Biomechanical effects of a titanium intervertebral cage as a stand-alone device, and in combination with locking plates in the canine caudal cervical spine.

OBJECTIVE: To evaluate the change in ex vivo biomechanical properties of the canine cervical spine, due to an intervertebral cage, both as a stand-alone device and in combination with plates. STUDY DESIGN: Experimental ex vivo study. ANIMALS: Cervical spinal segments (C5-C7) from eight canine cadavers. METHODS: The range of motion (ROM) and elastic zone stiffness (EZS) of the spines were determined with a four-point bending device in flexion/extension, lateral bending, and axial rotation for four conditions: native, discectomy, cage (at C6-C7), and cage with plates (at C6-C7). The disc height index (DHI) for each condition was determined using radiography. RESULTS: Discectomy resulted in overall increased ROM (p < .01) and EZS (p < .05) and decreased DHI (p < .005) when compared to the native condition. Placement of the cage increased DHI (p < .001) and restored total ROM during flexion/extension, lateral bending and axial rotation, and EZS during flexion/extension to the level of the native spine. Application of the plates further reduced the total ROM during flexion/extension (p < .001) and lateral bending (p < .001), but restored ROM in extension and EZS during lateral bending. No implant failure, subsidence, or significant cage migration occurred during loading. CONCLUSION: An anchorless intervertebral cage used as a stand-alone device was able to restore the disc height and spinal stability to the level of the native cervical spine, whereas the addition of plates further reduced the spinal unit mobility. CLINICAL SIGNIFICANCE: This study implies that the intervertebral cage may be used as a stand-alone device in the spinal unit fixation in the canine cervical spine.

The effect of PPARγ inhibition on bone marrow adipose tissue and bone in C3H/HeJ mice.

Bone marrow adipose tissue (BMAT) increases after menopause, and increased BMAT is associated with osteoporosis and prevalent vertebral fractures. Peroxisome proliferator-activated receptor-γ (PPARγ) activation promotes adipogenesis and inhibits osteoblastogenesis; therefore, PPARγ is a potential contributor to the postmenopausal increase in BMAT and decrease in bone mass. The aim of this study is to determine if PPARγ inhibition can prevent ovariectomy-induced BMAT increase and bone loss in C3H/HeJ mice. Fourteen-week-old female C3H/HeJ mice ( n = 40) were allocated to four intervention groups: sham surgery (Sham) or ovariectomy (OVX; isoflurane anesthesia) with either vehicle (Veh) or PPARγ antagonist administration (GW9662; 1 mg·kg-1·day-1, daily intraperitoneal injections) for 3 wk. We measured BMAT volume, adipocyte size, adipocyte number. and bone structural parameters in the proximal metaphysis of the tibia using polyoxometalate-based contrast enhanced-nanocomputed topogaphy. Bone turnover was measured in the contralateral tibia using histomorphometry. The effects of surgery and treatment were analyzed by two-way ANOVA. OVX increased the BMAT volume fraction (Sham + Veh: 2.9 ± 2.7% vs. OVX + Veh: 8.1 ± 5.0%: P < 0.001), average adipocyte diameter (Sham + Veh: 19.3 ± 2.6 µm vs. OVX + Veh: 23.1 ± 3.4 µm: P = 0.001), and adipocyte number (Sham + Veh: 584 ± 337cells/µm3 vs. OVX + Veh: 824 ± 113cells/µm3: P = 0.03), while OVX decreased bone volume fraction (Sham + Veh: 15.5 ± 2.8% vs. OVX + Veh: 7.7 ± 1.9%; P < 0.001). GW9662 had no effect on BMAT, bone structural parameters, or bone turnover. In conclusion, ovariectomy increased BMAT and decreased bone volume in C3H/HeJ mice. The PPARγ antagonist GW9662 had no effect on BMAT or bone volume in C3H/HeJ mice, suggesting that BMAT accumulation is regulated independently of PPARγ in C3H/HeJ mice.

Changes in Intervertebral Disk Mechanical Behavior During Early Degeneration.

Intervertebral disk (IVD) degeneration is commonly described by loss of height and hydration. However, in the first stage of IVD degeneration, this loss has not yet occurred. In the current study, we use an ex vivo degeneration model to analyze the changes in IVDs mechanical behavior in the first phase of degeneration. We characterize these changes by stretched-exponential fitting, and suggest the fitted parameters as markers for early degeneration. Enzymatic degeneration of healthy lumbar caprine IVDs was induced by injecting 100 µL of Chondroïtinase ABC (Cabc) into the nucleus. A no-intervention and phosphate buffered saline (PBS) injected group were used as controls. IVDs were cultured in a bioreactor for 20 days under diurnal, simulated-physiological loading (SPL) conditions. Disk deformation was continuously monitored. Changes in disk height recovery behavior were quantified using stretched-exponential fitting. Disk height, histological sections, and water- and glycosaminoglycan (GAG)-content measurements were used as gold standards for the degenerative state. Cabc injection caused significant GAG loss from the nucleus and had detrimental effects on poro-elastic mechanical properties of the IVDs. These were progressive over time, with a propensity toward more linear recovery behavior. On histological sections, both PBS and Cabc injected IVDs showed moderate degeneration. A small GAG loss yields changes in IVD recovery behavior, which can be quantified with stretched-exponential fitting. Parameters changed significantly compared to control. Studies on disk degeneration and biomaterial engineering for degenerative disk disease (DDD) could benefit from focusing on IVD biomechanical behavior rather than height and water-content, as a marker for early disk degeneration.

Intradiscal pressure depends on recent loading and correlates with disc height and compressive stiffness.

PURPOSE: Intervertebral discs exhibit time-dependent deformation (creep), which could influence the relation between applied stress and intradiscal pressure. This study investigates the effect of prolonged dynamic loading on intradiscal pressure, disc height and compressive stiffness, and examines their mutual relationships. METHODS: Fifteen caprine lumbar discs with 5 mm of vertebral bone on either side were compressed by 1 Hz sinusoidal load for 4.5 h. After preload, 'High' (130 ± 20 N) or 'Low' (50 ± 10 N) loads were alternated every half hour. Continuous intradiscal pressure measurement was performed with a pressure transducer needle. RESULTS: Each disc showed a linear relationship between axial compression and intradiscal pressure (R (2) > 0.91). The intercept of linear regression analysis declined over time, but the gradient remained constant. Disc height changes were correlated to intradiscal pressure changes (R (2) > 0.98): both decreased during High loading, and increased during Low loading. In contrast, compressive stiffness increased during High loading, and was inversely related to intradiscal pressure and disc height. CONCLUSIONS: Intradiscal pressure is influenced by recent loading due to fluid flow. The correlations found in this study suggest that intradiscal pressure is important for disc height and axial compliance. These findings are relevant for mechanobiology studies, nucleus replacements, finite element models, and ex vivo organ culture systems.

Torsion biomechanics of the spine following lumbar laminectomy: a human cadaver study.

PURPOSE: Lumbar laminectomy affects spinal stability in shear loading. However, the effects of laminectomy on torsion biomechanics are unknown. The purpose of this study was to investigate the effect of laminectomy on torsion stiffness and torsion strength of lumbar spinal segments following laminectomy and whether these biomechanical parameters are affected by disc degeneration and bone mineral density (BMD). METHODS: Ten human cadaveric lumbar spines were obtained (age 75.5, range 59-88). Disc degeneration (MRI) and BMD (DXA) were assessed. Disc degeneration was classified according to Pfirrmann and dichotomized in mild or severe. BMD was defined as high BMD (≥median BMD) or low BMD (

Which factors prognosticate rotational instability following lumbar laminectomy?

PURPOSE: Reduced strength and stiffness of lumbar spinal motion segments following laminectomy may lead to instability. Factors that predict shear biomechanical properties of the lumbar spine were previously published. The purpose of the present study was to predict spinal torsion biomechanical properties with and without laminectomy from a total of 21 imaging parameters. METHOD: Radiographs and MRI of ten human cadaveric lumbar spines (mean age 75.5, range 59-88 years) were obtained to quantify geometry and degeneration of the motion segments. Additionally, dual X-ray absorptiometry (DXA) scans were performed to measure bone mineral content and density. Facet-sparing lumbar laminectomy was performed either on L2 or L4. Spinal motion segments were dissected (L2-L3 and L4-L5) and tested in torsion, under 1,600 N axial compression. Torsion moment to failure (TMF), early torsion stiffness (ETS, at 20-40 % TMF) and late torsion stiffness (LTS, at 60-80 % TMF) were determined and bivariate correlations with all parameters were established. For dichotomized parameters, independent-sample t tests were used. RESULTS: Univariate analyses showed that a range of geometric characteristics and disc and bone quality parameters were associated with torsion biomechanical properties of lumbar segments. Multivariate models showed that ETS, LTS and TMF could be predicted for segments without laminectomy (r (2) values 0.693, 0.610 and 0.452, respectively) and with laminectomy (r (2) values 0.952, 0.871 and 0.932, respectively), with DXA-derived measures of bone quality and quantity as the main predictors. CONCLUSIONS: Vertebral bone content and geometry, i.e. intervertebral disc width, frontal area and facet joint tropism, were found to be strong predictors of ETS, LTS and TMF following laminectomy, suggesting that these variables could predict the possible development of post-operative rotational instability following lumbar laminectomy. Proposed diagnostic parameters might aid surgical decision-making when deciding upon the use of instrumentation techniques.

Which factors prognosticate spinal instability following lumbar laminectomy?

PURPOSE: Reduced strength and shear stiffness (SS) of lumbar motion segments following laminectomy may lead to instability. The purpose of the present study was to assess a broad range of parameters as potential predictors of shear biomechanical properties of the lumbar spine. METHODS: Radiographs and MRI of all lumbar spines were obtained to classify geometry and degeneration of the motion segments. Additionally, dual X-ray absorptiometry (DXA) scans were performed to measure bone mineral content and density (BMC and BMD). Facet sparing lumbar laminectomy was performed either on L2 or L4, in 10 human cadaveric lumbar spines (mean age 72.1 years, range 53-89 years). Spinal motion segments were dissected (L2-L3 and L4-L5) and tested in shear, under simultaneously loading with 1600 N axial compression. Shear stiffness, shear yield force (SYF) and shear force to failure (SFF) were determined and statistical correlations with all parameters were established. RESULTS: Following laminectomy, SS, SYF, and SFF declined (by respectively 24, 41, and 44%). For segments with laminectomy, SS was significantly correlated with intervertebral disc degeneration and facet joint degeneration (Pfirrmann: r = 0.64; Griffith: r = 0.70; Lane: r = 0.73 and Pathria: r = 0.64), SYF was correlated with intervertebral disc geometry (r = 0.66 for length; r = 0.66 for surface and r = 0.68 for volume), BMC (r = 0.65) and frontal area (r = 0.75), and SFF was correlated with disc length (r = 0.73) and BMC (r = 0.81). For untreated segments, SS was significantly correlated with facet joint tropism (r = 0.71), SYF was correlated with pedicle geometry (r = 0.83), and SFF was correlated with BMC (r = 0.85), BMD (r = 0.75) and frontal area (r = 0.75). SS, SYF and SFF could be predicted for segments with laminectomy (r (2) values respectively: 0.53, 0.81 and 0.77) and without laminectomy (r (2) value respectively: 0.50, 0.83 and 0.83). CONCLUSIONS: Significant loss of strength and SS are predicted by BMC, BMD, intervertebral disc geometry and degenerative parameters, suggesting that low BMC or BMD, small intervertebral discs and absence of osteophytes could predict the possible development of post-operative instability following lumbar laminectomy.

The impact of bone mineral density and disc degeneration on shear strength and stiffness of the lumbar spine following laminectomy.

PURPOSE: Laminectomy is a standard surgical procedure for elderly patients with symptomatic degenerative lumbar stenosis. The procedure aims at decompression of the affected nerves, but it also causes a reduction of spinal shear strength and shear stiffness. The magnitude of this reduction and the influence of bone mineral density (BMD) and disc degeneration are unknown. We studied the influence of laminectomy, BMD, and disc degeneration on shear force to failure (SFF) and shear stiffness (SS). METHODS: Ten human cadaveric lumbar spines were obtained (mean age 72.1 years, range 53-89 years). Laminectomy was performed either on L2 or L4, equally divided within the group of ten spines. BMD was assessed by dual X-ray absorptiometry (DXA). Low BMD was defined as a BMD value below the median. Intervertebral discs were assessed for degeneration by MRI (Pfirrmann) and scaled in mild and severe degeneration groups. Motion segments L2-L3 and L4-L5 were isolated from each spine. SFF and SS were measured, while loading simultaneously with 1,600 N axial compression. RESULTS: Low BMD had a significant negative effect on SFF. In addition, a significant interaction between low BMD and laminectomy was found. In the high BMD group, SFF was 2,482 N (range 1,678-3,284) and decreased to 1,371 N (range 940-1,886) after laminectomy. In the low BMD group, SFF was 1,339 N (range 909-1,628) and decreased to 761 N (range 561-1,221). Disc degeneration did not affect SFF, nor did it interact with laminectomy. Neither low BMD nor the interaction of low BMD and laminectomy did affect SS. Degeneration and its interaction with laminectomy did not significantly affect SS. CONCLUSIONS: In conclusion, low BMD significantly decreased SFF before and after lumbar laminectomy. Therefore, DXA assessment may be an important asset to preoperative screening. Lumbar disc degeneration did not affect shear properties of lumbar segments before or after laminectomy.

Biomechanical assessment of the effects of decompressive surgery in non-chondrodystrophic and chondrodystrophic canine multisegmented lumbar spines.

PURPOSE: Dogs are often used as an animal model in spinal research, but consideration should be given to the breed used as chondrodystrophic (CD) dog breeds always develop IVD degeneration at an early age, whereas non-chondrodystrophic (NCD) dog breeds may develop IVD degeneration, but only later in life. The aim of this study was to provide a mechanical characterization of the NCD [non-degenerated intervertebral discs (IVDs), rich in notochordal cells] and CD (degenerated IVDs, rich in chondrocyte-like cells) canine spine before and after decompressive surgery (nucleotomy). METHODS: The biomechanical properties of multisegmented lumbar spine specimens (T13-L5 and L5-Cd1) from 2-year-old NCD dogs (healthy) and CD dogs (early degeneration) were investigated in flexion/extension (FE), lateral bending (LB), and axial rotation (AR), in the native state and after nucleotomy of L2-L3 or dorsal laminectomy and nucleotomy of L7-S1. The range of motion (ROM), neutral zone (NZ), and NZ stiffness (NZS) of L1-L2, L2-L3, L6-L7, and L7-S1 were calculated. RESULTS: In native spines in both dog groups, the greatest mobility in FE was found at L7-S1, and the greatest mobility in LB at L2-L3. Surgery significantly increased the ROM and NZ, and significantly decreased the NZS in FE, LB, and AR in both breed groups. However, surgery at L2-L3 resulted in a significantly larger increase in NZ and decrease in NZS in the CD spines compared with the NCD spines, whereas surgery at L7-S1 induced a significantly larger increase in ROM and decrease in NZS in the NCD spines compared with the CD spines. CONCLUSIONS: Spinal biomechanics significantly differ between NCD and CD dogs and researchers should consider this aspect when using the dog as a model for spinal research.

Functional bracing in distal radius fractures: a cadaveric pilot study.

Background: Extra-articular distal radius fractures are often treated by circular casting. A functional brace, however, may equally support the fracture zone but allows early mobilization of the radiocarpal joint. Since the amount of fracture movement for different types of fixation is currently unknown, a study was initiated to investigate the degree of bone displacement in extra-articular distal radius fractures fixated by regular circular casting, functional bracing, or no-fixation. Methods: In four cadaveric arms, an extra-articular distal radius fracture was simulated and immobilized by the three ways of fixation. After creating an extra-articular distal radius fracture, the fracture was reduced anatomically and the cadaveric arm was strapped in a test frame. Hereafter, flexion, extension and deviation of the hand were then induced by a static moment of force of one newton meter. Subsequently CT scans of the wrist were performed and bone displacement was quantified. Results: Immobilization of an extra-articular distal radius fracture by functional bracing provides comparable fixation compared to circular casting and no fixation, and shows significantly less extension-rotation displacement of the distal bone segment for the wrist in flexion and palmodorsal translation and extension-rotation for the wrist in extension. Conclusion: Functional bracing of extra articular distal radius fractures in cadaveric arms provides significant less extension-rotation displacement in flexion and palmodorsal translation and extension-rotation in extension compared to circular casting and no fixation.

An anatomically shaped medial meniscus prosthesis is able to partially restore the contact mechanics of the meniscectomized knee joint.

PURPOSE: The aim of this study was to determine whether a flexible medial meniscus prosthesis is more capable of sharing loads with the direct tibiofemoral cartilage contact than the stiffer first-generation prosthesis. Additionally, the effect of the prosthesis on the tibial pressure distribution after total meniscectomy was investigated. METHODS: In an artificial knee joint, the relative amounts of load transferred through both meniscus prostheses and the direct tibiofemoral contact were assessed with pressure-sensitive sensors. Additionally, six cadaveric knee joints were loaded in a physiological environment. Tibial contact pressures were measured with an intact native meniscus, after total meniscectomy and after implantation of the second-generation meniscus prosthesis. RESULTS: Whereas the first generation of the meniscus prosthesis transferred virtually all the load from femur to tibia, the second-generation prosthesis allowed for load sharing with the direct tibiofemoral contact. No differences in load sharing were found between the native meniscus and the second-generation meniscus prosthesis. The prosthesis decreased peak and mean pressures on the medial tibial cartilage compared to meniscectomy. No significant differences in pressure were found between the native meniscus and the meniscus prosthesis. CONCLUSIONS: The second-generation meniscus prosthesis presented in this study can share loads with the direct tibiofemoral contact, a characteristic that the first-generation prosthesis did not have. The flexible meniscus prosthesis significantly reduces the contact pressures on the medial tibial plateau after total meniscectomy. Although the biomechanical performance of the native meniscus could not be reproduced completely, the meniscus prosthesis may have the potential to relieve post-meniscectomy pain symptoms.

Quantifying intervertebral disc mechanics: a new definition of the neutral zone.

BACKGROUND: The neutral zone (NZ) is the range over which a spinal motion segment (SMS) moves with minimal resistance. Clear as this may seem, the various methods to quantify NZ described in the literature depend on rather arbitrary criteria. Here we present a stricter, more objective definition. METHODS: To mathematically represent load-deflection of a SMS, the asymmetric curve was fitted by a summed sigmoid function. The first derivative of this curve represents the SMS compliance and the region with the highest compliance (minimal stiffness) is the NZ. To determine the boundaries of this region, the inflection points of compliance can be used as unique points. These are defined by the maximum and the minimum in the second derivative of the fitted curve, respectively. The merits of the model were investigated experimentally: eight porcine lumbar SMS's were bent in flexion-extension, before and after seven hours of axial compression. RESULTS: The summed sigmoid function provided an excellent fit to the measured data (r2 > 0.976). The NZ by the new definition was on average 2.4 (range 0.82-7.4) times the NZ as determined by the more commonly used angulation difference at zero loading. Interestingly, NZ consistently and significantly decreased after seven hours of axial compression when determined by the new definition. On the other hand, NZ increased when defined as angulation difference, probably reflecting the increase of hysteresis. The methods thus address different aspects of the load-deflection curve. CONCLUSIONS: A strict mathematical definition of the NZ is proposed, based on the compliance of the SMS. This operational definition is objective, conceptually correct, and does not depend on arbitrarily chosen criteria.

Mechanical stress regulates bone regulatory gene expression independent of estrogen and vitamin D deficiency in rats.

Mechanical stress determines bone mass and structure. It is not known whether mechanical loading affects expression of bone regulatory genes in a combined deficiency of estrogen and vitamin D. We studied the effect of mechanical loading on the messenger RNA (mRNA) expression of bone regulatory genes during vitamin D and/or estrogen deficiency. We performed a single bout in vivo axial loading with 14 N peak load, 2 Hz frequency and 360 cycles in right ulnae of nineteen weeks old female control Wistar rats with or without ovariectomy (OVX), vitamin D deficiency and the combination of OVX and vitamin D deficiency (N = 10/group). Total bone RNA was isolated 6 hours after loading, and mRNA expression was detected of Mepe, Fgf23, Dmp1, Phex, Sost, Col1a1, Cyp27b1, Vdr, and Esr1. Serum levels of 25(OH)D, 1,25(OH)2 D and estradiol were also measured at this time point. The effect of loading, vitamin D and estrogen deficiency and their interaction on bone gene expression was tested using a mixed effect model analysis. Mechanical loading significantly increased the mRNA expression of Mepe, and Sost, whereas it decreased the mRNA expression of Fgf23 and Esr1. Mechanical loading showed a significant interaction with vitamin D deficiency with regard to mRNA expression of Vdr and Esr1. Mechanical loading affected gene expression of Mepe, Fgf23, Sost, and Esr1 independently of vitamin D or estrogen, indicating that mechanical loading may affect bone turnover even during vitamin D deficiency and after menopause.

Anterior shear strength of the porcine lumbar spine after laminectomy and partial facetectomy.

Degenerative lumbar spinal stenosis is the most common reason for lumbar surgery in patients in the age of 65 years and older. The standard surgical management is decompression of the spinal canal by laminectomy and partial facetectomy. The effect of this procedure on the shear strength of the spine has not yet been investigated in vitro. In the present study we determined the ultimate shear force to failure, the displacement and the shear stiffness after performing a laminectomy and a partial facetectomy. Eight lumbar spines of domestic pigs (7 months old) were sectioned to obtain eight L2-L3 and eight L4-L5 motion segments. All segments were loaded with a compression force of 1,600 N. In half of the 16 motion segments a laminectomy and a 50% partial facetectomy were applied. The median ultimate shear force to failure with laminectomy and partial facetectomy was 1,645 N (range 1,066-1,985) which was significantly smaller (p = 0.012) than the ultimate shear force to failure of the control segments (median 2,113, range 1,338-2,659). The median shear stiffness was 197.4 N/mm (range 119.2-216.7) with laminectomy and partial facetectomy which was significantly (p = 0.036) smaller than the stiffness of the control specimens (median 216.5, 188.1-250.2). It was concluded that laminectomy and partial facetectomy resulted in 22% reduction in ultimate shear force to failure and 9% reduction in shear stiffness. Although relatively small, these effects may explain why patients have an increased risk of sustaining shear force related vertebral fractures after spinal decompression surgery.

Biomechanical and in vivo evaluation of experimental closure devices of the annulus fibrosus designed for a goat nucleus replacement model.

Promising strategies are being developed to replace or regenerate the herniated nucleus pulposus. However, clinical efficacy of these methods has still to be addressed, and the lack of appropriate annulus closure techniques is increasingly being recognised as a major limiting factor. In the current study, in vitro and in vivo evaluation of novel annulus closure devices (ACDs) was performed. These devices are intended to be used in adjunct to nucleus replacement therapies in an experimental goat study. After a standardised discectomy had been performed, different ACDs were implanted solely or in addition to a collagen nucleus replacement implant. Biomechanical effects and axial failure load were assessed in vitro and followed by in vivo evaluation in a goat model. On axial compression, the average axial failure load for ACDs with four barb rings was significantly higher compared to the implants with five barb rings. The increased range of flexion-extension and latero-flexion observed after discectomy were restored to the normal range after implantation of the implants. Positive findings with the four-ring ACD were confirmed in goats after a follow-up of 2 weeks in vivo. However, after 6 weeks most implants (n = 16) showed signs of destruction and displacement. Although there seemed to be a tendency towards better results when ACDs were placed in addition to the nucleus replacements, these differences were not statistically significant. Moreover, two endplate reactions extending into the subchondral bone were observed, most likely due to continuous friction between the ACD and the vertebrae. Although current results are encouraging first steps towards the development of an efficient ACD for animal models, further optimisation is necessary. Current results also show that one cannot rely on in vitro biomechanical studies with annulus closure techniques, and these should always be confirmed in vivo in a large animal model.

Biomechanical properties in motion of lumbar spines with degenerative scoliosis.

Degenerative lumbar scoliosis presumably alters spinal biomechanics, but a lack of quantitative reference measurements of these spines exists. We aimed to assess the biomechanical properties of spines with degenerative scoliosis, and to relate these to intervertebral disc degeneration (DD) and Cobb angle. Secondly, we compared these results to previous measurements of non-scoliotic spines. Ten cadaveric spines (Th12-L5, mean age 82 ±â€¯11 years) with Cobb angle ≥10° and apex at L3 were acquired. Three loading cycles (-4 to 4 Nm) were applied in flexion/extension (FE), lateral bending (LB), and axial rotation (AR). The range of motion (ROM), neutral zone (NZ) stiffness, NZ ROM, elastic zone (EZ) stiffness and hysteresis were calculated for each motion segment in the loading direction. ROM was calculated in coupled directions, expressed as a percentage of rotation in the loaded direction. For Th12-L5, there was a ROM (degrees ±â€¯SD) of 14.9 ±â€¯6.5 in FE, 14.9 ±â€¯7.8 in LB, and 10.2 ±â€¯5.5 in AR. The median (Nm/degree (Q1;Q3)) NZs was 0.24 (0.19;0.35) in FE, 0.25 (0.22;0.42) in LB, and 0.49 (0.33;0.99) in AR. Greater coupled motions related to higher Cobb angle, especially during AR on segments around the apex (FE: ρ = 0.539, p = 0.021 and LB: ρ = 0.821, p = 0.000). DD correlated to lower ROM and increased NZs on L2-L3 in FE (ρ = -0.721, p = 0.028 and ρ = 0.694, p = 0.038, respectively). Compared to non-scoliotic spines, smaller ROM in FE (p = 0.030) was found. This study describes the biomechanical properties of lumbar spines with degenerative scoliosis. Compared to non-scoliotic spines, they tended to be stiffer and exhibited smaller ROM in FE. DD only affected the ROM and NZs of the segments around the apex.

In Vivo Models of Mechanical Loading.

The skeleton fulfils its mechanical functions through structural organization and material properties of individual bones. It is stated that both cortical and trabecular morphology and mass can be (re)modelled in response to changes in mechanical strains engendered by load-bearing. To address this, animal models that enable the application of specific loads to individual bones have been developed. These are useful in defining how loading modulates (re)modeling and allow examination of the mechanisms that coordinate these events. This chapter describes how to apply mechanical loading to murine bones through points of articulation, which allows changes in endosteal, periosteal as well as trabecular bone to be revealed at multiple hierarchies, by a host of methodologies, including double fluorochrome labeling and computed tomography.

Comparison of polyetheretherketone versus silicon nitride intervertebral spinal spacers in a caprine model.

Polyetheretherketone (PEEK) is commonly used as a spinal spacer for intervertebral fusion surgery. Unfortunately, PEEK is bioinert and does not effectively osseointegrate into living bone. In contrast, comparable spacers made of silicon nitride (Si3 N4 ) possess a surface nanostructure and chemistry that encourage appositional bone healing. This observational study was designed to compare the outcomes of these two biomaterials when implanted as spacers in an adult caprine model. Lumbar interbody fusion surgeries were performed at two adjacent levels in eight adult goats using implants of PEEK and Si3 N4 . At six-months after surgery, the operative and adjacent spinal segments were extracted and measured for bone fusion, bone volume, bone-implant contact (BIC) and soft-tissue implant contact (SIC) ratios, and biodynamic stability. The null hypothesis was that no differences in these parameters would be apparent between the two groups. Fusion was observed in seven of eight implants in each group with greater bone formation in the Si3 N4 group (52.6%) versus PEEK (27.9%; p = 0.2). There were no significant differences in BIC ratios between PEEK and Si3 N4 , and the biodynamic stability of the two groups was also comparable. The results suggest that Si3 N4 spacers are not inferior to PEEK and they may be more effective in promoting arthrodesis. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 00B: 000-000, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 688-699, 2019.

Contribution of vertebral [corrected] bodies, endplates, and intervertebral discs to the compression creep of spinal motion segments.

Spinal segments show non-linear behavior under axial compression. It is unclear to what extent this behavior is attributable to the different components of the segment. In this study, we quantified the separate contributions of vertebral bodies and intervertebral discs to creep of a segment. Secondly, we investigated the contribution of bone and osteochondral endplate (endplates including cartilage) to the deformation of the vertebral body. From eight porcine spines a motion segment, a disc and a vertebral body were dissected and subjected to mechanical testing. In an additional test, cylindrical samples, machined from the lowest thoracic vertebrae of 11 porcine spines, were used to compare the deformation of vertebral bone and endplate. All specimens were subjected to three loading cycles, each comprising a loading phase (2.0 MPa, 15 min) and a recovery phase (0.001 MPa, 30 min). All specimens displayed substantial time-dependent height changes. Average creep was the largest in motion segments and smallest in vertebral bodies. Bone samples with endplates displayed substantially more creep than samples without. In the early phase, behavior of the vertebra was similar to that of the disc. Visco-elastic deformation of the endplate therefore appeared dominant. In the late creep phase, behavior of the segment was similar to that of isolated discs, suggesting that in this phase the disc dominated creep behavior, possibly by fluid flow from the nucleus. We conclude that creep deformation of vertebral bodies contributes substantially to creep of motion segments and that within a vertebral body endplates play a major role.

Effect of long-term preservation on the mechanical properties of cortical bone in goats.

BACKGROUND AND PURPOSE: Bones used in mechanical studies are frequently harvested from human cadavers that have been embalmed in a buffered formaldehyde solution. It has been reported that formaldehyde fixation or freezing hardly affects the mechanical properties of bone after a storage period of several weeks. However, human cadaver bones are usually stored for longer periods of time before use. We therefore investigated the effects of long-term embalming or freezing on the mechanical properties of cortical bone. METHODS: After 5 different storage periods (ranging from 0 to 12 months), goat femora and humeri were used to evaluate the effect of embalming and freezing on torsion, and on bending stiffness and strength. The effect on hardness and bone mineral density (BMD) was also evaluated. RESULTS: Even after 1 year, no statistically significant differences could be found in stiffness, strength, and energy absorption when we compared embalmed or frozen bones to a fresh reference group. In addition, although we found no significant change in BMD, there appears to be a tendency to increasing hardness. INTERPRETATION: We found that there was no effect on the mechanical properties of bone after storage periods of 1 year. We conclude that embalmed or frozen bones can safely be used for mechanical testing, at least for storage periods of up to one year.