Conformal sulfidation of HKUST-1 for constructing porous Cu2S/CuO octahedrons realizing highly sensitive non-enzymatic glucose detection.

Metal-organic frameworks (MOFs) are believed to be promising precursors for constructing novel and efficient catalysts for glucose sensing. Herein, HKUST-1 precursors are first fabricated using a one-pot hydrothermal approach, and then HKUST-1 is converted into porous Cu2S/CuO octahedrons through conformal sulfidation with the help of OH-ions. The as-obtained Cu2S/CuO composite can provide rich electrochemical active sites and promoted electric transfer kinetics. Benefiting from these combined merits, the as-fabricated Cu2S/CuO composite is confirmed to be a high-performance catalyst, with high sensitivities of 8269.45 and 4140.82µA mM-1cm-2in the corresponding ranges of 0.05 ∼ 0.6 mM and 0.6 ∼ 1.2 mM, respectively. Moreover, the as-prepared electrode materials possess good anti-interference ability, reproducibility and long-term stability. This work opens up new avenues for the design and preparation of transition metal sulfide composites.

Cu/Cu2O/C nanoparticles and MXene based composite for non-enzymatic glucose sensors.

Copper/Cuprous oxide/Carbon nanoparticles decorated MXene composite was prepared and subsequently examined for its potential application as a non-enzymatic glucose sensor. To carry out this, initially the Cu MOF/MXene composite was synthesised by the hydrothermal method and was annealed in an unreacted environment at different time intervals. During this process, petal like Cu MOF on MXene loses the organic ligands to form a Cu/Cu2O/C based nanoparticles on MXene. Further, an electrode was fabricated with the developed material for understanding the sensing performance by cyclic voltammetry and chronoamperometry in 0.1 M NaOH solution. Results reveal that the highest weight percentage of copper oxide in the composite (15 min of annealed material) shows a higher electro catalytic activity for sensing glucose molecules due to more active sites with good electron transfer ability in the composite. The formed composite exhibits a wide linear range of 0.001-26.5 mM, with a sensitivity of 762.53µAmM-1cm-2(0.001-10.1 mM), and 397.18µAmM-1cm-2(11.2-26.9 mM) and the limit of detection was 0.103µM. In addition to this, the prepared electrode shows a good reusability, repeatability, selectivity with other interferences, stability (93.65% after 30 days of storage), and feasibility of measuring glucose in real samples. This finding reveals that the metal oxide derived from MOF based nanoparticle on the MXene surface will promote the use of non-enzymatic glucose sensors.

Tailoring the d-band center on Ru1Cu single-atom alloy nanotubes for boosting electrochemical non-enzymatic glucose sensing.

The development of cost-effective and highly efficient electrocatalysts is critical to help electrochemical non-enzymatic sensors achieve high performance. Here, a new class of catalyst, Ru single atoms confined on Cu nanotubes as a single-atom alloy (Ru1Cu NTs), with a unique electronic structure and property, was developed to construct a novel electrochemical non-enzymatic glucose sensor for the first time. The Ru1Cu NTs with a diameter of about 24.0 nm showed a much lower oxidation potential (0.38 V) and 9.0-fold higher response (66.5 µA) current than Cu nanowires (Cu NWs, oxidation potential 0.47 V and current 7.4 µA) for glucose electrocatalysis. Moreover, as an electrochemical non-enzymatic glucose sensor, Ru1Cu NTs not only exhibited twofold higher sensitivity (54.9 µA mM-1 cm-2) and wider linear range (0.5-8 mM) than Cu NWs, but also showed a low detection limit (5.0 µM), excellent selectivity, and great stability. According to theoretical calculation results, the outstanding catalytic and sensing performance of Ru1Cu NTs could be ascribed to the upshift of the d-band center that helped promote glucose adsorption. This work presents a new avenue for developing highly active catalysts for electrochemical non-enzymatic sensors.

Iridium oxide-based non-enzymatic glucose sensor: Superior electro-catalytic performance in biological environmental media.

Nanostructured inorganic materials have potential advantages as glucose-sensing elements in diabetes care, thereby circumventing the need for expensive enzymatic agents. However, many nonenzymatic sensors face challenges related to selectivity and reliability, reducing their efficacy in body fluids. In this study, we introduce an Iridium oxide (IrO2)-based non-enzymatic glucose sensor. This sensor demonstrates exceptional electro-catalytic properties in human serum, characterized by high sensitivity (638 µA µM-1cm2) and a consistent recovery rate (∼104%) across 15 cycles in saline. Furthermore, its impressive performance in human serum, as evidenced by a low relative standard deviation (RSD <1.57%), underscores its applicability in biological matrices such as interstitial fluids. Overall, the IrO2 sensor is a promising, highly reversible, economical, and simple method for detecting glucose in continuous monitoring systems.

Nickel foam-loaded Co-MOF@TiO2/MoS2 as electrode materials for dual-function devices for glucose detection and hydrogen evolution.

Dual-functional nanomaterial electrodes have the capability to satisfy the requirements for both sweat analysis and the hydrogen evolution reaction (HER), thereby enabling the integration of electrochemical sensing and hydrogen production. In this study, ZIF-67 cubes are synthesized on nickel foam (NF), while TiO2 is obtained through an annealing process. Subsequently, the ZIF-67@TiO2/MoS2 nanocomposite is fabricated on nickel foam via a hydrothermal method. This composite material exhibits exceptional photocatalytic properties and is also suitable for the detection of glucose in sweat. The glucose detection range spans from 10 nM to 10 mM with a sensitivity of 7.24 µA mM-1 cm-2 for a signal-to-noise ratio of 3 and a detection limit of 0.43 µM. Moreover, when utilized as a hydrogen evolution electrode, this material demonstrates a current density of 10 mA cm-2 at an overpotential of 118 mV, with a Tafel slope of 73 mV/dec. The synthesis process is both straightforward and economical. This research introduces a novel concept for the design of multifunctional chemical sensors.

In situ anchored ternary hierarchical hybrid nickel@cobaltous sulfide on poly(3,4-ethylenedioxythiophene)-reduced graphene oxide for highly efficient non-enzymatic glucose sensing.

A ternary hierarchical hybrid Ni@CoxSy/poly(3,4-ethylenedioxythiophene)-reduced graphene oxide (Ni@CoxSy/PEDOT-rGO) is rationally designed and in situ facilely synthesized as electrocatalyst to construct a binder-free sensing platform for non-enzymatic glucose monitoring through traditional electrodeposition procedure. The as-prepared Ni@CoxSy/PEDOT-rGO presents unique hierarchical structure and multiple valence states as well as strong and robust adhesion between Ni@CoxSy/PEDOT-rGO and GCE. Profiting from the aforementioned merits, the sensing platform constructed under optimal conditions achieved a wide detection range (0.2 µM ~ 2.0 mM) with high sensitivity (1546.32 µA cm-2 mM-1), a rapid response time (5 s), an ultralow detection limit (0.094 µM), superior anti-interference performance, excellent reproducibility and considerable stability. Furthermore, the sensor demonstrates an acceptable accuracy and appreciable recoveries ranging from 90.0 to 102.0% with less than 3.98% RSD in human blood serum samples, indicating the prospect of the sensor for the real samples analysis. It will provide a strategy to rationally design and fabricate ternary hierarchical hybrid as nanozyme for glucose assay.

Zirconium copper oxide microflowers based non-enzymatic screen-printed electrochemical sensor for the detection of glucose in saliva, urine, and blood serum.

Zirconium copper oxide microflowers (Zr/CuO MF) based non-enzymatic sensor was developed for glucose detection in saliva, urine, and blood. An easy urea hydrolysis method was employed for the synthesis of the metal oxide and further calcined to improve the catalytic property. The flower-like morphology of the Zr/CuO was confirmed by SEM analysis and the presence of copper and zirconium was examined using energy dispersive X-ray analysis (EDAX). The Zr/CuO MF modified screen-printed electrodes exhibited excellent glucose sensing performance in 0.15 M NaOH medium and could quantify glucose in the range from 10 µM to 27 mM. A high sensitivity of 1.815 ± 0.003 mA mM-1 cm-2 was obtained for lower glucose concentration from 15 µM to 3 mM and 1.250 ± 0.006 mA mM-1 cm-2 for higher concentration glucose from 3 to 27 mM. The limit of detection of the fabricated sensor was found to be 0.8 µM. The sensor displayed high selectivity and stability towards glucose in different body fluids like saliva, urine, and blood serum at a working potential of 0.6 V (vs. Ag/AgCl). In saliva, urine, and serum samples, the sensor exhibited excellent recovery of 95-108, 92-108, and 93-101% in saliva, urine, and serum, respectively, with a relative standard deviation of less than 10%, demonstrating high accuracy and reliability of the sensor. The developed sensor is promising for developing an invasive and non-invasive point-of-care testing device for glucose detection.

Fabrications of the Flexible Non-Enzymatic Glucose Sensors Using Au-CuO-rGO and Au-CuO-rGO-MWCNTs Nanocomposites as Carriers.

A flexible, non-enzymatic glucose sensor was developed and tested on a polyethylene terephthalate (PET) substrate. The sensor's design involved printing Ag (silver) as the electrode and utilizing mixtures of either gold-copper oxide-modified reduced graphene oxide (Au-CuO-rGO) or gold-copper oxide-modified reduced graphene oxide-multi-walled carbon nanotubes (Au-CuO-rGO-MWCNTs) as the carrier materials. A one-pot synthesis method was employed to create a nanocomposite material, consisting of Au-CuO-rGO mixtures, which was then printed onto pre-prepared flexible electrodes. The impact of different weight ratios of MWCNTs (0~75 wt%) as a substitute for rGO was also investigated on the sensing characteristics of Au-CuO-rGO-MWCNTs glucose sensors. The fabricated electrodes underwent various material analyses, and their sensing properties for glucose in a glucose solution were measured using linear sweep voltammetry (LSV). The LSV measurement results showed that increasing the proportion of MWCNTs improved the sensor's sensitivity for detecting low concentrations of glucose. However, it also led to a significant decrease in the upper detection limit for high-glucose concentrations. Remarkably, the research findings revealed that the electrode containing 60 wt% MWCNTs demonstrated excellent sensitivity and stability in detecting low concentrations of glucose. At the lowest concentration of 0.1 µM glucose, the nanocomposites with 75 wt% MWCNTs showed the highest oxidation peak current, approximately 5.9 µA. On the other hand, the electrode without addition of MWCNTs displayed the highest detection limit (approximately 1 mM) and an oxidation peak current of about 8.1 µA at 1 mM of glucose concentration.

Quasi-aligned Cu2S/Cu(OH)2nanorod arrays anchored on Cu foam as self-supported electrode for non-enzymatic glucose detection.

Self-supported Cu2S/Cu(OH)2composite nanorods for highly sensitive non-enzymatic glucose sensing werein situgrown on Cu foam by simple hydrothermal treatment of aligned Cu(OH)2nanorods. The physicochemical and electrochemical properties of the as-fabricated Cu2S/Cu(OH)2composite nanorods were characterized by scanning electron microscopy, transmission electron microscopy, x-ray diffraction, Raman spectroscope, x-ray photoelectron spectroscope, cyclic voltammetry, electrochemical impedance spectroscopy, amperometrici-tmeasurements. The mechanism of the composite nanorods produced on conductive substrates was also explored. The electrode exhibits a sensitivity of 9626.88µA mM-1cm-2towards glucose with good anti-interference ability, indicating it a promising electrode material for the enhanced non-enzymatic glucose detection.

Ti2C-TiO2 MXene Nanocomposite-Based High-Efficiency Non-Enzymatic Glucose Sensing Platform for Diabetes Monitoring.

Diabetes is a major health challenge, and it is linked to a number of serious health issues, including cardiovascular disease (heart attack and stroke), diabetic nephropathy (kidney damage or failure), and birth defects. The detection of glucose has a direct and significant clinical importance in the management of diabetes. Herein, we demonstrate the application of in-situ synthesized Ti2C-TiO2 MXene nanocomposite for high throughput non-enzymatic electrochemical sensing of glucose. The nanocomposite was synthesized by controlled oxidation of Ti2C-MXene nanosheets using H2O2 at room temperature. The oxidation results in the opening up of Ti2C-MXene nanosheets and the formation of TiO2 nanocrystals on their surfaces as revealed in microscopic and spectroscopic analysis. Nanocomposite exhibited considerably high electrochemical response than parent Ti2C MXene, and hence utilized as a novel electrode material for enzyme-free sensitive and specific detection of glucose. Developed nanocomposite-based non-enzymatic glucose sensor (NEGS) displays a wide linearity range (0.1 µM-200 µM, R2 = 0.992), high sensitivity of 75.32 µA mM-1 cm-2, a low limit of detection (0.12 µM) and a rapid response time (~3s). NEGS has further shown a high level of repeatability and selectivity for glucose in serum spiked samples. The unveiled excellent sensing performance of NEGS is credited to synergistically improved electrochemical response of Ti2C MXene and TiO2 nanoparticles. All of these attributes highlight the potential of MXene nanocomposite as a next-generation NEGS for on the spot mass screening of diabetic patients.

Ni-Coated Diamond-like Carbon-Modified TiO2 Nanotube Composite Electrode for Electrocatalytic Glucose Oxidation.

In this paper, a Ni and diamond-like carbon (DLC)-modified TiO2 nanotube composite electrode was prepared as a glucose sensor using a combination of an anodizing process, electrodeposition, and magnetron sputtering. The composition and morphology of the electrodes were analyzed by a scanning electron microscope and energy dispersive X-ray detector, and the electrochemical glucose oxidation performance of the electrodes was evaluated by cyclic voltammetry and chronoamperometry. The results show that the Ni-coated DLC-modified TiO2 electrode has better electrocatalytic oxidation performance for glucose than pure TiO2 and electrodeposited Ni on a TiO2 electrode, which can be attributed to the synergistic effect between Ni and carbon. The glucose test results indicate a good linear correlation in a glucose concentration range of 0.99-22.97 mM, with a sensitivity of 1063.78 µA·mM-1·cm-2 and a detection limit of 0.53 µM. The results suggest that the obtained Ni-DLC/TiO2 electrode has great application potential in the field of non-enzymatic glucose sensors.

A novel non-enzymatic glucose electrochemical sensor with high sensitivity and selectivity based on CdIn2O4nanoparticles on 3D Ni foam substrate.

Due to the poor conductivity of Fe based, Cu based and Co based electrode materials commonly used in the electrochemical detection of glucose, and the uneven stirring and poor conductivity of the traditional preparation method based on glassy carbon electrode. In order to solve the above problems, in this work, CdIn2O4with high electrical conductivity was directly grown on three-dimensional (3D) Ni foam to prepare electrode materials for non-enzymatic glucose sensors. CdIn2O4nanoparticles is prepared from cadmium acetate and indium nitrate hydrate in benzyl alcohol by non-aqueous sol-gel method. The electrocatalytic oxidation performances of CdIn2O4electrode material for non-enzymatic glucose are studied. The results show that the proposed CdIn2O4electrode material has good electrochemical properties and sensing performance for glucose detection. The electrochemical response of CdIn2O4electrode material to glucose is recorded that calibration plot for glucose concentrations ranging from 1.0µM to 1.0 mM (R2 = 0.99), a limit detection of 0.08µM, an excellent sensitivity of 3.2925 mA.mM-1.cm-2, a rapid response time of 1.58 s, a good selectivity and a good long-term stability. These demonstrate the significant potential of CdIn2O4electrode material based on 3D Ni foam as non-enzymatic glucose sensors, which makes it possible to use it as a practical glucose detector. This work could introduce a new concept of nanoparticles modified electrode material grown directly on 3D Ni foam, thus a simple and reliable electrochemical glucose sensor platform is realized. This study was completed in 2019 in the school of materials and energy, Yunnan University.

Nickel sulfide nanoworm network architecture as a binder-free high-performance non-enzymatic glucose sensor.

Nickel sulfide nanoworm (Ni3S2 NW) network architecture was directly grown on the poly (3,4-ethylenedioxythiophene)-reduced graphene oxide hybrid films (PEDOT-rGO HFs) modified on glassy carbon electrode (GCE), acting as a binder-free sensor for high-performance non-enzymatic glucose monitoring. The sensor exhibited the satisfactory sensitivity (2123 µA mM-1 cm-2), wide linear range (15~9105 µM), low detection limit (0.48 µM), and rapid response time (< 1.5 s) at a potential of 0.5 V (vs. SCE) in 0.1 M NaOH and possessed good selectivity, reproducibility, and stability. The enhanced electrocatalytic activity of the sensor towards glucose oxidation was attributed to the particular morphology, satisfying hydrophilic nature, strong combination between Ni3S2 NWs, PEDOT-rGO, and bare GCE. Moreover, it can be used for assaying glucose in human serum samples without dilution, indicating potential for clinical diagnostic applications. Graphical abstract Nickel sulfide nanoworms (Ni3S2 NWs)/poly (3,4-ethylenedioxythiophene)-reduced graphene oxide hybrid films (PEDOT-rGO HFs) were used to construct a binder-free high-performance non-enzymatic glucose sensor with satisfactory sensitivity, wide linear range, low detection limit, good selectivity, amazing reproducibility, and stability.

Highly Responsive and Ultrasensitive Non-Enzymatic Electrochemical Glucose Sensor Based on Au Foam.

Glucose concentration is an important physiological index, therefore methods for sensitive detection of glucose are important. In this study, Au foam was prepared by electrodeposition with a dynamic gas template on an Au nanoparticle/Si substrate. The Au foam showed ultrasensitivity, high selectivity, and long-term stability in the quantitative detection of glucose. The foam was used as an electrode, and the amperometric response indicated excellent catalytic activity in glucose oxidation, with a linear response across the concentration range 0.5 µM to 12 mM, and a limit of detection of 0.14 µM. High selectivity for interfering molecules at six times the normal level and long-term stability for 30 days were obtained. The results for electrochemical detection with Au foam of glucose in human serum were consistent with those obtained with a sensor based on surface-enhanced Raman spectroscopy and a commercial sensor. This proves that this method can be used with real samples. These results show that Au foam has great potential for use as a non-enzymatic glucose sensor.

Cu(I) Coordination Complex Precursor for Randomized CuOx Microarray Loaded on Carbon Nanofiber with Excellent Electrocatalytic Performance for Electrochemical Glucose Detection.

A homoleptic ionic Cu(I) coordination complex that was based on 2,2'-biquinoline ligand functionalized with long alkyl chains (Cu(I)-C18) was used as a precursor to modify a carbon nanofiber paste electrode (Cu-C18/CNF). Randomized copper oxide microelectrode arrays dispersed within carbon nanofiber paste (CuOx/CNF) were obtained by electrochemical treatment of Cu-C18/CNF while using cyclic voltammetry (CV). The CuOx/CNF exhibited high electrocatalytic activity towards glucose oxidation at +0.6 V and +1.2 V vs. Ag/AgCl. Infrared Spectroscopy (FTIR) and scanning electron microscopy (SEM) characterized the electrodes composition. Cyclic voltammetry (CV), square wave-voltammetry (SWV), and multiple-pulsed amperometry (MPA) techniques provided optimized conditions for glucose oxidation and detection. A preconcentration step that involved 10 minutes accumulation at open circuit potential before SWV running led to the lowest limit of detection and the highest sensitivity for glucose detection (5419.77 µA·mM-1·cm-2 at + 1.1 V vs. Ag/AgCl) vs. Cu-based electrodes reported to date in literature.

Synthesis of CuNP-Modified Carbon Electrodes Obtained by Pyrolysis of Paper.

A one-step approach for the synthesis and integration of copper nanoparticles (CuNPs) onto paper-based carbon electrodes is herein reported. The method is based on the pyrolysis (1000 °C under a mixture of 95% Ar / 5% H2 for 1 hour) of paper strips modified with a saturated solution of CuSO4 and yields to the formation of abundant CuNPs on the surface of carbonized cellulose fibers. The resulting substrates were characterized by a combination of scanning electron microscopy, EDX, Raman spectroscopy as well as electrical and electrochemical techniques. Their potential application, as working electrodes for nonenzymatic amperometric determination of glucose, was then demonstrated (linear response up to 3 mM and a sensitivity of 460 ± 8 µA·cm-2·mM-1). Besides being a simple and inexpensive process for the development of electrochemically-active substrates, this approach opens new possibilities for the in-situ synthesis of metallic nanoparticles without the traditional requirements of solutions and adjuvants.

Bacteria-Templated NiO Nanoparticles/Microstructure for an Enzymeless Glucose Sensor.

The bacterial-induced hollow cylinder NiO (HCNiO) nanomaterial was utilized for the enzymeless (without GOx) detection of glucose in basic conditions. The determination of glucose in 0.05 M NaOH solution with high sensitivity was performed using cyclic voltammetry (CV) and amperometry (i-t). The fundamental electrochemical parameters were analyzed and the obtained values of diffusion coefficient (D), heterogeneous rate constant (ks), electroactive surface coverage (Г), and transfer coefficient (alpha-α) are 1.75 × 10(-6) cm²/s, 57.65 M(-1)·s(-1), 1.45 × 10(-10) mol/cm², and 0.52 respectively. The peak current of the i-t method shows two dynamic linear ranges of calibration curves 0.2 to 3.5 µM and 0.5 to 250 µM for the glucose electro-oxidation. The Ni(2+)/Ni(3+) couple with the HCNiO electrode and the electrocatalytic properties were found to be sensitive to the glucose oxidation. The green chemistry of NiO preparation from bacteria and the high catalytic ability of the oxyhydroxide (NiOOH) is the good choice for the development of a glucose sensor. The best obtained sensitivity and limit of detection (LOD) for this sensor were 3978.9 µA mM(-1)·cm(-2) and 0.9 µM, respectively.

Disposable Non-Enzymatic Glucose Sensors Using Screen-Printed Nickel/Carbon Composites on Indium Tin Oxide Electrodes.

Disposable screen-printed nickel/carbon composites on indium tin oxide (ITO) electrodes (DSPNCE) were developed for the detection of glucose without enzymes. The DSPNCE were prepared by screen-printing the ITO substrate with a 50 wt% nickel/carbon composite, followed by curing at 400 °C for 30 min. The redox couple of Ni(OH)2/NiOOH was deposited on the surface of the electrodes via cyclic voltammetry (CV), scanning from 0-1.5 V for 30 cycles in 0.1 M NaOH solution. The DSPNCE were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical methods. The resulting electrical currents, measured by CV and chronoamperometry at 0.65 V vs. Ag/AgCl, showed a good linear response with glucose concentrations from 1.0-10 mM. Also, the prepared electrodes showed no interference from common physiologic interferents such as uric acid (UA) or ascorbic acid (AA). Therefore, this approach allowed the development of a simple, disposable glucose biosensor.

Carbon fibre-supported hierarchical NiCo layered double hydroxide nanosheets as non-enzymatic glucose sensors for sport drinks and serum.

We report a systematic study of carbon fibre (CF)-supported NiCo layered double hydroxide nanosheets (LDHNs) with and without heat treatment at 200 and 400 °C (CF-NiCo LDHN200 and CF-NiCo oxide nanoparticles (NPs), respectively) as catalysts and sensors for glucose oxidation reactions (GORs). Tafel measurements for the GORs showed that the exchange current density of CF-NiCo LDHN was 1.91 × 10-3 mA·cm-2 at an early rest potential of -0.422 V. This was markedly higher than those of CF-NiCo LDHN200 (1.22 × 10-3 mA·cm-2 at - 0.352 V) and CF-NiCo oxide NP (1.18 × 10-3 mA·cm-2 at -0.327 V). The electron transfer number and Tafel slopes suggested that the glucose dehydrogenation step and one-electron release occurred first in the GORs. Amperometric measurements revealed high recoveries (101.92% and 98.92%) and low relative standard deviations (1.98% and 2.34%) for the determination of glucose using the CF-NiCo LDHN in sports drink samples and human serum.

Construction of a binder-free non-enzymatic glucose sensor based on Cu@Ni core-shell nanoparticles anchored on 3D chiral carbon nanocoils-nickel foam hierarchical scaffold.

Bimetallic nanostructures composited with carbonaceous materials are the potential contenders for quantitative glucose measurement owing to their unique nanostructures, high biomimetic activity, synergistic effects, good conductivity and chemical stability. In the present work, chemical vapors deposition technique has been employed to grow 3D carbon nanocoils (CNCs) with a chiral morphology on hierarchical macroporous nickel foam (NF) to get a CNCs/NF scaffold. Following, bimetallic Cu@Ni core-shell nanoparticles (CSNPs) are effectively coupled with this scaffold through a facile solvothermal route in order to fabricate a binder-free novel Cu@Ni CSNPs/CNCs/NF hybrid nanostructure. The constructed free-standing 3D hierarchical composite electrode guarantees highly efficient glucose redox activity due to core-shell synergistic effects, enhanced electrochemical active surface area, excellent electrochemical stability, improved conductivity with better ion diffusivity and accelerated reaction kinetics. Being a non-enzymatic glucose sensor, this electrode achieves highly swift response time of 0.1 s, ultra-high sensitivity of 6905 µA mM-1 cm-2, low limit of detection of 0.03 µM along with potential selectivity and good storage stability. Moreover, the proposed sensor is also tested successfully for the determination of glucose concentration in human serum samples under good recovery ranging from 96.6 to 102.1 %. The 3D Cu@Ni CSNPs/CNCs/NF composite electrode with unprecedented catalytic performance can be utilized as an ideal biomimetic catalyst in the field of non-enzymatic glucose sensing.