RESUMEN
There is a growing trend to apply field emission (FE) electron sources in vacuum electronic devices due to their fast response, high efficiency and low energy consumption compared to thermionic emission ones. Carbon nanotubes (CNTs) have been regarded as a promising class of electron field emitters since the 1990s and have promoted the development of FE technology greatly because of their high electrical and thermal conductivity, chemical stability, high aspect ratio and small size. Recent studies have shown that FE from CNTs has the potential to replace conventional thermionic emission in many areas and that it exhibits advanced features in practical applications. Consequently, FE from nanotubes and applications thereof have attracted much attention. This paper provides a comprehensive review of both recent advances in CNT field emitters and issues related to applications of CNT based FE. FE theories and principles are introduced, and the early development of field emitters is related. CNT emitter types and their FE performance are discussed. The current situation for applications based on nanotube FE is reviewed. Although challenges remain, the tremendous progress made in CNT FE over the past ten years indicates the field's development potential.
RESUMEN
This paper presents microelectromechanical system micromirrors with sidewall electrodes applied for use as a Confocal MACROscope for biomedical imaging. The MACROscope is a fluorescence and brightfield confocal laser scanning microscope with a very large field of view. In this paper, a microelectromechanical system mirror with sidewall electrodes replaces the galvo-scanner and XYZ-stage to improve the confocal MACROscope design and obtain an image. Two micromirror-based optical configurations are developed and tested to optimize the optical design through scanning angle, field of view and numerical aperture improvement. Meanwhile, the scanning frequency and control waveform of the micromirror are tested. Analysing the scan frequency and waveform becomes a key factor to optimize the micromirror-based confocal MACROscope. When the micromirror is integrated into the MACROscope and works at 40 Hz, the micromirror with open-loop control possesses good repeatability, so that the synchronization among the scanner, XYZ-stage and image acquisition can be realized. A laser scanning microscope system based on the micromirror with 2 µm width torsion bars was built and a 2D image was obtained as well. This work forms the experimental basis for building a practical confocal MACROscope.
RESUMEN
The extraordinary physical properties of quantum dot (QD) materials such as high radiation sensitivity and good radiation resistivity indicate their potential for use in the fabrication of radiation sensors. This paper reports the design and fabrication of two kinds of radiation sensors based on ZnO and CdTe QDs. Both sensors are characterized using a Gulmay Medical D3000 DXR unit for superficial x-ray irradiation with source photon energies that range from 36.9 to 64.9 keV. The QD radiation sensors exhibit excellent linearity with respect to different photon energy doses, radiation source to device surface distances, and field sizes. The effects of the electrode separation and the area density of the QD layer are also investigated. All sensors characterized show an outstanding repeatability under photon irradiation, with a signal variation less than 1%.
RESUMEN
Advances in microfabrication have introduced new possibilities for automated, high-throughput biomedical investigations and analysis. Physical effects such as dielectrophoresis (DEP) and AC electrokinetics can be used to manipulate particles in solution to coordinate a sequence of bioanalytical processing steps. DEP is accomplished with non-uniform electric fields that can polarize particles (microbeads, cells, viruses, DNA, proteins, etc.) in suspension causing translational or rotational movement. AC electrokinetics is another phenomena involved with movement of particles in suspension with electric fields and is comprised of both electro-thermal and electro-osmotic effects. This paper investigates single layer electrodes that are effective for particle localization and clustering based on DEP and AC electrokinetic effects. We demonstrate a novel multi-electrode setup capable of clustering particles into an array of discrete bands using activated and electrically floating electrodes. These bands shift to adjacent regions on the electrode surface by altering the electrode activation scheme. The predictability of particle placement to specific locations provides new opportunities for integration and coordination with raster scanning lasers or a charge coupled device (CCD) for advanced biomedical diagnostic devices, and more sophisticated optical interrogation techniques.
Asunto(s)
Biopolímeros/química , Biopolímeros/efectos de la radiación , Electroquímica/instrumentación , Electroforesis por Microchip/instrumentación , Separación Inmunomagnética/instrumentación , Microelectrodos , Micromanipulación/instrumentación , Biopolímeros/aislamiento & purificación , Electroquímica/métodos , Electroforesis por Microchip/métodos , Diseño de Equipo , Análisis de Falla de Equipo , Retroalimentación , Separación Inmunomagnética/métodos , Micromanipulación/métodos , Microesferas , Integración de SistemasRESUMEN
Carbon nanotubes (CNTs) have emerged as promising candidates for biomedical x-ray devices and other applications of field emission. CNTs grown/deposited in a thin film are used as cathodes for field emission. In spite of the good performance of such cathodes, the procedure to estimate the device current is not straightforward and the required insight towards design optimization is not well developed. In this paper, we report an analysis aided by a computational model and experiments by which the process of evolution and self-assembly (reorientation) of CNTs is characterized and the device current is estimated. The modeling approach involves two steps: (i) a phenomenological description of the degradation and fragmentation of CNTs and (ii) a mechanics based modeling of electromechanical interaction among CNTs during field emission. A computational scheme is developed by which the states of CNTs are updated in a time incremental manner. Finally, the device current is obtained by using the Fowler-Nordheim equation for field emission and by integrating the current density over computational cells. A detailed analysis of the results reveals the deflected shapes of the CNTs in an ensemble and the extent to which the initial state of geometry and orientation angles affect the device current. Experimental results confirm these effects.
RESUMEN
This paper presents an original device to enhance dielectrophoresis (DEP) effects through novel geometry of the electrodes. Implemented with a simple single-layer metal process, our microchip device consists of individually triangular-shaped electrodes in a parallel array. When activated with DEP waveforms, the novel-shaped electrodes generate horizontal bands of increasing electric fields. With these bands of electric fields, dielectric microbeads in a suitable medium can be manipulated to form a straight horizontal line at a predictable location over the electrodes. Further experiments show that the location of the microbeads is sensitive to the frequency of the applied DEP waveforms. By changing the frequencies, the line of microbeads can be shifted vertically along the electrodes. In addition, horizontal movements of the microbeads can be achieved with traveling wave DEP. With an accurate control of both vertical and horizontal positions and a potential multi-lane separation strategy, our device delivers substantial improvements over the existing electrode array devices.