Mixed proton and electron conducting double perovskite anodes for stable and efficient tubular proton ceramic electrolysers.

Hydrogen production from water electrolysis is a key enabling energy storage technology for the large-scale deployment of intermittent renewable energy sources. Proton ceramic electrolysers (PCEs) can produce dry pressurized hydrogen directly from steam, avoiding major parts of cost-driving downstream separation and compression. However, the development of PCEs has suffered from limited electrical efficiency due to electronic leakage and poor electrode kinetics. Here, we present the first fully operational BaZrO3-based tubular PCE, with 10 cm2 active area and a hydrogen production rate above 15 Nml min-1. The novel steam anode Ba1-xGd0.8La0.2+xCo2O6-δ exhibits mixed p-type electronic and protonic conduction and low activation energy for water splitting, enabling total polarization resistances below 1 Ω cm2 at 600 °C and Faradaic efficiencies close to 100% at high steam pressures. These tubular PCEs are mechanically robust, tolerate high pressures, allow improved process integration and offer scale-up modularity.

Metal-Doping of La5.4MoO11.1 Proton Conductors: Impact on the Structure and Electrical Properties.

La5.4MoO11.1 proton conductors with different metal doping (Ca2+, Sr2+, Ba2+, Ti4+, Zr4+, and Nb5+) have been prepared and structurally and electrically characterized. Different polymorphs are stabilized depending on the doping and cooling rate used during the synthesis process. The most interesting results are obtained for Nb-doping, La5.4Mo1- xNb xO11.1- x/2, where single compounds are obtained in the compositional range 0 ≤ x ≤ 0.2. These materials are fully characterized by structural techniques such as X-ray and neutron powder diffraction and transmission electron microscopy, which independently confirm the changes of polymorphism. Scanning electron microscopy and impedance spectroscopy measurements in dry/wet gases (N2, O2, and 5% H2-Ar) showed an enhancement of the sinterability and electrical properties of the materials after Nb-doping. Conductivity measurements under very reducing conditions revealed that these materials are mixed ionic-electronic conductors, making them potential candidates for hydrogen separation membranes.

The influence of acceptor and donor doping on the protonic surface conduction of TiO2.

The transport of protonic charge carriers along and within the pore surfaces of porous oxide matrices is of significant importance for many catalytic and electrochemical applications, with porous TiO2 being a candidate material both for photocatalytic applications and as an electronically conducting support for polymer-based electrochemical cells. This work investigates the effect of acceptor (Cr and Fe) and donor (Nb) doping on protonic surface conduction in porous TiO2 over a wide range of relative humidity, temperature and oxygen activity. Generally, we find that acceptor dopants on the surface counteract dissociation and reduce the mobility of protons, while donor dopants give rise to enhanced dissociation making protonic surface conduction the highest for donor-doped samples, contrary to conventional bulk proton conductors. Moreover, protonic surface conduction in Cr-doped TiO2 is significantly higher under oxidising conditions compared to reducing conditions, which we relate to the presence of a higher valent species such as Cr6+ on the surface under oxidising conditions, again emphasising that protonic surface conduction increases with higher-valent (donor) and more acidic cations present on the surface.

First observation of surface protonics on SrZrO3 perovskite under a H2 atmosphere.

This is the first direct observation that surface proton hopping occurs on SrZrO3 perovskite even under a H2 (i.e. dry) atmosphere. Understanding proton conduction mechanisms on ceramic surfaces under a H2 atmosphere is necessary to investigate the role of proton hopping on the surface of heterogeneous catalysts in an electric field. In this work, surface protonics was investigated using electrochemical impedance spectroscopy (EIS). To extract the surface proton conduction, two pellets of different relative densities were prepared: a porous sample (R.D. = 60%) and a dense sample (R.D. = 90%). Comparison of conductivities with and without H2 revealed that only the porous sample showed a decrease in the apparent activation energy of conductivity by supplying H2. H/D isotope exchange tests revealed that the surface proton is the dominant conductive species over the porous sample with H2 supply. Such identification of a dominant conductive carrier facilitates consideration of the role of surface protonics in chemical reactions.