CAD-CAM and analog occlusal splints comparison based on the amount of occlusal adjustments. 3D analysis of the volumetric changes: A pilot study.

OBJECTIVE: To evaluate the volumetric changes on occlusal surface of computer-aided design and computer-aided manufacturing (CAD-CAM) occlusal devices fabricated following a fully digital workflow after occlusal adjustment, compared to those fabricated with an analog workflow. MATERIALS AND METHODS: Eight participants were included in this clinical pilot study, receiving two different occlusal devices fabricated with two different workflows, fully analog and fully digital. Every occlusal device was scanned before and after the occlusal adjustments to compare the volumetric changes using a reverse engineering software program. Moreover, three independent evaluators assessed a semi-quantitative and qualitative comparison using visual analog scale and dichotomous evaluation. The Shapiro-Wilk test was performed to validate normal distribution assumption, and a dependent t-Student test for paired variables was used to determine statistically significant differences (p-value < 0.05). RESULTS: The root mean square value was extracted from the 3-Dimensional (3D) analysis of the occlusal devices. The average values of the root mean square were higher for the analogic technique (0.23 ± 0.10 mm) than the digital technique (0.14 ± 0.07 mm) but the differences were not statistically significant (paired t-Student test; p = 0.106) between the two fabrication techniques. The semiquantitative visual analog scale values between the impression for the digital (5.08 ± 2.4 cm) and analog (3.80 ± 3.3 cm) technique were significant (p < 0.001), and statistically significant differences values were assessed for evaluator 3 compared to the other evaluators (p < 0.05). However, the three evaluators agreed on the qualitative dichotomous evaluation in 62% of the cases, and at least two evaluators agreed in 100% of the evaluations. CONCLUSIONS: Occlusal devices fabricated following a fully digital workflow resulted in fewer occlusal adjustments, as they could be a valid alternative to those fabricated following an analog workflow. CLINICAL SIGNIFICANCE: Fabricated occlusal devices following a fully digital workflow could have some advantages over analog workflow such reduce occlusal adjustments at delivery appointment, which can result in reduced chair time and therefore increased comfort for the patient and clinician.

A fully digital protocol to provide a fixed interim complete denture for immediate loading for a completely edentulous patient: A dental technique.

Complete arch immediate-loading implant-supported prostheses can represent a major challenge for the patient and the dental team. Obtaining stable references and an accurate occlusal record after implant placement to provide an interim prosthesis is a difficult task and can deviate from the initial treatment plan. The described technique presents a fully digital protocol to provide an immediate complete arch implant-supported fixed interim prosthesis for edentulous patients by making postoperative cone beam computed tomography and intraoral digital scans that correlate with the previous plan.

Computer-aided design and computer-aided manufacturing poly (methyl methacrylate) interim veneers for immediate esthetic restoration of autotransplanted teeth.

Autotransplanted teeth in the maxillary anterior region should be restored or reshaped as soon as possible for functional and esthetic reasons as well as the well-being of the patient. However, such tooth restorations are frequently not carried out immediately after tooth transplantation because the process could have a negative impact on the healing process. The development of a simple, immediate, and atraumatic esthetic interim restoration would be of great benefit to both the clinician and patient and address all the concerns caused by immediately preparing the tooth postoperatively and cementing a permanent restoration. This report describes the use of CAD-CAM technology to create poly (methyl methacrylate) veneers preoperatively that can be cemented extraorally on the extracted donor tooth for the immediate and interim recontouring of autotransplanted anterior teeth.

Fabrication of a CAD-CAM combination matrix for trial restorations: A dental technique.

The trial restoration increases outcome predictability in restorative treatments, enhances communication among specialists and patients, and guides tooth preparations. It should reproduce the planned design precisely because many decisions will be made based on the transferred design. Traditionally, a diagnostic waxing design is transferred to the mouth with a flexible silicone matrix. However, a rigid matrix would ensure an accurate transfer of the planned design by avoiding the deformation of the silicone index. A step-by-step technique for fabricating a computer-aided design and computer-aided manufactured (CAD-CAM) rigid matrix relined with polyvinyl siloxane material to fabricate a trial restoration is presented. The technique ensures accurate detail reproduction and dimensional stability, avoiding deformation and ensuring a predictable transfer of the planned design.

Interarch space assessment in edentulous patients rehabilitated with complete removable dentures using open-access software.

BACKGROUND: The interarch space is defined as the vertical space between the edentulous ridge and the occlusal or incisal aspect of the opposing arch. Measuring the interarch space in a patient requiring an implant-supported fixed prosthesis is crucial for determining the prostheses to be used in each clinical situation. Depending on the measurements and other factors, such as the need for lip support or pink esthetics issues, decisions about the most convenient type of implant-supported prosthesis can be taken. Analogic workflow to measure the interarch space can represent a time-consuming and expensive procedure that may lead to inaccuracies. OBJECTIVE: To describe a step-by-step protocol to measure the upper and lower interarch space with open-access software, starting from the digital scan of the patient's complete dentures obtained with an intraoral scanner. METHODS: An extraoral scan (using an intraoral scanner) of the existing complete removable prosthesis is required to assess the interarch space for making an implant-supported prosthesis treatment planning. If the existing complete denture does not fulfill the required functional and esthetic parameters, a complete interim denture, a wax trial denture, or a printed denture prototype should be previously fabricated. The antagonist arch and the intermaxillary record scan also need to be obtained. Finally, all STL files are imported into an open-access software for measuring the interarch space. RESULTS: Open-source software can be used to measure the upper and lower interarch space from existing complete dentures following the step-by-step protocol outlined in this paper. CONCLUSION: Interarch space of edentulous patients rehabilitated with complete dentures can be measured with a 360 degrees scanning of the existing complete denture and open-access software by applying the protocol outlined in this paper. CLINICAL RELEVANCE: The clinician can assess and digitally measure the interarch space of edentulous patients requiring an implant-supported fixed prosthesis using an open access software.