RESUMEN
The fine regulation of catalysts by the atomic-level removal of inactive atoms can promote the active site exposure for performance enhancement, whereas suffering from the difficulty in controllably removing atoms using current micro/nano-scale material fabrication technologies. Here, we developed a surface atom knockout method to promote the active site exposure in an alloy catalyst. Taking Cu3Pd alloy as an example, it refers to assemble a battery using Cu3Pd and Zn as cathode and anode, the charge process of which proceeds at about 1.1 V, equal to the theoretical potential difference between Cu2+/Cu and Zn2+/Zn, suggesting the electricity-driven dissolution of Cu atoms. The precise knockout of Cu atoms is confirmed by the linear relationship between the amount of the removed Cu atoms and the battery cumulative specific capacity, which is attributed to the inherent atom-electron-capacity correspondence. We observed the surface atom knockout process at different stages and studied the evolution of the chemical environment. The alloy catalyst achieves a higher current density for oxygen reduction reaction compared to the original alloy and Pt/C. This work provides an atomic fabrication method for material synthesis and regulation toward the wide applications in catalysis, energy, and others.
RESUMEN
Metal-air secondary batteries with ultrahigh specific energies have received vast attention and are considered new promising energy storage. The slow redox reactions between oxygen-water molecules lead to low energy efficiency (55-71%) and limited applications. Herein, it is proposed that the MIL-68(In)-derived porous carbon nanotube supports the CoNiFeP heteroconjugated alloy catalyst with an overboiling point electrolyte to achieve the ultrahigh oxidation rate of water molecules. Structural characterization and density functional theory calculations reveal that the new catalyst greatly reduces the free energy of the process, and the overboiling point further accelerates the dissociation of OâH and hydrogen bonds, and the release of O2 molecules, achieving an extra-low overpotential of 110 mV@10 mA cm-2 far lower than commercial Ir/C catalysts of 192 mV at 125 °C and state-of-the-art. Furthermore, the energy efficiency of assembled rechargeable zinc-air batteries begins to break through at 85 °C, jumps at 100 °C, and reaches ultrahigh energy efficiency of 88.1% at 125 °C with an ultralow decay rate of 0.0068% after 150 cycles far superior to those of reported metal-air batteries. This work provides a new catalyst and electrolyte joint-design strategy and reexamines the battery operating temperature to construct higher energy efficiency for secondary fuel cells.
RESUMEN
(In, Ga) alloy droplets are used to catalyse the growth of (In, Ga)As nanowires by molecular beam epitaxy on Si(111) substrates. The composition, morphology and optical properties of these nanowires can be tuned by the employed elemental fluxes. To incorporate more than 10% of In, a high In/(In+Ga) flux ratio above 0.7 is required. We report a maximum In content of almost 30% in bulk (In, Ga)As nanowires for an In/(In+Ga) flux ratio of 0.8. However, with increasing In/(In+Ga) flux ratio, the nanowire length and diameter are notably reduced. Using photoluminescence and cathodoluminescence spectroscopy on nanowires covered by a passivating (In, Al)As shell, two luminescence bands are observed. A significant segment of the nanowires shows homogeneous emission, with a wavelength corresponding to the In content in this segment, while the consumption of the catalyst droplet leads to a spectrally-shifted emission band at the top of the nanowires. The (In,Ga)As nanowires studied in this work provide a new approach for the integration of infrared emitters on Si platforms.
RESUMEN
Electrooxidation of biomass-derived glycerol which is regarded as a main byproduct of industrial biodiesel production, is an innovative strategy to produce value-added chemicals, but currently showcases slow kinetics, limited Faraday efficiency, and unclear catalytic mechanism. Herein, we report high-efficiency electrooxidation of glycerol into formate via a Cu doped NiCo alloy catalyst supported on nickel foam (Cu-NiCo/NF) in a coupled system paired with nitrate reduction. The designed Cu-NiCo/NF delivers only 1.23 V vs. RHE at 10 mA cm-2, and a record Faraday efficiency of formate of 93.8%. The superior performance is ascribed to the rapid generation of NiIII-OOH and CoIII-OOH and favorable coupling of surface *O with reactive intermediates. Using Cu-NiCo/NF as a bifunctional catalyst, the coupled system synchronously produces NH3 and formate, showing 290 mV lower than the coupling of hydrogen evolution reaction, together with excellent long-term stability for up to 144 h. This work lays out new guidelines and reliable strategies from catalyst design to system coupling for biomass-derived electrochemical refinery.
RESUMEN
The development of efficient, stable, and low-cost bifunctional catalysts for the hydrogen evolution/oxidation reaction (HER/HOR) is critical to promote the application of hydrogen gas batteries in large scale energy storage systems. Here we demonstrate a non-noble metal high-entropy alloy grown on Cu foam (NNM-HEA@CF) as a self-supported catalytic electrode for nickel-hydrogen gas (Ni-H2) batteries. Experimental and theoretical calculation results reveal that the NNM-HEA catalyst greatly facilitates the HER/HOR catalytic process through the optimized electronic structures of the active sites. The assembled Ni-H2 battery with NNM-HEA@CF as the anode shows excellent rate capability and exceptional cycling performance of over 1800 h without capacity decay at an areal capacity of 15 mAh cm-2. Furthermore, a scaled-up Ni-H2 battery fabricated with an extended capacity of 0.45 Ah exhibits a high cell-level energy density of â¼109.3 Wh kg-1. Moreover, its estimated cost reaches as low as â¼107.8 $ kWh-1 based on all key components of electrodes, separator and electrolyte, which is reduced by more than 6 times compared to that of the commercial Pt/C-based Ni-H2 battery. This work provides an approach to develop high-efficiency non-noble metal-based bifunctional catalysts for hydrogen batteries in large-scale energy storage applications.
RESUMEN
Alloys with bimetallic electron modulation effect are promising catalysts for the electrooxidation of urea. However, the side reaction oxygen evolution reaction (OER) originating from the competitive adsorption of OH- and urea severely limited the urea oxidation reaction (UOR) activity on the alloy catalysts. This work successfully constructs the defect-rich NiCo alloy with lattice strain (PMo-NiCo/NF) by rapid pyrolysis and co-doping. By taking advantage of the compressive strain, the d-band center of NiCo is shifted downward, inhibiting OH- from adsorbing on the NiCo site and avoiding the detrimental OER. Meanwhile, the oxygenophilic P/Mo tailored specific adsorption sites to adsorb OH- preferentially, which further released the NiCo sites to ensure the enriched adsorption of urea, thus improving the UOR efficiency. As a result, PMo-NiCo/NF only requires 1.27 V and -57 mV to drive a current density of ±10 mA cm-2 for UOR and hydrogen evolution reaction (HER), respectively. With the guidance of this work, reactant competing adsorption sites could be tailored for effective electrocatalytic performance.
RESUMEN
The ideal interface design between the metal and substrate is crucial in determining the overall performance of the alkyne semihydrogenation reaction. Single-atom alloys (SAAs) with isolated dispersed active centers are ideal media for the study of reaction effects. Herein, a charge-asymmetry "armor" SAA (named Pd1Fe SAA@PC), which consists of a Pd1Fe alloy core and a semiconducting P-doped C (PC) shell, is rationally designed as an ideal catalyst for the selective hydrogenation of alkynes with high efficiency. Multiple spectroscopic analyses and density functional theory calculations have demonstrated that Pd1Fe SAA@PC is dual-regulated by lattice tensile and Schottky effects, which govern the selectivity and activity of hydrogenation, respectively. (1) The PC shell layer applied an external traction force causing a 1.2% tensile strain inside the Pd1Fe alloy to increase the reaction selectivity. (2) P doping into the C-shell layer realized a transition from a p-type semiconductor to an n-type semiconductor, thereby forming a unique Schottky junction for advancing alkyne semihydrogenation activity. The dual regulation of lattice strain and the Schottky effect ensures the excellent performance of Pd1Fe SAA@PC in the semihydrogenation reaction of phenylethylene, achieving a conversion rate of 99.9% and a selectivity of 98.9% at 4 min. These well-defined interface modulation strategies offer a practical approach for the rational design and performance optimization of semihydrogenation catalysts.