The Recyclability of Fire-Retarded Biobased Polyamide 11 (PA11) Composites Reinforced with Basalt Fibers (BFs): The Influence of Reprocessing on Structure, Properties, and Fire Behavior.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FRs). Significant amounts of FRs are usually required to effectively affect a polymer's burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but also, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of the four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame-retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC), and pentaerythritol (PER) and its composites containing additional short basalt fibers (BFs). Composites manufactured via twin-screw extrusion were subjected to four reprocessing cycles using injection molding. A comprehensive analysis of their structural, mechanical, and fire behavior changes in each cycle was conducted. The obtained results confirmed the safety of using the proposed fire-retarded polyamide and its composites while reprocessing under the recommended process parameters without the risk of significant changes in the structure. The partial increase in flammability of reprocessed PA-based materials caused mainly by polymer degradation has been described.

Surface Functionalization of Poly(lactic acid) via Deposition of Hydroxyapatite Monolayers for Biomedical Applications.

The surface modification of poly(lactic acid) (PLA) using hydroxyapatite (HAP) particles via Langmuir-Blodgett (LB) and Langmuir-Schaefer (LS) approaches has been reported. The HAP monolayer was characterized at the air/water interface and deposited on three-dimensional (3D) printed poly(lactic acid). The deposition of HAP particles using the LS approach led to a larger surface coverage in comparison to the LB method, which produces a less uniform coating because of the aggregation of the particles. After the transfer of HAP on the PLA surface, the wettability values remained within the desired range. The presence of HAP on the surface of the polymer altered the topography and roughness in the nanoscale, as evidenced by the atomic force microscopy (AFM) images. This effect can be beneficial for the osteointegration of polymeric implants at an early stage, as well as for the reduction of the adherence of the microbial biofilm. Overall, the results suggest that the LS technique could be a promising approach for surface modification of PLA by hydroxyapatite with respective advantages in the biomedical field.

An Automatic Biopsy Needle Detection and Segmentation on Ultrasound Images Using a Convolutional Neural Network.

Needle visualization in the ultrasound image is essential to successfully perform the ultrasound-guided core needle biopsy. Automatic needle detection can significantly reduce the procedure time, false-negative rate, and highly improve the diagnosis. In this paper, we present a CNN-based, fully automatic method for detection of core needle in 2D ultrasound images. Adaptive moment estimation optimizer is proposed as CNN architecture. Radon transform is applied to locate the needle. The network's model was trained and tested on the total of 619 2D images from 91 cases of breast cancer. The model has achieved an average weighted intersection over union (the weighted Jaccard Index) of 0.986, F1 Score of 0.768, and angle RMSE of 3.73°. The obtained results exceed the other solutions by at least 0.27 and 7° in case of F1 score and angle RMSE, respectively. Finally, the needle is detected in a single frame averagely in 21.6 ms on a modern PC.

The Development of Sustainable Polyethylene Terephthalate Glycol-Based (PETG) Blends for Additive Manufacturing Processing-The Use of Multilayered Foil Waste as the Blend Component.

The polymer foil industry is one of the leading producers of plastic waste. The development of new recycling methods for packaging products is one of the biggest demands in today's engineering. The subject of this research was the melt processing of multilayered PET-based foil waste with PETG copolymer. The resulting blends were intended for additive manufacturing processing using the fused deposition modeling (FDM) method. In order to improve the properties of the developed materials, the blends compounding procedure was conducted with the addition of a reactive chain extender (CE) and elastomeric copolymer used as an impact modifier (IM). The samples were manufactured using the 3D printing technique and, for comparison, using the traditional injection molding method. The obtained samples were subjected to a detailed characterization procedure, including mechanical performance evaluation, thermal analysis, and rheological measurements. This research confirms that PET-based film waste can be successfully used for the production of filament, and for most samples, the FDM printing process can be conducted without any difficulties. Unfortunately, the unmodified blends are characterized by brittleness, which makes it necessary to use an elastomer additive (IM). The presence of a semicrystalline PET phase improves the thermal resistance of the prepared blends; however, an annealing procedure is required for this purpose.

Mechanical and Rheological Evaluation of Polyester-Based Composites Containing Biochar.

The use of biodegradable polymers as matrices in composites gives a wide range of applications, especially in niche areas. The assessment of the effect of the filler content on the change of mechanical properties makes it possible to optimize the composition for specific needs. Biochar was used as a filler in the studied composites with two different biodegradable blends as a matrix. Poly(1,4-butylene adipate-co-1,4-butylene terephthalate)/polylactide/biochar (PBAT/PLA/BC) and polylactide/poly[(R)-3-hydroxybutyrate-co-4-hydroxybutyrate]/biochar (PLA/P(3HB-co-4HB)/BC) composites with 0, 10, 15, 20 and 30 wt% of biochar underwent mechanical tests. The test results revealed a change in the properties of the composites related to the filler content. The results of the tensile test showed that increasing the biochar content increased the tensile modulus values by up to 100% for composites with 30 wt% of biochar, compared to unfilled matrices, and decreased the elongation associated with the breaking of PBAT/PLA and PLA/P(3HB-co-4HB) matrix composites. The elongation values at break of PBAT/PLA and PLA/(3HB-co-4HB) composites with 30 wt% biochar were reduced by 50% and 65%, respectively, compared to the unfilled matrices. PLA/P(3HB-co-4HB) matrix composites, in contrast to PBAT/PLA/BC, showed a decrease in tensile strength with the increases in filler content from 35.6 MPa for unfilled matrix to 27.1 MPa for PLA/P(3HB-co-4HB)/BC30 composites. An increase in filler content increased the brittleness of the composites regardless of the matrix used, as determined under the Charpy impact-test. This phenomenon was observed for all tested PLA/P(3HB-co-4HB) composites, for which the impact strength decreased from 4.47 kJ/m2 for the matrix to 1.61 kJ/m2 for the composite containing 30 wt% biochar. PBAT/PLA-based composites with 10 wt% of biochar showed slightly lower impact strength compared to the unfilled matrix, but composites with 30 wt% biochar showed 30% lower impact strength than PBAT/PLA. The complex viscosity value increased with increased filler content. For all composites tested on both polyester matrices, the viscosity decreased with increasing angular frequency.

(Bio)degradable Biochar Composites of PLA/P(3HB-co-4HB) Commercial Blend for Sustainable Future-Study on Degradation and Electrostatic Properties.

Interesting alternatives to expensive biodegradable polymers are their composites with natural fillers. The addition of biochar to a blend of poly(lactic acid) (PLA) and poly(3-hydroxybutyrate-co-4-hydroxybutyrate) was studied, and the resulting materials were evaluated for their properties and changes during degradation. Introducing biochar as a filler brought a noticeable improvement in electrostatic properties. Surface resistivity decreased from 3.80 × 1012 for the sample without biochar to 1.32 × 1012 for the sample with 30% filler content. Degradation tests revealed distinct differences in the degradation profile for composites due to the presence of filler. Composites with a lower biochar content displayed curling crack edges during hydrolytic degradation, and when the filler content reached 20 wt%, PLA loss accelerated. This study suggests that biochar-based composites have potential to be used as sustainable materials with improved properties.

The Development of Poly(lactic acid) (PLA)-Based Blends and Modification Strategies: Methods of Improving Key Properties towards Technical Applications-Review.

The widespread use of poly(lactic acid) (PLA) from packaging to engineering applications seems to follow the current global trend. The development of high-performance PLA-based blends has led to the commercial introduction of various PLA-based resins with excellent thermomechanical properties. The reason for this is the progress in the field of major PLA limitations such as low thermal resistance and poor impact strength. The main purpose of using biobased polymers in polymer blends is to increase the share of renewable raw materials in the final product rather than its possible biodegradation. However, in the case of engineering applications, the focus is on achieving the required properties rather than maximizing the percentage of biopolymer. The presented review article discusses the current strategies to optimize the balance of the key features such as stiffness, toughness, and heat resistance of PLA-based blends. Improving of these properties requires molecular structural changes, which together with morphology, crystallinity, and the influence of the processing conditions are the main subjects of this article. The latest research in this field clearly indicates the high potential of using PLA-based materials in highly demanding applications. In the case of impact strength modification, it is possible to obtain values close to 800 J/m, which is a value comparable to polycarbonate. Significant improvement can also be confirmed for thermal resistance results, where heat deflection temperatures for selected types of PLA blends can reach even 130 °C after modification. The modification strategies discussed in this article confirm that a properly conducted process of selecting the blend components and the conditions of the processing technique allows for revealing the potential of PLA as an engineering plastic.

Design, clinical applications and post-surgical assessment of bioresorbable 3D-printed craniofacial composite implants.

This study details the design, fabrication, clinical trials' evaluation, and analysis after the clinical application of 3D-printed bone reconstruction implants made of nHAp@PLDLLA [nanohydroxyapatite@poly(L-lactide-co-D,L-lactide)] biomaterial. The 3D-printed formulations have been tested as bone reconstruction Cranioimplants in 3 different medical cases, including frontal lobe, mandibular bone, and cleft palate reconstructions. Replacing one of the implants after 6 months provided a unique opportunity to evaluate the post-surgical implant obtained from a human patient. This allowed us to quantify physicochemical changes and develop a spatial map of osseointegration and material degradation kinetics as a function of specific locations. To the best of our knowledge, hydrolytic degradation and variability in the physicochemical and mechanical properties of the biomimetic, 3D-printed implants have not been quantified in the literature after permanent placement in the human body. Such analysis has revealed the constantly changing properties of the implant, which should be considered to optimize the design of patient-specific bone substitutes. Moreover, it has been proven that the obtained composition can produce biomimetic, bioresorbable and bone-forming alloplastic substitutes tailored to each patient, allowing for shorter surgery times and faster patient recovery than currently available methods.

Overview of the Cast Polyolefin Film Extrusion Technology for Multi-Layer Packaging Applications.

The review article presents the technology of producing polyolefin-based films by extrusion casting. Due to the wide use of this type of film as packaging for food and other goods, obtaining films with favorable properties is still a challenge for many groups of producers in the plastics market. The feedblock process and multimanifold process are the main methods of producing multi-layer film. In the case of food films, appropriate barrier properties are required, as well as durability and puncture resistance also at low temperatures. On the other hand, in order to properly pack and present products, an appropriate degree of transparency must be maintained. Therefore, processing aids such as anti-slip, anti-block and release agents are commonly used. Other popular modifiers, such as waxes, fatty acid amides and mineral fillers-silica, talc or calcium carbonate-and their use in film extrusion are discussed. The article also presents common production problems and their prevention.

Effect of the Advanced Cranial and Craniofacial Implant Fabrication on Their Degradation Affinity.

Biodegradable craniofacial and cranial implants are a new aspect in terms of reducing potential complications, especially in the long term after surgery. They are also an important contribution in the field of surgical reconstructions for children, for whom it is important to restore natural bone in a relatively short time, due to the continuous growth of bones. The aim of this study was to verify the impact of the technology on biodegradability and to estimate the risk of inappropriate implant resorption time, which is an important aspect necessary to select prototypes of implants for in vivo testing. Prototypes of implants were made using two technologies: 3D printing using a PLDLA: poly(L-co-D,L lactide) (PLDLA) filament containing hydroxyapatite nanoparticles, and injection using PLDLA. After the radiation sterilization process, they were subjected to in vitro degradation under accelerated conditions. As part of this study, the in vitro degradation of newly developed biodegradable implant technologies was assessed in accordance with the guidelines of European standards. It was found that the implant manufacturing process had a significant impact on the degradation time under simulated conditions in various media. Implants made using the injection technique were characterized by lower susceptibility to degradation media compared to the 3D-printed implant under accelerated conditions.

Development of a New Type of Flame Retarded Biocomposite Reinforced with a Biocarbon/Basalt Fiber System: A Comparative Study between Poly(lactic Acid) and Polypropylene.

A new type of partially biobased reinforcing filler system was developed in order to be used as a flame retardant for polylactic acid (PLA) and polypropylene (PP)-based composites. The prepared materials intended for injection technique processing were melt blended using the novel system containing ammonium polyphosphate (EX), biocarbon (BC), and basalt fibers (BF). All of the prepared samples were subjected to a detailed analysis. The main criterion was the flammability of composites. For PLA-based composites, the flammability was significantly reduced, up to V-0 class. The properties of PLA/EX/BC and PLA/EX/(BC-BF) composites were characterized by their improved mechanical properties. The conducted analysis indicates that the key factor supporting the effectiveness of EX flame retardants is the addition of BC, while the use of BF alone increases the flammability of the samples to the reference level. The results indicate that the developed materials can be easily applied in industrial practice as effective and sustainable flame retardants.

The Use of Nanoscale Montmorillonite (MMT) as Reinforcement for Polylactide Acid (PLA) Prepared by Fused Deposition Modeling (FDM)-Comparative Study with Biocarbon and Talc Fillers.

The subject of the presented research focuses on a comparative assessment of three types of polymer fillers used to modify highly crystalline poly(lactic acid) PLA intended for the FDM technique. The aim of the presented work was to determine the performance of the developed materials. The key aspect of the work was the use of polymer fillers of three different types. Nano-sized montmorillonite (MMT), biobased biocarbon (BC) and mineral talc. The several types of composites were prepared using extrusion technique. The maximum content for BC and talc filler was limited to 20 wt%, while for MMT it was 5 wt%. Prepared samples were subjected to detailed material analysis including mechanical tests (tensile, flexural, Charpy), thermal analysis (DSC, DMTA), HDT/Vicat tests and structure analysis. The results of the test confirmed that even relatively small amount of nano-type filler can be more efficient than micrometric particles. The used type of matrix was highly crystalline PLA, which resulted in a significant nucleation effect of the crystalline structure. However, thermomechanical tests revealed no improvement in thermal resistance. Microscopic survey confirmed that for MMT and talc filler the structure anisotropy was leading to more favorable properties, especially when compared to structures based on spherical BC particles.

A Novel Manufacturing Concept of LCP Fiber-Reinforced GPET-Based Sandwich Structures with an FDM 3D-Printed Core.

The presented research was focused on the development of a new method of sandwich structure manufacturing involving FDM-printing (fused deposition modeling) techniques and compression molding. The presented concept allows for the preparation of thermoplastic-based composites with enhanced mechanical properties. The sample preparation process consists of 3D printing the sandwich's core structure using the FDM method. For comparison purposes, we used two types of GPET (copolymer of polyethylene terephthalate)-based filaments, pure resin, and carbon fiber (CF)-reinforced filaments. The outer reinforcing layer "skins" of the sandwich structure were prepared from the compression molded prepregs made from the LCP (liquid-crystal polymer)-fiber fabric with the GPET-based matrix. The final product consisting of an FDM-printed core and LCP-based prepreg was prepared using the compression molding method. The prepared samples were subjected to detailed materials analyses, including thermal analyses (thermogravimetry-TGA, differencial scanning calorimetry-DSC, and dynamic thermal-mechanical analysis-DMTA) and mechanical tests (tensile, flexural, and impact). As indicated by the static test results, the modulus and strength of the prepared composites were slightly improved; however, the stiffness of the prepared materials was more related to the presence of the CF-reinforced filament than the presence of the composite prepreg. The main advantage of using the developed method is revealed during impact tests. Due to the presence of long LCP fibers, the prepared sandwich samples are characterized by very high impact resistance. The impact strength increased from 1.7 kJ/m2 for pure GPET samples to 50.4 kJ/m2 for sandwich composites. For GPET/CF samples, the increase is even greater. The advantages of the developed solution were illustrated during puncture tests in which none of the sandwich samples were pierced.

Thermomechanical and Fire Properties of Polyethylene-Composite-Filled Ammonium Polyphosphate and Inorganic Fillers: An Evaluation of Their Modification Efficiency.

The development of new polymer compositions characterized by a reduced environmental impact while lowering the price for applications in large-scale production requires the search for solutions based on the reduction in the polymer content in composites' structure, as well as the use of fillers from sustainable sources. The study aimed to comprehensively evaluate introducing low-cost inorganic fillers, such as copper slag (CS), basalt powder (BP), and expanded vermiculite (VM), into the flame-retarded ammonium polyphosphate polyethylene composition (PE/APP). The addition of fillers (5-20 wt%) increased the stiffness and hardness of PE/APP, both at room and at elevated temperatures, which may increase the applicability range of the flame retardant polyethylene. The deterioration of composites' tensile strength and impact strength induced by the presence of inorganic fillers compared to the unmodified polymer is described in detail. The addition of BP, CS, and VM with the simultaneous participation of APP with a total share of 40 wt% caused only a 3.1, 4.6, and 3 MPa decrease in the tensile strength compared to the reference value of 23 MPa found for PE. In turn, the cone calorimeter measurements allowed for the observation of a synergistic effect between APP and VM, reducing the peak heat rate release (pHRR) by 60% compared to unmodified PE. Incorporating fillers with a similar thermal stability but differing particle size distribution and shape led to additional information on their effectiveness in changing the properties of polyethylene. Critical examinations of changes in the mechanical and thermomechanical properties related to the structure analysis enabled the definition of the potential application perspectives analyzed in terms of burning behavior in a cone calorimetry test. Adding inorganic fillers derived from waste significantly reduces the flammability of composites with a matrix of thermoplastic polymers while increasing their sustainability and lowering their price without considerably reducing their mechanical properties, which allows for assigning developed materials as a replacement for flame-retarded polyethylene in large-scale non-loaded parts.

Development of Toughened Flax Fiber Reinforced Composites. Modification of Poly(lactic acid)/Poly(butylene adipate-co-terephthalate) Blends by Reactive Extrusion Process.

The presented study focuses on the development of flax fiber (FF) reinforced composites prepared with the use of poly(lactic acid)/poly(butylene adipate-co-terephthalate)-PLA/PBAT blend system. This type of modification was aimed to increase impact properties of PLA-based composites, which are usually characterized by high brittleness. The PLA/PBAT blends preparation was carried out using melt blending technique, while part of the samples was prepared by reactive extrusion process with the addition of chain extender (CE) in the form of epoxy-functionalized oligomer. The properties of unreinforced blends was evaluated using injection molded samples. The composite samples were prepared by compression molding technique, while flax fibers reinforcement was in the form of plain fabric. The properties of the laminated sheets were investigated during mechanical test measurements (tensile, flexural, impact). Differential scanning calorimetry (DSC) analysis was used to determine the thermal properties, while dynamic mechanical thermal analysis (DMTA) and heat deflection temperature (HDT) measurements were conducted in order to measure the thermomechanical properties. Research procedure was supplemented with structure evaluation using scanning electron microscopy (SEM) analysis. The comparative study reveals that the properties of PLA/PBAT-based composites were more favorable, especially in the context of impact resistance improvement. However, for CE modified samples also the modulus and strength was improved. Structural observations after the impact tests confirmed the presence of the plastic deformation of PLA/PBAT matrix, which confirmed the favorable properties of the developed materials. The use of PBAT phase as the impact modifier strongly reduced the PLA brittleness, while the reactive extrusion process improves the fiber-matrix interactions leading to higher stiffness and strength.

Rigid Polyurethane Foams Modified with Biochar.

This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.

Automated size-specific dose estimates using deep learning image processing.

An automated vendor-independent system for dose monitoring in computed tomography (CT) medical examinations involving ionizing radiation is presented in this paper. The system provides precise size-specific dose estimates (SSDE) following the American Association of Physicists in Medicine regulations. Our dose management can operate on incomplete DICOM header metadata by retrieving necessary information from the dose report image by using optical character recognition. For the determination of the patient's effective diameter and water equivalent diameter, a convolutional neural network is employed for the semantic segmentation of the body area in axial CT slices. Validation experiments for the assessment of the SSDE determination and subsequent stages of our methodology involved a total of 335 CT series (60 352 images) from both public databases and our clinical data. We obtained the mean body area segmentation accuracy of 0.9955 and Jaccard index of 0.9752, yielding a slice-wise mean absolute error of effective diameter below 2 mm and water equivalent diameter at 1 mm, both below 1%. Three modes of the SSDE determination approach were investigated and compared to the results provided by the commercial system GE DoseWatch in three different body region categories: head, chest, and abdomen. Statistical analysis was employed to point out some significant remarks, especially in the head category.

Development of Thermal Resistant FDM Printed Blends. The Preparation of GPET/PC Blends and Evaluation of Material Performance.

The paper discusses the preparation of polymer blends based on the polyethylene terephthalate copolymer/polycarbonate (GPET/PC). Materials have been prepared in order to assess their applicability in the fused deposition modeling (FDM) 3D printing process. The tested key feature was the thermomechanical resistance, measured by head deflection temperature (HDT) and Vicat softening temperature (VST), the mechanical tests and dynamic mechanical thermal analysis (DMTA) were also performed. A clear relationship between the increasing content of PC in the blend properties was observed. DMTA analysis revealed significant changes in the glass transition temperature, which indicates the miscibility of this type of polymer system. The mechanical tests indicate a clear trend of stiffness and strength improvement along with the increasing share of PC phase in the structure. The increase in impact strength is also clear, however, compared to the results for a pure PC, the results obtained for GPET/PC blends are significantly lower. As part of the research, reference samples based on polyethylene terephthalate homopolymer (PET) and composite samples with addition of 10% talc were also prepared. The structure analysis for PET/PC(50/50) samples did not show miscibility. However, due to the formation of the PET crystalline phase, the thermomechanical resistance of these materials was visibly higher. Scanning electron microscopy (SEM) analysis confirmed a high degree of compatibility of the GPET/PC blend structure as indicated by the lack of visible signs of phase separation. This phenomenon is not observed for PET/PC blends, which confirms the different thermomechanical interactions of both tested polymer systems.

The Influence of the Hybridization Process on the Mechanical and Thermal Properties of Polyoxymethylene (POM) Composites with the Use of a Novel Sustainable Reinforcing System Based on Biocarbon and Basalt Fiber (BC/BF).

The presented work focuses on the assessment of the material performance of polyoxymethylene (POM)-based composites reinforced with the use of a biocarbon/basalt fiber system (BC/BF). The use of BC particles was aimed at eliminating mineral fillers (chalk, talc) by using fully biobased material, while basalt fibers can be considered an alternative to glass fibers (GF). All materials were prepared with the same 20% filler content, the differences concerned the (BC/BF) % ratio. Hybrid samples with (25/75), (50/50), and (75/25) ratios were prepared. Additionally, reference samples were also prepared (POM BC20% and POM BF20%.). Samples prepared by the injection molding technique were subjected to a detailed analysis of mechanical properties (static tensile and Charpy impact tests), thermomechanical characteristics (dynamic mechanical thermal analysis-DMTA, heat deflection temperature - HDT), and thermal and rheological properties (DSC, rotational rheometer tests). In order to assess fiber distribution within the material structure, the samples were scanned by a microtomography method (µCT). The addition of even a significant amount of BC particles did not cause excessive material brittleness, while the elongation and impact strength of all hybrid samples were very similar to the reference POM BF20% sample. The tensile modulus and strength values appear to be strictly dependent on the increasing BF fiber content. Thermomechanical analysis (DMTA, HDT) showed very similar heat resistance for all hybrid samples; the results did not differ from the values for the POM BF20 sample.

Improving the Toughness and Thermal Resistance of Polyoxymethylene/Poly(lactic acid) Blends: Evaluation of Structure-Properties Correlation for Reactive Processing.

The study focuses on the development of polyoxymethylene (POM)/poly(lactic acid) (PLA) blends with increased impact and thermal resistance. The study was conducted in two phases; in the first part, a series of unmodified blends with PLA content of 25, 50, and 75 wt.% was prepared, while the second part focused on the modification of the PLA/POM (50/50) blends. An ethylene/butyl acrylate/glycidyl methacrylate terpolymer (E/BA/GMA) elastomer (EBA) was used to improve the impact strength of the prepared blends, while reactive blending was used to improve interfacial interactions. We used a multifunctional epoxy chain extender (CE) as the compatibilizer. Static tensile tests and notched Izod measurement were used to evaluate the mechanical performance of the prepared samples. The thermomechanical properties were investigated using dynamic mechanical thermal analysis (DMTA) analysis and heat deflection temperature (HDT)/Vicat softening temperature (VST) methods. The crystallinity was measured using differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXS) measurements, while the rheology was evaluated using a rotational rheometer. The paper also includes a structure analysis performed using the SEM method. The structural tests show partial miscibility of the POM/PLA systems, resulting in the perfect compatibility of both phases. The impact properties of the final blends modified by the EBA/CE system were found to be similar to pure POM resin, while the E modulus was visibly improved. Favorable changes were also noticeable in the case of the thermomechanical properties. The results of most of the conducted measurements and microscopic observations confirm the high efficiency of the reaction for PLA as well as for the modified POM/PLA mixtures.