Antibacterial and Hemolytic Activity of Antimicrobial Hydrogels Utilizing Immobilized Antimicrobial Peptides.

Antimicrobial peptides (AMPs) are viewed as potential compounds for the treatment of bacterial infections. Nevertheless, the successful translation of AMPs into clinical applications has been impeded primarily due to their low stability in biological environments and potential toxicological concerns at higher concentrations. The covalent attachment of AMPs to a material's surface has been sought to improve their stability. However, it is still an open question what is required to best perform such an attachment and the role of the support. In this work, six different AMPs were covalently attached to a long-ranged ordered amphiphilic hydrogel, with their antibacterial efficacy evaluated and compared to their performance when free in solution. Among the tested AMPs were four different versions of synthetic end-tagged AMPs where the sequence was altered to change the cationic residue as well as to vary the degree of hydrophobicity. Two previously well-studied AMPs, Piscidin 1 and Omiganan, were also included as comparisons. The antibacterial efficacy against Staphylococcus aureus remained largely consistent between free AMPs and those attached to surfaces. However, the activity pattern against Pseudomonas aeruginosa on hydrogel surfaces displayed a marked contrast to that observed in the solution. Additionally, all the AMPs showed varying degrees of hemolytic activity when in solution. This activity was entirely diminished, and all the AMPs were non-hemolytic when attached to the hydrogels.

Clinical investigation of use of an antimicrobial peptide hydrogel wound dressing on intact skin.

A material with the ability to rapidly eradicate bacteria via a contact-killing mechanism has the benefit of a more localised treatment that is easy to implement when needed to prevent or treat a bacterial infection. Here, we present an antimicrobial material based on covalently attached antimicrobial peptides (AMPs) to a soft amphiphilic hydrogel. This results in a material that exhibits an antimicrobial effect based on contact-killing. In this study, the antimicrobial efficacy of the AMP-hydrogel was investigated by observing the changes in total bioburden on the intact skin of healthy human volunteers when the AMP-hydrogel dressing was placed on the forearm for three hours. The AMP-hydrogel significantly reduced the bioburden on the skin from a mean value of 1200CFU/cm2 for the untreated skin to 23CFU/cm2. Biocompatibility evaluations of the AMP-hydrogel showed no sign of cytotoxicity, acute systemic toxicity, irritation or sensitisation, demonstrating the safety of the AMP-hydrogel as a potential wound dressing. Leachability studies confirmed no release of AMPs and that the antimicrobial effect was localised to the surface of the hydrogels, demonstrating a pure contact-killing mode of action.

Cross-linked lyotropic liquid crystal particles functionalized with antimicrobial peptides.

Antimicrobial peptides (AMPs) are promising alternatives to traditional antibiotics for addressing bacterial infections - including life-threatening antibiotic resistant infections. AMPs have a broad spectrum of antimicrobial activity and show a low probability to induce resistance. However, the poor serum stability of AMPs has limited their usage in clinical treatment. To enable improved serum stability while maintaining high antibacterial effect of AMPs, this study describes a material wherein AMPs are covalently bonded to micro-sized particles of cross-linked lyotropic liquid crystals, formed by the self-assembly of the block copolymer Pluronic F-127. The liquid crystal particles were shown to have antibacterial effect corresponding to a 4 log reduction against Staphylococcus aureus. The particles were structurally and chemically analyzed by small angle X-ray scattering, Fourier transform infra-red spectroscopy and Raman spectroscopy, confirming that the liquid crystal structure was maintained within the particles with the AMPs covalently bonded. The bonding to the particles gave the AMPs improved stability in serum, as they retained almost all of the antibacterial potency for 2 days compared to free AMPs, which lost all of its antibacterial potency within a day. Furthermore, insight regarding mode of action was obtained by cryogenic transmission electron microscopy, which showed the antimicrobial particles interacting with the surface of bacteria.

Antimicrobial Peptide-Functionalized Mesoporous Hydrogels.

Antimicrobial peptides (AMPs) are seen as a promising replacement to conventional antibiotics for the prevention of skin wound infections. However, due to the short half-life of AMPs in biological environments, such as blood, their use in clinical applications has been limited. The covalent immobilization of AMPs onto suitable substrates is an effective solution to create contact-killing surfaces with increased long-term stability. In this work, an antimicrobial peptide, RRPRPRPRPWWWW-NH2 (RRP9W4N), was covalently attached to amphiphilic and ordered mesoporous Pluronic F127 hydrogels made of cross-linked lyotropic liquid crystals through 1-ethyl-3-(3-(dimethylamino)propyl) carbodiimide (EDC) and N-hydroxysuccinimide (NHS) chemistry. The AMP-hydrogels showed high antibacterial activity against Staphylococcus epidermidis, Staphylococcus aureus, Pseudomonas aeruginosa, methicillin-resistant S. aureus (MRSA), and multidrug-resistant Escherichia coli for up to 24 h. Furthermore, the AMP-hydrogels did not present any toxicity to human fibroblasts. The AMPs retained their antimicrobial activity up to 48 h in human blood serum, which is a significant increase in stability compared to when used in dissolved state. A pilot in vivo rat model showed 10-100× less viable counts of S. aureus on AMP-hydrogels compared with control hydrogels during the first 3 days of infection. Studies performed on human whole blood showed that blood coagulated more readily in the presence of AMP-hydrogels as compared to hydrogels without AMPs, indicating potential hemostatic activity. Overall, the results suggest that the combination of amphiphilic hydrogels with covalently bonded AMPs has potential to be used as antibacterial wound dressing material to reduce infections and promote hemostatic activity as an alternative to antibiotics or other antimicrobial agents, whose use should be restricted.

Tough Ordered Mesoporous Elastomeric Biomaterials Formed at Ambient Conditions.

Synthetic dry elastomers are randomly cross-linked polymeric networks with isotropic and unordered higher-level structural features. However, their growing use as soft-tissue biomaterials has demanded the need for an ordered and anisotropic nano-micro (or) mesoarchitecture, which is crucial for imparting specific properties such as hierarchical toughening, anisotropic mechanics, sustained drug delivery, and directed tissue growth. High processing cost, poor control in 3D, and compromised mechanical properties have made it difficult to synthesize tough and dry macroscopic elastomers with well-organized nano-microstructures. Inspired from biological design principles, we report a tough ordered mesoporous elastomer formed via bottom-up lyotropic self-assembly of noncytotoxic, polymerizable amphiphilic triblock copolymers and hydrophobic polymers. The elastomer is cross-linked using covalent cross-links and physical hydrophobic entanglements that are organized in a periodic manner at the nanoscale. This transforms into a well-ordered hexagonal arrangement of nanofibrils that are highly oriented at the micron scale, further organized as 3D macroscale objects. The ordered nano-microstructure and molecular multinetwork endows the elastomer with hierarchical toughening while possessing excellent stiffness and elongation comparable to engineering elastomers like silicone and vulcanized rubber. Processing of the elastomer is performed at ambient conditions using 3D printing and photo-cross-linking, which is fast and energy efficient and enables production of complex 3D objects with tailorable sub-millimeter features such as macroporosity. Furthermore, the periodic and amphiphilic nanostructure permits functionalization of the elastomer with secondary components such as inorganic nanoparticles or drug molecules, enabling complementary mechanical properties such as high stiffness and functional capabilities such as in localized drug delivery applications.