Degradation of Amaranth azo dye in water by heterogeneous photo-Fenton process using FeWO4 catalyst prepared by microwave irradiation.

FeWO4 particles were synthesized by a simple, rapid and facile microwave technique and their catalytic properties in heterogeneous photo-Fenton reaction were evaluated. This material was employed in the degradation of Amaranth azo dye. Individual and interactive effects of operational parameters such as pH, dye concentration and H2O2 dosage on the decolorization efficiency of Amaranth dye were evaluated by 2(3) central composite design. According to characterization techniques, a porous material and a well-crystallized phase of FeWO4 oxide were obtained. Regarding the photo-Fenton reaction assays, up to 97% color and 58% organic carbon removal were achieved in the best experimental conditions. In addition, the photo-Fenton process maintained treatment efficiency over five catalyst reuse cycles to indicate the durability of the FeWO4 catalyst. In summary, the results reveal that the synthesized FeWO4 material is a promising catalyst for wastewater treatment by heterogeneous photo-Fenton process.

Removal of hazardous pharmaceutical dyes by adsorption onto papaya seeds.

Papaya (Carica papaya L.) seeds were used as adsorbent to remove toxic pharmaceutical dyes (tartrazine and amaranth) from aqueous solutions, in order to extend application range. The effects of pH, initial dye concentration, contact time and temperature were investigated. The kinetic data were evaluated by the pseudo first-order, pseudo second-order and Elovich models. The equilibrium was evaluated by the Langmuir, Freundlich and Temkin isotherm models. It was found that adsorption favored a pH of 2.5, temperature of 298 K and equilibrium was attained at 180-200 min. The adsorption kinetics followed the pseudo second-order model, and the equilibrium was well represented by the Langmuir model. The maximum adsorption capacities were 51.0 and 37.4 mg g(-1) for tartrazine and amaranth, respectively. These results revealed that papaya seeds can be used as an alternative adsorbent to remove pharmaceutical dyes from aqueous solutions.

Adsorption of leather dye onto activated carbon prepared from bottle gourd: equilibrium, kinetic and mechanism studies.

Activated carbon prepared from bottle gourd has been used as adsorbent for removal of leather dye (Direct Black 38) from aqueous solution. The activated carbon obtained showed a mesoporous texture, with surface area of 556.16 m(2) g(-1), and a surface free of organic functional groups. The initial dye concentration, contact time and pH significantly influenced the adsorption capacity. In the acid region (pH 2.5) the adsorption of dye was more favorable. The adsorption equilibrium was attained after 60 min. Equilibrium data were analyzed by the Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. The equilibrium data were best described by the Langmuir isotherm, with maximum adsorption capacity of 94.9 mg g(-1). Adsorption kinetic data were fitted using the pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The adsorption kinetic was best described by the second-order kinetic equation. The adsorption process was controlled by both external mass transfer and intraparticle diffusion. Activated carbon prepared from bottle gourd was shown to be a promising material for adsorption of Direct Black 38 from aqueous solution.

Activated carbon prepared from yerba mate used as a novel adsorbent for removal of tannery dye from aqueous solution.

Activated carbon prepared from yerba mate (Ilex paraguariensis) was used as adsorbent for the removal of tannery dye from aqueous solution. The activated carbon was characterized, and it showed a mesoporous texture, with surface area of 537.4 m2 g(-1). The initial dye concentration, contact time and pH influenced the adsorption capacity. The equilibrium data were in good agreement with both Langmuir and Freundlich isotherms. The adsorption kinetics of the tannery dye on activated carbon prepared from yerba mate followed a pseudo-second-order model. The adsorption process was found to be controlled by both external mass-transfer and intraparticle diffusion, but the external diffusion was the dominating process. This work highlights the potential application of activated carbon produced from yerba mate in the field of adsorption.

Valorization of a poultry industry floated sludge as a raw material to produce char and activated carbon for pharmaceutical compounds adsorption.

This study was intended to valorize a floated sludge of a poultry slaughterhouse using it as a precursor to producing char and activated carbon, which were tested as adsorbents in removing ketoprofen and diclofenac sodium from the water. The addition of zinc chloride or calcium hydroxide was determinant for forming a porous carbonaceous structure with a high surface area in AC-FSP (656.54 m2 g-1), differently from that exhibited by the CHAR-FSP (8.11 m2 g-1). Kinetic and equilibrium studies indicated that the pseudo-second-order and the Sips models were suitable. The AC- FSP maximum adsorption capacity for ketoprofen and diclofenac sodium was 124.98 mg g-1 and 138.32 mg g-1, respectively. The adsorption was a spontaneous and endothermic process. It was concluded that AC-FSP is a more efficient and promising adsorbent than CHAR-FSP for the adsorption of drugs in contaminated wastewater. In addition, AC-FSP can be reused, maintaining good adsorption levels for about 5 cycles. Therefore, this study is aligned with the 2030 Agenda for global sustainability since converting waste (valueless) into an adsorbent is also directly linked to the circular economy and neutral carbon.

Degradation of Direct Black 38 dye under visible light and sunlight irradiation by N-doped anatase TIO2 as photocatalyst.

The N-doped TiO(2) photocatalyst was prepared by calcination of a hydrolysis product composed of titanium (IV) isopropoxide with ammonia as the precipitator. X-ray diffraction, surface area, XPS and UV-vis spectra analyses showed a nanosized anatase structure and the appearance of a new absorption band in the visible region caused by nitrogen doping. The degradation of Direct Black 38 dye on the nitrogen-doped TiO(2) photocatalyst was investigated under visible light and sunlight irradiation. The N-doped anatase TiO(2) demonstrated excellent photocatalytic activity under visible light. Under sunlight irradiation, the N-doped sample showed slightly higher activity than that of the non-doped sample.

Preparation of carbonaceous materials from pyrolysis of chicken bones and its application for fuchsine adsorption.

Activated carbon and biochar were obtained from chicken bone (CB), characterized, and applied to remove basic fuchsine from aqueous media. The adsorbent dosage and pH effects were studied, as well as kinetic, equilibrium, and thermodynamic curves were constructed. The values of BET surface area and total pore volume were 108.94 m2 g-1 and 0.219 cm3 g-1 for the activated carbon and, 18.72 m2 g-1 and 0.075 cm3 g-1 for the biochar. The dye removal percentages were 93.63 and 55.38% when 2.5 g L-1 of activated carbon and biochar were used, respectively. The adsorption was favored using 0.5 g L-1 of adsorbent and pH of 7.0. Adsorption kinetics was well represented by the pseudo-second-order model. Langmuir model was the best to represent the equilibrium. Maximum adsorption capacity was 260.8 mg g-1, obtained using activated carbon. The process was endothermic, favorable, and spontaneous. Results showed that alternative carbonaceous materials can be obtained from chicken bones and used as adsorbents to treat colored effluents containing fuchsine.

Iron-based adsorbent prepared from Litchi peel biomass via pyrolysis process for the removal of pharmaceutical pollutant from synthetic aqueous solution.

A porous iron-based adsorbent obtained from litchi peel via pyrolysis process was prepared in this work, in order to evaluate its adsorptive potential for the removal of a pharmaceutical dye (amaranth) from aqueous solution. The material was characterized by X-ray diffraction, nitrogen adsorption-desorption isotherms, and scanning electron microscopy. Several isotherm and kinetic models were tested aiming to represent the amaranth dye adsorption. The prepared sample presented magnetic property, and a mesoporous texture constituted of graphite and three iron-based phases. The adsorption kinetics of amaranth on the adsorbent followed the pseudo-second-order model, whereas the equilibrium data were in good agreement with the BET isotherm, being represented by a sigmoid-shaped adsorption isotherm. The maximum adsorption capacity for the amaranth dye was found to be 44.87 mg g-1, demonstrating that the material prepared in this work showed to be a promising adsorbent for the removal of amaranth from aqueous solution.