Charge Detection Mass Spectrometry for Megadalton Polymer Characterization and Measurement of Electrospray-Generated Charged Droplet Dynamics with a New "Direct Visualization of the Rayleigh Limit" Approach to Aid in m/z Calibration.

A charge detector has been constructed and mounted inside the vacuum housing of a commercial mass spectrometer (Micromass-Waters Quattro I, Waters Corp., Manchester, UK). The in-house built single-pass charge detector is composed of a designed, complete electronics system that includes a low-noise charge amplifier. Communication to the data acquisition system was enabled, and analog and digital filters were devised, followed by their tuning and programming. Data treatment scripts for data analysis and plotting were automated, and the assembled system was calibrated and tested. The instrument has an acquisition speed of ∼200 detection events/s, and it permits detection down to ∼510 charges (= three times RMS noise) for a single measured particle. The charge detector was employed to determine the oligomer distribution of a megadalton polymer, polyethylene glycol (PEG). The PEG size distribution exhibits a maximum at ∼ m/z 5910 with the oligomeric population mass distribution peaking near 4.45 MDa. In studies of methanol droplet dynamics, "charge vs time-of-flight" plots enabled clear visualization of the zone near the Rayleigh limit to droplet charging. The highest population of methanol droplets near the Rayleigh limit carried 5000-7000 charges. This corresponds to droplet weights of 10-20 GDa, with the high-end tail extending above 70 GDa. This visualization of the most highly charged droplets (that bear numbers of charges near those defined by the Rayleigh equation) was exploited as a calibration aid for our charge detector, which lacks a means of precisely defining ion energy. A maximum m/z error of -12.3% was calculated for the method, i.e., less than the potential error in assigning the true level of charging of the most highly charged droplets relative to the Rayleigh limit. With these limitations in mind, the introduced method will provide a new means for aiding the calibration of m/z values in charge detectors.

TUTORIAL: ION ACTIVATION IN TANDEM MASS SPECTROMETRY USING ULTRA-HIGH RESOLUTION INSTRUMENTATION.

Tandem mass spectrometry involves isolation of specific precursor ions and their subsequent excitation through collision-, photon-, or electron-mediated activation techniques in order to induce unimolecular dissociation leading to formation of fragment ions. These powerful ion activation techniques, typically used in between mass selection and mass analysis steps for structural elucidation, have not only found a wide variety of analytical applications in chemistry and biology, but they have also been used to study the fundamental properties of ions in the gas phase. In this tutorial paper, a brief overview is presented of the theories that have been used to describe the activation of ions and their subsequent unimolecular dissociation. Acronyms of the presented techniques include CID, PQD, HCD, SORI, SID, BIRD, IRMPD, UVPD, EPD, ECD, EDD, ETD, and EID. The fundamental principles of these techniques are discussed in the context of their implementation on ultra-high resolution tandem mass spectrometers. © 2020 John Wiley & Sons Ltd. Mass Spec Rev.

CpeF is the bilin lyase that ligates the doubly linked phycoerythrobilin on ß-phycoerythrin in the cyanobacterium Fremyella diplosiphon.

Phycoerythrin (PE) is a green light-absorbing protein present in the light-harvesting complex of cyanobacteria and red algae. The spectral characteristics of PE are due to its prosthetic groups, or phycoerythrobilins (PEBs), that are covalently attached to the protein chain by specific bilin lyases. Only two PE lyases have been identified and characterized so far, and the other bilin lyases are unknown. Here, using in silico analyses, markerless deletion, biochemical assays with purified and recombinant proteins, and site-directed mutagenesis, we examined the role of a putative lyase-encoding gene, cpeF, in the cyanobacterium Fremyella diplosiphon. Analyzing the phenotype of the cpeF deletion, we found that cpeF is required for proper PE biogenesis, specifically for ligation of the doubly linked PEB to Cys-48/Cys-59 residues of the CpeB subunit of PE. We also show that in a heterologous host, CpeF can attach PEB to Cys-48/Cys-59 of CpeB, but only in the presence of the chaperone-like protein CpeZ. Additionally, we report that CpeF likely ligates the A ring of PEB to Cys-48 prior to the attachment of the D ring to Cys-59. We conclude that CpeF is the bilin lyase responsible for attachment of the doubly ligated PEB to Cys-48/Cys-59 of CpeB and together with other specific bilin lyases contributes to the post-translational modification and assembly of PE into mature light-harvesting complexes.

Identification of Postblast Residues by DART-High Resolution Mass Spectrometry Combined with Multivariate Statistical Analysis of the Kendrick Mass Defect.

The coupling of an atmospheric pressure ionization source (Direct Analysis in Real Time, DART) and a high-resolution mass spectrometer (Orbitrap) has enabled the rapid and efficient analysis of a variety of energetic formulations. This approach was used to generate mass spectra for 83 plastic explosives and polymer samples in less than 2 min per sample. To manually interpret and identify all of the constituent polymers and other interesting features in the acquired mass spectra is a tedious and time-consuming challenge. Instead, a methodology based on the systematic calculation of Kendrick mass defects (KMDs) was developed and implemented. Its application allowed the identification of the polymeric support present in each energetic formulation. The presence of polyisobutylene in PG2 has been confirmed thanks to this approach, and a mixture of polyisobutylene, polybutadiene, and polystyrene has been confirmed in the Semtex 10 formulation. The developed methodology has also permitted the observation of changes that occur to the polymeric composition of these formulations after a blast. It appears that the most adequate way to describe post blast polymer samples is that they are less oxygenated and, above all, more unsaturated than the original starting material. These conclusions were deduced with the aid of principal component analysis, which served to establish the main factors that differentiate the samples.

Characterization of Fluorinated Polymers by Atmospheric-Solid-Analysis-Probe High-Resolution Mass Spectrometry (ASAP/HRMS) Combined with Kendrick-Mass-Defect Analysis.

Fluorinated polymers are a diverse and important class of polymers with unique applications. However, characterization of fluorinated polymers by conventional mass spectrometric methods is challenging because (i) their high fluorine contents make them insoluble or only sparingly soluble in most common solvents and (ii) commonly used matrices employed for MALDI do not desorb or ionize them efficiently. In this work, atmospheric-solid-analysis-probe (ASAP) high-resolution orbitrap mass spectrometry (HRMS) was used as a new tool for the molecular characterization of various fluorinated polymers, including polyvinylidene fluoride (PVDF) and fluorinated copolymers containing PVDF and chlorotrifluoroethylene (KEL-F 800) or PVDF and hexafluoropropylene (Viton A and Tecnoflon). The major peaks of the observed distributions were assigned compositions, but the high number of species required the use of an alternative method to treat such complex data. Kendrick-mass defects (KMD) were calculated on the basis of the "common-to-all" vinylidene difluoride repeating unit. By plotting the KMD as a function of the nominal Kendrick masses (NKM), specific patterns based on homologous series emerged. Kendrick maps were therefore drawn to simplify the mass spectra and provide confident peak assignments through homologous-series recognition. A specific fingerprint for each polymer has been identified, and the ability to discern the four species present in a blend through KMD analysis was demonstrated.

PCR Incorporation of Polyoxometalate Modified Deoxynucleotide Triphosphates and Their Application in Molecular Electrochemical Sensing of Yersinia pestis.

Redox-labeled nucleotides are of increasing interest for the fabrication of next generation molecular tools and should meet requirements of being thermally stable, sensitive, and compatible with polymerase-mediated incorporation while also being electrochemically discriminable. The synthesis and characterization of Keggin and Dawson polyoxometalate-deoxynucleotide (POM-dNTP) bioconjugates linked through 7-deaza-modified purines is described. The modified POM-dNTPs were used for polymerase-based amplification of a DNA sequence specific for Yersinia pestis and the amplified DNA detected using an electrochemical DNA sensor. This highlights the potential of polyoxometalates as thermally stable, sensitive and polymerase-compatible redox labels for exploitation in bioanalytical applications.

Improved Steroids Detection and Evidence for Their Regiospecific Decompositions Using Anion Attachment Mass Spectrometry.

Nonpolar anabolic steroids are doping agents that typically do not provide strong signals by electrospray ionization-mass spectrometry (ESI-MS) owing especially to the low polarity of the functional groups present. We have investigated the addition of anions, in ammonium salt form, to anabolic steroid samples as ionization enhancers and have confirmed that lower instrumental limits of detection (as low as 10 ng/mL for fluoxymesterone-M) are obtained by fluoride anion attachment mass spectrometry, as compared to ESI(+)/(-) or atmospheric pressure photoionization (APPI)(+). Moreover, collision-induced decomposition (CID) spectra of precursor fluoride adducts of the bifunctional steroid "reduced pregnenolone" (containing two hydroxyl groups) and its d4-analogue provide evidence of regiospecific decompositions after attachment of fluoride anion to a specific hydroxyl group of the steroid. This type of charting of specific CID reaction pathways can offer value to selected reaction monitoring experiments (SRM) as it may result in a gain in selectivity in detection as well as in improvements in quantification.

Combined use of direct analysis in real-time/Orbitrap mass spectrometry and micro-Raman spectroscopy for the comprehensive characterization of real explosive samples.

Direct Analysis in Real Time (DART™) high-resolution Orbitrap™ mass spectrometry (HRMS) in combination with Raman microscopy was used for the detailed molecular level characterization of explosives including not only the charge but also the complex matrix of binders, plasticizers, polymers, and other possible organic additives. A total of 15 defused military weapons including grenades, mines, rockets, submunitions, and mortars were examined. Swabs and wipes were used to collect trace (residual) amounts of explosives and their organic constituents from the defused military weapons and micrometer-size explosive particles were transferred using a vacuum suction-impact collection device (vacuum impactor) from wipe and swap samples to an impaction plate made of carbon. The particles deposited on the carbon plate were then characterized using micro-Raman spectroscopy followed by DART-HRMS providing fingerprint signatures of orthogonal nature. The optical microscope of the micro-Raman spectrometer was first used to localize and characterize the explosive charge on the impaction plate which was then targeted for identification by DART-HRMS analysis in both the negative and positive modes. Raman spectra of the explosives TNT, RDX and PETN were acquired from micrometer size particles and characterized by the presence of their characteristic Raman bands obtained directly at the surface of the impaction plate nondestructively without further sample preparation. Negative mode DART-HRMS confirmed the types of charges contained in the weapons (mainly TNT, RDX, HMX, and PETN; either as individual components or as mixtures). These energetic compounds were mainly detected as deprotonated species [M-H](-), or as adduct [M + (35)Cl](-), [M + (37)Cl](-), or [M + NO3](-) anions. Chloride adducts were promoted in the heated DART reagent gas by adding chloroform vapors to the helium stream using an "in-house" delivery method. When the polarity was switched to positive mode, DART-HRMS revealed a very complex distribution of polymeric binders (mainly polyethylene glycols and polypropylene glycols), plasticizers (e.g., dioctyl sebacate, tributyl phosphate), as well as wax-like compounds whose structural features could not be precisely assigned. In positive mode, compounds were identified either as protonated molecules or ammonium adduct species. These results clearly demonstrate the complementarity of micro-Raman microscopy combined with DART-MS. The former technique provides structural information on the type of explosives present at the surface of the sample, whereas the latter provides not only a confirmation of the nature of the explosive charge but also useful additional information regarding the nature of the complex organic matrix of binders, plasticizers, polymers, oils, and potentially other organic additives and contaminants present in the sample. Combining these two techniques provides a powerful tool for the screening, comprehensive characterization, and differentiation of particulate explosive samples for forensic sciences and homeland security applications. Graphical Abstract Comprehensive characterization of explosive particles collected from swipe samples by micro-Raman and DART™-HRMS.

Understanding paper degradation: identification of products of cellulosic paper decomposition at the wet-dry "tideline" interface using GC-MS.

Cellulose paper degradation products forming in the "tideline" area at the wet-dry interface of pure cellulose paper were analyzed using gas chromatography-electron ionization-mass spectrometry (GC-EI-MS) and high-resolution electrospray ionization-mass spectrometry (ESI-MS, LTQ Orbitrap) techniques. Different extraction protocols were employed in order to solubilize the products of oxidative cellulose decomposition, i.e., a direct solvent extraction or a more laborious chromophore release and identification (CRI) technique aiming to reveal products responsible for paper discoloration in the tideline area. Several groups of low molecular weight compounds were identified, suggesting a complex pathway of cellulose decomposition in the tidelines formed at the cellulose-water-oxygen interface. Our findings, namely the appearance of a wide range of linear saturated carboxylic acids (from formic to nonanoic), support the oxidative autocatalytic mechanism of decomposition. In addition, the identification of several furanic compounds (which can be, in part, responsible for paper discoloration) plus anhydro carbohydrate derivatives sheds more light on the pathways of cellulose decomposition. Most notably, the mechanisms of tideline formation in the presence of molecular oxygen appear surprisingly similar to pathways of pyrolytic cellulose degradation. More complex chromophore compounds were not detected in this study, thereby revealing a difference between this short-term tideline experiment and longer-term cellulose aging.

Jean-Antoine Nollet: The father of experimental electrospray.

The development of electrospray ionization mass spectrometry (ESI-MS) was a 20th century occurrence that underwent rapid acceleration especially in the 1990's. However, long prior to its coupling with mass spectrometry, the electrification of liquids had been studied in a variety of contexts. Although initial reports describing cone formation upon electrification of water drops came out of England, the first true experiments investigating the electrospray phenomenon were performed in the middle of the 18th century by Abbé Jean-Antoine Nollet. The current report, associated with the French Regional Issue of Mass Spectrometry Reviews, examines the contributions of Abbé Nollet to the earliest understanding of the electrospray phenomenon. A description of his accomplishments is placed in the context of the societal and scientific developments of the "Age of Enlightenment" out of which Jean-Antoine Nollet arose.

Biofunctionalization of Polyoxometalates with DNA Primers, Their Use in the Polymerase Chain Reaction (PCR) and Electrochemical Detection of PCR Products.

The bioconjugation of polyoxometalates (POMs), which are inorganic metal oxido clusters, to DNA strands to obtain functional labeled DNA primers and their potential use in electrochemical detection have been investigated. Activated monooxoacylated polyoxotungstates [SiW11 O39 {Sn(CH2 )2 CO}](8-) and [P2 W17 O61 {Sn(CH2 )2 CO}](6-) have been used to link to a 5'-NH2 terminated 21-mer DNA forward primer through amide coupling. The functionalized primer was characterized by using a battery of techniques, including electrophoresis, mass spectrometry, as well as IR and Raman spectroscopy. The functionality of the POM-labeled primers was demonstrated through hybridization with a surface-immobilized probe. Finally, the labeled primers were successfully used in the polymerase chain reaction (PCR) and the PCR products were characterized by using electrophoresis.

New insights into dissociation of deprotonated 2,4-dinitrotoluene by combined high-resolution mass spectrometry and density functional theory calculations.

RATIONALE: 2,4-Dinitrotoluene (2,4-DNT) is a nitroaromatic explosive which is commonly found in environmental samples close to training points, firing places, and manufacturers. Mass spectrometry analysis of this compound shows one main product ion that distinguishes it from the other isomers of DNT. We present here a detailed mechanistic study on the formation of this ion. METHODS: 2,4-DNT was analyzed using negative electrospray ionization high-resolution mass spectrometry (ESI-HRMS) using a linear ion trap quadrupole LTQ-Orbitrap XL mass spectrometer. Collision-induced dissociation (CID) experiments were performed on the [M-H](-) ion obtained. Density functional theory (DFT) calculations were used to support experimental observations. RESULTS: Fragmentation of deprotonated 2,4-DNT [M-H](-) (m/z 181) yields a main product ion at m/z 116. The mechanism of formation of this diagnostic product ion is not obvious and it has never been rationalized. Calculations were performed to probe different mechanistic variants, which are discussed in this work. CONCLUSIONS: Analysis of possible pathways to form the m/z 116 ion from the m/z 181 precursor shows that its formation is likely to proceed first via NO(•) loss, followed by eliminations of H2 O and then HO(•) .

A study of procyanidin binding to Histatin 5 using Electrospray Ionization Tandem Mass Spectrometry (ESI-MS/MS) and molecular simulations.

Tannins act as antioxidants, anticarcinogens, cardio-protectants, anti-inflammatory and anti-microbial agents and bind to salivary peptides by hydrophilic and hydrophobic mechanisms. Electrospray Ionization Mass Spectrometry (ESI-MS) has been used to assess both hydrophilic and hydrophobic components of noncovalent binding in protein complexes. In the present study, direct infusion Electrospray-Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (ES-FTICR MS) is used to assess relative binding affinities of procyanidin tannin stereoisomers for salivary peptides arising from aqueous solutions. The condensed tannins procyanidin B1, B2, B3, and B4 demonstrate significantly different binding affinities for the salivary peptide Histatin 5. Rigid docking combined with molecular dynamics optimization is used to investigate procyanidin-Histatin 5 binding mechanisms and as a basis to rationalize trends found in the corresponding ES-FTICR MS experiments. The relative binding affinities of the four procyanidin rotamers are different in the gas and liquid phases. The simulation results indicate that many of the same contact points are made in both phases, but there is a increase in strong electrostatic interactions and an decrease in π-π contacts upon transfer from the liquid to the gas phase. The simulations reveal that the tannin interactions can make close contacts with a variety of amino acid residues on the peptide.

Structural and biochemical characterization of the bilin lyase CpcS from Thermosynechococcus elongatus.

Cyanobacterial phycobiliproteins have evolved to capture light energy over most of the visible spectrum due to their bilin chromophores, which are linear tetrapyrroles that have been covalently attached by enzymes called bilin lyases. We report here the crystal structure of a bilin lyase of the CpcS family from Thermosynechococcus elongatus (TeCpcS-III). TeCpcS-III is a 10-stranded ß barrel with two alpha helices and belongs to the lipocalin structural family. TeCpcS-III catalyzes both cognate as well as noncognate bilin attachment to a variety of phycobiliprotein subunits. TeCpcS-III ligates phycocyanobilin, phycoerythrobilin, and phytochromobilin to the alpha and beta subunits of allophycocyanin and to the beta subunit of phycocyanin at the Cys82-equivalent position in all cases. The active form of TeCpcS-III is a dimer, which is consistent with the structure observed in the crystal. With the use of the UnaG protein and its association with bilirubin as a guide, a model for the association between the native substrate, phycocyanobilin, and TeCpcS was produced.

Screening and identification of glyceollins and their metabolites by electrospray ionization tandem mass spectrometry with precursor ion scanning.

A method has been developed for screening glyceollins and their metabolites based on precursor ion scanning. Under higher-energy collision conditions with the employment of a triple quadrupole mass spectrometer in the negative ion mode, deprotonated glyceollin precursors yield a diagnostic radical product ion at m/z 148. We propose this resonance-stabilized radical anion, formed in violation of the even-electron rule, to be diagnostic of glyceollins and glyceollin metabolites. Liquid chromatography-electrospray ionization tandem mass spectrometry (LC-ESI-MS/MS) established that scanning for precursors of m/z 148 can identify glyceollins and their metabolites from plasma samples originating from rats dosed with glyceollins. Precursor peaks of interest were found at m/z 337, 353, 355, 417, and 433. The peak at m/z 337 corresponds to deprotonated glyceollins, whereas the others represent metabolites of glyceollins. Accurate mass measurement confirmed m/z 417 to be a sulfated metabolite of glyceollins. The peak at m/z 433 is also sulfated, but it contains an additional oxygen, as confirmed by accurate mass measurement. The latter metabolite differs from the former likely by the replacement of a hydrogen with a hydroxyl moiety. The peaks at m/z 353 and 355 are proposed to correspond to hydroxylated metabolites of glyceollins, wherein the latter additionally undergoes a double bond reduction.

Characterization of the activities of the CpeY, CpeZ, and CpeS bilin lyases in phycoerythrin biosynthesis in Fremyella diplosiphon strain UTEX 481.

When grown in green light, Fremyella diplosiphon strain UTEX 481 produces the red-colored protein phycoerythrin (PE) to maximize photosynthetic light harvesting. PE is composed of two subunits, CpeA and CpeB, which carry two and three phycoerythrobilin (PEB) chromophores, respectively, that are attached to specific Cys residues via thioether linkages. Specific bilin lyases are hypothesized to catalyze each PEB ligation. Using a heterologous, coexpression system in Escherichia coli, the PEB ligation activities of putative lyase subunits CpeY, CpeZ, and CpeS were tested on the CpeA and CpeB subunits from F. diplosiphon. Purified His(6)-tagged CpeA, obtained by coexpressing cpeA, cpeYZ, and the genes for PEB synthesis, had absorbance and fluorescence emission maxima at 566 and 574 nm, respectively. CpeY alone, but not CpeZ, could ligate PEB to CpeA, but the yield of CpeA-PEB was lower than achieved with CpeY and CpeZ together. Studies with site-specific variants of CpeA(C82S and C139S), together with mass spectrometric analysis of trypsin-digested CpeA-PEB, revealed that CpeY/CpeZ attached PEB at Cys(82) of CpeA. The CpeS bilin lyase ligated PEB at both Cys(82) and Cys(139) of CpeA but very inefficiently; the yield of PEB ligated at Cys(82) was much lower than observed with CpeY or CpeY/CpeZ. However, CpeS efficiently attached PEB to Cys(80) of CpeB but neither CpeY, CpeZ, nor CpeY/CpeZ could ligate PEB to CpeB.

Determination of peptide topology through time-resolved double-resonance under electron capture dissociation conditions.

Characterizing the conformation of biomolecules by mass spectrometry still represents a challenge. With their knotted structure involving a N-terminal macrolactam ring where the C-terminal tail of the peptide is threaded and sterically trapped, lasso peptides constitute an attractive model for developing methods for characterizing gas-phase conformation, through comparison with their unknotted topoisomers. Here, the kinetics of electron capture dissociation (ECD) of a lasso peptide, capistruin, was investigated by electrospray ionization-Fourier transform ion cyclotron resonance mass spectrometry and compared to that of its branched-cyclic topoisomer, lactam-capistruin. Both peptides produced rather similar ECD spectra but showed different extent of H(•) transfer from c(i)' to z(j)(•) ions. Time-resolved double-resonance experiments under ECD conditions were performed to measure the formation rate constants of typical product ions. Such experiments showed that certain product ions, in particular those related to H(•) transfer, proceeded through long-lived complexes for capistruin, while fast dissociation processes predominated for lactam-capistruin. The formation rate constants of specific ECD product ions enabled a clear differentiation of the lasso and branched-cyclic topoisomers. These results indicate that the formation kinetics of ECD product ions constitute a new way to explore the conformation of biomolecules and distinguish between topoisomers and, more generally, conformers.

Benchmarking higher energy collision dissociation (HCD) by investigation of binding energies of gas-phase host-guest complexes of hemicryptophane cages.

Synthesis of host molecules that feature well-defined characteristics for molecular recognition of guest molecules is often a major aim of synthetic host-guest (H-G) chemistry. A key consideration in evaluating the selectivity of hosts and the affinities of guests is the measurement of binding energies of obtained H-G complexes. In contrast to nuclear magnetic resonance (NMR) or fluorescence measurements that are capable of measuring binding strengths in solution, mass spectrometry offers the opportunity to measure gas-phase binding energies. Presented in this article is a higher energy collision dissociation (HCD) approach for determining critical energies of dissociation of H-G complexes. Experiments were performed on electrospray ionization (ESI)-generated H-G pairs in an LTQ-XL/Orbitrap hybrid instrument. The presented HCD approach requires preliminary calibration of the internal energy distribution of generated ions that was achieved by the use of activation parameters that were known from previous low-energy collision-induced dissociation (low-energy CID) experiments. Internal energy deposition was modeled based on a truncated Maxwell-Boltzmann distribution and characteristic temperature (Tchar ). Using this method, critical energies of dissociation were determined for 10 H-G biologically relevant complexes of the heteroditopic hemicryptophane cage host (Host). Obtained results are compared with those found previously by low-energy CID. The use of this HCD technique is relatively straightforward, although its implementation does require knowledge (or a presumption) about the Arrhenius pre-exponential factor of the complexes to obtain their critical energies of dissociation.

Investigation of space charge effects and ion trapping capacity on direct introduction ultra-high-resolution mass spectrometry workflows for metabolomics.

Ultra-high-resolution mass spectrometry, in the absence of chromatography, is finding its place for direct analyses of highly complex mixtures, such as those encountered during untargeted metabolomics screening. Advances, however, have been tempered by difficulties such as uneven signal suppression experienced during electrospray ionization. Moreover, ultra-high-resolution mass spectrometers that use Orbitrap and ICR analyzers both suffer from limited ion trapping capacities, owing principally to space-charge effects. This study has evaluated and contrasted the above two types of Fourier transform mass spectrometers for their abilities to detect and identify by accurate mass measurement, small molecule metabolites present in complex mixtures. For these direct introduction studies, the Orbitrap Fusion showed a major advantage in terms of speed of analysis, enabling detection of 218 of 440 molecules (<2 ppm error, 500 000 resolution at m/z 200) present in a complex mixture in 5 min. This approach is the most viable for high-throughput workflows, such as those used in investigations involving very large cohorts of metabolomics samples. From the same mixture, 183 unique molecules were observed by FT-ICR in the broadband mode, but this number was raised to 235 when "selected ion monitoring-stitching" (SIM-stitching) was employed (<0.1 ppm error, 7 T magnet with dynamic harmonization cell, 1.8 million resolution at m/z 200, both cases). SIM-stitching FT-ICR thus offered the most complete detection, which may be of paramount importance in situations where it is essential to obtain the most complete metabolic profile possible. This added completeness, however, came at the cost of a more lengthy analysis time (120 min including manual treatment). Compared to the data presented here, future automation of processing, plus the use of absorption mode detection, segmented ion detection (stepwise detection of smaller width m/z sections), and higher magnetic field strengths, can substantially reduce FT-ICR acquisition times.