Fault Diagnosis for Abnormal Wear of Rolling Element Bearing Fusing Oil Debris Monitoring.

The abnormal wear of a rolling element bearing caused by early failures, such as pitting and spalling, will deteriorate the running state and reduce the life. This paper demonstrates the importance of oil debris monitoring and its effective feature extraction for bearing health assessment. In this paper, a rolling bearing-rotor test rig with forced lubrication is set up and the nonferrous contaminants with higher hardness were introduced artificially to accelerate the occurrence of pitting and spalling. The early failure and abnormal wear of rolling bearings cannot be effectively detected only through the vibration signal; the temperature and oil debris monitoring data are also collected synchronously. Two features regarding the ferrous particle size distribution are extracted and fused with vibration based-features to form a feature set. The sensitive features are extracted from the features set using the Neighborhood Component Analysis method to avoid feature redundancy. Finally, the importance of the oil debris based-features for the diagnosis of abnormal bearing wear is analyzed with different machine learning algorithms. Taking SVM classifier as an example, the experiment results show that the introduction of oil debris based-features increases the diagnostic accuracy by 15.7%.

Automated Adrenal Gland Disease Classes Using Patch-Based Center Symmetric Local Binary Pattern Technique with CT Images.

Incidental adrenal masses are seen in 5% of abdominal computed tomography (CT) examinations. Accurate discrimination of the possible differential diagnoses has important therapeutic and prognostic significance. A new handcrafted machine learning method has been developed for the automated and accurate classification of adrenal gland CT images. A new dataset comprising 759 adrenal gland CT image slices from 96 subjects were analyzed. Experts had labeled the collected images into four classes: normal, pheochromocytoma, lipid-poor adenoma, and metastasis. The images were preprocessed, resized, and the image features were extracted using the center symmetric local binary pattern (CS-LBP) method. CT images were next divided into 16 × 16 fixed-size patches, and further feature extraction using CS-LBP was performed on these patches. Next, extracted features were selected using neighborhood component analysis (NCA) to obtain the most meaningful ones for downstream classification. Finally, the selected features were classified using k-nearest neighbor (kNN), support vector machine (SVM), and neural network (NN) classifiers to obtain the optimum performing model. Our proposed method obtained an accuracy of 99.87%, 99.21%, and 98.81% with kNN, SVM, and NN classifiers, respectively. Hence, the kNN classifier yielded the highest classification results with no pathological image misclassified as normal. Our developed fixed patch CS-LBP-based automatic classification of adrenal gland pathologies on CT images is highly accurate and has low time complexity [Formula: see text]. It has the potential to be used for screening of adrenal gland disease classes with CT images.

Multi-classification deep CNN model for diagnosing COVID-19 using iterative neighborhood component analysis and iterative ReliefF feature selection techniques with X-ray images.

Background: The acute respiratory syndrome coronavirus 2 (SARS-CoV-2) disease seriously affected worldwide health. It remains an important worldwide concern as the number of patients infected with this virus and the death rate is increasing rapidly. Early diagnosis is very important to hinder the spread of the coronavirus. Therefore, this article is intended to facilitate radiologists automatically determine COVID-19 early on X-ray images. Iterative Neighborhood Component Analysis (INCA) and Iterative ReliefF (IRF) feature selection methods are applied to increase the accuracy of the performance criteria of trained deep Convolutional Neural Networks (CNN). Materials and methods: The COVID-19 dataset consists of a total of 15153 X-ray images for 4961 patient cases. The work includes thirteen different deep CNN model architectures. Normalized data of lung X-ray image for each deep CNN mesh model are analyzed to classify disease status in the category of Normal, Viral Pneumonia and COVID-19. The performance criteria are improved by applying the INCA and IRF feature selection methods to the trained CNN in order to improve the analysis, forecasting results, make a faster and more accurate decision. Results: Thirteen different deep CNN experiments and evaluations are successfully performed based on 80-20% of lung X-ray images for training and testing, respectively. The highest predictive values are seen in the analysis using INCA feature selection in the VGG16 network. The means of performance criteria obtained using the accuracy, sensitivity, F-score, precision, MCC, dice, Jaccard, and specificity are 99.14%, 97.98%, 99.58%, 98.80%, 97.81%, 98.83%, 97.68%, and 99.56%, respectively. This proposed study is indicated the useful application of deep CNN models to classify COVID-19 in X-ray images.

Machine Learning-Based Fault Location for Smart Distribution Networks Equipped with Micro-PMU.

Faults in distribution networks occur unpredictably, causing a threat to public safety and resulting in power outages. Automated, efficient, and precise detection of faulty sections could be a major element in immediately restoring networks and avoiding further financial losses. Distributed generations (DGs) are used in smart distribution networks and have varied current levels and internal impedances. However, fault characteristics are completely unknown because of their stochastic nature. Therefore, in these circumstances, locating the fault might be difficult. However, as technology advances, micro-phasor measurement units (micro-PMU) are becoming more extensively employed in smart distribution networks, and might be a useful tool for reducing protection uncertainties. In this paper, a new machine learning-based fault location method is proposed for use regardless of fault characteristics and DG performance using recorded data of micro-PMUs during a fault. This method only uses the recorded voltage at the sub-station and DGs. The frequency component of the voltage signals is selected as a feature vector. The neighborhood component feature selection (NCFS) algorithm is utilized to extract more informative features and lower the feature vector dimension. A support vector machine (SVM) classifier is then applied to the decreased dimension training data. The simulations of various fault types are performed on the 11-node IEEE standard feeder equipped with three DGs. Results reveal that the accuracy of the proposed fault section identification algorithm is notable.

Emotion Recognition Using a Reduced Set of EEG Channels Based on Holographic Feature Maps.

An important function of the construction of the Brain-Computer Interface (BCI) device is the development of a model that is able to recognize emotions from electroencephalogram (EEG) signals. Research in this area is very challenging because the EEG signal is non-stationary, non-linear, and contains a lot of noise due to artifacts caused by muscle activity and poor electrode contact. EEG signals are recorded with non-invasive wearable devices using a large number of electrodes, which increase the dimensionality and, thereby, also the computational complexity of EEG data. It also reduces the level of comfort of the subjects. This paper implements our holographic features, investigates electrode selection, and uses the most relevant channels to maximize model accuracy. The ReliefF and Neighborhood Component Analysis (NCA) methods were used to select the optimal electrodes. Verification was performed on four publicly available datasets. Our holographic feature maps were constructed using computer-generated holography (CGH) based on the values of signal characteristics displayed in space. The resulting 2D maps are the input to the Convolutional Neural Network (CNN), which serves as a feature extraction method. This methodology uses a reduced set of electrodes, which are different between men and women, and obtains state-of-the-art results in a three-dimensional emotional space. The experimental results show that the channel selection methods improve emotion recognition rates significantly with an accuracy of 90.76% for valence, 92.92% for arousal, and 92.97% for dominance.

Neighborhood component analysis for modeling papermaking wastewater treatment processes.

It is of great importance to obtain accurate effluent quality indices in time for pulping and papermaking wastewater treatment processes. However, considering the complex characteristics of industrial wastewater treatment systems, conventional modeling methods such as partial least squares (PLS) and artificial neural networks (ANN) cannot achieve satisfactory prediction accuracy. As a supervised metric learning method, neighborhood component analysis (NCA) is able to significantly improve the prediction performance by training an appropriate model in metric space using the distance between samples for papermaking wastewater treatment processes. The results on two data sets show that NCA has a higher prediction accuracy compared with PLS and ANN. Specifically, NCA has the highest determination coefficient (R2) and the lowest root mean square error in a benchmark simulation data set. On the other hand, the results on the data from an industrial wastewater process indicate that NCA has better modeling accuracy and its R2 increases by 32.80% and 29.08% compared with PLS and ANN, respectively. NCA provides a feasible way to realize online monitoring and automatic control in wastewater treatment processes.

Machine Learning Diagnostic Modeling for Classifying Fibromyalgia Using B-mode Ultrasound Images.

Fibromyalgia (FM) diagnosis remains a challenge for clinicians due to a lack of objective diagnostic tools. One proposed solution is the use of quantitative ultrasound (US) techniques, such as image texture analysis, which has demonstrated discriminatory capabilities with other chronic pain conditions. From this, we propose the use of image texture variables to construct and compare two machine learning models (support vector machine [SVM] and logistic regression) for differentiating between the trapezius muscle in healthy and FM patients. US videos of the right and left trapezius muscle were acquired from healthy (n = 51) participants and those with FM (n = 57). The videos were converted into 64,800 skeletal muscle regions of interest (ROIs) using MATLAB. The ROIs were filtered by an algorithm using the complex wavelet structural similarity index (CW-SSIM), which removed ROIs that were similar. Thirty-one texture variables were extracted from the ROIs, which were then used in nested cross-validation to construct SVM and elastic net regularized logistic regression models. The generalized performance accuracy of both models was estimated and confirmed with a final validation on a holdout test set. The predicted generalized performance accuracy of the SVM and logistic regression models was computed to be 83.9 ± 2.6% and 65.8 ± 1.7%, respectively. The models achieved accuracies of 84.1%, and 66.0% on the final holdout test set, validating performance estimates. Although both machine learning models differentiate between healthy trapezius muscle and that of patients with FM, only the SVM model demonstrated clinically relevant performance levels.

Wind Turbine Gearbox Condition Monitoring Based on Class of Support Vector Regression Models and Residual Analysis.

The intelligent condition monitoring of wind turbines reduces their downtime and increases reliability. In this manuscript, a feature selection-based methodology that essentially works on regression models is used for identifying faulty scenarios. Supervisory control and data acquisition (SCADA) data with 1009 samples from one year and one month before failure are considered. Gearbox oil and bearing temperatures are treated as target variables with all the other variables used for the prediction model. Neighborhood component analysis (NCA) as a feature selection technique is employed to select the best features and prediction performance for several machine learning regression models is assessed. The results reveal that twin support vector regression (99.91%) and decision trees (98.74%) yield the highest accuracy for gearbox oil and bearing temperatures respectively. It is observed that NCA increases the accuracy and thus reliability of the condition monitoring system. Furthermore, the residuals from the class of support vector regression (SVR) models are tested from a statistical point of view. Diebold-Mariano and Durbin-Watson tests are carried out to establish the robustness of the tested models.

NIR Hyperspectral Imaging Technology Combined with Multivariate Methods to Study the Residues of Different Concentrations of Omethoate on Wheat Grain Surface.

In this study, a hyperspectral imaging system of 866.4-1701.0 nm was selected and combined with multivariate methods to identify wheat kernels with different concentrations of omethoate on the surface. In order to obtain the optimal model combination, three preprocessing methods (standard normal variate (SNV), Savitzky-Golay first derivative (SG1), and multivariate scatter correction (MSC)), three feature extraction algorithms (successive projections algorithm (SPA), random frog (RF), and neighborhood component analysis (NCA)), and three classifier models (decision tree (DT), k-nearest neighbor (KNN), and support vector machine (SVM)) were applied to make a comparison. Firstly, based on the full wavelengths modeling analysis, it was found that the spectral data after MSC processing performed best in the three classifier models. Secondly, three feature extraction algorithms were used to extract the feature wavelength of MSC processed data and based on feature wavelengths modeling analysis. As a result, the MSC-NCA-SVM model performed best and was selected as the best model. Finally, in order to verify the reliability of the selected model, the hyperspectral image was substituted into the MSC-NCA-SVM model and the object-wise method was used to visualize the image classification. The overall classification accuracy of the four types of wheat kernels reached 98.75%, which indicates that the selected model is reliable.

Optimizing multi-spectral ore sorting incorporating wavelength selection utilizing neighborhood component analysis for effective arsenic mineral detection.

Arsenic contamination not only complicates mineral processing but also poses environmental and health risks. To address these challenges, this research investigates the feasibility of utilizing Hyperspectral imaging combined with machine learning techniques for the identification of arsenic-containing minerals in copper ore samples, with a focus on practical application in sorting and processing operations. Through experimentation with various copper sulfide ores, Neighborhood Component Analysis (NCA) was employed to select essential wavelength bands from Hyperspectral data, subsequently used as inputs for machine learning algorithms to identify arsenic concentrations. Results demonstrate that by selecting a subset of informative bands using NCA, accurate mineral identification can be achieved with a significantly reduced the size of dataset, enabling efficient processing and analysis. Comparison with other wavelength selection methods highlights the superiority of NCA in optimizing classification accuracy. Specifically, the identification accuracy showed 91.9% or more when utilizing 8 or more bands selected by NCA and was comparable to hyperspectral data analysis with 204 bands. The findings suggest potential for cost-effective implementation of multispectral cameras in mineral processing operations. Future research directions include refining machine learning algorithms, exploring broader applications across diverse ore types, and integrating hyperspectral imaging with emerging sensor technologies for enhanced mineral processing capabilities.

A highly generalized classifier for osteoporosis radiography based on multiscale fractal, lacunarity, and entropy distributions.

Background: Osteoporosis is a common degenerative disease with high incidence among aging populations. However, in regular radiographic diagnostics, asymptomatic osteoporosis is often overlooked and does not include tests for bone mineral density or bone trabecular condition. Therefore, we proposed a highly generalized classifier for osteoporosis radiography based on the multiscale fractal, lacunarity, and entropy distributions. Methods: We collected a total of 104 radiographs (92 for training and 12 for testing) of lumbar spine L4 and divided them into three groups (normal, osteopenia, and osteoporosis). In parallel, 174 radiographs (116 for training and 58 for testing) of calcaneus from health and osteoporotic fracture groups were collected. The texture feature data of all the radiographs were pulled out and analyzed. The Davies-Bouldin index was applied to optimize hyperparameters of feature counting. Neighborhood component analysis was performed to reduce feature dimension and increase generalization. A support vector machine classifier was trained with only the most effective six features for each binary classification scenario. The accuracy and sensitivity performance were estimated by calculating the area under the curve. Results: Interpretable feature trends of osteoporotic pathological changes were depicted. On the spine test dataset, the accuracy and sensitivity of binary classifiers were 0.851 (95% CI: 0.730-0.922), 0.813 (95% CI: 0.718-0.878), and 0.936 (95% CI: 0.826-1) for osteoporosis diagnosis; 0.721 (95% CI: 0.578-0.824), 0.675 (95% CI: 0.563-0.772), and 0.774 (95% CI: 0.635-0.878) for osteopenia diagnosis; and 0.935 (95% CI: 0.830-0.968), 0.928 (95% CI: 0.863-0.963), and 0.910 (95% CI: 0.746-1) for osteoporosis diagnosis from osteopenia. On the calcaneus test dataset, they were 0.767 (95% CI: 0.629-0.879), 0.672 (95% CI: 0.545-0.793), and 0.790 (95% CI: 0.621-0.923) for osteoporosis diagnosis. Conclusion: This method showed the capacity of resisting disturbance on lateral spine radiographs and high generalization on the calcaneus dataset. Pixel-wise texture features not only helped to understand osteoporosis on radiographs better but also shed new light on computer-aided osteopenia and osteoporosis diagnosis.

Identification of attention deficit hyperactivity disorder with deep learning model.

This article explores the detection of Attention Deficit Hyperactivity Disorder, a neurobehavioral disorder, from electroencephalography signals. Due to the unstable behavior of electroencephalography signals caused by complex neuronal activity in the brain, frequency analysis methods are required to extract the hidden patterns. In this study, the feature extraction was performed with the Multitaper and Multivariate Variational Mode Decomposition methods. Then, these features were analyzed with the neighborhood component analysis and the features that contribute effectively to the classification were selected. The deep learning model including the convolution, pooling, and bidirectional long short term cell and fully connected layer was trained with the selected features. The trained model could effectively classify the subjects with Attention Deficit Hyperactivity Disorder with a deep learning model, support vector machines and linear discriminant analysis. The experiments were validated with an Attention Deficit Hyperactivity Disorder open access dataset ( https://doi.org/10.21227/rzfh-zn36 ). In validation, the deep learning model was able to classify 1210 test samples (600 subjects in the control group as Normal and 610 subjects in the ADHD group as ADHD) in 0.1 s with an accuracy of 95.54%. This accuracy rate is quite high compared to the Linear Discriminant Analysis (76.38%) and Support Vector Machines (81.69%). Experimental results showed that the proposed approach can innovatively classify Attention Deficit Hyperactivity Disorder subjects from the Control group effectively.

Study of MI-BCI classification method based on the Riemannian transform of personalized EEG spatiotemporal features.

Motor imagery (MI) is a traditional paradigm of brain-computer interface (BCI) and can assist users in creating direct connections between their brains and external equipment. The common spatial patterns algorithm is the most popular spatial filtering technique for collecting EEG signal features in MI-based BCI systems. Due to the defect that it only considers the spatial information of EEG signals and is susceptible to noise interference and other issues, its performance is diminished. In this study, we developed a Riemannian transform feature extraction method based on filter bank fusion with a combination of multiple time windows. First, we proposed the multi-time window data segmentation and recombination method by combining it with a filter group to create new data samples. This approach could capture individual differences due to the variation in time-frequency patterns across different participants, thereby improving the model's generalization performance. Second, Riemannian geometry was used for feature extraction from non-Euclidean structured EEG data. Then, considering the non-Gaussian distribution of EEG signals, the neighborhood component analysis (NCA) algorithm was chosen for feature selection. Finally, to meet real-time requirements and a low complexity, we employed a Support Vector Machine (SVM) as the classification algorithm. The proposed model achieved improved accuracy and robustness. In this study, we proposed an algorithm with superior performance on the BCI Competition IV dataset 2a, achieving an accuracy of 89%, a kappa value of 0.73 and an AUC of 0.9, demonstrating advanced capabilities. Furthermore, we analyzed data collected in our laboratory, and the proposed method achieved an accuracy of 77.4%, surpassing other comparative models. This method not only significantly improved the classification accuracy of motor imagery EEG signals but also bore significant implications for applications in the fields of brain-computer interfaces and neural engineering.

NCA-GA-SVM: A new two-level feature selection method based on neighborhood component analysis and genetic algorithm in hepatocellular carcinoma fatality prognosis.

Hepatocellular carcinoma (HCC) is one of the major challenges facing biomedical research. Despite the high lethality, methods to predict mortality for this type of aggressive malignant tumor are insufficient. Machine learning is recognized by many authors as a valuable, yet poorly studied tool in this field. Undoubtedly, searching for new feature selection methods is significant in building an effective machine-learning model. In this study, we propose the novel hybrid model using neighborhood components analysis, genetic algorithm and support vector machine classifier (NCA-GA-SVM). Because SVM works with default parameters characterized by low classification results, we decided to use GA for the proper optimization and feature selection. As reported in the available literature, NCA and GA obtain high classification results. Here, we decided to combine these approaches, building a two-level algorithm for HCC fatality prognosis. We used a well-known dataset collected from 165 patients at Coimbra's Hospital and University Center, Portugal. Our results revealed 96.36% classification accuracy and 95.52% F1-score. Additionally, we compared all data for these metrics published so far. We demonstrated that our algorithm achieved the highest accuracy and can be successfully applied for the assessment of hepatocellular carcinoma mortality in the future. Our findings bring methodological value for future HCC studies and emphasize the possibility of using machine-learning techniques to improve the quality of medical decisions.

A brainnetome atlas-based methamphetamine dependence identification using neighborhood component analysis and machine learning on functional MRI data.

Addiction to methamphetamine (MA) is a major public health concern. Developing a predictive model that can classify and characterize the brain-based biomarkers predicting MA addicts may directly lead to improved treatment outcomes. In the current study, we applied the support vector machine (SVM)-based classification method to resting-state functional magnetic resonance imaging (rs-fMRI) data obtained from individuals with methamphetamine use disorder (MUD) and healthy controls (HCs) to identify brain-based features predictive of MUD. Brain connectivity analyses were conducted for 36 individuals with MUD as well as 37 HCs based on the brainnetome atlas, and the neighborhood component analysis was applied for feature selection. Eighteen most relevant features were screened out and fed into the SVM to classify the data. The classifier was able to differentiate individuals with MUD from HCs with a high prediction accuracy, sensitivity, specificity, and AUC of 88.00, 86.84, 89.19, and 0.94, respectively. The top six discriminative features associated with changes in the functional activity of key nodes in the default mode network (DMN), all the remaining discriminative features are related to the thalamic connections within the cortico-striato-thalamo-cortical (CSTC) loop. In addition, the functional connectivity (FC) between the bilateral inferior parietal lobule (IPL) and right cingulate gyrus (CG) was significantly correlated with the duration of methamphetamine use. The results of this study not only indicated that MUD-related FC alterations were predictive of group membership, but also suggested that machine learning techniques could be used for the identification of MUD-related imaging biomarkers.

Automated Diabetic Retinopathy Detection Using Horizontal and Vertical Patch Division-Based Pre-Trained DenseNET with Digital Fundus Images.

Diabetic retinopathy (DR) is a common complication of diabetes that can lead to progressive vision loss. Regular surveillance with fundal photography, early diagnosis, and prompt intervention are paramount to reducing the incidence of DR-induced vision loss. However, manual interpretation of fundal photographs is subject to human error. In this study, a new method based on horizontal and vertical patch division was proposed for the automated classification of DR images on fundal photographs. The novel sides of this study are given as follows. We proposed a new non-fixed-size patch division model to obtain high classification results and collected a new fundus image dataset. Moreover, two datasets are used to test the model: a newly collected three-class (normal, non-proliferative DR, and proliferative DR) dataset comprising 2355 DR images and the established open-access five-class Asia Pacific Tele-Ophthalmology Society (APTOS) 2019 dataset comprising 3662 images. Two analysis scenarios, Case 1 and Case 2, with three (normal, non-proliferative DR, and proliferative DR) and five classes (normal, mild DR, moderate DR, severe DR, and proliferative DR), respectively, were derived from the APTOS 2019 dataset. These datasets and these cases have been used to demonstrate the general classification performance of our proposal. By applying transfer learning, the last fully connected and global average pooling layers of the DenseNet201 architecture were used to extract deep features from input DR images and each of the eight subdivided horizontal and vertical patches. The most discriminative features are then selected using neighborhood component analysis. These were fed as input to a standard shallow cubic support vector machine for classification. Our new DR dataset obtained 94.06% and 91.55% accuracy values for three-class classification with 80:20 hold-out validation and 10-fold cross-validation, respectively. As can be seen from steps of the proposed model, a new patch-based deep-feature engineering model has been proposed. The proposed deep-feature engineering model is a cognitive model, since it uses efficient methods in each phase. Similar excellent results were seen for three-class classification with the Case 1 dataset. In addition, the model attained 87.43% and 84.90% five-class classification accuracy rates using 80:20 hold-out validation and 10-fold cross-validation, respectively, on the Case 2 dataset, which outperformed prior DR classification studies based on the five-class APTOS 2019 dataset. Our model attained about >2% classification results compared to others. These findings demonstrate the accuracy and robustness of the proposed model for classification of DR images.

Novel nested patch-based feature extraction model for automated Parkinson's Disease symptom classification using MRI images.

OBJECTIVE: Parkinson's disease (PD) is a common neurological disorder with variable clinical manifestations and magnetic resonance imaging (MRI) findings. We propose a handcrafted image classification model that can accurately (i) classify different PD stages, (ii) detect comorbid dementia, and (iii) discriminate PD-related motor symptoms. METHODS: Selected image datasets from three PD studies were used to develop the classification model. Our proposed novel automated system was developed in four phases: (i) texture features are extracted from the non-fixed size patches. In the feature extraction phase, a pyramid histogram-oriented gradient (PHOG) image descriptor is used. (ii) In the feature selection phase, four feature selectors: neighborhood component analysis (NCA), Chi2, minimum redundancy maximum relevancy (mRMR), and ReliefF are used to generate four feature vectors. (iii) Two classifiers: k-nearest neighbor (kNN) and support vector machine (SVM) are used in the classification step. A ten-fold cross-validation technique is used to validate the results. (iv) Eight predicted vectors are generated using four selected feature vectors and two classifiers. Finally, iterative majority voting (IMV) is used to attain general classification results. Therefore, this model is named nested patch-PHOG-multiple feature selectors and multiple classifiers-IMV (NP-PHOG-MFSMCIMV). RESULTS: Our presented NP-PHOG-MFSMCIMV model achieved 99.22, 98.70, and 99.53% accuracies for the collected PD stages, PD dementia, and PD symptoms classification datasets, respectively. SIGNIFICANCE: The obtained accuracies (over 98% for all states) demonstrated the performance of developed NP-PHOG-MFSMCIMV model in automated PD state classification.

Novel automated PD detection system using aspirin pattern with EEG signals.

BACKGROUND AND OBJECTIVE: Parkinson's disease (PD) is one of the most common diseases worldwide which reduces quality of life of patients and their family members. The electroencephalogram (EEG) signals coupled with various advanced machine-learning algorithms have been widely used to detect PD automatically. In this paper, we propose a novel aspirin pattern to detect PD accurately using EEG signals. METHOD: In this research, the feature generation ability of a chemical graph is investigated. Therefore, this work presents a new graph-based aspirin model for automated PD detection using EEG signals. The proposed method consists of (i) multilevel feature generation phase involving new aspirin pattern, statistical moments, and maximum absolute pooling (MAP), (ii) selection of most discriminative features using neighborhood component analysis (NCA), and (iii) classification using k nearest neighbor (kNN) for automated detection of PD and (iv) iterative majority voting. RESULTS: A public dataset has been used to develop the proposed model. Two cases are created, and these cases consisted of two classes. Leave one subject out (LOSO) validation have been used to calculate robust results. Our proposal achieved 93.57% and 95.48% classification accuracies for Case 1 and Case 2 respectively. CONCLUSION: Our developed automated PD model is accurate and equipped to be tested with more diverse EEG datasets.

Predication of different stages of Alzheimer's disease using neighborhood component analysis and ensemble decision tree.

BACKGROUND: There is a spectrum of the progression from healthy control (HC) to mild cognitive impairment (MCI) without conversion to Alzheimer's disease (AD), to MCI with conversion to AD (cMCI), and to AD. This study aims to predict the different disease stages using brain structural information provided by magnetic resonance imaging (MRI) data. NEW METHOD: The neighborhood component analysis (NCA) is applied to select most powerful features for prediction. The ensemble decision tree classifier is built to predict which group the subject belongs to. The best features and model parameters are determined by cross validation of the training data. RESULTS: Our results show that 16 out of a total of 429 features were selected by NCA using 240 training subjects, including MMSE score and structural measures in memory-related regions. The boosting tree model with NCA features can achieve prediction accuracy of 56.25% on 160 test subjects. COMPARISON WITH EXISTING METHOD(S): Principal component analysis (PCA) and sequential feature selection (SFS) are used for feature selection, while support vector machine (SVM) is used for classification. The boosting tree model with NCA features outperforms all other combinations of feature selection and classification methods. CONCLUSIONS: The results suggest that NCA be a better feature selection strategy than PCA and SFS for the data used in this study. Ensemble tree classifier with boosting is more powerful than SVM to predict the subject group. However, more advanced feature selection and classification methods or additional measures besides structural MRI may be needed to improve the prediction performance.

Sleep stage classification using single-channel EOG.

Sleep stage classification is an important task for the timely diagnosis of sleep disorders and sleep-related studies. In this paper, automatic scoring of sleep stages using Electrooculogram (EOG) is presented. Single channel EOG signals are analyzed in Discrete Wavelet Transform (DWT) domain employing various statistical features such as Spectral Entropy, Moment-based Measures, Refined Composite Multiscale Dispersion Entropy (RCMDE) and Autoregressive (AR) Model Coefficients. The discriminating ability of the features is studied using the One Way Analysis of Variance (ANOVA) and box plots. A feature reduction algorithm based on Neighborhood Component Analysis is used to reduce the model complexity and select the features with highest discriminating abilities. Random Under-Sampling Boosting (RUSBoost), Random Forest (RF) and Support Vector Machine (SVM) are employed to classify various sleep stages for 2-6 stage classification problem. Performance of the proposed method is studied using three publicly available databases, the Sleep-EDF, Sleep-EDFX and ISRUC-Sleep databases consisting of 8, 20 and 10 subjects respectively. The proposed method outperforms the state-of-the-art EOG based techniques in accuracy. In addition, its performance is shown to be on par or better than those of various single channel EEG based methods. An important limitation of existing sleep detection methods is the low accuracy of the S1 sleep stage classification for which the proposed method using the RUSBoost classifier gives a superior accuracy as compared to those of EOG and EEG based techniques.