The 1,3-Dioctadecyl-1H-imidazol-3-ium Based Potentiometric Surfactant Sensor for Detecting Cationic Surfactants in Commercial Products.

A low-cost and fast potentiometric surfactant sensor for cationic surfactants, based on the new ion-pair 1,3-dioctadecyl-1H-imidazol-3-ium-tetraphenylborate (DODI-TPB), is presented. The new cationic surfactant DODI-Br was synthesized and characterized by NMR, LC-MS, and elemental analysis, and was used for synthesis of the DODI-TPB ionophore. The DODI-TPB surfactant sensor was obtained by implementation of the ionophore in PVC. The sensor showed excellent response characteristics with near-Nernstian slopes to the cationic surfactants DMIC, CPC, CTAB, and Hyamine 1622. The highest voltage responses were obtained for DMIC and CPC (58.7 mV/decade of activity). DMIC had the lowest detection limit (0.9 × 10-6 M) and the broadest useful linear concentration range (1.8 × 10-6 to 1.0 × 10-4 M). An interference study showed remarkable stability. Potentiometric titration curves for the titration of cationic surfactants (DMIC, CPC, CTAB, and Hyamine 1622), with DDS and TPB used as titrants, showed sigmoidal curves with well-defined inflexion points and a broad signal change. The standard addition method was successfully applied with recovery rates from 98.9 to 101.2 at two concentrations. The amount of cationic surfactant found in disinfectants and antiseptics was in good agreement with the referent two-phase titration method and the surfactant sensor on the market. This new surfactant sensor represents a low-cost alternative to existing methods for cationic surfactant detection.

Loading of Polydimethylsiloxane with a Human ApoB-Derived Antimicrobial Peptide to Prevent Bacterial Infections.

BACKGROUND: medical device-induced infections affect millions of lives worldwide and innovative preventive strategies are urgently required. Antimicrobial peptides (AMPs) appear as ideal candidates to efficiently functionalize medical devices surfaces and prevent bacterial infections. In this scenario, here, we produced antimicrobial polydimethylsiloxane (PDMS) by loading this polymer with an antimicrobial peptide identified in human apolipoprotein B, r(P)ApoBLPro. METHODS: once obtained loaded PDMS, its structure, anti-infective properties, ability to release the peptide, stability, and biocompatibility were evaluated by FTIR spectroscopy, water contact angle measurements, broth microdilution method, time-killing kinetic assays, quartz crystal microbalance analyses, MTT assays, and scanning electron microscopy analyses. RESULTS: PDMS was loaded with r(P)ApoBLPro peptide which was found to be present not only in the bulk matrix of the polymer but also on its surface. ApoB-derived peptide was found to retain its antimicrobial properties once loaded into PDMS and the antimicrobial material was found to be stable upon storage at 4 °C for a prolonged time interval. A gradual and significant release (70% of the total amount) of the peptide from PDMS was also demonstrated upon 400 min incubation and the antimicrobial material was found to be endowed with anti-adhesive properties and with the ability to prevent biofilm attachment. Furthermore, PDMS loaded with r(P)ApoBLPro peptide was found not to affect the viability of eukaryotic cells. CONCLUSIONS: an easy procedure to functionalize PDMS with r(P)ApoBLPro peptide has been here developed and the obtained functionalized material has been found to be stable, antimicrobial, and biocompatible.

Fluorescence Emission of Self-assembling Amyloid-like Peptides: Solution versus Solid State.

Analysis of the intrinsic UV-visible fluorescence exhibited by self-assembling amyloid-like peptides in solution and in solid the state highlights that their physical state has a profound impact on the optical properties. In the solid state, a linear dependence of the fluorescence emission peaks as a function of excitation wavelength is detected. On the contrary, an excitation-independent emission is observed in solution. The present findings constitute a valuable benchmark for current and future explanations of the fluorescence emission by amyloids.

Randomly positioned gold nanoparticles as fluorescence enhancers in apta-immunosensor for malaria test.

A plasmon-enhanced fluorescence-based antibody-aptamer biosensor - consisting of gold nanoparticles randomly immobilized onto a glass substrate via electrostatic self-assembly - is described for specific detection of proteins in whole blood. Analyte recognition is realized through a sandwich scheme with a capture bioreceptor layer of antibodies - covalently immobilized onto the gold nanoparticle surface in upright orientation and close-packed configuration by photochemical immobilization technique (PIT) - and a top bioreceptor layer of fluorescently labelled aptamers. Such a sandwich configuration warrants not only extremely high specificity, but also an ideal fluorophore-nanostructure distance (approximately 10-15 nm) for achieving strong fluorescence amplification. For a specific application, we tested the biosensor performance in a case study for the detection of malaria-related marker Plasmodium falciparum lactate dehydrogenase (PfLDH). The proposed biosensor can specifically detect PfLDH in spiked whole blood down to 10 pM (0.3 ng/mL) without any sample pretreatment. The combination of simple and scalable fabrication, potentially high-throughput analysis, and excellent sensing performance provides a new approach to biosensing with significant advantages compared to conventional fluorescence immunoassays.

Screen Printed Based Impedimetric Immunosensor for Rapid Detection of Escherichia coli in Drinking Water.

The development of a simple and low cost electrochemical impedance immunosensor based on screen printed gold electrode for rapid detection of Escherichia coli in water is reported. The immunosensor is fabricated by immobilizing anti-E. coli antibodies onto a gold surface in a covalent way by the photochemical immobilization technique, a simple procedure able to bind antibodies upright onto gold surfaces. Impedance spectra are recorded in 0.01 M phosphate buffer solution (PBS) containing 10 mM Fe(CN)63-/Fe(CN)64- as redox probe. The Nyquist plots can be modelled with a modified Randles circuit, identifying the charge transfer resistance Rct as the relevant parameter after the immobilization of antibodies, the blocking with BSA and the binding of E. coli. The introduction of a standard amplification procedure leads to a significant enhancement of the impedance increase, which allows one to measure E. coli in drinking water with a limit of detection of 3 × 101 CFU mL-1 while preserving the rapidity of the method that requires only 1 h to provide a "yes/no" response. Additionally, by applying the Langmuir adsorption model, we are able to describe the change of Rct in terms of the "effective" electrode, which is modified by the detection of the analyte whose microscopic conducting properties can be quantified.

Biosensor surface functionalization by a simple photochemical immobilization of antibodies: experimental characterization by mass spectrometry and surface enhanced Raman spectroscopy.

Surface functionalization is a key step in biosensing since it is the basis of an effective analyte recognition. Among all the bioreceptors, antibodies (Abs) play a key role thanks to their superior specificity, although the available immobilization strategies suffer from several drawbacks. When gold is the interacting surface, the recently introduced Photochemical Immobilization Technique (PIT) has been shown to be a quick, easy-to-use and very effective method to tether Abs oriented upright by means of thiols produced via tryptophan mediated disulphide bridge reduction. Although the molecular mechanism of this process is quite well identified, the detailed morphology of the immobilized antibodies is still elusive due to inherent difficulties related to the microscopy imaging of Abs. The combination of Mass Spectrometry, Surface-Enhanced Raman Spectroscopy and Ellman's assay demonstrates that Abs irradiated under the conditions in which PIT is realized show only two effective disulphide bridges available for binding. They are located in the constant region of the immunoglobulin light chain so that the most likely position Ab assumes is side-on, i.e. with one Fab (i.e. the antigen binding portion of the antibody) exposed to the solution. This is not a limitation of the recognition efficiency in view of the intrinsic flexibility of the Ab structure, which makes the free Fab able to sway in the solution, a feature of great importance in many biosensing applications.

A multi-scale time-resolved study of photoactivated dynamics in 5-benzyl uracil, a model for DNA/protein interactions.

We combine fluorescence up-conversion and time correlated single photon counting experiments to investigate the 5-benzyl uracil excited state dynamics in methanol from 100 fs up to several ns. This molecule has been proposed as a model for DNA/protein interactions. Our results show emission bands at about 310 and 350 nm that exhibit bi-exponential sub-ps decays. Calculations, including solvent effects by a mixed discrete-continuum model, indicate that the Franck Condon region is characterized by significant coupling between the excited states of the benzyl and the uracil moieties, mirrored by the short-lived emission at 310 nm. Two main ground state recovery pathways are identified, both contributing to the 350 nm emission. The first 'photophysical' decay path involves a ππ* excited state localized on the uracil and is connected to the ground electronic state by an easily accessible crossing with S0, accounting for the short lifetime component. Simulations indicate that a possible second pathway is characterized by exciplex formation, with partial benzene → uracil charge transfer character, that may lead instead to photocyclization. The relevance of our results is discussed in view of the photoactivated dynamics of DNA/protein complexes, with implications on their interaction mechanisms.

Self-Assembling of Fmoc-GC Peptide Nucleic Acid Dimers into Highly Fluorescent Aggregates.

The study of molecules that self-assemble through noncovalent interactions is one of the most attractive topics in supramolecular chemistry. The use of short peptides or modified nucleotides as building blocks for the aggregates is particularly intriguing because these are very easy to synthesize; moreover, subtle changes in the chemical structure of such building blocks may drastically affect the properties of the aggregates. The ability of peptide nucleic acids (PNA) to aggregate has been very little explored, despite its practical applications. In this work we investigated the self-assembling properties of a PNA dimer, conjugated at the N-terminus to a fluorenylmethoxycarbonyl group. This PNA dimer forms nano-aggregates at low concentration in CHCl3 /CH3 OH mixtures. The aggregates retain very interesting fluorescent properties (high quantum yield in the visible region with lifetimes on the nanosecond scale), which make them promising materials for applications in optoelectronics.

Vmh2 hydrophobin as a tool for the development of "self-immobilizing" enzymes for biosensing.

Self-assembling proteins forming amyloid fibrils are promising candidates for the fabrication of biomaterials, due to the chemical and mechanical stability of their structures. Among potential applications, their use as platforms for enzyme immobilization is rapidly gathering attention. In this work, we demonstrate that the production of the enzyme glutathione-S-transferase (GST) fused to the class I hydrophobin Vmh2 from Pleurotus ostreatus represents an invaluable tool for the development of self-immobilizing enzymes useful for high throughput analyses. The proposed immobilization strategy is versatile since it can be applied, in principle, to every recombinant protein able to refold from Escherichia coli inclusion bodies. A GST based biosensor has been developed to quantify toxic compounds, such as the pesticides molinate and captan, in aqueous environmental samples. The main advantages of this sensor include simplicity and speed of preparation, high sensitivity, reusability, and accuracy. Biotechnol. Bioeng. 2017;114: 46-52. © 2016 Wiley Periodicals, Inc.

Femtosecond UV-laser pulses to unveil protein-protein interactions in living cells.

A hallmark to decipher bioprocesses is to characterize protein-protein interactions in living cells. To do this, the development of innovative methodologies, which do not alter proteins and their natural environment, is particularly needed. Here, we report a method (LUCK, Laser UV Cross-linKing) to in vivo cross-link proteins by UV-laser irradiation of living cells. Upon irradiation of HeLa cells under controlled conditions, cross-linked products of glyceraldehyde-3-phosphate dehydrogenase (GAPDH) were detected, whose yield was found to be a linear function of the total irradiation energy. We demonstrated that stable dimers of GAPDH were formed through intersubunit cross-linking, as also observed when the pure protein was irradiated by UV-laser in vitro. We proposed a defined patch of aromatic residues located at the enzyme subunit interface as the cross-linking sites involved in dimer formation. Hence, by this technique, UV-laser is able to photofix protein surfaces that come in direct contact. Due to the ultra-short time scale of UV-laser-induced cross-linking, this technique could be extended to weld even transient protein interactions in their native context.

Detection of parathion pesticide by quartz crystal microbalance functionalized with UV-activated antibodies.

Photonic immobilization technique (PIT) has been used to develop an immunosensor for the detection of parathion. An antibody solution has been activated by breaking the disulfide bridge in the triad Trp/Cys-Cys through absorption of ultrashort UV laser pulses. The free thiol groups so produced interact with gold lamina making the antibody oriented upside, that is, with its variable parts exposed to the environment, thereby greatly increasing the detection efficiency. PIT has been applied to anchor polyclonal antiparathion antibodies to the gold electrode of a Quartz Crystal Microbalance (QCM) giving rise to very high detection sensitivity once the parathion is made heavier by complexion with BSA (bovine serum albumin), this latter step only required by the mass based transducer used in this case. The comparison of the sensor response with irradiated antibodies against different analytes shows that the high degree of antibody specificity is not affected by PIT nor is it by the complexion of parathion with BSA. These results pave the way to important applications in biosensing, since the widespread occurrence of the Trp/Cys-Cys residues triads in proteins make our procedure very general and effective to detect light analytes.

Influence of generalized focusing of few-cycle Gaussian pulses in attosecond pulse generation.

In contrast to the case of quasi-monochromatic waves, a focused optical pulse in the few-cycle limit may exhibit two independent curved wavefronts, associated with phase and group retardations, respectively. Focusing optical elements will generally affect these two wavefronts differently, thus leading to very different behavior of the pulse near focus. As limiting cases, we consider an ideal diffractive lens introducing only phase retardations and a perfect non-dispersive refractive lens (or a curved mirror) introducing equal phase and group retardations. We study the resulting diffraction effects on the pulse, finding both strong deformations of the pulse shape and shifts in the spectrum. We then show how important these effects can be in highly nonlinear optics, by studying their role in attosecond pulse generation. In particular, the focusing effects are found to affect substantially the generation of isolated attosecond pulses in gases from few-cycle fundamental optical fields.

Ultraviolet laser-induced cross-linking in peptides.

RATIONALE: The aim of this study was to demonstrate, and to characterize by high-resolution mass spectrometry that it is possible to preferentially induce covalent cross-links in peptides by using high-energy femtosecond ultraviolet (UV) laser pulses. The cross-link is readily formed only when aromatic amino acids are present in the peptide sequence. METHODS: Three peptides, xenopsin, angiotensin I, and interleukin, individually or in combination, were exposed to high-energy femtosecond UV laser pulses, either alone or in the presence of spin trapping molecules, the reaction products being characterized by high resolution mass spectrometry. RESULTS: High-resolution mass spectrometry and spin trapping strategies showed that cross-linking occurs readily, proceeds via a radical mechanism, and is the highly dominant reaction, proceeding without causing significant photo-damage in the investigated range of experimental parameters. CONCLUSIONS: High-energy femtosecond UV laser pulses can be used to induce covalent cross-links between aromatic amino acids in peptides, overcoming photo-oxidation processes, that predominate as the mean laser pulse intensity approaches illumination conditions achievable with conventional UV light sources.

Analysis of simulated fluorescence intensities decays by a new maximum entropy method algorithm.

A new algorithm for the Maximum Entropy Method (MEM) is proposed for recovering the lifetime distribution in time-resolved fluorescence decays. The procedure is based on seeking the distribution that maximizes the Skilling entropy function subjected to the chi-squared constraint χ(2) ~ 1 through iterative linear approximations, LU decomposition of the Hessian matrix of the lagrangian problem and the Golden Section Search for backtracking. The accuracy of this algorithm has been investigated through comparisons with simulated fluorescence decays both of narrow and broad lifetime distributions. The proposed approach is capable to analyse datasets of up to 4,096 points with a discretization ranging from 100 to 1,000 lifetimes. A good agreement with non linear fitting estimates has been observed when the method has been applied to multi-exponential decays. Remarkable results have been also obtained for the broad lifetime distributions where the position is recovered with high accuracy and the distribution width is estimated within 3%. These results indicate that the procedure proposed generates MEM lifetime distributions that can be used to quantify the real heterogeneity of lifetimes in a sample.

Low-lying excited-states of 5-benzyluracil.

A numerical study is reported concerning the first and second singlet excited-states of 5-benzyluracil using the multireference self-consistent field (state-averaged CASSCF) method. The vertical excitation energies of low-lying excited-states were characterized using the SA-CASSCF method, as well as using higher-level methods, such as CASPT2, MRCI and EOM-CCSD. The local minima and conical intersections found on the potential energy surfaces (PESs) were characterized in terms of molecular geometry and natural population analysis. Different relaxation pathways on the PESs are identified and discussed by comparing with the similar pathways found for the individual monomers of uracil and benzene. The molecule can be thought of as a model system for the study of crosslink reaction between DNA and proteins induced by UV light.

A Neural Network Model Combining [-2]proPSA, freePSA, Total PSA, Cathepsin D, and Thrombospondin-1 Showed Increased Accuracy in the Identification of Clinically Significant Prostate Cancer.

BACKGROUND: The Prostate Health Index (PHI) and Proclarix (PCLX) have been proposed as blood-based tests for prostate cancer (PCa). In this study, we evaluated the feasibility of an artificial neural network (ANN)-based approach to develop a combinatorial model including PHI and PCLX biomarkers to recognize clinically significant PCa (csPCa) at initial diagnosis. METHODS: To this aim, we prospectively enrolled 344 men from two different centres. All patients underwent radical prostatectomy (RP). All men had a prostate-specific antigen (PSA) between 2 and 10 ng/mL. We used an artificial neural network to develop models that can identify csPCa efficiently. As inputs, the model uses [-2]proPSA, freePSA, total PSA, cathepsin D, thrombospondin, and age. RESULTS: The output of the model is an estimate of the presence of a low or high Gleason score PCa defined at RP. After training on a dataset of up to 220 samples and optimization of the variables, the model achieved values as high as 78% for sensitivity and 62% for specificity for all-cancer detection compared with those of PHI and PCLX alone. For csPCa detection, the model showed 66% (95% CI 66-68%) for sensitivity and 68% (95% CI 66-68%) for specificity. These values were significantly different compared with those of PHI (p < 0.0001 and 0.0001, respectively) and PCLX (p = 0.0003 and 0.0006, respectively) alone. CONCLUSIONS: Our preliminary study suggests that combining PHI and PCLX biomarkers may help to estimate, with higher accuracy, the presence of csPCa at initial diagnosis, allowing a personalized treatment approach. Further studies training the model on larger datasets are strongly encouraged to support the efficiency of this approach.

Magnetic micromixing for highly sensitive detection of glyphosate in tap water by colorimetric immunosensor.

Glyphosate is the most widely used herbicide in the world and, in view of its toxicity, there is a quest for easy-to-use, but reliable methods to detect it in water. To address this issue, we realized a simple, rapid, and highly sensitive immunosensor based on gold coated magnetic nanoparticles (MNPs@Au) to detect glyphosate in tap water. Not only the gold shell provided a sensitive optical transduction of the biological signal - through the shift of the local surface plasmon resonance (LSPR) entailed by the nanoparticle aggregation -, but it also allowed us to use an effective photochemical immobilization technique to tether oriented antibodies straight on the nanoparticles surface. While such a feature led to aggregates in which the nanoparticles were at close proximity each other, the magnetic properties of the core offered us an efficient tool to steer the nanoparticles by a rotating magnetic field. As a result, the nanoparticle aggregation in presence of the target could take place at higher rate (enhanced diffusion) with significant improvement in sensitivity. As a matter of fact, the combination of plasmonic and magnetic properties within the same nanoparticles allowed us to realize a colorimetric biosensor with a limit of detection (LOD) of 20 ng∙L-1.

Advances and emerging challenges in MXenes and their nanocomposites for biosensing applications.

Two-dimensional materials have unique properties and their better functionality has created new paradigms in the field of sensing. Over the past decade, a new family of 2D materials known as MXenes has emerged as a promising material for numerous applications, including biosensing. Their metallic conductivity, rich surface chemistry, hydrophilicity, good biocompatibility, and high anchoring capacity for biomaterials make them an attractive candidate to detect a variety of analytes. Despite such notable properties, there are certain limitations associated with them. This review aims to present a detailed survey of MXene's synthesis; in particular, their superiority in the field of biosensing as compared to other 2D materials is addressed. Their low oxidative stability is still an open challenge, and recent investigations on MXene's oxidation are summarized. The hexagonal stacking network of MXenes acts as a distinctive matrix to load nanoparticles, and the embedded nanoparticles can bind an excess number of biomolecules (e.g., antibodies) thereby improving biosensor performance. We will also discuss the synthesis and corresponding performance of MXenes nanocomposites with noble metal nanoparticles and magnetic nanoparticles. Furthermore, Nb and Ti2C-based MXenes, and Ti3C2-MXene sandwich immunoassays are also reviewed in view of their importance. Different aspects and challenges associated with MXenes (from their synthesis to final applications) and the future perspectives described give new directions to fabricate novel biosensors.

Double-Resonant Nanostructured Gold Surface for Multiplexed Detection.

A novel double-resonant plasmonic substrate for fluorescence amplification in a chip-based apta-immunoassay is herein reported. The amplification mechanism relies on plasmon-enhanced fluorescence (PEF) effect. The substrate consists of an assembly of plasmon-coupled and plasmon-uncoupled gold nanoparticles (AuNPs) immobilized onto a glass slide. Plasmon-coupled AuNPs are hexagonally arranged along branch patterns whose resonance lies in the red band (∼675 nm). Plasmon-uncoupled AuNPs are sprinkled onto the substrate, and they exhibit a narrow resonance at 524 nm. Numerical simulations of the plasmonic response of the substrate through the finite-difference time-domain (FDTD) method reveal the presence of electromagnetic hot spots mainly confined in the interparticle junctions. In order to realize a PEF-based device for potential multiplexing applications, the plasmon resonances are coupled with the emission peak of 5-carboxyfluorescein (5-FAM) fluorophore and with the excitation/emission peaks of cyanine 5 (Cy5). The substrate is implemented in a malaria apta-immunoassay to detect Plasmodium falciparum lactate dehydrogenase (PfLDH) in human whole blood. Antibodies against Plasmodium biomarkers constitute the capture layer, whereas fluorescently labeled aptamers recognizing PfLDH are adopted as the top layer. The fluorescence emitted by 5-FAM and Cy5 fluorophores are linearly correlated (logarithm scale) to the PfLDH concentration over five decades. The limits of detection are 50 pM (1.6 ng/mL) with the 5-FAM probe and 260 fM (8.6 pg./mL) with the Cy5 probe. No sample preconcentration and complex pretreatments are required. Average fluorescence amplifications of 160 and 4500 are measured in the 5-FAM and Cy5 channel, respectively. These results are reasonably consistent with those worked out by FDTD simulations. The implementation of the proposed approach in multiwell-plate-based bioassays would lead to either signal redundancy (two dyes for a single analyte) or to a simultaneous detection of two analytes by different dyes, the latter being a key step toward high-throughput analysis.

Solid-state optical properties of self-assembling amyloid-like peptides with different charged states at the terminal ends.

The self-assembling of small peptides not only leads to the formation of intriguing nanoarchitectures, but also generates materials with unexpected functional properties. Oligopeptides can form amyloid-like cross-ß assemblies that are able to emit intrinsic photoluminescence (PL), over the whole near-UV/visible range, whose origin is still largely debated. As proton transfer between the peptide chain termini within the assembly is one of the invoked interpretations of this phenomenon, we here evaluated the solid state PL properties of a series of self-assembled hexaphenylalanine peptides characterized by a different terminal charge state. Overall, our data indicate that the charge state of these peptides has a marginal role in the PL emission as all systems exhibit very similar multicolour PL associated with a violation of the Kasha's rule. On the other hand, charged/uncharged ends occasionally produce differences in the quantum yields. The generality of these observations has been proven by extending these analyses to the Aß16-21 peptide. Collectively, the present findings provide useful information for deciphering the code that links the spectroscopic properties of these assemblies to their structural/electronic features.