Fabrication of 3D metal dot arrays by geometrically structured dynamic shadowing lithography.

Sphere lithography (SL), sometimes erroneously generalized as nanosphere lithography (NSL), stands out as a versatile technique capable of producing 2D periodic micro- and nanostructures with general materials applicability, flexible size and shape control, high throughput, and elegance of simplicity. Many of the fundamental aspects of the features produced by SL have been investigated in a systematic manner, including the optical, magnetic, electronic, and catalytic behaviors with emphasis toward applications in biosensing, ultrasensitive spectroscopy, and nanodevice fabrication. Previous work has primarily focused on two-dimensional patterning, however, with little attention paid to vertical growth of the SL features. In this work, the 3D structural evolution of metal dot arrays at two different length scales was demonstrated by SL-based geometrically structured dynamic shadowing lithography (GSDSL). An empirically derived model of structural growth is also developed to predict the shape and size of the features in this system.

Motion analysis of self-propelled Pt-silica particles in hydrogen peroxide solutions.

Silica microspheres that are half-coated with platinum metal undergo self-propulsion in solutions of H(2)O(2), with the average speed increasing with increasing H(2)O(2) concentration. Microscopic observation of the particle motion, with segmentation of the image data, demonstrates that the particles move, on average, with the platinum-coated region oriented opposite to the direction of motion. Velocity autocorrelation and motion direction analyses show that the direction of motion is highly correlated with the particle orientation. The effect of the observation time interval on the measured translational diffusion coefficient and the apparent particle motion is analyzed.

Ligament cells stretch-adapted on a microgrooved substrate increase intercellular communication in response to a mechanical stimulus.

An in vitro model was used to investigate the effect of mechanical stimuli on adaptation to load and calcium signaling in aligned medial collateral ligament cells (MCL). This model used a patterned silicone membrane to align the cells parallel with the direction of the microgrooves. Alignment created an architecture that simulated a degree of cell orientation in native ligament tissue. It was hypothesized that aligned ligament cells would be more efficient at calcium wave propagation than cells that were randomly oriented. It was further hypothesized that calcium wave propagation would be greater among cells that were both aligned and subjected to mechanical stretch compared to cells that were aligned but not stretched. Rat MCL cells were loaded with Fura-2AM, a calcium-binding dye, and mechanically indented using a micropipette tip. A ratio-imaging fluorescence technique was used to quantitate the calcium (Ca2+) response. It was concluded that stretching ligament cells prior to stimulation increased their sensitivity to load and their ability to propagate a calcium wave. However, the ability of aligned cells to propagate this wave was not significantly different when compared to nonaligned cells. Treatment of cultures with inhibitors such as apyrase and suramin significantly reduced the number of cells recruited in the calcium response. Hence, it was concluded that ATP released from mechanically stimulated cells was a principal mediator responsible for the rise in intracellular calcium in ligament cells. Further, purinoceptor activation may amplify the signal to alert and recruit more cells in a response to mechanical stimulation.

The genesis of molecular electronics.

Molecular electronics is, relatively speaking, a young field. Even so, there have been many significant advances and a much greater understanding of the types of materials that will be useful in molecular electronics, and their properties. The purpose of this review is to provide a broad basis for understanding the areas where new advances might arise, and to provide introduction to the subdisciplines of molecular electronics. This review is divided into two major parts; an historical examination of the development of conventional electronics, which should provide some understanding of the push towards molecular electronics. The problems associated with continuing to shrink conventional systems are presented, along with references to some of the efforts to solve them. This section is followed by an in-depth look at the most important research into the types of behaviors that molecular systems have been found to display.

Traveling-wave electrophoresis for microfluidic separations.

Models and microfluidic experiments are presented of an electrophoretic separation technique in which charged particles whose mobilities exceed a tunable threshold are trapped between the crests of a longitudinal electric wave traveling through a stationary viscous fluid. The wave is created by applying periodic potentials to electrode arrays above and below a microchannel. Predicted average velocities agree with experiments and feature chaotic attractors for intermediate mobilities.

Magnetically actuated nanorod arrays as biomimetic cilia.

We present a procedure for producing high-aspect-ratio cantilevered micro- and nanorod arrays of a PDMS-ferrofluid composite material. The rods have been produced with diameters ranging from 200 nm to 1 mum and aspect ratios as high as 125. We demonstrate actuation of these superparamagnetic rod arrays with an externally applied magnetic field from a permanent magnet and compare this actuation with a theoretical energy-minimization model. The structures produced by these methods may be useful in microfluidics, photonic, and sensing applications.