Spin-Coated Polysaccharide-Based Multilayered Freestanding Films with Adhesive and Bioactive Moieties.

Freestanding films based on catechol functionalized chitosan (CHI), hyaluronic acid (HA), and bioglass nanoparticles (BGNPs) were developed by spin-coating layer-by-layer assembly (SA-LbL). The catechol groups of 3,4-dihydroxy-l-phenylalanine (DOPA) present in the marine mussels adhesive proteins (MAPs) are the main factors responsible for their characteristic strong wet adhesion. Then, the produced films were cross-linked with genipin to improve their stability in wet state. Overall, the incorporation of BGNPs resulted in thicker and bioactive films, hydrophilic and rougher surfaces, reduced swelling, higher weight loss, and lower stiffness. The incorporation of catechol groups onto the films showed a significant increase in the films' adhesion and stiffness, lower swelling, and weight loss. Interestingly, a synergetic effect on the stiffness increase was observed upon the combined incorporation of BGNPs with catechol-modified polymers, given that such films were the stiffest. Regarding the biological assays, the films exhibited no negative effects on cellular viability, adhesion, and proliferation, and the BGNPs seemed to promote higher cellular metabolic activity. These bioactive LbL freestanding films combine enhanced adhesion with improved mechanical properties and could find applications in the biomedical field, such as guided hard tissue regeneration membranes.

Erratum: Moreira, J., et al., Spin-Coated Polysaccharide-Based Multilayered Freestanding Films with Adhesive and Bioactive Moieties. Molecules 2020, 25, 840.

The authors wish to make changes to the published paper [...].

Tailored Biodegradable and Electroactive Poly(Hydroxybutyrate-Co-Hydroxyvalerate) Based Morphologies for Tissue Engineering Applications.

Polymer-based piezoelectric biomaterials have already proven their relevance for tissue engineering applications. Furthermore, the morphology of the scaffolds plays also an important role in cell proliferation and differentiation. The present work reports on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV), a biocompatible, biodegradable, and piezoelectric biopolymer that has been processed in different morphologies, including films, fibers, microspheres, and 3D scaffolds. The corresponding magnetically active PHBV-based composites were also produced. The effect of the morphology on physico-chemical, thermal, magnetic, and mechanical properties of pristine and composite samples was evaluated, as well as their cytotoxicity. It was observed that the morphology does not strongly affect the properties of the pristine samples but the introduction of cobalt ferrites induces changes in the degree of crystallinity that could affect the applicability of prepared biomaterials. Young's modulus is dependent of the morphology and also increases with the addition of cobalt ferrites. Both pristine and PHBV/cobalt ferrite composite samples are not cytotoxic, indicating their suitability for tissue engineering applications.

Nanostructured polymeric coatings based on chitosan and dopamine-modified hyaluronic acid for biomedical applications.

In a marine environment, specific proteins are secreted by mussels and used as a bioglue to stick to a surface. These mussel proteins present an unusual amino acid 3,4-dihydroxyphenylalanine (known as DOPA). The outstanding adhesive properties of these materials in the sea harsh conditions have been attributed to the presence of the catechol groups present in DOPA. Inspired by the structure and composition of these adhesive proteins, dopamine-modified hyaluronic acid (HA-DN) prepared by carbodiimide chemistry is used to form thin and surface-adherent dopamine films. This conjugate was characterized by distinct techniques, such as nuclear magnetic resonance and ultraviolet spectrophotometry. Multilayer films are developed based on chitosan and HA-DN to form polymeric coatings using the layer-by-layer methodology. The nanostructured films formation is monitored by quartz crystal microbalance. The film surface is characterized by atomic force microscopy and scanning electron microscopy. Water contact angle measurements are also conducted. The adhesion properties are analyzed showing that the nanostructured films with dopamine promote an improved adhesion. In vitro tests show an enhanced cell adhesion, proliferation and viability for the biomimetic films with catechol groups, demonstrating their potential to be used in distinct biomedical applications.

Nanoparticle size and concentration dependence of the electroactive phase content and electrical and optical properties of Ag/poly(vinylidene fluoride) composites.

This paper describes the processing of silver-nanoparticle-doped poly(vinylidene fluoride). The effects of the concentration and size of the filler on the electroactive phase of the polymer and the optical and electrical properties are discussed. Spherical silver nanoparticles incorporated into the poly(vinylidene fluoride) polymeric matrix induce nucleation of the electroactive γ phase. The electroactive phase content strongly depends on the content and size of the nanoparticles. In particular, there is a critical nanoparticle size, below which the filler losses its nucleation efficiency due to its small size relative to that of the polymer macromolecules. Furthermore, the presence of surface plasmon resonance absorption in the composites is observed, which once again shows a strong dependence on the concentration and size of the particles. The absorption is larger for higher concentrations, and for a given concentration increases with particle size. This behavior is correlated to the electrical response and is related to the extra bands and electrons provided by the nanoparticles in the large energy band gap of the polymer.

Towards All-Non-Vacuum-Processed Photovoltaic Systems: A Water-Based Screen-Printed Cu(In,Ga)Se2 Photoabsorber with a 6.6% Efficiency.

During the last few decades, major advances have been made in photovoltaic systems based on Cu(In,Ga)Se2 chalcopyrite. However, the most efficient photovoltaic cells are processed under high-energy-demanding vacuum conditions. To lower the costs and facilitate high-throughput production, printing/coating processes are proving to be effective solutions. This work combined printing, coating, and chemical bath deposition processes of photoabsorber, buffer, and transparent conductive layers for the development of solution-processed photovoltaic systems. Using a sustainable approach, all inks were formulated using water and ethanol as solvents. Screen printing of the photoabsorber on fluorine-doped tin-oxide-coated glass followed by selenization, chemical bath deposition of the cadmium sulfide buffer, and final sputtering of the intrinsic zinc oxide and aluminum-doped zinc oxide top conductive layers delivered a 6.6% maximum efficiency solar cell, a record for screen-printed Cu(In,Ga)Se2 solar cells. On the other hand, the all-non-vacuum-processed device with spray-coated intrinsic zinc-oxide- and tin-doped indium oxide top conductive layers delivered a 2.2% efficiency. The given approaches represent relevant steps towards the fabrication of sustainable and efficient Cu(In,Ga)Se2 solar cells.

Cerebrospinal fluid hypotension following fall in a child: Case report.

CSF hypotension arises in the context of a leak of CSF which causes negative intracranial pressure. Sacral fractures result from high-energy trauma which are frequently underdiagnosed. A ten-year-old boy presented with hip pain, after a fall. He mobilized both lower limbs, reported no leg pain, irradiation nor lack of sphincter control. The neurological examination was normal. When asked to stand, he began biparietal headache, nausea and vomiting, which improved laying down. CT scan showed an occult intrasacral meningocele; the MRI revealed collections of CSF along the spine, a S3 fracture with potential laceration of the meningocele and opening of a CSF fistula. Our diagnosis was the CSF hypotension, secondary to the fistula opening. The diagnosis was challenging. The child first presented with symptoms of CSF hypotension without evident cause. The discovery of the meningocele led us to hypothesize the opening of a fistula, a rare diagnosis, later confirmed by MRI.

Eco-friendly and cost-efficient inks for screen-printed fabrication of copper indium gallium diselenide photoabsorber thin films.

Given the societal concerns about the use of toxic chemicals and costly fabrication of functional materials and devices for photovoltaic applications, it is important to develop alternative sustainable methodologies. Previous studies have shown that cost-effective printing fabrication of Cu(In,Ga)Se2 thin film photovoltaics represents an interesting alternative to energy-demanding vacuum-based deposition methods, commonly used to produce Cu(In,Ga)Se2 photovoltaics. To enrich the field of printed Cu(In,Ga)Se2 photoabsorber thin films and to develop associated eco-friendly solutions, two novel inks, consisting of non-toxic reagents and readily available oxide materials, are reported. Screen printing of the inks over fluorine-doped tin oxide conductive substrates followed by swift selenization of the resultant patterns provides a straightforward route to phase-pure, uniform, and compact Cu(In,Ga)Se2 films with thickness and band gap energies ranging from 2.5 µm to 3.5 µm and from 0.97 eV to 1.08 eV, respectively. The present approach represents an important step forward in the sustainable fabrication of Cu(In,Ga)Se2 photovoltaics, where the physical properties of the photoabsorber can be easily adjusted by tuning the conditions of the screen printing process and the metal ratios in the inks.

Cerebrospinal fluid hypotension following fall in a child: Case report.

CSF hypotension arises in the context of a leak of CSF which causes negative intracranial pressure. Sacral fractures result from high-energy trauma which are frequently underdiagnosed. A ten-year-old boy presented with hip pain, after a fall. He mobilized both lower limbs, reported no leg pain, irradiation nor lack of sphincter control. The neurological examination was normal. When asked to stand, he began biparietal headache, nausea and vomiting, which improved laying down. CT scan showed an occult intrasacral meningocele; the MRI revealed collections of CSF along the spine, a S3 fracture with potential laceration of the meningocele and opening of a CSF fistula. Our diagnosis was the CSF hypotension, secondary to the fistula opening. The diagnosis was challenging. The child first presented with symptoms of CSF hypotension without evident cause. The discovery of the meningocele led us to hypothesize the opening of a fistula, a rare diagnosis, later confirmed by MRI.

Large-scale aqueous synthesis of Cu(In,Ga)Se2 nanoparticles for photocatalytic degradation of ciprofloxacin.

Environmentally friendly synthesis of Cu(In,Ga)Se2 (CIGS) nanoparticles (NPs) is pivotal for producing sustainable photocatalytic compounds to be applied in the remediation of contaminants of emerging concern from water. To this end, we herein report an aqueous synthesis of CIGS NPs, followed by annealing, to give access to phase-pure CIGS crystals with chalcopyrite structure and no signs of secondary phases. Morphological and compositional characterization revealed NPs with an average size of 10-35 nm and uniform distribution of Cu, In, Ga, and Se elements. In addition, the first aqueous large-scale synthesis of CIGS NPs is developed by up-scaling the synthesis procedure, resulting in 5 g of highly crystalline nanoparticles exhibiting an ideal optical band gap of 1.14 eV. The as-synthesized NPs proved the ability to remove 71 and 83% of a contaminant of emerging concern, ciprofloxacin (CIP), under ultraviolet (UV) and visible (Vis) radiations, respectively.

Effect of Polymer Dissolution Temperature and Conditioning Time on the Morphological and Physicochemical Characteristics of Poly(Vinylidene Fluoride) Membranes Prepared by Non-Solvent Induced Phase Separation.

This work reports on the production of poly(vinylidene fluoride) (PVDF) membranes by non-solvent induced phase separation (NIPS) using N,N-dimethylformamide (DMF) as solvent and water as non-solvent. The influence of the processing conditions in the morphology, surface characteristics, structure, thermal and mechanical properties were evaluated for polymer dissolution temperatures between 25 and 150 °C and conditioning time between 0 and 10 min. Finger-like pore morphology was obtained for all membranes and increasing the polymer dissolution temperature led to an increase in the average pore size (≈0.9 and 2.1 µm), porosity (≈50 to 90%) and water contact angle (up to 80°), in turn decreasing the ß PVDF content (≈67 to 20%) with the degree of crystallinity remaining approximately constant (≈56%). The conditioning time did not significantly affect the polymer properties studied. Thus, the control of NIPS parameters proved to be suitable for tailoring PVDF membrane properties.

Large-Scale Synthesis of Semiconducting Cu(In,Ga)Se2 Nanoparticles for Screen Printing Application.

During the last few decades, the interest over chalcopyrite and related photovoltaics has been growing due the outstanding structural and electrical properties of the thin-film Cu(In,Ga)Se2 photoabsorber. More recently, thin film deposition through solution processing has gained increasing attention from the industry, due to the potential low-cost and high-throughput production. To this end, the elimination of the selenization procedure in the synthesis of Cu(In,Ga)Se2 nanoparticles with following dispersion into ink formulations for printing/coating deposition processes are of high relevance. However, most of the reported syntheses procedures give access to tetragonal chalcopyrite Cu(In,Ga)Se2 nanoparticles, whereas methods to obtain other structures are scarce. Herein, we report a large-scale synthesis of high-quality Cu(In,Ga)Se2 nanoparticles with wurtzite hexagonal structure, with sizes of 10-70 nm, wide absorption in visible to near-infrared regions, and [Cu]/[In + Ga] ≈ 0.8 and [Ga]/[Ga + In] ≈ 0.3 metal ratios. The inclusion of the synthesized NPs into a water-based ink formulation for screen printing deposition results in thin films with homogenous thickness of ≈4.5 µm, paving the way towards environmentally friendly roll-to-roll production of photovoltaic systems.

Degradation studies of transparent conductive electrodes on electroactive poly(vinylidene fluoride) for uric acid measurements.

Biochemical analysis of physiological fluids using, for example, lab-on-a-chip devices requires accurate mixing of two or more fluids. This mixing can be assisted by acoustic microagitation using a piezoelectric material, such as the ß-phase of poly(vinylidene fluoride) (ß-PVDF). If the analysis is performed using optical absorption spectroscopy and ß-PVDF is located in the optical path, the material and its conductive electrodes must be transparent. Moreover, if, to improve the transmission of the ultrasonic waves to the fluids, the piezoelectric transducer is placed inside the fluidic structures, its degradation must be assessed. In this paper, we report on the degradation properties of transparent conductive oxides, namely, indium tin oxide (ITO) and aluminum-doped zinc oxide, when they are used as electrodes for providing acoustic microagitation. The latter promotes mixing of chemicals involved in the measurement of uric acid concentration in physiological fluids. The results are compared with those for aluminum electrodes. We find that ß-PVDF samples with ITO electrodes do not degrade either with or without acoustic microagitation.

Physicochemical stability of contact lenses materials for biomedical applications.

PURPOSE: The physicochemical stability, thermal and water plasticizing effect on transport properties of contact lenses (CL) were analyzed to verify its capacity to maintain the original properties after being dehydrated and rehydrated. METHODS: Two daily disposable (nesofilcon A and delefilcon A) and two monthly CL (comfilcon A and lotrafilcon B) were used. Measurements of refractive index (RI), water content (WC), chemical structure and thermal properties were taken: new (N), after dehydration (D) and rehydrated (R). RI and WC were accessed using a digital automated refractometer (CLR-12-70). Chemical structure was evaluated by a Fourier Transformed Infrared Spectroscopy (FTIR-ATR) and Differential Scanning Calorimetry (DSC) with a calorimeter (Mettler Toledo DSC-821). RESULTS: The FTIR spectrum of N, D and R was quite similar for all CL, with higher differences observed in the transmission between 3500-3000cm-1 due to the hydroxyl group (OH). After dehydration and rehydration, there were no significant changes in the chemical structure. RI and WC of the CL rehydrated did not vary significantly from the initial CL (p>0.05) and thermal properties also confirm that the behavior did not change. It was observed that the glass-transition temperature decrease with increased WC. CONCLUSION: No significant alterations were observed in the physicochemical structure of the materials after dehydration and rehydration showing a good stability of their components. The strong water plasticizing effect in the silicone hydrogel lens materials improves flexibility and chain mobility and may should be considered for other biomedical applications.

Biodegradable Hydrogels Loaded with Magnetically Responsive Microspheres as 2D and 3D Scaffolds.

Scaffolds play an essential role in the success of tissue engineering approaches. Their intrinsic properties are known to influence cellular processes such as adhesion, proliferation and differentiation. Hydrogel-based matrices are attractive scaffolds due to their high-water content resembling the native extracellular matrix. In addition, polymer-based magnetoelectric materials have demonstrated suitable bioactivity, allowing to provide magnetically and mechanically activated biophysical electrical stimuli capable of improving cellular processes. The present work reports on a responsive scaffold based on poly (L-lactic acid) (PLLA) microspheres and magnetic microsphere nanocomposites composed of PLLA and magnetostrictive cobalt ferrites (CoFe2O4), combined with a hydrogel matrix, which mimics the tissue's hydrated environment and acts as a support matrix. For cell proliferation evaluation, two different cell culture conditions (2D and 3D matrices) and two different strategies, static and dynamic culture, were applied in order to evaluate the influence of extracellular matrix-like confinement and the magnetoelectric/magneto-mechanical effect on cellular behavior. MC3T3-E1 proliferation rate is increased under dynamic conditions, indicating the potential use of hydrogel matrices with remotely stimulated magnetostrictive biomaterials for bone tissue engineering.

Erratum: Development of Poly(l-Lactic Acid)-Based Bending Actuators. Polymers 2020, 12, 1187.

The authors wish to make a change to their published paper [...].

Morphology Dependence Degradation of Electro- and Magnetoactive Poly(3-hydroxybutyrate-co-hydroxyvalerate) for Tissue Engineering Applications.

Poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is a piezoelectric biodegradable and biocompatible polymer suitable for tissue engineering applications. The incorporation of magnetostrictive cobalt ferrites (CFO) into PHBV matrix enables the production of magnetically responsive composites, which proved to be effective in the differentiation of a variety of cells and tissues. In this work, PHBV and PHBV with CFO nanoparticles were produced in the form of films, fibers and porous scaffolds and subjected to an experimental program allowing to evaluate the degradation process under biological conditions for a period up to 8 weeks. The morphology, physical, chemical and thermal properties were evaluated, together with the weight loss of the samples during the in vitro degradation assays. No major changes in the mentioned properties were found, thus proving its applicability for tissue engineering applications. Degradation was apparent from week 4 and onwards, leading to the conclusion that the degradation ratio of the material is suitable for a large range of tissue engineering applications. Further, it was found that the degradation of the samples maintain the biocompatibility of the materials for the pristine polymer, but can lead to cytotoxic effects when the magnetic CFO nanoparticles are exposed, being therefore needed, for magnetoactive applications, to substitute them by biocompatible ferrites, such as an iron oxide (Fe3O4).

Development of Poly(l-Lactic Acid)-Based Bending Actuators.

This work reports on the development of bending actuators based on poly(l-lactic acid) (PLLA)/ionic liquid (IL) blends, through the incorporation of 40% wt. of the 1-ethyl-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][TFSI]) IL. The films, obtained by solvent casting at room temperature and 50 °C, were subjected to several post-thermal treatments at 70, 90, 120 and 140 °C, in order to modify the crystallinity of the films. The influence of the drying temperature and of [Emim][TFSI] blending on the morphological, structural, mechanical and electrical properties of the composite materials were studied. The IL induced the formation of a porous surface independently of the processing conditions. Moreover, the [Emim][TFSI] dopant and the post-thermal treatments at 70 °C promoted an increase of the degree of crystallinity of the samples. No significant changes were observed in the degree of crystallinity and Young Modulus for samples with thermal treatment between 70 and 140 °C. The viability of the developed high ionic conductive blends for applications as soft actuators was evaluated. A maximum displacement of 1.7 mm was achieved with the PLLA/[Emim][TFSI] composite prepared at 50 °C and thermally treated at 140 °C, for an applied voltage of 10 Vpp, at a frequency of 100 mHz. This work highlights interesting avenues for the use of PLLA in the field of actuators.

Drug therapy and other factors associated with the development of acute kidney injury in critically ill patients: a cross-sectional study.

BACKGROUND: Acute kidney injury (AKI) is associated with a significant increase in morbidity, mortality, and health care costs. In intensive care units (ICU), AKI is commonly multifactorial and frequently involves diverse factors, such as hypovolemia, sepsis, and the use of nephrotoxic drugs. We aimed to investigate drug therapy and other factors associated with the development of AKI in a Brazilian public hospital. METHODS: This is a cross-sectional study involving critically ill patients at an ICU of a tertiary hospital. All data on sequential serum creatinine (SCr) level, glomerular filtration rate (GFR), and urine output were collected during ICU stay. The primary outcome was the occurrence of AKI assessed by the Acute Kidney Injury Network (AKIN) criterion. Sociodemographics, clinical data and drug therapy were considered as covariates. Factors associated with AKI were assessed using logistic regression. RESULTS: Overall, 122 participants were included in the study. Median age was 46.0 (interquartile range, IQ = 29.0-69.0) years, with a predominance of men (58.2%). Mean number of prescribed drugs throughout ICU stay was 22.0 ± 9.4. The number of potentially nephrotoxic drugs ranged from two to 24 per patient. A total of 29 (23.8%) ICU patients developed AKI. In the AKI-group, patients were older and showed higher Acute Physiology and Chronic Health Evaluation II (APACHE II) scores at admission, higher rates of sedation, mechanical ventilation, and infection. More drugs in general and specifically more vasoactive drugs were prescribed for AKI group. Patients who developed AKI tended to have extended stays in the ICU and a lower probability of being discharged alive than patients with no AKI development. Model adjustments of logistic regression showed that the number of medications (OR 1.15; 95% CI [1.05-1.27]) was the only factor associated with AKI in this study. This association was independent of drug nephrotoxicity. DISCUSSION: Intensive care is characterized by its complexity that combines unstable patients, severe diseases, high density of medical interventions, and drug use. We found that typical risk factors for AKI showed statistical association on bivariate analysis. The contribution of drug therapy in the occurrence of AKI in medical ICUs reinforces the need for prevention strategies focused on early recognition of renal dysfunction and interventions in drug therapy. These actions would help improve the quality of patient care and ensure progress towards medication safety.