria (P/CeO2). Catalyst characterization and density functional theory calculations reveal that H3PO4 and H2P2O6 species are the dominant phosphate species on the P/CeO2 catalysts under the experimental conditions. The reduction/oxidation half-cycles (RHC/OHC) were investigated using in situ X-ray absorption near-edge structure for Ce L3-edge, ultraviolet-visible, and infrared (IR) spectroscopies together with online analysis of outlet products (operando spectroscopy). The Ce4+(OH-) species, possibly adjacent to the phosphate species, are reduced by NO + NH3 to produce N2, H2O, and Ce3+ species (RHC). The Ce3+ species is reoxidized by aqueous O2 (OHC). The results from IR spectroscopy suggest that the RHC initiates with the reaction between NO and Ce4+(OH-) to yield Ce3+ and gaseous HONO, which then react with NH3 to produce N2 and H2O via NH4NO2 intermediates.

An automated reaction route mapping for the reaction of NO and active species on Ag4 clusters in zeolites.

A computational investigation of the catalytic reaction on multinuclear sites is very challenging. Here, using an automated reaction route mapping method, the single-component artificial force induced reaction (SC-AFIR) algorithm, the catalytic reaction of NO and OH/OOH species over the Ag42+ cluster in a zeolite is investigated. The results of the reaction route mapping for H2 + O2 reveal that OH and OOH species are formed over the Ag42+ cluster via an activation barrier lower than that of OH formation from H2O dissociation. Then, reaction route mapping is performed to examine the reactivity of the OH and OOH species with NO molecules over the Ag42+ cluster, resulting in the facile reaction path of HONO formation. With the aid of the automated reaction route mapping, the promotion effect of H2 addition on the SCR reaction was computationally proposed (boosting the formation of OH and OOH species). In addition, the present study emphasizes that automated reaction route mapping is a powerful tool to elucidate the complicated reaction pathway on multi-nuclear clusters.

In- and Ga-oxo clusters/hydrides in zeolites: speciation and catalysis for light-alkane activations/transformations.

Metal-exchanged zeolites have great potential to form unique active metal species and develop their catalysis by promoting small molecules such as light alkanes. Ga-exchanged zeolites have attracted attention as promising heterogeneous catalysts for dehydrogenative light-alkane transformations. The speciation of active Ga species in reduced and oxidized Ga-exchanged zeolites and their reaction mechanisms have been discussed in several studies based on experimental and theoretical investigations. In contrast, studies on In-exchanged zeolites have been far less explored, and thus active In-species have rarely been investigated. In this perspective, we summarized our investigations on In- and Ga-exchanged zeolites for light-alkane transformations. Our research group reported the formation of In-oxo clusters using the O2 treatment of In-CHA and their potential for the partial oxidation of CH4 (POM) at room temperature. We also observed the formation of In-hydrides in CHA zeolites during the preparation through reductive solid-state ion-exchange (RSSIE) and revealed their catalysis for non-oxidative C2H6 dehydrogenation (EDH). Their detailed structures and reaction mechanisms are discussed in combination with spectroscopic, kinetic, and theoretical studies. Furthermore, comparative studies on the formation of Ga-oxo clusters for POM at room temperature and the controlled formation of Ga-hydrides for selective EDH were conducted. The obtained results and insights are comprehensively discussed, including the relationship between the local structure of the active In/Ga species and reaction selectivity, as well as the influence of different zeolite frameworks on the formation of active species.

Super Mg2+ Conductivity around 10-3 S cm-1 Observed in a Porous Metal-Organic Framework.

We first report a solid-state crystalline "Mg2+ conductor" showing a superionic conductivity of around 10-3 S cm-1 at ambient temperature, which was obtained using the pores of a metal-organic framework (MOF), MIL-101, as ion-conducting pathways. The MOF, MIL-101⊃{Mg(TFSI)2}1.6 (TFSI- = bis(trifluoromethanesulfonyl)imide), containing Mg2+ inside its pores, showed a superionic conductivity of 1.9 × 10-3 S cm-1 at room temperature (RT) (25 °C) under the optimal guest vapor (MeCN), which is the highest value among all Mg2+-containing crystalline compounds. The Mg2+ conductivity in the MOF was estimated to be 0.8 × 10-3 S cm-1 at RT, by determining the transport number of Mg2+ (tMg2+ = 0.41), which is the level as high as practical use for secondary battery. Measurements of adsorption isotherms, pressure dependence of ionic conductivity, and in situ Fourier transform infrared measurements revealed that the "super Mg2+ conductivity" is caused by the efficient migration of the Mg2+ carrier with the help of adsorbed guest molecules.

Oxidation Catalysis over Solid-State Keggin-Type Phosphomolybdic Acid with Oxygen Defects.

Keggin-type phosphomolybdic acid (PMo12O40), treated with pyridine (Py), forms a crystalline material (PyPMo-HT) following heat treatment under an inert gas flow at ∼420 °C. Although this material is known to have attractive catalytic properties for gas-phase oxidation, the origin of this catalytic activity requires clarification. In this study, we investigated the crystal structure of PyPMo-HT. PyPMo-HT comprises a one-dimensional array of Keggin units and pyridinium cations (HPy), with an HPy/Keggin unit ratio of ∼1.0. Two oxygen atoms were removed from the Keggin unit during crystal structure transformation, which resulted in an electron being localized on the Mo atom in close contact with the adjacent Keggin unit. Upon the introduction of molecular oxygen, electron transfer from this Mo atom resulted in the formation of an electrophilic oxygen species that bridged two Keggin units. The electrophilic oxygen species acted as a catalytically active oxygen species, as confirmed by the selective oxidation of propylene. PyPMo-HT showed excellent catalytic activity for the selective oxidation of methacrolein, with the methacrylic acid yield being superior to that obtained with PMo12O40 and comparable to that obtained with an industrial Keggin-type polyoxometalate (POM) catalyst. The oxidation catalysis observed over PyPMo-HT provides a deeper understanding of POM-based industrial catalytic processes.

The reducibility and oxidation states of oxide-supported rhenium: experimental and theoretical investigations.

The activity and stability of supported metal catalysts, which exhibit high efficiency and activity, are significantly influenced by the interactions between the metal and the support, that is, metal-support interactions (MSIs). Here, we report an investigation of the MSIs between supported rhenium (Re) and oxide supports such as TiO2, SiO2, Al2O3, MgO, V2O5, and ZrO2 using experimental and computational approaches. The reducibility of the Re species was found to strongly depend on the oxide support. Experimental studies including temperature-programmed reduction by H2 as well as Re L3- and L1-edge X-ray absorption near edge structure (XANES) analysis revealed that the valency of the Re species started to decrease upon H2 reduction in the 200-400 °C range, except for Re on MgO, where the shift occurred at temperatures above 500 °C. The dependence of the Re L3- and L1-edge XANES spectra of the oxide-supported Re catalysts on the size of Re was also examined.

Surface activation by electron scavenger metal nanorod adsorption on TiH2, TiC, TiN, and Ti2O3.

Metal/oxide support perimeter sites are known to provide unique properties because the nearby metal changes the local environment on the support surface. In particular, the electron scavenger effect reduces the energy necessary for surface anion desorption, and thereby contributes to activation of the (reverse) Mars-van Krevelen mechanism. This study investigated the possibility of such activation in hydrides, carbides, nitrides, and sulfides. The work functions (WFs) of known hydrides, carbides, nitrides, oxides, and sulfides with group 3, 4, or 5 cations (Sc, Y, La, Ti, Zr, Hf, V, Nb, and Ta) were calculated. The WFs of most hydrides, carbides, and nitrides are smaller than the WF of Ag, implying that the electron scavenger effect may occur when late transition metal nanoparticles are adsorbed on the surface. The WF of oxides and sulfides decreases when reduced. The surface anion vacancy formation energy correlates well with the bulk formation energy in carbides and nitrides, while almost no correlation is found in hydrides because of the small range of surface hydrogen vacancy formation energy values. The electron scavenger effect is explicitly observed in nanorods adsorbed on TiH2 and Ti2O3; the surface vacancy formation energy decreases at anion sites near the nanorod, and charge transfer to the nanorod happens when an anion is removed at such sites. Activation of hydrides, carbides, and nitrides by nanorod adsorption and screening support materials through WF calculation are expected to open up a new category of supported catalysts.

Factors determining surface oxygen vacancy formation energy in ternary spinel structure oxides with zinc.

Spinel oxides are an important class of materials for heterogeneous catalysis including photocatalysis and electrocatalysis. The surface O vacancy formation energy (EOvac) is a critical quantity for catalyst performance because the surface of metal oxide catalysts often acts as a reaction site, for example, in the Mars-van Krevelen mechanism. However, experimental evaluation of EOvac is very challenging. We obtained the EOvac for (100), (110), and (111) surfaces of normal zinc-based spinel oxides ZnAl2O4, ZnGa2O4, ZnIn2O4, ZnV2O4, ZnCr2O4, ZnMn2O4, ZnFe2O4, and ZnCo2O4. The most stable surface is (100) for all compounds. The smallest EOvac for a surface is the largest in the (100) surface except for ZnCo2O4. For (100) and (110) surfaces, there is a good correlation, over all spinels, between the smallest EOvac for the surface and bulk formation energy, while the ionization potential correlates well in (111) surfaces. Machine learning over EOvac of all surface sites in all orientations and for all compounds to find the important factors, or descriptors, that decide the EOvac revealed that bulk and surface-dependent descriptors are the most important, namely the bulk formation energy, a Boolean descriptor of whether the surface is (111) or not, and the ionization potential, followed by geometrical descriptors that are different in each O site.

Local structure and NO adsorption/desorption property of Pd2+ cations at different paired Al sites in CHA zeolite.

Recently, Pd-exchanged CHA zeolites (Pd-CHA) have attracted attention as promising passive NOx adsorbers (PNAs) for reducing NOx emissions during the cold start period of a vehicle engine. In this work, the relationship between the local structures and the NO adsorption/desorption properties of the Pd cations in CHA zeolites was investigated. Pd cation formation and NO adsorption were theoretically explored by density functional theory (DFT) calculations for different paired Al sites in six-/eight-membered rings (6MR/8MR). Furthermore, we prepared a series of Pd-CHAs with different Pd loadings (0.5-5.4 wt%) and evaluated their NO adsorption/desorption properties by in situ infrared (IR) spectroscopy and temperature-programmed desorption (TPD) measurements. The increase in the Pd loading resulted in a shift in the NO desorption temperature toward a higher temperature regime. This phenomenon was ascribed to the increase in the proportion of less stable Pd cations, resulting in improved NO adsorption. Furthermore, the effect of Al distribution on the NO adsorption property of Pd-CHA was examined using CHA zeolites containing different proportions of paired Al sites in 6MR while maintaining similar Si/Al ratios (Si/Al = 12.0-16.5). The present study, based on a combination of theoretical and experimental techniques, shows that the NO adsorption/desorption properties over Pd-CHA can be tuned by controlling the Pd loading amount and the type of paired Al sites.

Non-oxidative Coupling of Methane: N-type Doping of Niobium Single Atoms in TiO2 -SiO2 Induces Electron Localization.

Photodriven nonoxidative coupling of CH4 (NOCM) is an attractive potential way to use abundant methane resources. Herein, an n-type doped photocatalyst for NOCM is created by doping single-atom Nb into hierarchical porous TiO2 -SiO2 (TS) microarray, which exhibits a high conversion rate of 3.57 µmol g-1 h-1 with good recyclability. The Nb dopant replaces the 6-coordinated titanium on the (1 0 1) plane and forms shallow electron-trapped surface polarons along [0 1 0] direction and the comparison of different models proves that the electron localization caused by the n-type doping is beneficial to both methane activation and ethane desorption. The positive effect of n-type dopant on CH4 conversion is further verified on Mo-, W- and Ta-doped composites. In contrast, the doping of p-type dopant (Ga, Cu, Fe) shows a less active influence.

Isolated Indium Hydrides in CHA Zeolites: Speciation and Catalysis for Nonoxidative Dehydrogenation of Ethane.

The study of the formation, characterization, and functionality of isolated surface hydrides on solid materials is a formidable task because of the complexity of solid surfaces and the difficulty of analyzing structures in solids. Herein, we found the formation of indium (In) hydride species supported by CHA zeolites. The In hydrides were formed by treatment of an In-exchanged CHA zeolite (In-CHA) with H2 at high temperatures (>773 K). In situ Fourier transform infrared (FTIR) spectroscopy and density functional theory (DFT) calculations revealed that an [InH2]+ ion on a framework anionic site is a plausible structure. In-CHA exhibited high selectivity and durable catalytic activity for the nonoxidative dehydrogenation of ethane for at least 90 h. Kinetic and in situ spectroscopic studies as well as transition state (TS) calculations suggested that [InH2]+ ions serve as catalytically active sites for selective dehydrogenation using In-CHA.

Direct Phenolysis Reactions of Unactivated Amides into Phenolic Esters Promoted by a Heterogeneous CeO2 Catalyst.

The direct catalytic esterification of amides that leads to the construction of C-O bonds through the cleavage of amide C-N bonds is a highly attractive strategy in organic synthesis. While aliphatic and aromatic alcohols can be readily used for the alcoholysis of activated and unactivated amides, the introduction of phenols is more challenging due to their lower nucleophilicity in the phenolysis of unactivated amides. Herein, we demonstrate that phenols can be used for the phenolysis of unactivated amides into the corresponding phenolic esters using a simple heterogenous catalytic system based on CeO2 under additive-free reaction conditions. The method tolerates a broad variety of functional groups (>50 examples) in the substrates. Results of kinetic studies afforded mechanistic insights into the principles governing this reaction, suggesting that the cooperative effects of the acid-base functions of catalysts would be of paramount importance for the efficient progression of the C-N bond breaking process, and consequently, CeO2 showed the best catalytic performance among the catalysts explored.

Experimental and theoretical study of multinuclear indium-oxo clusters in CHA zeolite for CH4 activation at room temperature.

We have carried out an experimental and theoretical study of CHA-zeolite supported indium (In)-oxo clusters that promote CH4 activation at room temperature. X-ray absorption fine structure (XAFS) measurements indicate the formation of multinuclear In-oxo clusters by the O2 activation of the In(i)-exchanged CHA zeolite prepared through reductive solid-state ion exchange (RSSIE). The structure of the In-oxo clusters and their locations were investigated in detail using ab initio thermodynamic analysis. The redox properties of the In species during RSSIE and the formation of the In-oxo clusters were also studied by temperature programmed reaction and in situ XAFS measurements. The reaction of CH4 on the O2-activated In-CHA zeolite was monitored using IR spectroscopy where adsorbed formic acid was generated at room temperature. The adsorption and C-H activation of CH4 on our plausible model of the In-oxo clusters were theoretically investigated using density functional theory calculations. We found that CH4 is likely to adsorb and react more easily on dinuclear In-oxo ions than on monomeric In-oxo ions and that the C-H bond cleavage reaction occurs via a heterolytic pathway rather than a homolytic pathway. This study reveals the potential of multinuclear In-oxo clusters as active sites for the transformation of CH4 to oxygenates under mild reaction conditions.

MOF-on-MOF: Oriented Growth of Multiple Layered Thin Films of Metal-Organic Frameworks.

The precise alignment of multiple layers of metal-organic framework (MOF) thin films, or MOF-on-MOF films, over macroscopic length scales is presented. The MOF-on-MOF films are fabricated by epitaxially matching the interface. The first MOF layer (Cu2 (BPDC)2 , BPDC=biphenyl-4,4'-dicarboxylate) is grown on an oriented Cu(OH)2 film by a "one-pot" approach. Aligned second (Cu2 (BDC)2 , BDC=benzene 1,4-dicarboxylate, or Cu2 (BPYDC)2 , BPYDC=2,2'-bipyridine-5,5'-dicarboxylate) MOF layers can be deposited using liquid-phase epitaxy. The co-orientation of the MOF films is confirmed by X-ray diffraction. Importantly, our strategy allows for the synthesis of aligned MOF films, for example, Cu2 (BPYDC)2 , that cannot be grown on a Cu(OH)2 surface. We show that aligned MOF films furnished with Ag nanoparticles show a unique anisotropic plasmon resonance. Our MOF-on-MOF approach expands the chemistry of heteroepitaxially oriented MOF films and provides a new toolbox for multifunctional porous coatings.

Origin of Nb2 O5 Lewis Acid Catalysis for Activation of Carboxylic Acids in the Presence of a Hard Base.

The Nb2 O5 surface catalyzes the amidation of carboxylic acids with amines through Nb5+ Lewis acid activation of the C=O group. In this work, DFT calculations were applied to theoretically investigate the C=O bond activation of a model carboxylic acid (acetic acid) on θ-Al2 O3 (110), anatase TiO2 (101), and T-Nb2 O5 (100) surfaces. The adsorption sites, adsorption energies, reaction energy barriers, electronic properties, and vibrational frequency of acetic acid were examined in detail. It was found that the bond activation of the carbonyl group is most efficient on Nb2 O5 , although the adsorption energy is larger on Al2 O3 and TiO2 . The most efficient C=O bond activation on Nb2 O5 results in the lowest energy barrier of C-N bond formation during amidation. The Nb2 O5 surface also shows larger tolerance to methylamine and water molecules than Al2 O3 and TiO2 surfaces. These crucial factors contribute to the highest amidation catalytic reactivity on Nb2 O5 . Furthermore, the position of the mean density of states of the d-conduction band of the active metal site relative to the Fermi energy level correlates well with the efficiency in the C=O bond activation and, consequently, the catalytic activity for amidation. These results suggest that, unlike a classical understanding of strong acid sites of metal oxide surfaces, interaction of a carbonyl HOMO with an unoccupied metal d-orbital, or, in other words, covalent-like interaction between a carbonyl group and metal adsorption site, is relevant to the present system.

The Catalytic Reduction of Carboxylic Acid Derivatives and CO2 by Metal Nanoparticles on Lewis-Acidic Supports.

The development of heterogeneous catalysts for green chemical synthesis is currently a growing area in catalysis and sustainable chemistry. Especially the use of renewable carbon resources such as carbon dioxide (CO2 ) and biomass-derived compounds (e. g. carboxylic acids, esters, and amides) represent highly attractive research targets. As these substances reside in a high oxidation state, efficient reduction processes are required in order to convert these substrates into useful and value-added chemicals. Moreover, in the interest of mass production, these substrates should be reduced by molecular H2 and a heterogeneous catalyst. In this context, our group has developed advanced catalysts and established design guidelines for catalysts that promote the reductive transformations of carboxylic acid derivatives and CO2 . Our studies show that cooperative catalysis between Lewis-acidic sites on the catalyst support and supported metal nanoparticles are crucial for the success of these challenging hydrogenations. In this review, we summarize the results of our recent studies on the direct synthesis of value-added chemicals from CO2 and carboxylic acid derivatives using supported transition-metal catalysts, and we propose a design concept for heterogeneous catalysts that promote these processes.