Broad tuning range, high power quantum cascade laser at λ ∼ 7.4 µm.

In this article, we report a high power quantum cascade laser (QCL) at λ∼7.4 µm with a broad tuning range. By carefully designing and optimizing the active region and waveguide structure, a continuous-wave (CW) output power up to 1.36 W and 0.5 W is achieved at 293 K and 373 K which shows the excellent temperature stability. A high wall-plug efficiency (WPE) of 8% and 13.6% in CW and pulsed mode at 293 K are demonstrated. The laser shows a characteristic temperature T0 of 224 K and T1 of 381 K over a temperature range from 283 K to 373 K. In addition, a far field of pure zero order transverse mode and a fairly wide external cavity (EC) tuning range (280 cm-1) from 6.54 µm to 8 µm are achieved in pulsed operation. In addition, an EC single mode output power of 226 mW is obtained under CW operation at 293K.

GaSb surface grating distributed feedback interband cascade laser emitting at 3.25 µm.

A second-order distributed feedback interband cascade laser emitting at 3.25 µm was designed, grown, and fabricated. By coherent epitaxy of a GaSb cap layer instead of the conventional thin InAs cap on top of the laser structure, a high-quality surface grating was made of GaSb and gold. Enough coupling strength and a significant inter-modal loss difference were predicted according to the simulation within the framework of couple-wave theory. Lasers having 2-mm-long cavities and 4.5-µm-wide ridges with high-/anti-reflection coatings were fabricated. The continuous-wave threshold current and maximum single-mode output power were 60 mA and 24 mW at 20°C, respectively. The output power of 5 mW was still kept at 55°C. Continuous tuning free from mode hopping and high single-mode suppression ratios (>20 dB) were realized at all injection currents and heat-sink temperatures, covering a spectral range of over 20 cm-1.

Low voltage-defect quantum cascade lasers based on excited-states injection at λ ∼ 8.5 µm.

A quantum cascade laser emitting at λ∼8.5 µm based on the excited-state injection is presented. The operating voltage is reduced for a low-voltage defect in the excited-state design, compared with the conventional ground-state injection design. The threshold voltage and voltage defect are as low as 6.3 V and 54 mV for a 30-stage active region, respectively. Devices were fabricated through standard buried-heterostructure processing to decrease the heat accumulation. A continuous-wave optical power of 340 mW is obtained at 283 K with a threshold current density of 2.7 kA/cm2. Such a design has the potential to further improve the wall plug efficiency for increased voltage efficiency.

Room temperature continuous wave quantum dot cascade laser emitting at 7.2 µm.

We demonstrate a quantum cascade laser with active regions consisting of InAs quantum dots deposited on GaAs buffer layers that are embedded in InGaAs wells confined by InAlAs barriers. Continuous wave room temperature lasing at the wavelength of 7.2 µm has been demonstrated with the threshold current density as low as 1.89 kA/cm2, while in pulsed operational mode lasing at temperatures as high as 110 °C had been observed. A phenomenological theory explaining the improved performance due to weak localization of states had been formulated.

High efficiency, single-lobe surface-emitting DFB/DBR quantum cascade lasers.

We demonstrate a surface-emitting quantum cascade laser (QCL) based on second-order buried distributed feedback/distributed Bragg reflector (DFB/DBR) gratings for feedback and outcoupling. The grating fabricated beneath the waveguide was found to fundamentally favor lasing in symmetric mode either through analysis or experiment. Single-lobe far-field radiation pattern with full width at half maximum (FWHM) of 0.18° was obtained along the cavity-length direction. Besides, the buried DFB/DBR grating structure successfully provided an efficient vertical outcoupling mechanism with low optical losses, which manages to achieve a high surface outcouping efficiency of 46% in continuous-wave (CW) operation and 60% in pulsed operation at room temperature. Single-mode emission with a side-mode suppression ratio (SMSR) about 25 dB was continuously tunable by heat sink temperature or injection current. Our work contributes to the realization of high efficiency surface-emitting devices with high far-field beam quality that are significantly needed in many application fields.

Anomalous Mode Transitions in High Power Distributed Bragg Reflector Quantum Cascade Lasers.

In this paper, an anomalous spectral data of distributed Bragg reflector (DBR) quantum cascade lasers (QCLs) emitting around 7.6 µm is presented. The two-section DBR lasers, consisting of a gain section and an unpumped Bragg reflector, display an output power above 0.6 W in continuous wave (CW) mode at room temperature. The anomalous spectral data is defined as a longitudinal mode which moves toward shorter wavelengths with increasing temperature or injection current, which is unexpected. Although the longer wavelength modes are expected to start lasing when raising device temperature or injection current, occasional mode hops to a shorter wavelength are seen. These anomalous mode transitions are explained by means of modal analysis. The thermal-induced change of the refractive index implied by an increase in the temperature or injection current yields nearly periodic transitions between cavity modes.

Demonstration of High-Power and Stable Single-Mode in a Quantum Cascade Laser Using Buried Sampled Grating.

High-power, low-threshold stable single-mode operation buried distributed feedback quantum cascade laser by incorporating sampled grating emitting at λ ~ 4.87 µm is demonstrated. The high continuous wave (CW) output power of 948 mW and 649 mW for a 6-mm and 4-mm cavity length is obtained at 20 °C, respectively, which benefits from the optimized optical field distribution of sampled grating. The single-mode yields of the devices are obviously enhanced by controlling cleaved positions of the two end facets precisely. As a result, stable single-mode emission and mode tuning linearly without any mode hopping of devices are obtained under the different heat sink temperatures or high injection currents.

Tapered Quantum Cascade Laser Arrays Integrated with Talbot Cavities.

Power scaling in broad area quantum cascade laser (QCL) usually leads to the deterioration of the beam quality with an emission of multiple lobes far-field pattern. In this letter, we demonstrate a tapered QCL array integrated with Talbot cavity at one side of the array. Fundamental supermode operation is achieved in the arrays with taper straight-end connected to the Talbot cavity. Lateral far-field of the fundamental supermode shows a near diffraction limited beam divergence of 2.7°. The output power of a five-element array is about three times as high as a single-ridge laser with an emission wavelength of around 4.8 µm. However, arrays with the taper-end connected to the Talbot cavity always show a high-order supermode operation whatever Talbot cavity length is.

Stable Single-Mode Operation of Distributed Feedback Quantum Cascade Laser by Optimized Reflectivity Facet Coatings.

In this work, quantum cascade lasers (QCLs) based on strain compensation combined with two-phonon resonance design are presented. Distributed feedback (DFB) laser emitting at ~ 4.76 µm was fabricated through a standard buried first-order grating and buried heterostructure (BH) processing. Stable single-mode emission is achieved under all injection currents and temperature conditions without any mode hop by the optimized antireflection (AR) coating on the front facet. The AR coating consists of a double layer dielectric of Al2O3 and Ge. For a 2-mm laser cavity, the maximum output power of the AR-coated DFB-QCL was more than 170 mW at 20 °C with a high wall-plug efficiency (WPE) of 4.7% in a continuous-wave (CW) mode.

Low Power Consumption Substrate-Emitting DFB Quantum Cascade Lasers.

In the present work, an ultra-low power consumption substrate-emitting distributed feedback (DFB) quantum cascade laser (QCL) was developed. The continuous-wave (CW) threshold power dissipation is reduced to 0.43 W at 25 °C by shortening the cavity length to 0.5 mm and depositing high-reflectivity (HR) coating on both facets. As far as we know, this is the recorded threshold power dissipation of QCLs in the same conditions. Single-mode emission was achieved by employing a buried second-order grating. Mode-hop free emission can be observed within a wide temperature range from 15 to 105 °C in CW mode. The divergence angles are 22.5o and 1.94o in the ridge-width direction and cavity-length direction, respectively. The maximum optical power in CW operation was 2.4 mW at 25 °C, which is sufficient to spectroscopy applications.

High Efficiency, Low Power-Consumption DFB Quantum Cascade Lasers Without Lateral Regrowth.

Very low power-consumption distributed feedback (DFB) quantum cascade lasers (QCLs) at the wavelength around 4.9 µm were fabricated by conventional process without lateral regrowth of InP:Fe or using sidewall grating. Benefitted from the optimized materials and low waveguide loss, very low threshold current density of 0.5 kA/cm2 was obtained for a device with cavity length of 2 mm. Combined with the partial-high-reflection coating, the 1-mm-long DFB QCL achieved low power-consumption continuous wave (CW) operation up to 105 °C. The CW threshold power-consumptions were 0.72 and 0.78 W at 15 and 25 °C, respectively. The maximum CW output power was over 110 mW at 15 °C and still more than 35 mW at 105 °C. At 15 °C, wall-plug efficiency of 5.5% and slope efficiency of 1.8 W/A were deduced, which were very high for low power-consumption DFB QCLs.

Normal Incident Long Wave Infrared Quantum Dash Quantum Cascade Photodetector.

We demonstrate a quantum dash quantum cascade photodetector (QDash-QCD) by incorporating self-assembled InAs quantum dashes into the active region of a long wave infrared QCD. Sensitive photoresponse to normal incident light at 10 µm was observed, which is attributed to the intersubband (ISB) transitions in the quantum well/quantum dash (QW/QDash) hybrid absorption region and the following transfer of excited electrons on the extraction stair-like quantum levels separated by LO-phonon energy. The high density InAs quantum dashes were formed in the Stranski-Krastanow mode and stair-like levels were formed by a lattice matched InGaAs/InAlAs superlattice. A stable responsivity from 5 mA/W at 77 K to 3 mA/W at as high as 190 K was observed, which makes the QDash-QCD promising in high temperature operation.

A Polarization-Dependent Normal Incident Quantum Cascade Detector Enhanced Via Metamaterial Resonators.

The design, fabrication, and characterization of a polarization-dependent normal incident quantum cascade detector coupled via complementary split-ring metamaterial resonators in the infrared regime are presented. The metamaterial structure is designed through three-dimensional finite-difference time-domain method and fabricated on the top metal contact, which forms a double-metal waveguide together with the metallic ground plane. With normal incidence, significant enhancements of photocurrent response are obtained at the metamaterial resonances compared with the 45° polished edge coupling device. The photocurrent response enhancements exhibit clearly polarization dependence, and the largest response enhancement factor of 165% is gained for the incident light polarized parallel to the split-ring gap.

10-W pulsed operation of substrate emitting photonic-crystal quantum cascade laser with very small divergence.

High-power broad area substrate emitting photonic-crystal distributed feedback (DFB) quantum cascade lasers (QCLs) emitting around 4.73 µm is reported. Two-dimensional centered rectangular photonic-crystal (CRPC) grating is introduced to enhance optical coherence in large area device. Main lobe far-field radiation pattern with a very small divergence angle of about 0.65° × 0.31° is obtained. A record peak output power for vertical emitting QCLs exceeding 10 W is obtained with high reflectivity (HR) coating. Robust single longitudinal mode emission with a side mode suppression ratio (SMSR) of 30 dB is continuously tunable by the heat sink temperature up to 65°C.

Quantum dot cascade laser.

We demonstrated an unambiguous quantum dot cascade laser based on InGaAs/GaAs/InAs/InAlAs heterostructure by making use of self-assembled quantum dots in the Stranski-Krastanow growth mode and two-step strain compensation active region design. The prototype generates stimulated emission at λ ~ 6.15 µm and a broad electroluminescence band with full width at half maximum over 3 µm. The characteristic temperature for the threshold current density within the temperature range of 82 to 162 K is up to 400 K. Moreover, our materials show the strong perpendicular mid-infrared response at about 1,900 cm-1. These results are very promising for extending the present laser concept to terahertz quantum cascade laser, which would lead to room temperature operation. PACS: 42.55.Px; 78.55.Cr; 78.67.Hc.