Catalytic disconnection of C-O bonds in epoxy resins and composites.

Fibre-reinforced epoxy composites are well established in regard to load-bearing applications in the aerospace, automotive and wind power industries, owing to their light weight and high durability. These composites are based on thermoset resins embedding glass or carbon fibres1. In lieu of viable recycling strategies, end-of-use composite-based structures such as wind turbine blades are commonly landfilled1-4. Because of the negative environmental impact of plastic waste5,6, the need for circular economies of plastics has become more pressing7,8. However, recycling thermoset plastics is no trivial matter1-4. Here we report a transition-metal-catalysed protocol for recovery of the polymer building block bisphenol A and intact fibres from epoxy composites. A Ru-catalysed, dehydrogenation/bond, cleavage/reduction cascade disconnects the C(alkyl)-O bonds of the most common linkages of the polymer. We showcase the application of this methodology to relevant unmodified amine-cured epoxy resins as well as commercial composites, including the shell of a wind turbine blade. Our results demonstrate that chemical recycling approaches for thermoset epoxy resins and composites are achievable.

Underwater Fabrication of Carbon Nanotube/Coacervate Composites.

Soft conductive materials are of interest for a wide range of applications, but their syntheses have remained difficult. Herein, we present a convenient route for underwater fabrication of a composite made of carbon nanotubes (CNTs) and mussel-inspired complex coacervates. The key to success of this method is that CNTs were solubilized very effectively in protocoacervates, which are high-concentration solutions of polyelectrolytes at a pH where only one of them is charged, thereby impeding coacervate formation. Composite materials were formed by the simple injection of CNT-dispersed protocoacervate solutions into water under ambient conditions. The method is simple, fast, and ecofriendly, and composites of CNT-complex coacervate in the form of films or bulk materials were obtained. The composites demonstrated electrical conductivity and tunable mechanical properties, which depended on the concentration of polyelectrolytes and the CNT:protocoacervate ratio. Hence, the composites can be manipulated to attain diverse properties, for examples, tunable reduced modulus (15 to 32 GPa) and hardness (0.3 to 0.7 GPa) as well as an electrical conductivity of up to 4 × 103 S m-1.

Opportunities for biomineralization research using multiscale computed X-ray tomography as exemplified by bone imaging.

Biominerals typically have complex hierarchical structures traversing many length scales. This makes their structural characterization complicated, since it requires 3D techniques that can probe full specimens at down to nanometer-resolution, a combination that is difficult - if not impossible - to achieve simultaneously. One challenging example is bone, a mineralized tissue with a highly complex architecture that is replete with a network of cells. X-ray computed tomography techniques enable multiscale structural characterization through the combination of various equipment and emerge as promising tools for characterizing biominerals. Using bone as an example, we discuss how combining different X-ray imaging instruments allow characterizing bone structures from the nano- to the organ-scale. In particular, we compare and contrast human and rodent bone, emphasize the importance of the osteocyte lacuno-canalicular network in bone, and finally illustrate how combining synchrotron X-ray imaging with laboratory instrumentation for computed tomography is especially helpful for multiscale characterization of biominerals.

Very large-scale diffraction investigations enabled by a matrix-multiplication facilitated radial and azimuthal integration algorithm: MatFRAIA.

As synchrotron facilities continue to generate increasingly brilliant X-rays and detector speeds increase, swift data reduction from the collected area detector images to more workable 1D diffractograms becomes of increasing importance. This work reports an integration algorithm that can integrate diffractograms in real time on modern laptops and can reach 10 kHz integration speeds on modern workstations using an efficient pixel-splitting and parallelization scheme. This algorithm is limited not by the computation of the integration itself but is rather bottlenecked by the speed of the data transfer to the processor, the data decompression and/or the saving of results. The algorithm and its implementation is described while the performance is investigated on 2D scanning X-ray diffraction/fluorescence data collected at the interface between an implant and forming bone.

Dual-Responsive Material Based on Catechol-Modified Self-Immolative Poly(Disulfide) Backbones.

Functional materials engineered to degrade upon triggering are in high demand due their potentially lower impact on the environment as well as their use in sensing and in medical applications. Here, stimuli-responsive polymers are prepared by decorating a self-immolative poly(dithiothreitol) backbone with pendant catechol units. The highly functional polymer is fashioned into stimuli-responsive gels, formed through pH-dependent catecholato-metal ion cross-links. The gels degrade in response to specific environmental changes, either by addressing the pH responsive, non-covalent, catecholato-metal complexes, or by addition of a thiol. The latter stimulus triggers end-to-end depolymerization of the entire self-immolative backbone through end-cap replacement via thiol-disufide exchanges. Gel degradation is visualized by release of a dye from the supramolecular gel as it itself is converted into smaller molecules.

Nanobeam X-ray fluorescence and diffraction computed tomography on human bone with a resolution better than 120 nm.

Studying nanostructured hierarchical materials such as the biomineralized bone is challenging due to their complex 3D structures that call for high spatial resolution. One route to study such materials is X-ray powder diffraction computed tomography (XRD-CT) that reveals the 3D distribution of crystalline phases and X-ray fluorescence computed tomography (XRF-CT) that provides element distributions. However, the spatial resolution of XRD-CT has thus far been limited. Here we demonstrate better than 120 nm 3D resolution on human bone in XRD-CT and XRF-CT measured simultaneously using X-ray nanobeams. The results pave the way for nanoscale 3D characterization of nanocrystalline composites like bone at unprecedented detail.

No Signature of Osteocytic Osteolysis in Cortical Bone from Lactating NMRI Mice.

The roles of osteocytes in bone homeostasis have garnered increasing attention since it has been realized that osteocytes communicate with other organs. It has long been debated whether and/or to which degree osteocytes can break down the bone matrix surrounding them in a process called osteocytic osteolysis. Osteocytic osteolysis has been indicated to be induced by a number of skeletal challenges including lactation in CD1 and C57BL/6 mice, whereas immobilization-induced osteocytic osteolysis is still a matter of controversy. Motivated by the wish to understand this process better, we studied osteocyte lacunae in lactating NMRI mice, which is a widely used outbred mouse strain. Surprisingly, no trace of osteocytic osteolysis could be detected in tibial or femoral cortical bone either by 3D investigation by synchrotron nanotomography, by studies of lacunar cross-sectional areas using scanning electron microscopy, or by light microscopy. These results lead us to conclude that osteocytic osteolysis does not occur in NMRI mice as a response to lactation, in turn suggesting that osteocytic osteolysis may not play a generic role in mobilizing calcium during lactation.

Co-incorporation of alkali metal ions during amorphous calcium carbonate precipitation and their stabilizing effect.

Calcium carbonate formation has been studied extensively due to its central role in biomineralization and geochemistry. Specifically, the effect of additives incorporated during the formation process has been described in several works related to inorganic, small organic, molecular or macromolecular additives. However, in these previous experiments the presence of counter ions and their possible role has been mostly disregarded. Co-incorporation of counter ions into calcite at low supersaturations has been studied in detail but their incorporation in and effect on the formation and stability of the amorphous phase, which precedes the formation of the crystalline phase at high supersaturations, has not been studied. To address this, we have investigated the incorporation of alkali metal ions into the amorphous phase using various carbonate salts as a carbonate source. We show that the incorporation is the highest for Rb+ with the highest measured value being 5.8 at% Rb+/(Rb+ + Ca2+). The extent of ion incorporation follows the ion size of Rb+ > K+ > Na+ > Li+ which is opposite to that observed in calcite formed at low supersaturation. The presence of these ions in the amorphous phase increases the crystallization temperature, which can be shifted by as much as 200 °C depending on the concentration of alkali metal ions incorporated. However, the lifetime of ACC in solution was similar for all the different carbonate sources.

X-ray Linear Dichroism in Apatite.

The recent observation in parrotfish teeth of X-ray linear dichroism motivated an in-depth investigation into this spectroscopic effect in various apatite crystals, including geologic hydroxyapatite (Ca5(PO4)3OH), fluorapatite (Ca5(PO4)3F), and their biogenic counterparts in human bone, mouse enamel, and in parrotfish bone, dentin, and enameloid, the equivalent of dental enamel in certain fish. These data are important because they now enable visualization of the nano- to microscale structure of apatite crystals in teeth and bone. Polarization-dependent imaging contrast (PIC) maps of lamellar bone, obtained with a new method that minimizes space-charge and charging effects, show the expected rotating apatite crystal orientations. PIC maps of mouse enamel reveal a complex arrangement of hydroxyapatite crystals perpendicular to the dentin-enamel junction, with rods arranged in a decussation pattern in inner enamel and nearly parallel to one another in outer enamel. In both inner and outer enamel crystal c-axes are not always aligned with the rod elongation direction.

Mussel-Inspired Self-Healing Double-Cross-Linked Hydrogels by Controlled Combination of Metal Coordination and Covalent Cross-Linking.

Mussel-inspired hydrogels held together by reversible catecholato-metal coordination bonds have recently drawn great attention owing to their attractive self-healing, viscoelastic and adhesive properties together with their pH-responsive nature. A major challenge in these systems is to orchestrate the degree of catechol oxidation that occurs under alkaline conditions in air and has a great impact on the aforementioned properties because it introduces irreversible covalent cross-links to the system, which stiffens the hydrogels but consume catechols needed for self-healing. Herein, we present a catechol-based hydrogel design that allows for the degree of oxidative covalent cross-linking to be controlled. Double cross-linked hydrogels with tunable stiffness are constructed by adding the oxidizable catechol analogue, tannic acid, to an oxidation-resistant hydrogel construct held together by coordination of the dihydroxy functionality of 1-(2'-carboxyethyl)-2-methyl-3-hydroxy-4-pyridinone to trivalent metal ions. By varying the amount of tannic acid, the hydrogel stiffness can be customized to a given application while retaining the self-healing capabilities of the hydrogel's coordination chemical component.

Calcium-Phosphate-Osteopontin Particles Reduce Biofilm Formation and pH Drops in in situ Grown Dental Biofilms.

This 2-period crossover study investigated the effect of calcium-phosphate-osteopontin particles on biofilm formation and pH in 48-h biofilms grown in situ. Bovine milk osteopontin is a highly phosphorylated glycoprotein that has been shown to interfere with bacterial adhesion to salivary-coated surfaces. Calcium-phosphate-osteopontin particles have been shown to reduce biofilm formation and pH drops in a 5-species laboratory model of dental biofilm without affecting bacterial viability. Here, smooth surface biofilms from 10 individuals were treated ex vivo 6 times/day for 30 min with either calcium-phosphate-osteopontin particles or sterile saline. After growth, the amount of biofilm formed was determined by confocal microscopy, and pH drops upon exposure to glucose were monitored using confocal-microscopy-based pH ratiometry. A total of 160 biofilms were analysed. No adverse effects of repeated ex vivo treatment with calcium-phosphate-osteopontin particles were observed. Particle treatment resulted in a 32% lower amount of biofilm formed (p < 0.05), but large inter-individual differences could be observed. Biofilm pH was significantly higher upon particle treatment, both shortly after the addition of glucose and after 30 min of incubation with glucose (p < 0.05). Calcium-phosphate-osteopontin particles may represent a new therapeutic approach to caries control and aim at directly targeting virulence factors involved in the caries process. Further studies are required to determine the effect of particle treatment on more acidogenic/aciduric biofilms as well as the remineralizing potential of the particles.

Internal structure of sponge glass fiber revealed by ptychographic nanotomography.

Sponge glass spicules have solicited great interest due to their mechanical and optical properties. Herein we use ptychographic nanotomography to obtain detailed insights into the internal structure of an anchor spicule from the Venus flower basket. The obtained dataset has 90nm resolution in 3D and provides quantitative determination of the electron density. The data reveal significant variations in electron density across the spicule. The central organic filament is found to be slightly but significantly displaced from the spicule central axis. Analysis of the electron density affords an estimate of a protein volume fraction in the organic filament of about 70%. In the highly mineralized part of the spicule, the electron density is seen to display circular symmetry and be neigh independent of position along the spicule long axis. Variations in the electron density beyond those included in current models of spicule mechanics are observed.

Mussel-Inspired Materials: Self-Healing through Coordination Chemistry.

Improved understanding of the underwater attachment strategy of the blue mussels and other marine organisms has inspired researchers to find new routes to advanced materials. Mussels use polyphenols, such as the catechol-containing amino acid 3,4-dihydroxyphenylalanine (DOPA), to attach to surfaces. Catechols and their analogues can undergo both oxidative covalent cross-linking under alkaline conditions and take part in coordination chemistry. The former has resulted in the widespread use of polydopamine and related materials. The latter is emerging as a tool to make self-healing materials due to the reversible nature of coordination bonds. We review how mussel-inspired materials have been made with a focus on the less developed use of metal coordination and illustrate how this chemistry can be widely to make self-healing materials.

Apatite Formation from Amorphous Calcium Phosphate and Mixed Amorphous Calcium Phosphate/Amorphous Calcium Carbonate.

Crystallization from amorphous phases is an emerging pathway for making advanced materials. Biology has made use of amorphous precursor phases for eons and used them to produce structures with remarkable properties. Herein, we show how the design of the amorphous phase greatly influences the nanocrystals formed therefrom. We investigate the transformation of mixed amorphous calcium phosphate/amorphous calcium carbonate phases into bone-like nanocrystalline apatite using in situ synchrotron X-ray diffraction and IR spectroscopy. The speciation of phosphate was controlled by pH to favor HPO4 (2-) . In a carbonate free system, the reaction produces anisotropic apatite crystallites with large aspect ratios. The first formed crystallites are highly calcium deficient and hydrogen phosphate rich, consistent with thin octacalcium phosphate (OCP)-like needles. During growth, the crystallites become increasingly stoichiometric, which indicates that the crystallites grow through addition of near-stoichiometric apatite to the OCP-like initial crystals through a process that involves either crystallite fusion/aggregation or Ostwald ripening. The mixed amorphous phases were found to be more stable against phase transformations, hence, the crystallization was inhibited. The resulting crystallites were smaller and less anisotropic. This is rationalized by the idea that a local phosphate-depletion zone formed around the growing crystal until it was surrounded by amorphous calcium carbonate, which stopped the crystallization.

Calcium-phosphate-osteopontin particles for caries control.

Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co-precipitation and designed to bind to bacteria in biofilms, impede biofilm build-up without killing the microflora, and release phosphate ions to buffer bacterial acid production if the pH decreases below 6. Analysis of biofilm formation and pH in a five-species biofilm model for dental caries showed that treatment with particles or pure osteopontin led to less biofilm formation compared to untreated controls or biofilms treated with osteopontin-free particles. The anti-biofilm effect can thus be ascribed to osteopontin. The particles also led to a slower acidification of the biofilm after exposure to glucose, and the pH always remained above 5.5. Hence, calcium-phosphate-osteopontin particles show potential for applications in caries control.

Osteocyte lacunar properties in rat cortical bone: Differences between lamellar and central bone.

Recently, the roles of osteocytes in bone maintenance have gained increasing attention. Osteocytes reside in lacunae that are interconnected by canaliculi resulting in a vast cellular network within the mineralized bone matrix. As the structure of the lacuno-canalicular network is highly connected to osteocyte function, osteocyte lacunar properties such as volume, shape, orientation, and density are now frequently reported in studies investigating osteocyte activity. Despite this increasing interest in lacunar morphometrics, many studies show a large spread in such values, suggesting a large inter-species but also inter-site variation in lacunar properties. Here, osteocyte lacunae in rat cortical bone have been studied using synchrotron radiation micro computed tomography (SR µCT) and backscattered electron (BE) microscopy. Quantitative lacunar geometric characteristics are reported based on the synchrotron radiation data, differentiating between circumferential lamellar bone and a central, more disordered bone type. From these studies, no significant differences were found in lacunar volumes between lamellar and central bone, whereas significant differences in lacunar orientation, shape and density values were observed. The 3D nature of the SR µCT data sets furthermore revealed that lacunae in central bone, which appear to be poorly aligned in transverse 2D cross sections, are in fact highly aligned along the bone long axis. These results demonstrate the importance of using 3D methods to investigate anisotropic biological materials such as bone and that the appropriate choice of subregions for high resolution imaging is not trivial.

Hierarchical tubular structures grown from the gel/liquid interface.

Three dimensional hierarchical materials are widespread in nature but are difficult to synthesize by using self-assembly/organization. Here, we employ a gel-liquid interface to obtain centimeter-long ∼100 µm diameter tubes with complex mineral wall structures that grow from the interface into solution. The gel, made from gelatin, is loaded with metal chloride salt, whereas the solution is a high pH anion source. Tubes were obtained with a range of cations (Ca(2+) , Sr(2+) , Ba(2+) , Cu(2+) , and Zn(2+) ) and anions (CO3 (2-) and PO4 (3-) ). The crystalline phases found in the tube walls corresponded to expectations from solution chemistries and phase solubilities. The growth mechanism is found to be akin to that of chemical gardens. The divalent cations modify the strength of the gelatin gel in a manner that involves not only simple electrostatic screening, but also ion-specific effects. Thus, tubes were not obtained for those ions and/or concentrations that significantly changed the gel's mechanical structure. At high Cu(2+) loading, for example, vertical convection bands, not Liesegang bands, were observed in the gels.

pH-induced metal-ligand cross-links inspired by mussel yield self-healing polymer networks with near-covalent elastic moduli.

Growing evidence supports a critical role of metal-ligand coordination in many attributes of biological materials including adhesion, self-assembly, toughness, and hardness without mineralization [Rubin DJ, Miserez A, Waite JH (2010) Advances in Insect Physiology: Insect Integument and Color, eds Jérôme C, Stephen JS (Academic Press, London), pp 75-133]. Coordination between Fe and catechol ligands has recently been correlated to the hardness and high extensibility of the cuticle of mussel byssal threads and proposed to endow self-healing properties [Harrington MJ, Masic A, Holten-Andersen N, Waite JH, Fratzl P (2010) Science 328:216-220]. Inspired by the pH jump experienced by proteins during maturation of a mussel byssus secretion, we have developed a simple method to control catechol-Fe(3+) interpolymer cross-linking via pH. The resonance Raman signature of catechol-Fe(3+) cross-linked polymer gels at high pH was similar to that from native mussel thread cuticle and the gels displayed elastic moduli (G') that approach covalently cross-linked gels as well as self-healing properties.

Phase-contrast neutron imaging compared with wave propagation and McStas simulations.

Propagation-based phase contrast, for example in the form of edge enhancement contrast, is well established within X-ray imaging but is not widely used in neutron imaging. This technique can help increase the contrast of low-attenuation samples but may confuse quantitative absorption measurements. Therefore, it is important to understand the experimental parameters that cause and amplify or dampen this effect in order to optimize future experiments properly. Two simulation approaches have been investigated, a wave-based simulation and a particle-based simulation conducted in McStas [Willendrup & Lefmann (2020). J. Neutron Res. 22, 1-16], and they are compared with experimental data. The experiment was done on a sample of metal foils with weakly and strongly neutron absorbing layers, which were measured while varying the rotation angle and propagation distance from the sample. The experimental data show multiple signals: attenuation, phase contrast and reflection. The wave model reproduces the sample attenuation and the phase peaks but it does not reproduce the behavior of these peaks as a function of rotation angle. The McStas simulation agrees better with the experimental data, as it reproduces attenuation, phase peaks and reflection, as well as the change in these signals as a function of rotation angle and distance. This suggests that the McStas simulation approach, where the particle description of the neutron facilitates the incorporation of multiple effects, is the most convenient way of modeling edge enhancement in neutron imaging.