Effects of Shale Pore Size and Connectivity on scCO2 Enhanced Oil Recovery: A Molecular Dynamics Simulation Investigation.

The differences in pore width distributions and connectivity of shale reservoirs have significant influences on supercritical carbon dioxide (scCO2)-enhanced oil recovery (CO2 EOR) in shale. Herein, the molecular dynamics simulation was adopted to investigate the microscopic mechanism of CO2 EOR in the shale nanopores with different pore size width distributions and pore connectivity. The results show that the pore connectivity has significant effects on the oil displacement, and the recovery efficiency is ordered as: connected pore > double pore > single pore for the 3 nm pore, which are 91.32, 74.43, and 65.93%, respectively. Therefore, the increase in pore connectivity can significantly improve the recovery efficiency of the small pore of the connected pore system. For the shale reservoirs with different pore width distributions, the oil recovery rate of large pores is generally higher than that of small pores. In addition, the displacement of oil in the small pore of the double pore system is accelerated due to the pushing effect of the discharge fluid from the large pore. The results furnish a certain theoretical support for the research of the microscopic mechanism of CO2 EOR in the shale pore with different pore width distributions and connectivity and the exploit of shale oil.

N,S coordination in Ni single-atom catalyst promoting CO2RR towards HCOOH.

Carbon-based single atom catalysts (SACs) are attracting extensive attention in the CO2 reduction reaction (CO2RR) due to their maximal atomic utilization, easily regulated active center and high catalytic activity, in which the coordination environment plays a crucial role in the intrinsic catalytic activity. Taking NiN4 as an example, this study reveals that the introduction of different numbers of S atoms into N coordination (Ni-NxS4-x (x = 1-4)) results in outstanding structural stability and catalytic activity. Owing to the additional orbitals around -1.60 eV and abundant Ni dxz, dyz, dx2, and dz2 orbital occupation after S substitution, N,S coordination can effectively facilitate the protonation of adsorbed intermediates and thus accelerate the overall CO2RR. The CO2RR mechanisms for CO and HCOOH generation via two-electron pathways are systematically elucidated on NiN4, NiN3S1 and NiN2S2. NiN2S2 yields HCOOH as the most favorable product with a limiting potential of -0.24 V, surpassing NiN4 (-1.14 V) and NiN3S1 (-0.50 V), which indicates that the different S-atom substitution of NiN4 has considerable influence on the CO2RR performance. This work highlights NiN2S2 as a high-performance CO2RR catalyst to produce HCOOH, and demonstrates that N,S coordination is an effective strategy to regulate the performance of atomically dispersed electrocatalysts.

Two-dimensional MBene: a comparable catalyst to MXene for effective CO2RR towards C1 products.

Electrochemical CO2 reduction reaction (CO2RR) to high-value-added products is one of the most promising strategies for mitigating the greenhouse effect and energy shortage. Two-dimensional (2D) MXene materials are regarded as promising catalysts for electrocatalysis, and the boron-analogs of MXenes, 2D transition metal borides (MBenes), may exhibit superior CO2RR performance owing to their unique electronic properties. Herein, a novel 2D transition metal boride, MoB, is theoretically evaluated as a potential catalyst for the CO2RR by comparing it with traditional Mo2C. MoB shows metallic nature and exhibits excellent electrical conductivity. MoB can effectively activate CO2 with a larger interaction energy of -3.64 eV than that of Mo2C. Both density of states and charge difference density reveal a significant charge transfer from MoB to CO2. MoB shows higher catalytic selectivity due to its inhibited hydrogen evolution reaction and low reaction energy for the CO2RR. At potentials more negative than -0.62 V, the CO2RR on MoB becomes a high-throughput reaction process towards CH4. This work discovered that MoB exhibited comparable CO2RR performance to Mo2C and forecasted MBenes as promising catalysts for electrocatalysis.

Interlayer Expansion in a Layered Metal-Organic Framework Enhances CO2 Capture and CO2 /N2 Separation.

Developing efficient CO2 adsorbent materials and technologies is significant to reduce the increasing greenhouse gases concentration in the atmosphere. Herein, a layered MOF with a porous kagomé lattice (kgm), which owned three phases (kgm-1, kgm-2, and kgm-3) via interlayer expansion, was evaluated as a promising CO2 capture and separation material by using grand canonical Monte Carlo simulations. Results showed that the interlayer expansion provided additional pore volume, which played a considerable role in CO2 adsorption and separation. The CO2 adsorption capacity and CO2 /N2 selectivity followed the sequence kgm-3>kgm-2>kgm-1, and kgm-3 exhibited an excellent CO2 adsorption capacity of 8.7 mmol g-1 at 1 bar with a CO2 /N2 selectivity of 130.3 at 20 bar and 298 K. Gas distribution analysis showed that CO2 and N2 are adsorbed only in the channels in kgm-1, whereas they could be adsorbed between layers in kgm-2 and kgm-3 due to the interlayer expansion. The adsorption heat and interactions between CO2 and frameworks were analyzed to elucidate the effect of interlayer expansion. Results of this work highlighted that appropriate interlayer expansion can be an effective approach for framework adsorbents to improve CO2 capture ability and separation performance at the same time.

Surface-Plasmon-Mediated Alloying for Monodisperse Au-Ag Alloy Nanoparticles in Liquid.

Plasmonic noble-metal nanoparticles with broadly tunable optical properties and catalytically active surfaces offer a unique opportunity for photochemistry. Resonant optical excitation of surface-plasmon generates high-energy hot carriers, which can participate in photochemical reactions. Although the surface-plasmon-driven catalysis on molecules has been extensively studied, surface-plasmon-mediated synthesis of bimetallic nanomaterials is less reported. Herein, we perform a detailed investigation on the formation mechanism and colloidal stability of monodisperse Au-Ag alloy nanoparticles synthesized through irradiating the intermixture of Au nanochains and AgNO3 solution with a nanosecond pulsed laser. It is revealed that the Ag atoms can be extracted from AgNO3 solution by surface-plasmon-generated hot electrons and alloy with Au atoms. Particularly, the obtained Au-Ag alloy nanoparticles without any surfactants or ligands exhibit superior stability that is confirmed by experiments as well as DLVO-based theoretical simulation. Our work would provide novel insights into the synthesis of potentially useful bimetallic nanoparticles via surface-plasmon-medicated alloying.

Molecular Dynamics Insight into the CO2 Flooding Mechanism in Wedge-Shaped Pores.

Because of the growing demand for energy, oil extraction under complicated geological conditions is increasing. Herein, oil displacement by CO2 in wedge-shaped pores was investigated by molecular dynamics simulation. The results showed that, for both single and double wedge-shaped models, pore Ⅱ (pore size from 3 to 8 nm) exhibited a better CO2 flooding ability than pore Ⅰ (pore size from 8 to 3 nm). Compared with slit-shaped pores (3 and 8 nm), the overall oil displacement efficiency followed the sequence of 8 nm > double pore Ⅱ > single pore Ⅱ > 3 nm > double pore Ⅰ > single pore Ⅰ, which confirmed that the exits of the wedge-shaped pores had determinant effects on CO2 enhanced oil recovery over their entrances. "Oil/CO2 inter-pore migration" and "siphoning" phenomena occurred in wedge-shaped double pores by comparing the volumes of oil/CO2 and the center of mass. The results of the interaction and radial distribution function analyses indicate that the wide inlet and outlet had a larger CO2−oil contact surface, better phase miscibility, higher interaction, and faster displacement. These findings clarify the CO2 flooding mechanisms in wedge-shaped pores and provide a scientific basis for the practical applications of CO2 flooding.

Can N, S Cocoordination Promote Single Atom Catalyst Performance in CO2 RR? Fe-N2 S2 Porphyrin versus Fe-N4 Porphyrin.

Single atom catalysts (SACs) are promising electrocatalysts for CO2 reduction reaction (CO2 RR), in which the coordination environment plays a crucial role in intrinsic catalytic activity. Taking the regular Fe porphyrin (Fe-N4 porphyrin) as a probe, the study reveals that the introduction of opposable S atoms into N coordination (Fe-N2 S2 porphyrin) allows for an appropriate electronic structural optimization on active sites. Owing to the additional orbitals around the Fermi level and the abundant Fe dz2 orbital occupation after S substitution, N, S cocoordination can effectively tune SACs and thus facilitating protonation of intermediates during CO2 RR. CO2 RR mechanisms lead to possible C1 products via two-, six-, and eight-electron pathways are systematically elucidated on Fe-N4 porphyrin and Fe-N2 S2 porphyrin. Fe-N4 porphyrin yields the most favorable product of HCOOH with a limiting potential of -0.70 V. Fe-N2 S2 porphyrin exhibits low limiting potentials of -0.38 and -0.40 V for HCOOH and CH3 OH, respectively, surpassing those of most Cu-based catalysts and SACs. Hence, the N, S cocoordination might provide better catalytic environment than regular N coordination for SACs in CO2 RR. This work demonstrates Fe-N2 S2 porphyrin as a high-performance CO2 RR catalyst, and highlights N, S cocoordination regulation as an effective approach to fine tune high atomically dispersed electrocatalysts.

Theoretical Investigation of the Fusion Process of Mono-Cages to Tri-Cages with CH4/C2H6 Guest Molecules in sI Hydrates.

Owing to a stable and porous cage structure, natural gas hydrates can store abundant methane and serve as a potentially natural gas resource. However, the microscopic mechanism of how hydrate crystalline grows has not been fully explored, especially for the structure containing different guest molecules. Hence, we adopt density functional theory (DFT) to investigate the fusion process of structure I hydrates with CH4/C2H6 guest molecules from mono-cages to triple-cages. We find that the volume of guest molecules affects the stabilities of large (51262, L) and small (512, s) cages, which are prone to capture C2H6 and CH4, respectively. Mixed double cages (small cage and large cage) with the mixed guest molecules have the highest stability and fusion energy. The triangular triple cages exhibit superior stability because of the three shared faces, and the triangular mixed triple cages (large-small-large) structure with the mixed guest molecules shows the highest stability and fusion energy in the triple-cage fusion process. These results can provide theoretical insights into the growth mechanism of hydrates with other mono/mixed guest molecules for further development and application of these substances.

Theoretical analysis of the absorption spectrum, electronic structure, excitation, and intramolecular electron transfer of D-A'-π-A porphyrin dyes for dye-sensitized solar cells.

A series of porphyrin dyes with D-A'-π-A structure were designed and theoretically investigated by DFT and TD-DFT methods. Different electron-withdrawing auxiliary acceptor units were introduced into the dye molecule skeleton to shed light on how the type and position of auxiliary acceptors influence the photoelectric performance of the dyes. It was found that the introduction of electron-withdrawing units, BTD, TPZ, BTZ, PP and DPPZ, between the Zn-porphyrin core and the anchoring group had a significantly positive influence on the performance of the dye molecules. Also, more appropriate electron distribution in the molecular orbital and the lower HOMO-LUMO energy gap, more extensive absorption coverage, higher light-harvesting efficiency, lower orbital overlap, and more effective long-range intramolecular electron transfer (IET) process can be achieved as compared to the reference dye. Among these five electron-withdrawing units, BTD and TPZ had the effect leading to the greatest improvement and therefore, are the best candidates for auxiliary acceptors. The calculated results indicated that the longitudinal π-conjugation of the electron-withdrawing unit also had an obvious effect on the performance of the dye molecule, and NTD is expected to be a more effective auxiliary acceptor than BTD. The effects of the relative positions of the auxiliary acceptors in the dye molecular skeleton were also investigated. A comparative study of AX1-3 and AA1-3 showed that the introduction of BTD, TPZ and BTZ units between the donor part and the Zn-porphyrin core may have a negative impact on the performance of the dyes. Our studies are expected to provide new insight for the design and screening of high-efficiency porphyrin dyes for DSSCs applications.

Theoretical Analysis on Heteroleptic Cu(I)-Based Complexes for Dye-Sensitized Solar Cells: Effect of Anchors on Electronic Structure, Spectrum, Excitation, and Intramolecular and Interfacial Electron Transfer.

Two groups of heteroleptic Cu(I)-based dyes were designed and theoretically investigated by density functional theory (DFT) and time-dependent DFT (TD-DFT) methods. Different anchors were integrated into the dye skeleton to shed light on how the type of anchor influenced the electronic structure, absorption spectrum, electron excitation, and intramolecular and interfacial electron transfer of dyes. The results indicated that, compared with other dyes, the dyes with cyanoacrylic acid and nitric acid exhibited more appropriate electron distributions in frontier molecular orbitals (FMOs), lower HOMO (the highest occupied molecular orbital) -LUMO (the lowest unoccupied molecular orbital) energy gaps, broader absorption spectral ranges as well as improved spectral characteristics in the near-infrared region and better intramolecular electron transfer (IET) characteristics with more electrons transferred to longer distances, but smaller orbital overlap. Among all the studied Cu(I)-based dyes, B1 and P1 (with cyanoacrylic acid anchoring group) exhibited the best interface electronic structure parameters with a relatively short electron injection time (τinj) and large dipole moment (µnormal), which would have a positive effect on the open-circuit photovoltage (Voc) and short-circuit current density (Jsc), resulting in high power conversion efficiency (PCE) of dye-sensitized solar cells (DSSCs). Our findings are expected to provide a new insight into the designing and screening of high-performance dyes for DSSCs.

Synthesis of 8-Substituted 2'-Deoxyisoguanosines via Unprotected 8-Brominated 2-Amino-2'-deoxyadenosine.

A variety of applications of 8-alkynylated nucleosides has prompted the synthesis of new purine analogues. Bromination of unprotected 2-amino-2'-deoxyadenosine with Br2 /AcOH/AcONa gives 2-amino-8-bromo-2'-deoxyadenosine (87%). The brominated derivative is converted to 8-alkynylated 2-amino-2'-deoxyadenosines by palladium-catalyzed Sonogashira cross-coupling reaction via microwave assistance (81 - 95%). The resulting compounds are further transformed to 8-alkynylated 2'-deoxyisoguanosines (52 - 70%). The physical properties of new compounds are investigated.

The adsorption behaviour of CH4 on microporous carbons: effects of surface heterogeneity.

The effects of chemical and structural surface heterogeneity on the CH4 adsorption behaviour on microporous carbons have been investigated using a hybrid theoretical approach, including the use of density functional theory (DFT), molecular dynamics (MD), and grand canonical Monte Carlo (GCMC) simulations. Bader charge analysis is first performed to analyze the surface atomic partial charges. The CH4 adsorption densities in defective and functionalized graphite slit pores are lower than that in the perfect pore according to the MD simulations. Finally, the CH4 adsorption isotherms for the perfect, defective and functionalized slit pores are analyzed using the GCMC simulations in combination with the DFT and MD results. For pores with a defective surface, the adsorption capacities decrease; the embedded functional groups decrease the adsorption capacity at low pressure and enhance it at high pressure. Our results demonstrate the significant effects of chemical and structural surface heterogeneity on the CH4 adsorption and provide a systematic approach to understand the gas adsorption behaviour.

Advancements in removing common antibiotics from wastewater using nano zero valent iron.

The pollutants such as heavy metals, organic matter, and nitrates in soil and water pose challenges to environmental remediation technology. Nano zero valent iron has shown enormous potential in the field of environmental remediation due to its excellent adsorption performance. By using carbon based materials, rock minerals, biomolecules, etc., as supporting materials for nZVI, and through structural and performance modifications, its performance has been successfully optimized, reducing defects such as aggregation and easy oxidation of the material. This article compares and summarizes the modification effects of different loadings on nZVI, and comprehensively reviews the latest progress, preparation methods, and application of nZVI particles in soil and water remediation. Specifically, this article explores in detail the impact and mechanism of nZVI particles in commonly used antibiotics contaminated environments. Firstly, the combination methods of different types of materials with zero valent iron, as well as the synthesis methods and application scenarios of nZVI, were integrated. Secondly, the interaction mechanism between pollutants and nZVI was introduced in detail, including adsorption, redox reactions, and co-precipitation. Subsequently, environmental factors that affect repair efficiency were emphasized, such as pH value, coexisting components, oxygen, contact time, and temperature. Finally, the challenges faced by the application of nZVI in actual polluted soil and water bodies, as well as the prospects for its long-term efficacy and safety evaluation, are proposed to promote further development in the future.

[Progress in enrichment methods for protein N-phosphorylation].

Protein phosphorylation is one of the most common and important post-translational modifications that regulates almost all life processes. In particular, protein phosphorylation regulates the development of major diseases such as tumors, neurodegenerative diseases, and diabetes. For example, excessive phosphorylation of Tau protein can cause neurofibrillary tangles, leading to Alzheimer's disease. Therefore, large-scale methods for identifying protein phosphorylation must be developed. Rapid developmentin efficient enrichment methods and biological mass spectrometry technologies have enabled the large-scale identification of low-abundance protein O-phosphorylation modifications in, allowing for a more thorough study of their biological functions. The N-phosphorylation modifications that occur on the side-chain amino groups of histidine, arginine, and lysine have recently received increased attention. For example, the biological function of histidine phosphorylation in prokaryotes has been well studied; this type of modification regulates signal transduction and sugar metabolism. Two mammalian pHis kinases (NME1 and NME2) and three pHis phosphatases (PHPT1, LHPP, and PGAM5) have been successfully identified using various biological methods. N-Phosphorylation is involved in multiple biological processes, and its functions cannot be ignored. However, N-phosphorylation is unstable under acidic and thermal conditions owing to the poor chemical stability of the P-N bond. Unfortunately, the current O-phosphorylation enrichment method, which relies on acidic conditions, is unsuitable for N-phosphorylation enrichment, resulting in a serious lag in the large-scale identification of protein N-phosphorylation. The lack of enrichment methods has also seriously hindered studies on the biological functions of N-phosphorylation. Therefore, the development of efficient enrichment methods that target protein N-phosphorylation is an urgent undertaking. Research on N-phosphorylation proteome enrichment methods is limited, hindering functional research. Thus, summarizing such methods is necessary to promote further functional research. This article introduces the structural characteristics and reported biological functions of protein N-phosphorylation, reviews the protein N-phosphorylation modification enrichment methods developed over the past two decades, and analyzes the advantages and disadvantages of each method. In this study, both antibody-based and nonantibody-dependent methods are described in detail. Owing to the stability of the molecular structure of histidine, the antibody method is currently limited to histidine phosphorylation enrichment research. Future studies will focus on the development of new enrichment ligands. Moreover, research on ligands will promote studies on other nonconventional phosphorylation targets, such as two acyl-phosphates (pAsp, pGlu) and S-phosphate (pCys). In summary, this review provides a detailed analysis of the history and development directions of N-phosphorylation enrichment methods.

Insight into the Critical Role of Oxygen Vacancies and V=O Bonds Length in V2O5 for Advanced Zinc Ion Storage.

Due to the larger sizes and stronger positive polarity of Zn2+ than dominant univalent ions, Zn2+ sluggish diffusion within V2O5 host electrodes is an essential issue in developing aqueous zinc-ion batteries (ZIBs) of higher energy densities. Herein, a high-performance V2O5 cathode was developed through subtly synthesizing and tuning V2O5 with oxygen vacancies-enriched and elongated apical V=O1 bond by altering the gradient concentration of hydrazine hydrate in the gas-solid reaction system. This strategy can enhance both intrinsic and extrinsic conductivity to a large extent. The electrochemical testing demonstrated the oxygen vacancies-enriched and elongated apical V=O1 bond can not only increase the intrinsic electronic conductivity of V2O5, but also induce additional pseudocapacitance to enhance the Zn2+ diffusion kinetics. We used infrared spectroscopy and Raman spectroscopy to characterize the change in the bond length structure of V2O5. Simultaneously, the long-term cyclability (capacity retention of 76.9 % after 1200 cycles at 4.0 A g-1) and rate capabilities (218 mAh g-1 at 4.0 A g-1) are promoted as well. We believe that our work might shed light on the bond length engineering of V2O5 and provide insights for the reasonable designing of novel cathodes for practical rechargeable ZIBs.

Removal mechanism of Pb(ii) from soil by biochar-supported nanoscale zero-valent iron composite materials.

As an adsorbent, biochar has a highly porous structure and strong adsorption capacity, and can effectively purify the environment. In response to the increasingly serious problem of heavy metal pollution in water, this study used nano zero valent iron and rice husk biochar to prepare a new type of magnetic sheet-like biochar loaded nano zero valent iron (BC-nZVI) composite material through rheological phase reaction, showing remarkable advantages such as low cost, easy preparation, and superior environmental remediation effect. The physical and chemical properties and structure of the material were extensively characterized using various methods such as HRTEM, XPS, FESEM, EDS, XRD, FTIR, and RAMAN. Concurrently, batch experiments were undertaken to assess the removal efficiency of Pb(ii) by BC-nZVI, with investigations into the influence of pH value, temperature, soil water ratio, and initial concentration of heavy metal ion solution on its removal efficiency. The results indicate that the removal of Pb(ii) by BC-nZVI reaches an equilibrium state after around 120 minutes. Under the conditions of pH 6, temperature 20 °C, soil water ratio 1 : 5, and BC-nZVI dosage of 1 g L-1, BC-nZVI can reduce the Pb(ii) content in wastewater with an initial concentration of 30 mg L-1 to trace levels, and the treatment time is about 120 minutes. The analysis of adsorption kinetics and isotherms indicates that the adsorption process of Pb(ii) by BC-nZVI adheres to the quasi-second-order kinetic model and Langmuir model, suggesting a chemical adsorption process. Thermodynamic findings reveal that the adsorption of Pb(ii) by BC-nZVI is spontaneous. Furthermore, BC-nZVI primarily accumulates Pb(ii) through adsorption co-precipitation. BC-nZVI serves as an eco-friendly, cost-effective, and highly efficient adsorbent, showing promising capabilities in mitigating Pb(ii) heavy metal pollution. Its recoverability and reusability facilitated by an external magnetic field make it advantageous for remediating and treating lead-contaminated sites.

Efficient CO2 Capture and Separation in MOFs: Effect from Isoreticular Double Interpenetration.

Severe CO2 emissions has posed an increasingly alarming threat, motivating the development of efficient CO2 capture materials, one of the key parts of carbon capture, utilization, and storage (CCUS). In this study, a series of metal-organic frameworks (MOFs) named Sc-X (X = S, M, L) were constructed inspired by recorded MOFs, Zn-BPZ-SA and MFU-4l-Li. The corresponding isoreticular double-interpenetrating MOFs (Sc-X-IDI) were subsequently constructed via the introduction of isoreticular double interpenetration. Grand canonical Monte Carlo (GCMC) simulations were adopted at 298 K and 0.1-1.0 bar to comprehensively evaluate the CO2 capture and separation performances in Sc-X and Sc-X-IDI, with gas distribution, isothermal adsorption heat (Qst), and van der Waals (vdW)/Coulomb interactions. It is showed that isoreticular double interpenetration significantly improved the interactions between adsorbed gases and frameworks by precisely modulating pore sizes, particularly observed in Sc-M and Sc-M-IDI. Specifically, the Qst and Coulomb interactions exhibited a substantial increase, rising from 28.38 and 22.19 kJ mol-1 in Sc-M to 43.52 and 38.04 kJ mol-1 in Sc-M-IDI, respectively, at 298 K and 1.0 bar. Besides, the selectivity of CO2 over CH4/N2 was enhanced from 55.36/107.28 in Sc-M to 3308.61/7021.48 in Sc-M-IDI. However, the CO2 capture capacity is significantly influenced by the pore size. Sc-M, with a favorable pore size, exhibits the highest capture capacity of 15.86 mmol g-1 at 298 K and 1.0 bar. This study elucidated the impact of isoreticular double interpenetration on the CO2 capture performance in MOFs.

Release of ions enhanced the antibacterial performance of laser-generated, uncoated Ag nanoparticles.

Identifying the antibacterial mechanisms of elemental silver at the nanoscale remains a significant challenge due to the intertwining behaviors between the particles and their released ions. The open question is which of the above factor dominate the antibacterial behaviors when silver nanoparticles (Ag NPs) with different sizes. Considering the high reactivity of Ag NPs, prior research has primarily concentrated on coated particles, which inevitably hinder the release of Ag+ ions due to additional chemical agents. In this study, we synthesized various Ag NPs, both coated and uncoated, using the laser ablation in liquids (LAL) technique. By analyzing both the changes in particle size and Ag+ ions release, the impacts of various Ag NPs on the cellular activity and morphological changes of gram-negative (E. coil) and gram-positive (S. aureus) bacteria were evaluated. Our findings revealed that for uncoated Ag NPs, smaller particles exhibited greater ions release efficiency and enhanced antibacterial efficacy. Specifically, particles approximately 1.5 nm in size released up to 55 % of their Ag+ ions within 4 h, significantly inhibiting bacterial growth. Additionally, larger particles tended to aggregate on the bacterial cell membrane surface, whereas smaller particles were more likely to be internalized by the bacteria. Notably, treatment with smaller Ag NPs led to more pronounced bacterial morphological changes and elevated levels of intracellular reactive oxygen species (ROS). We proposed that the bactericidal activity of Ag NPs stems from the synergistic effect between particle-cell interaction and the ionic silver, which is dependent on the crucial parameter of particle size.

In-situ construction of iron-modified nickel nanoparticles assisted by hexamethylenetetramine with the internal and external collaboration for highly selective electrocatalytic carbon dioxide reduction.

Carbon dioxide (CO2) electroreduction provides a sustainable route for realizing carbon neutrality and energy supply. Up to now, challenges remain in employing abundant and inexpensive nickel materials as candidates for CO2 reduction due to their low activity and favorable hydrogen evolution. Here, the representative iron-modified nickel nanoparticles embedded in nitrogen-doped carbon (Ni1-Fe0.125-NC) with the porous botryoid morphology were successfully developed. Hexamethylenetetramine is used as nitrogen-doped carbon source. The collaboration of internal lattice expansion with electron effect and external confinement effect with size effect endows the significant enhancement in electrocatalytic CO2 reduction. The optimized Ni1-Fe0.125-NC exhibits broad potential ranges for continuous carbon monoxide (CO) production. A superb CO Faradaic efficiency (FECO) of 85.0 % realized at -1.1 V maintains a longtime durability over 35 h, which exceeds many state-of-the-art metal catalysts. Theoretical calculations further confirm that electron redistribution promotes the desorption of CO in the process for favorable CO production. This work opens a new avenue to design efficient nickel-based materials by considering the intrinsic structure and external confinement for CO2 reduction.

Mechanistic insight into the hydrazine decomposition on Rh(111): effect of reaction intermediate on catalytic activity.

Periodic density functional theory (DFT) calculations have been performed to systematically investigate the effect of reaction intermediate on catalytic activity for hydrazine (N2H4) decomposition on Rh(111). Reaction mechanisms via intramolecular and NH2-assisted N2H4 decompositions are comparatively analyzed, including adsorption configuration, reaction energy and barrier of elementary step, and reaction network. Our results show that the most favorable N2H4 decomposition pathway starts with the initial N-N bond scission to the NH2 intermediate, followed by stepwise H stripping from adsorbed N2Hx (x = 1-4) species, and finally forms the N2 and NH3 products. Comparatively, the stepwise intramolecular dehydrogenation via N2H4→ N2H3→ N2H2→ N2H → N2, and N2H4→ NH2→ NH → N with or without NH2 promotion effect, are unfavorable due to higher energy barriers encountered. Energy barrier analysis, reaction rate constants, and electronic structures are used to identify the crucial competitive route. The promotion effect of the NH2 intermediate is structurally reflected in the weakening of the N-H bond and strengthening of the N-N bond in N2Hx in the coadsorption system; it results intrinsically from the less structural deformation of the adsorbate, and weakening of the interaction between dehydrogenated fragment and departing H in transition state. Our results highlight the crucial effect of reaction intermediate on catalytic activity and provide a theoretical approach to analyze the effect.