A novel electrochemical flow-cell for operando XAS investigations in X-ray opaque supports.

Improvement of electrochemical technologies is one of the most popular topics in the field of renewable energy. However, this process requires a deep understanding of the electrode-electrolyte interface behavior under operando conditions. X-ray absorption spectroscopy (XAS) is widely employed to characterize electrode materials, providing element-selective oxidation state and local structure. Several existing cells allow studies as close as possible to realistic operating conditions, but most of them rely on the deposition of the electrodes on conductive and X-ray transparent materials, from where the radiation impinges the sample. In this work, we present a new electrochemical flow-cell for operando XAS that can be used with X-ray opaque substrates, since the signal is effectively detected from the electrode surface, as the radiation passes through a thin layer of electrolyte (∼17 µm). The electrolyte can flow over the electrode, reducing bubble formation and avoiding strong reactant concentration gradients. We show that high-quality data can be obtained under operando conditions, thanks to the high efficiency of the cell from the hard X-ray regime down to ∼4 keV. We report as a case study the operando XAS investigation at the Fe and Ni K-edges on Ni-doped γ-Fe2O3 films, epitaxially grown on Pt substrates. The effect of the Ni content on the catalytic performances for the oxygen evolution reaction is discussed.

Structural and Reactivity Effects of Secondary Metal Doping into Iron-Nitrogen-Carbon Catalysts for Oxygen Electroreduction.

While improved activity was recently reported for bimetallic iron-metal-nitrogen-carbon (FeMNC) catalysts for the oxygen reduction reaction (ORR) in acid medium, the nature of active sites and interactions between the two metals are poorly understood. Here, FeSnNC and FeCoNC catalysts were structurally and catalytically compared to their parent FeNC and SnNC catalysts. While CO cryo-chemisorption revealed a twice lower site density of M-Nx sites for FeSnNC and FeCoNC relative to FeNC and SnNC, the mass activity of both bimetallic catalysts is 50-100% higher than that of FeNC due to a larger turnover frequency in the bimetallic catalysts. Electron microscopy and X-ray absorption spectroscopy identified the coexistence of Fe-Nx and Sn-Nx or Co-Nx sites, while no evidence was found for binuclear Fe-M-Nx sites. 57Fe Mössbauer spectroscopy revealed that the bimetallic catalysts feature a higher D1/D2 ratio of the spectral signatures assigned to two distinct Fe-Nx sites, relative to the FeNC parent catalyst. Thus, the addition of the secondary metal favored the formation of D1 sites, associated with the higher turnover frequency.

Doped Graphene To Mimic the Bacterial NADH Oxidase for One-Step NAD+ Supplementation in Mammals.

Nicotinamide adenine dinucleotide (NAD) is a critical regulator of metabolic networks, and declining levels of its oxidized form, NAD+, are closely associated with numerous diseases. While supplementing cells with precursors needed for NAD+ synthesis has shown poor efficacy in combatting NAD+ decline, an alternative strategy is the development of synthetic materials that catalyze the oxidation of NADH into NAD+, thereby taking over the natural role of the NADH oxidase (NOX) present in bacteria. Herein, we discovered that metal-nitrogen-doped graphene (MNGR) materials can catalyze the oxidation of NADH into NAD+. Among MNGR materials with different transition metals, Fe-, Co-, and Cu-NGR displayed strong catalytic activity combined with >80% conversion of NADH into NAD+, similar specificity to NOX for abstracting hydrogen from the pyridine ring of nicotinamide, and higher selectivity than 51 other nanomaterials. The NOX-like activity of FeNGR functioned well in diverse cell lines. As a proof of concept of the in vivo application, we showed that FeNGR could specifically target the liver and remedy the metabolic flux anomaly in obesity mice with NAD+-deficient cells. Overall, our study provides a distinct insight for exploration of drug candidates by design of synthetic materials to mimic the functions of unique enzymes (e.g., NOX) in bacteria.

Heterostructured Cobalt Silicide Nanocrystals: Synthesis in Molten Salts, Ferromagnetism, and Electrocatalysis.

Nanoscale heterostructures of covalent intermetallics should give birth to a wide range of interface-driven physical and chemical properties. Such a level of design however remains unattainable for most of these compounds, due to the difficulty to reach a crystalline order of covalent bonds at the moderate temperatures required for colloidal chemistry. Herein, we design heterostructured cobalt silicide nanoparticles to trigger magnetic and catalytic properties in silicon-based materials. Our strategy consists in controlling the diffusion of cobalt atoms into silicon nanoparticles, by reacting these particles in molten salts. By adjusting the temperature, we tune the conversion of the initial silicon particles toward homogeneous CoSi nanoparticles and core-shell nanoparticles made of a CoSi shell and a silicon-rich core. The increased interface-to-volume ratio of the CoSi component in the core-shell particles yields distinct properties compared to the bulk and homogeneous nanoparticles. First, the core-shell particles exhibit increased ferromagnetism, despite the bulk diamagnetic properties of cobalt monosilicide. Second, the core-shell nanoparticles act as efficient precatalysts for alkaline water oxidation, where the nanostructure is converted in situ into a layered cobalt silicon oxide/(oxy)hydroxide with high and stable oxygen evolution reaction (OER) electrocatalytic activity. This work demonstrates a route to design heterostructured nanocrystals of covalent intermetallic compounds and shows that these new structures exhibit very rich, yet poorly explored, interface-based physical properties and reactivity.

How Nanoparticles Modify Adsorbed Proteins: Impact of Silica Nanoparticles on the Hemoglobin Active Site.

The adsorption of proteins on surfaces has been studied for a long time, but the relationship between the structural and functional properties of the adsorbed protein and the adsorption mechanism remains unclear. Using hemoglobin adsorbed on silica nanoparticles, we have previously shown that hemoglobin's affinity towards oxygen increases with adsorption. Nevertheless, it was also shown that there were no significant changes in the quaternary and secondary structures. In order to understand the change in activity, we decided in this work to focus on the active sites of hemoglobin, the heme and its iron. After measuring adsorption isotherms of porcine hemoglobin on Ludox silica nanoparticles, we analyzed the structural modifications of adsorbed hemoglobin by X-ray absorption spectroscopy and circular dichroism spectra in the Soret region. It was found that upon adsorption, there were modifications in the heme pocket environment due to changes in the angles of the heme vinyl functions. These alterations can explain the greater affinity observed.

Silver and Copper Nitride Cooperate for CO Electroreduction to Propanol.

The need of carbon sources for the chemical industry, alternative to fossil sources, has pointed to CO2 as a possible feedstock. While CO2 electroreduction (CO2 R) allows production of interesting organic compounds, it suffers from large carbon losses, mainly due to carbonate formation. This is why, quite recently, tandem CO2 R, a two-step process, with first CO2 R to CO using a solid oxide electrolysis cell followed by CO electroreduction (COR), has been considered, since no carbon is lost as carbonate in either step. Here we report a novel copper-based catalyst, silver-doped copper nitride, with record selectivity for formation of propanol (Faradaic efficiency: 45 %), an industrially relevant compound, from CO electroreduction in gas-fed flow cells. Selective propanol formation occurs at metallic copper atoms derived from copper nitride and is promoted by silver doping as shown experimentally and computationally. In addition, the selectivity for C2+ liquid products (Faradaic efficiency: 80 %) is among the highest reported so far. These findings open new perspectives regarding the design of catalysts for production of C3 compounds from CO2 .

Oxygen Reduction Reaction in Alkaline Media Causes Iron Leaching from Fe-N-C Electrocatalysts.

The electrochemical activity of modern Fe-N-C electrocatalysts in alkaline media is on par with that of platinum. For successful application in fuel cells (FCs), however, also high durability and longevity must be demonstrated. Currently, a limited understanding of degradation pathways, especially under operando conditions, hinders the design and synthesis of simultaneously active and stable Fe-N-C electrocatalysts. In this work, using a gas diffusion electrode half-cell coupled with inductively coupled plasma mass spectrometry setup, Fe dissolution is studied under conditions close to those in FCs, that is, with a porous catalyst layer (CL) and at current densities up to -125 mA·cm-2. Varying the rate of the oxygen reduction reaction (ORR), we show a remarkable linear correlation between the Faradaic charge passed through the electrode and the amount of Fe dissolved from the electrode. This finding is rationalized assuming that oxygen reduction and Fe dissolution reactions are interlinked, likely through a common intermediate formed during the Fe redox transitions in Fe species involved in the ORR, such as FeNxCy and Fe3C@N-C. Moreover, such a linear correlation allows the application of a simple metric─S-number─to report the material's stability. Hence, in the current work, a powerful tool for a more applied stability screening of different electrocatalysts is introduced, which allows on the one hand fast performance investigations under more realistic conditions, and on the other hand a more advanced mechanistic understanding of Fe-N-C degradation in CLs.

Au and Pt Remain Unoxidized on a CeO2-Based Catalyst during the Water-Gas Shift Reaction.

The active forms of Au and Pt in CeO2-based catalysts for the water-gas shift (WGS) reaction are an issue that remains unclear, although it has been widely studied. On one hand, ionic species might be responsible for weakening the Ce-O bonds, thus increasing the oxygen mobility and WGS activity. On the other hand, the close contact of Au or Pt atoms with CeO2 oxygen vacancies at the metal-CeO2 interface might provide the active sites for an efficient reaction. In this work, using in situ X-ray absorption spectroscopy, we demonstrate that both Au and Pt remain unoxidized during the reaction. Remarkable differences involving the dynamics established by both species under WGS atmospheres were recognized. For the prereduced Pt catalyst, the increase of the conversion coincided with a restructuration of the Pt atoms into cuboctahedrical metallic particles without significant variations on the overall particle size. Contrary to the relatively static behavior of Pt0, Au0 nanoparticles exhibited a sequence of particle splitting and agglomeration while maintaining a zero oxidation state despite not being located in a metallic environment during the process. High WGS activity was obtained when Au atoms were surrounded by oxygen. The fact that Au preserves its unoxidized state indicates that the chemical interaction between Au and oxygen must be necessarily electrostatic and that such an electrostatic interaction is fundamental for a top performance in the WGS process.

Iron Insertion at the Assembly Site of the ISCU Scaffold Protein Is a Conserved Process Initiating Fe-S Cluster Biosynthesis.

Iron-sulfur (Fe-S) clusters are prosthetic groups of proteins biosynthesized on scaffold proteins by highly conserved multi-protein machineries. Biosynthesis of Fe-S clusters into the ISCU scaffold protein is initiated by ferrous iron insertion, followed by sulfur acquisition, via a still elusive mechanism. Notably, whether iron initially binds to the ISCU cysteine-rich assembly site or to a cysteine-less auxiliary site via N/O ligands remains unclear. We show here by SEC, circular dichroism (CD), and Mössbauer spectroscopies that iron binds to the assembly site of the monomeric form of prokaryotic and eukaryotic ISCU proteins via either one or two cysteines, referred to the 1-Cys and 2-Cys forms, respectively. The latter predominated at pH 8.0 and correlated with the Fe-S cluster assembly activity, whereas the former increased at a more acidic pH, together with free iron, suggesting that it constitutes an intermediate of the iron insertion process. Iron not binding to the assembly site was non-specifically bound to the aggregated ISCU, ruling out the existence of a structurally defined auxiliary site in ISCU. Characterization of the 2-Cys form by site-directed mutagenesis, CD, NMR, X-ray absorption, Mössbauer, and electron paramagnetic resonance spectroscopies showed that the iron center is coordinated by four strictly conserved amino acids of the assembly site, Cys35, Asp37, Cys61, and His103, in a tetrahedral geometry. The sulfur receptor Cys104 was at a very close distance and apparently bound to the iron center when His103 was missing, which may enable iron-dependent sulfur acquisition. Altogether, these data provide the structural basis to elucidate the Fe-S cluster assembly process and establish that the initiation of Fe-S cluster biosynthesis by insertion of a ferrous iron in the assembly site of ISCU is a conserved mechanism.

P-block single-metal-site tin/nitrogen-doped carbon fuel cell cathode catalyst for oxygen reduction reaction.

This contribution reports the discovery and analysis of a p-block Sn-based catalyst for the electroreduction of molecular oxygen in acidic conditions at fuel cell cathodes; the catalyst is free of platinum-group metals and contains single-metal-atom actives sites coordinated by nitrogen. The prepared SnNC catalysts meet and exceed state-of-the-art FeNC catalysts in terms of intrinsic catalytic turn-over frequency and hydrogen-air fuel cell power density. The SnNC-NH3 catalysts displayed a 40-50% higher current density than FeNC-NH3 at cell voltages below 0.7 V. Additional benefits include a highly favourable selectivity for the four-electron reduction pathway and a Fenton-inactive character of Sn. A range of analytical techniques combined with density functional theory calculations indicate that stannic Sn(IV)Nx single-metal sites with moderate oxygen chemisorption properties and low pyridinic N coordination numbers act as catalytically active moieties. The superior proton-exchange membrane fuel cell performance of SnNC cathode catalysts under realistic, hydrogen-air fuel cell conditions, particularly after NH3 activation treatment, makes them a promising alternative to today's state-of-the-art Fe-based catalysts.

Potential-Induced Spin Changes in Fe/N/C Electrocatalysts Assessed by In Situ X-ray Emission Spectroscopy.

The commercial success of the electrochemical energy conversion technologies required for the decarbonization of the energy sector requires the replacement of the noble metal-based electrocatalysts currently used in (co-)electrolyzers and fuel cells with inexpensive, platinum-group metal-free analogs. Among these, Fe/N/C-type catalysts display promising performances for the reduction of O2 or CO2 , but their insufficient activity and stability jeopardize their implementation in such devices. To circumvent these issues, a better understanding of the local geometric and electronic structure of their catalytic active sites under reaction conditions is needed. Herein we shed light on the electronic structure of the molecular sites in two Fe/N/C catalysts by probing their average spin state with X-ray emission spectroscopy (XES). Chiefly, our in situ XES measurements reveal for the first time the existence of reversible, potential-induced spin state changes in these materials.

Evolution Pathway from Iron Compounds to Fe1(II)-N4 Sites through Gas-Phase Iron during Pyrolysis.

Pyrolysis is indispensable for synthesizing highly active Fe-N-C catalysts for the oxygen reduction reaction (ORR) in acid, but how Fe, N, and C precursors transform to ORR-active sites during pyrolysis remains unclear. This knowledge gap obscures the connections between the input precursors and the output products, clouding the pathway toward Fe-N-C catalyst improvement. Herein, we unravel the evolution pathway of precursors to ORR-active catalyst comprised exclusively of single-atom Fe1(II)-N4 sites via in-temperature X-ray absorption spectroscopy. The Fe precursor transforms to Fe oxides below 300 °C and then to tetrahedral Fe1(II)-O4 via a crystal-to-melt-like transformation below 600 °C. The Fe1(II)-O4 releases a single Fe atom that diffuses into the N-doped carbon defect forming Fe1(II)-N4 above 600 °C. This vapor-phase single Fe atom transport mechanism is verified by synthesizing Fe1(II)-N4 sites via "noncontact pyrolysis" wherein the Fe precursor is not in physical contact with the N and C precursors during pyrolysis.

Evidence for an egg-box-like structure in iron(ii)-polygalacturonate hydrogels: a combined EXAFS and molecular dynamics simulation study.

The local structure of Fe2+ in Fe2+-polygalacturonic acid (polyGalA) hydrogels has been studied by coupling Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy and molecular dynamics (MD) simulation. The EXAFS fitting results reveal an octahedral coordination geometry of Fe2+ both in aqueous solution and in the hydrogel, with similar Fe-O distances (2.09 ± 0.01 Å in the hydrogel and 2.11 ± 0.01 Å in aqueous solution). The MD simulations evidence that standard empirical force fields are unable to accurately reproduce the EXAFS spectra of Fe2+ in both aqueous solution and hydrogel. Based on the EXAFS distance determinations, we then performed restrained MD simulations of hypothetical octahedral coordination modes of Fe2+ with polyGalA chains. The best agreement between experimental and simulated EXAFS spectra was found when Fe2+ is monodentately coordinated to two carboxylate and two hydroxyl oxygens from a pair of polyGalA chains as well as to two water oxygens in an octahedral coordination geometry compatible with the "egg-box model".

On the Influence of Oxygen on the Degradation of Fe-N-C Catalysts.

Fe-N-C catalysts containing atomic FeNx sites are promising candidates as precious-metal-free catalysts for oxygen reduction reaction (ORR) in proton exchange membrane fuel cells. The durability of Fe-N-C catalysts in fuel cells has been extensively studied using accelerated stress tests (AST). Herein we reveal stronger degradation of the Fe-N-C structure and four-times higher ORR activity loss when performing load cycling AST in O2 - vs. Ar-saturated pH 1 electrolyte. Raman spectroscopy results show carbon corrosion after AST in O2 , even when cycling at low potentials, while no corrosion occurred after any load cycling AST in Ar. The load-cycling AST in O2 leads to loss of a significant fraction of FeNx sites, as shown by energy dispersive X-ray spectroscopy analyses, and to the formation of Fe oxides. The results support that the unexpected carbon corrosion occurring at such low potential in the presence of O2 is due to reactive oxygen species produced between H2 O2 and Fe sites via Fenton reactions.

Activity-Selectivity Trends in the Electrochemical Production of Hydrogen Peroxide over Single-Site Metal-Nitrogen-Carbon Catalysts.

Nitrogen-doped carbon materials featuring atomically dispersed metal cations (M-N-C) are an emerging family of materials with potential applications for electrocatalysis. The electrocatalytic activity of M-N-C materials toward four-electron oxygen reduction reaction (ORR) to H2O is a mainstream line of research for replacing platinum-group-metal-based catalysts at the cathode of fuel cells. However, fundamental and practical aspects of their electrocatalytic activity toward two-electron ORR to H2O2, a future green "dream" process for chemical industry, remain poorly understood. Here we combined computational and experimental efforts to uncover the trends in electrochemical H2O2 production over a series of M-N-C materials (M = Mn, Fe, Co, Ni, and Cu) exclusively comprising atomically dispersed M-Nx sites from molecular first-principles to bench-scale electrolyzers operating at industrial current density. We investigated the effect of the nature of a 3d metal within a series of M-N-C catalysts on the electrocatalytic activity/selectivity for ORR (H2O2 and H2O products) and H2O2 reduction reaction (H2O2RR). Co-N-C catalyst was uncovered with outstanding H2O2 productivity considering its high ORR activity, highest H2O2 selectivity, and lowest H2O2RR activity. The activity-selectivity trend over M-N-C materials was further analyzed by density functional theory, providing molecular-scale understandings of experimental volcano trends for four- and two-electron ORR. The predicted binding energy of HO* intermediate over Co-N-C catalyst is located near the top of the volcano accounting for favorable two-electron ORR. The industrial H2O2 productivity over Co-N-C catalyst was demonstrated in a microflow cell, exhibiting an unprecedented production rate of more than 4 mol peroxide gcatalyst-1 h-1 at a current density of 50 mA cm-2.

Tuning the Structure of Galacturonate Hydrogels: External Gelation by Ca, Zn, or Fe Cationic Cross-Linkers.

We show here how the nature of various divalent cations M2+ (Ca2+, Zn2+, or Fe2+) influences the structure and mechanical properties of ionotropic polygalacturonate (polyGal) hydrogels designed by the diffusion of cations along one direction (external gelation). All hydrogels exhibit strong gradients of polyGal and cation concentrations, which are similar for all studied cations with a constant ratio R = [M2+]/[Gal] equal to 0.25, showing that every M2+ cation interacts with four galacturonate (Gal) units all along the gels. The regions of the hydrogels formed in the early stages of the gelation process are also similar for all cations and are homogeneous, with the same characteristic mesh size (75 ± 5 Å, as measured by small angle neutron scattering (SANS)) and the same storage modulus G' (∼5 × 104 Pa). Conversely, in the regions of the gels formed in later stages of the process there exist differences in mechanical properties, turbidity, and local structure from one cation to another. Zn(II)-polyGal and Fe(II)-polyGal hydrogels display mesoscopic heterogeneities, more marked in case of Fe than for Zn, that are not present in Ca(II)-polyGal hydrogels. This comes from the mode and the strength of association between the cation and the Gal unit (bidentate for Ca2+ and monodentate "egg-box" for Zn2+ and Fe2+). Cross-links formed by Zn2+ and Fe2+ have a higher stability (lower ability to untie and reform) that induces the formation of local heterogeneities in the early stages of the gelation process whose size progressively increases during the gel growth, a mechanism that does not occur for cross-links made by Ca2+ that are less stable and enable possible reorganizations between polyGal chains.

Electroreduction of CO2 on Single-Site Copper-Nitrogen-Doped Carbon Material: Selective Formation of Ethanol and Reversible Restructuration of the Metal Sites.

It is generally believed that CO2 electroreduction to multi-carbon products such as ethanol or ethylene may be catalyzed with significant yield only on metallic copper surfaces, implying large ensembles of copper atoms. Here, we report on an inexpensive Cu-N-C material prepared via a simple pyrolytic route that exclusively feature single copper atoms with a CuN4 coordination environment, atomically dispersed in a nitrogen-doped conductive carbon matrix. This material achieves aqueous CO2 electroreduction to ethanol at a Faradaic yield of 55 % under optimized conditions (electrolyte: 0.1 m CsHCO3 , potential: -1.2 V vs. RHE and gas-phase recycling set up), as well as CO electroreduction to C2 -products (ethanol and ethylene) with a Faradaic yield of 80 %. During electrolysis the isolated sites transiently convert into metallic copper nanoparticles, as shown by operando XAS analysis, which are likely to be the catalytically active species. Remarkably, this process is reversible and the initial material is recovered intact after electrolysis.

Identification of catalytic sites for oxygen reduction in iron- and nitrogen-doped graphene materials.

While platinum has hitherto been the element of choice for catalysing oxygen electroreduction in acidic polymer fuel cells, tremendous progress has been reported for pyrolysed Fe-N-C materials. However, the structure of their active sites has remained elusive, delaying further advance. Here, we synthesized Fe-N-C materials quasi-free of crystallographic iron structures after argon or ammonia pyrolysis. These materials exhibit nearly identical Mössbauer spectra and identical X-ray absorption near-edge spectroscopy (XANES) spectra, revealing the same Fe-centred moieties. However, the much higher activity and basicity of NH3-pyrolysed Fe-N-C materials demonstrates that the turnover frequency of Fe-centred moieties depends on the physico-chemical properties of the support. Following a thorough XANES analysis, the detailed structures of two FeN4 porphyrinic architectures with different O2 adsorption modes were then identified. These porphyrinic moieties are not easily integrated in graphene sheets, in contrast with Fe-centred moieties assumed hitherto for pyrolysed Fe-N-C materials. These new insights open the path to bottom-up synthesis approaches and studies on site-support interactions.

Synergy between molybdenum nitride and gold leading to platinum-like activity for hydrogen evolution.

Reduced size and direct electrochemical H2 compression are two distinct advantages of electrolyzers based on the acid-polymer electrolyte membrane technology over those relying on alkaline electrolytes. However, recourse to catalysts based on the scarce platinum-group-metals has hitherto been the price to pay. While the transition metal sulfides and nitrides of group VI have recently shown interesting activities for H2 evolution, the remaining activity gap with Pt needs to be reduced. Platinum owes its high activity to its optimum metal-hydrogen bond strength for H2 evolution, which is a proven descriptor of the activity on single-component catalysts. Here, we unravel a major synergetic effect between gold and molybdenum nitride which multiplies the hydrogen evolution activity ca. 100 times over that of either gold or molybdenum nitride. This two-phase catalytic material, featuring both strong and weak metal-hydrogen bonds, overcomes the limitations described by Sabatier's principle for single-component catalysts.