Revealing the impact of thermal annealing on the perovskite/organic bulk heterojunction interface in photovoltaic devices.

Perovskite/organic bulk heterojunction (BHJ) integrated solar cells have tremendous development potential to exceed the Shockley-Queisser limit efficiency of single-junction photovoltaics, due to the merits of spectra response extension. However, the presence of energy level barriers and severe non-radiative recombination at the interface between perovskite and BHJ greatly hindered the transport and collection of charge carriers, usually leading to large Voc and photocurrent loss, as well as the stability degradation of integrated devices. Therefore, investigating the interface properties of perovskite/BHJ is crucial for understanding the charge transport process and enhancing device performance. In this study, we effectively regulated the interface properties and charge transport in perovskite/BHJ integrated devices using a thermal annealing process. Using Kelvin probe microscopy, photoluminescence, and transient absorption spectroscopy, we revealed that moderate annealing treatment would contribute to forming close interface contact and provide more channels or pathways for charge transfer, which is advantageous for the interface charge collection and device performance. In addition, the lone pair electrons of acyl, thiophene and pyrrole function groups in polymer PDPP3T and PCBM can act as the Lewis base and provide electrons to the under-coordinated lead atoms or clusters in the perovskite, effectively passivating traps on the surface and grain boundaries of the perovskite through Lewis acid-base coordination. Finally, we improved the photovoltaic conversion efficiency of the device to 21.57% with enhanced stability using an optimized thermal annealing process. This study provides a comprehensive understanding of the integrated perovskite/BHJ interface properties, which could be extended to other optoelectronic devices based on a similar integrated structure.

Reversible Stacking of 2D ZnIn2 S4 Atomic Layers for Enhanced Photocatalytic Hydrogen Evolution.

It is technically challenging to reversibly tune the layer number of 2D materials in the solution. Herein, a facile concentration modulation strategy is demonstrated to reversibly tailor the aggregation state of 2D ZnIn2 S4 (ZIS) atomic layers, and they are implemented for effective photocatalytic hydrogen (H2 ) evolution. By adjusting the colloidal concentration of ZIS (ZIS-X, X = 0.09, 0.25, or 3.0 mg mL-1 ), ZIS atomic layers exhibit the significant aggregation of (006) facet stacking in the solution, leading to the bandgap shift from 3.21 to 2.66 eV. The colloidal stacked layers are further assembled into hollow microsphere after freeze-drying the solution into solid powders, which can be redispersed into colloidal solution with reversibility. The photocatalytic hydrogen evolution of ZIS-X colloids is evaluated, and the slightly aggregated ZIS-0.25 displays the enhanced photocatalytic H2 evolution rates (1.11 µmol m-2 h-1 ). The charge-transfer/recombination dynamics are characterized by time-resolved photoluminescence (TRPL) spectroscopy, and ZIS-0.25 displays the longest lifetime (5.55 µs), consistent with the best photocatalytic performance. This work provides a facile, consecutive, and reversible strategy for regulating the photo-electrochemical properties of 2D ZIS, which is beneficial for efficient solar energy conversion.

Highly Sensitive and Ultra-Broadband VO2(B) Photodetector Dominated by Bolometric Effect.

In this study, Wadsley B phase vanadium oxide (VO2(B)) with broad-band photoabsorption ability, a large temperature coefficient of resistance (TCR), and low noise was developed for uncooled broad-band detection. By using a freestanding structure and reducing the size of active area, the VO2(B) photodetector shows stable and excellent performances in the visible to the terahertz region (405 nm to 0.88 mm), with a peak TCR of -4.77% K-1 at 40 °C, a peak specific detectivity of 6.02 × 109 Jones, and a photoresponse time of 83 ms. A terahertz imaging ability with 30 × 30 pixels was demonstrated. Scanning photocurrent imaging and real-time temperature-photocurrent measurements confirm that a photothermal-type bolometric effect is the dominating mechanism. The study shows the potential of VO2(B) in applications as a new type of uncooled broad-band photodetection material and the potential to further raise the performance of broad-band photodetectors by structural design.

Reciprocally Photovoltaic Light-Emitting Diode Based on Dispersive Perovskite Nanocrystal.

Integrating highly efficient photovoltaic (PV) function into light-emitting diodes (LEDs) for multifunctional display is of great significance for compact low-power electronics, but it remains challenging. Herein, it is demonstrated that solution engineered perovskite nanocrystals (PNCs, ≈100 nm) enable efficient electroluminescence (EL) and PV performance within a single device through tailoring the dispersity and interface. It delivers the maximum brightness of 490 W sr-1  m-2 at 2.7 V and 23.2% EL external quantum efficiency, a record value for near-infrared perovskite LED, as well as 15.23% PV efficiency, among the highest value for nanocrystal perovskite solar cells. The PV-EL performance is well in line with the reciprocity relation. These all-solution-processed PV-LED devices open up viable routes to a variety of advanced applications, from touchless interactive screens to energy harvesting displays and data communication.

Polycrystalline Few-Layer Graphene as a Durable Anticorrosion Film for Copper.

Corrosion of metals in atmospheric environments is a worldwide problem in industry and daily life. Traditional anticorrosion methods including sacrificial anodes or protective coatings have performance limitations. Here, we report atomically thin, polycrystalline few-layer graphene (FLG) grown by chemical vapor deposition as a long-term protective coating film for copper (Cu). A six-year old, FLG-protected Cu is visually shiny and detailed material characterizations capture no sign of oxidation. The success of the durable anticorrosion film depends on the misalignment of grain boundaries between adjacent graphene layers. Theoretical calculations further found that corrosive molecules always encounter extremely high energy barrier when diffusing through the FLG layers. Therefore, the FLG is able to prevent the corrosive molecules from reaching the underlying Cu surface. This work highlights the interesting structures of polycrystalline FLG and sheds insight into the atomically thin coatings for various applications.

Defect Etching of Phase-Transition-Assisted CVD-Grown 2H-MoTe2.

2D molybdenum ditelluride (MoTe2 ) with polymorphism is a promising candidate to developing phase-change memory, high-performance transistors and spintronic devices. The phase-transition-assisted chemical vapor deposition (CVD) process has been used to prepare large-scale 2H-MoTe2 with large grain size and low density of grain boundary. However, because of the lack of precise control of the growth condition, some defects including the amorphous regions and grain boundaries in 2H-MoTe2 are hardly avoidable. Here, a facile method of selectively etching defects in large-scale CVD-grown 2H-MoTe2 by triiodide ion (I3 - ) solution is reported. The defect etching is attributed to the reduced lattice symmetry, high chemisorption activity and high conductivity of the defects due to the high density of Te vacancies. The treated 2H-MoTe2 shows the suppressed hysteresis in the electrical transfer curve, enhances hole mobility and the higher effective barrier height on the metal contact, suggesting the decreased density of defects. Further chemical analysis indicates that the 2H-MoTe2 is not damaged or doped by I3 - solution during the etching process. This simple and low-cost post-processing method is effective for etching the defects in large-area 2H-MoTe2 for high-performance device applications.

Molecule occupancy by a n-butylamine treatment to facilitate the conversion of PbI2 to perovskite in sequential deposition.

Herein, we propose a new approach of molecule occupancy via a vapor treatment to facilitate the conversion of PbI2 to perovskite in sequential deposition. We have shown that the morphology of PbI2 and the subsequent crystallization of perovskite can be effectively tuned, thus leading to the elimination of residual PbI2 and promotion of perovskite growth.

A Robust Solid Electrolyte Interphase Layer Augments the Ion Storage Capacity of Bimetallic-Sulfide-Containing Potassium-Ion Batteries.

Metal-organic framework-derived NiCo2.5 S4 microrods wrapped in reduced graphene oxide (NCS@RGO) were synthesized for potassium-ion storage. Upon coordination with organic potassium salts, NCS@RGO exhibits an ultrahigh initial reversible specific capacity (602 mAh g-1 at 50 mA g-1 ) and ultralong cycle life (a reversible specific capacity of 495 mAh g-1 at 200 mA g-1 after 1 900 cycles over 314 days). Furthermore, the battery demonstrates a high initial Coulombic efficiency of 78 %, outperforming most sulfides reported previously. Advanced ex situ characterization techniques, including atomic force microscopy, were used for evaluation and the results indicate that the organic potassium salt-containing electrolyte helps to form thin and robust solid electrolyte interphase layers, which reduce the formation of byproducts during the potassiation-depotassiation process and enhance the mechanical stability of electrodes. The excellent conductivity of the RGO in the composites, and the robust interface between the electrodes and electrolytes, imbue the electrode with useful properties; including, ultrafast potassium-ion storage with a reversible specific capacity of 402 mAh g-1 even at 2 A g-1 .

1T' Transition Metal Telluride Atomic Layers for Plasmon-Free SERS at Femtomolar Levels.

Plasmon-free surface enhanced Raman scattering (SERS) based on the chemical mechanism (CM) is drawing great attention due to its capability for controllable molecular detection. However, in comparison to the conventional noble-metal-based SERS technique driven by plasmonic electromagnetic mechanism (EM), the low sensitivity in the CM-based SERS is the dominant barrier toward its practical applications. Herein, we demonstrate the 1T' transition metal telluride atomic layers (WTe2 and MoTe2) as ultrasensitive platforms for CM-based SERS. The SERS sensitivities of analyte dyes on 1T'-W(Mo)Te2 reach EM-comparable ones and become even greater when it is integrated with a Bragg reflector. In addition, the dye fluorescence signals are efficiently quenched, making the SERS spectra more distinguishable. As a proof of concept, the SERS signals of analyte Rhodamine 6G (R6G) are detectable even with an ultralow concentration of 40 (400) fM on pristine 1T'-W(Mo)Te2, and the corresponding Raman enhancement factor (EF) reaches 1.8 × 109 (1.6 × 108). The limit concentration of detection and the EF of R6G can be further enhanced into 4 (40) fM and 4.4 × 1010 (6.2 × 109), respectively, when 1T'-W(Mo)Te2 is integrated on the Bragg reflector. The strong interaction between the analyte and 1T'-W(Mo)Te2 and the abundant density of states near the Fermi level of the semimetal 1T'-W(Mo)Te2 in combination gives rise to the promising SERS effects by promoting the charge transfer resonance in the analyte-telluride complex.

A simple way to synthesize large-scale Cu2O/Ag nanoflowers for ultrasensitive surface-enhanced Raman scattering detection.

Here, we report a simple strategy to prepare highly sensitive surface-enhanced Raman spectroscopy (SERS) substrates based on Ag decorated Cu2O nanoparticles by combining two common techniques, viz, thermal oxidation growth of Cu2O nanoparticles and magnetron sputtering fabrication of a Ag nanoparticle film. Methylene blue is used as the Raman analyte for the SERS study, and the substrates fabricated under optimized conditions have very good sensitivity (analytical enhancement factor ∼108), stability, and reproducibility. A linear dependence of the SERS intensities with the concentration was obtained with an R 2 value >0.9. These excellent properties indicate that the substrate has great potential in the detection of biological and chemical substances.

Quantitative Analysis of Scattering Mechanisms in Highly Crystalline CVD MoS2 through a Self-Limited Growth Strategy by Interface Engineering.

The electrical performance of highly crystalline monolayer MoS2 is remarkably enhanced by a self-limited growth strategy on octadecyltrimethoxysilane self-assembled monolayer modified SiO2 /Si substrates. The scattering mechanisms in low-κ dielectric, including the dominant charged impurities, acoustic deformation potentials, optical deformation potentials), Fröhlich interaction, and the remote interface phonon interaction in dielectrics, are quantitatively analyzed.

Surface roughness induced cracks of the deposition film from drying colloidal suspension.

We investigate crack formation in deposition films from drying colloidal suspension drops, by varying the roughness and texture of the substrate. The experimental results indicate that the crack number or crack spacing presents a general dependence on the substrate roughness, despite the orientation of the substrate textures. Interestingly, the crack spacing decreases with the increase of the roughness. Two possible mechanisms are proposed to understand the dependence of the cracks on roughness. Firstly, the concentration reduction of the drying suspension due to collecting colloidal particles from the substrate textures decreases the crack spacing. Secondly, stress concentration resulting from the defects (the notches in textures) in the dried deposition enhances crack formation. However, a quantitative estimation by the calculation of the stress concentrating factors reveals that the notch of the substrate textures dominates crack variation. The results here bring forth a practical method for controlling the crack orientation and suppression, and a potential application to crack-free coatings, films and paintings during the drying of complex fluids.

Interaction at the silicon/transition metal oxide heterojunction interface and its effect on the photovoltaic performance.

The interfacial reaction and energy level alignment at the Si/transition metal oxide (TMO, including MoO3-x, V2O5-x, WO3-x) heterojunction are systematically investigated. We confirm that the interfacial reaction appears during the thermal deposition of TMO, with the reaction extent increasing from MoO3-x, to V2O5-x, and to WO3-x. The reaction causes the surface oxidation of silicon for faster electron/hole recombination, and the reduction of TMO for effective hole collection. The photovoltaic performance of the Si/TMO heterojunction devices is affected by the interface reaction. MoO3-x are the best hole selecting materials that induce least surface oxidation but strongest reduction. Compared with H-passivation, methyl group passivation is an effective way to reduce the interface reaction and improve the interfacial energy level alignment for better electron and hole collection.

Impact of health education on promoting influenza vaccination health literacy in primary school students: a cluster randomised controlled trial protocol.

INTRODUCTION: Influenza is a major public health threat, and vaccination is the most effective prevention method. However, vaccination coverage remains suboptimal. Low health literacy regarding influenza vaccination may contribute to vaccine hesitancy. This study aims to evaluate the effect of health education interventions on influenza vaccination rates and health literacy. METHODS AND ANALYSIS: This cluster randomised controlled trial will enrol 3036 students in grades 4-5 from 20 primary schools in Dongguan City, China. Schools will be randomised to an intervention group receiving influenza vaccination health education or a control group receiving routine health education. The primary outcome is the influenza vaccination rate. Secondary outcomes include health literacy levels, influenza diagnosis rate, influenza-like illness incidence and vaccine protection rate. Data will be collected through questionnaires, influenza surveillance and self-reports at baseline and study conclusion. ETHICS AND DISSEMINATION: Ethical approval has been sought from the Ethics Committee of the School of Public Health, Sun Yat-sen University. Findings from the study will be made accessible to both peer-reviewed journals and key stakeholders. TRIAL REGISTRATION NUMBER: NCT06048406.

Highly Sensitive Perovskite Photoplethysmography Sensor for Blood Glucose Sensing Using Machine Learning Techniques.

Accurate non-invasive monitoring of blood glucose (BG) is a challenging issue in the therapy of diabetes. Here near-infrared (NIR) photoplethysmography (PPG) sensor based on a vapor-deposited mixed tin-lead hybrid perovskite photodetector is developed. The device shows a high detectivity of 5.32 × 1012 Jones and a large linear dynamic range (LDR) of 204 dB under NIR light, guaranteeing accurate extraction of eleven features from the PPG signal. By a combination of machine learning, accurate prediction of blood glucose level with mean absolute relative difference (MARD) as small as 2.48% is realized. The self-powered PPG sensor also works for real-time outdoor healthcare monitors using sunlight as a light source. The potential for early diabetes diagnoses by the perovskite PPG sensor is demonstrated.

Gradient Thermal Annealing Assisted Perovskite Film Crystallization Regulation for Efficient and Stable Photovoltaic-Photodetection Bifunctional Device.

Perovskite crystallization regulation is essential to obtain excellent film optoelectronic properties and device performances. However, rapid crystallization during annealing always results in poor perovskite film and easy formation of trap, thereby greatly restricting device performance due to severe non-radiative recombination. Here, an easy and reproducible gradient thermal annealing (GTA) approach is used to regulate the perovskite crystallization. Through a low-temperature initial annealing of GTA, the solvent evaporation is slowed down, thus extending nucleation time and providing a buffer for the rapid crystallization of perovskite grains in the subsequent high-temperature stage. As a result, completely converted and highly crystalline perovskite is obtained with 1.6 times larger grain size, reduced trap density and suppressed non-radiative recombination of photo-generated carriers. The film crystallinity is also enhanced with more advantageous (100) and (111) lattice facets which are favorable for carrier transport. Consequently, the perovskite photodetectors exhibit a large linear dynamic range of 174 dB and an excellent response even under ultra-weak light of 303 pW. Meanwhile, perovskite solar cells achieved increased PCE and maintained 85% of original efficiency after heating at 65 °C for nearly 1000 h under unencapsulated conditions. To the knowledge, this represents the best performance reported for a perovskite photovoltaic-photodetection bifunctional device.

Surface Planarization-Epitaxial Growth Enables Uniform 2D/3D Heterojunctions for Efficient and Stable Perovskite Solar Modules.

Two-dimensional/three-dimensional (2D/3D) halide perovskite heterojunctions are widely used to improve the efficiency and stability of perovskite solar cells. However, interfacial defects between the 2D and 3D perovskites and the poor coverage of the 2D capping layer still hinder long-term stability and homogeneous charge extraction. Herein, a surface planarization strategy on 3D perovskite is developed that enables an epitaxial growth of uniform 2D/3D perovskite heterojunction via a vapor-assisted process. The homogeneous charge extraction and suppression of interfacial nonradiative recombination is achieved by forming a uniform 2D/3D interface. As a result, a stabilized power output efficiency of 25.97% is achieved by using a 3D perovskite composition with a bandgap of 1.55 eV. To demonstrate the universality of the strategy applied for different perovskites, the champion device based on a 1.57 eV bandgap 3D perovskite results in an efficiency of 25.31% with a record fill factor of 87.6%. Additionally, perovskite solar modules achieve a designated area (24.04 cm2) certified efficiency of 20.75% with a high fill factor of 80.0%. Importantly, the encapsulated uniform 2D/3D modules retain 96.9% of the initial efficiency after 1246 h operational tracking under 65 °C (ISOS-L-3 protocol) and 91.1% after 862 h under the ISOS-O-1 protocol.

Fast, Multi-Bit, and Vis-Infrared Broadband Nonvolatile Optoelectronic Memory with MoS2 /2D-Perovskite Van der Waals Heterojunction.

Nonvolatile optoelectronic memory (NVOM) integrating the functions of optical sensing and long-term memory can efficiently process and store a large amount of visual scene information, which has become the core requirement of multiple intelligence scenarios. However, realizing NVOM with vis-infrared broadband response is still challenging. Herein, the room temperature vis-infrared broadband NVOM based on few-layer MoS2 /2D Ruddlesden-Popper perovskite (2D-RPP) van der Waals heterojunction is realized. It is found that the 2D-RPP converts the initial n-type MoS2 into p-type and facilitates hole transfer between them. Furthermore, the 2D-RPP rich in interband states serves as an effective electron trapping layer as well as broadband photoresponsive layer. As a result, the dielectric-free MoS2 /2D-RPP heterojunction enables the charge to transfer quickly under external field, which enables a large memory window (104 V), fast write speed of 20 µs, and optical programmable characteristics from visible light (405 nm) to telecommunication wavelengths (i.e., 1550 nm) at room temperature. Trapezoidal optical programming can produce up to 100 recognizable states (>6 bits), with operating energy as low as 5.1 pJ per optical program. These results provide a route to realize fast, low power, multi-bit optoelectronic memory from visible to the infrared wavelength.

Static and Dynamic Demonstration of the Ecological Level of Ethnic Cultural Industries Based on the Internet of Things and Environmental Responsibility.

The cultural industry of ethnic minorities carries the wisdom of many ancients. In today's modernization, ethnic minority cultural industry products can still impress people's hearts with exquisite handicrafts, natural materials, and strong culture. The rise in demand for ethnic cultural products will bring about an increase in the demand for raw materials for handmade products, which is bound to have an impact on the environment. This paper is aimed at modeling and analyzing the ecological level of minority cultural industries based on the background of the Internet of Things (IoT) and environmental responsibility. In the experiment, this paper analyzed the ecological level of the traditional fish skin industry by taking the Hezhe people in Heilongjiang as an example. Aiming at the cultural industry of the Hezhe people, this paper selected the fish skin industry as the object of empirical analysis from the fish culture it represents. According to the ecological level of the industry, this paper selected the three first-level indicators of production energy saving level, ecological environmental protection level, and production emission reduction level and its 12 subordinate second-level indicators to model and analyze the fish skin industry of the Hezhe people. The analysis results showed that the industrial ecological level of the Hezhe fish skin industry in the past 16 years reached the standard rate of more than 75%. However, the ecological level index for the three years of 2018, 2019, and 2020 was between 0.3 and 0.5, which indicated that the ecological level in these three years was very low. This was caused by the mechanization of the handicraft industry in recent years.

Van der Waals MoS2/Two-Dimensional Perovskite Heterostructure for Sensitive and Ultrafast Sub-Band-Gap Photodetection.

Two-dimensional (2D) hybrid perovskites have been extensively studied as the promising light-sensitive materials in the photodetectors owing to their improved structural stability over that of their three-dimensional counterparts. However, the application of the 2D perovskite-based photodetector in the near-infrared (NIR) region is obstructed by the large intrinsic optical band gap. Herein, we develop a novel van der Waals heterostructure composed of few-layer 2D perovskite/MoS2 nanoflakes, which exhibits high-sensitivity detection performance over a broad spectral region, from the visible region to the telecommunication wavelength (i.e., 1550 nm). In particular, the photoresponsivity and specific detectivity under an 860 nm laser reach 121 A W-1 and 4.3 × 1014 Jones, respectively, whereas the individual nanoflakes show no response under the same wavelength. Meanwhile, the response time at the microsecond (µs) level is obtained, shortened by around 3 orders of magnitude compared to that of the constituting layers. The sensitive and ultrafast photoresponse at the NIR wavelength stems from the strong interlayer transition of sub-band-gap photons and the rapid separation of the photogenerated carriers by the built-in field within the heterojunction area. Our results not only provide an effective approach to achieve sub-band-gap photodetection in 2D perovskite-based structures but also suggest a universal strategy to fabricate high-performance optoelectronic devices.