Superconductor based, tomographic, neutron diagnostics for fusion power monitoring.

We propose a scalable system of compact, superconducting neutron monitors, which can be embedded in any existing cryogenic infrastructure of a fusion system. The pixel-based nature of the detectors allows them to be placed at intervals following the circumference of a cooled zone, e.g., a field coil, thus allowing for a tomographic measurement of the neutron flux surrounding the plasma. An early stage prototype of the superconducting bolometer is described, and the key results of a previous feasibility study of this prototype performed with cold neutrons are summarized. The bolometer can be adapted for use with fast neutrons by altering the composition and geometry of the neutron-to-heat conversion layer. This paper describes the initial feasibility considerations for implementation in a superconducting tokamak. The sensor is based on a high-temperature superconductor, making it possible to select the operation temperature in the range 1-90 K. Neutron flux numbers were found using the ITER MCNP reference model, and these were embedded in a TOPAS model to find the expected signal measured by the bolometer at the position of a toroidal field coil. The results at the coil position indicate suitable operation levels in terms of the magnitude of the measured signal, with a measurable signal of several ohm, which is much smaller than the saturation energy of the detector. Radiation hardness is estimated and found to be on the order of at least 40 years for the relevant radiation levels. The upcoming investigation activities of the project are described for both radiation testing and analytical modeling.

Giant electrocaloric materials energy efficiency in highly ordered lead scandium tantalate.

Electrocaloric materials are promising working bodies for caloric-based technologies, suggested as an efficient alternative to the vapor compression systems. However, their materials efficiency defined as the ratio of the exchangeable electrocaloric heat to the work needed to trigger this heat remains unknown. Here, we show by direct measurements of heat and electrical work that a highly ordered bulk lead scandium tantalate can exchange more than a hundred times more electrocaloric heat than the work needed to trigger it. Besides, our material exhibits a maximum adiabatic temperature change of 3.7 K at an electric field of 40 kV cm-1. These features are strong assets in favor of electrocaloric materials for future cooling devices.

Plasma Electrolytic Polishing of Nitinol: Investigation of Functional Properties.

A novel, environmentally friendly, fast, and flexible polishing process for Nitinol parts is presented in this study. Nitinol samples with both superelastic and shape memory properties at room temperature were investigated. The chemical contamination and surface roughness of superelastic Nitinol plates were examined before and after plasma electrolytic polishing. The shift in phase transformation temperature and tensile strength before and after the polishing process were analysed using Nitinol wire with shape memory properties. The obtained experimental results were compared to the data obtained on reference samples examined in the as-received condition. It was found that plasma electrolytic polishing, when the right process parameters are applied, is capable of delivering Nitinol parts with extremely high surface quality. Moreover, it was experimentally proven that plasma electrolytic polishing does not have a negative impact on functionality or mechanical properties of polished parts.

Avoided crossing of rattler modes in thermoelectric materials.

Engineering of materials with specific physical properties has recently focused on the effect of nano-sized 'guest domains' in a 'host matrix' that enable tuning of electrical, mechanical, photo-optical or thermal properties. A low thermal conductivity is a prerequisite for obtaining effective thermoelectric materials, and the challenge is to limit the conduction of heat by phonons, without simultaneously reducing the charge transport. This is named the 'phonon glass-electron crystal' concept and may be realized in host-guest systems. The guest entities are believed to have independent oscillations, so-called rattler modes, which scatter the acoustic phonons and reduce the thermal conductivity. We have investigated the phonon dispersion relation in the phonon glass-electron crystal material Ba(8)Ga(16)Ge(30) using neutron triple-axis spectroscopy. The results disclose unambiguously the theoretically predicted avoided crossing of the rattler modes and the acoustic-phonon branches. The observed phonon lifetimes are longer than expected, and a new explanation for the low kappa(L) is provided.

Interparticle interactions in agglomerates of alpha-Fe2O3 nanoparticles: influence of grinding.

We have chemically prepared a sample of antiferromagnetic alpha-Fe2O3 nanoparticles by a gel-sol technique. Mössbauer spectra of the as-prepared sample showed that superparamagnetic relaxation was suppressed due to strong magnetic interparticle interactions even at room temperature. However, subsequent grinding of the sample by hand in a mortar for some minutes resulted in fast superparamagnetic relaxation of some of the particles. The effect was even more dramatic if the alpha-Fe2O3 powder was ground for a longer time or together with nonmagnetic eta-Al2O3 nanoparticles. Similar effects were found after low-energy ball milling. Thus it is found that the agglomeration of the nanoparticles during preparation under wet conditions results in strong magnetic interparticle interaction, but a relatively gentle mechanical treatment is sufficient to break up the agglomerates, resulting in much weaker interactions. We show that these effects can also be seen when a soil sample containing magnetic nanoparticles is ground.