Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking.

In this work, the design of a wideband low-noise amplifier (LNA) using a resistive feedback network is proposed for potential multi-band sensing, communication, and radar applications. For achieving wide operational bandwidth and flat in-band characteristics simultaneously, the proposed LNA employs a variety of circuit design techniques, including a voltage-current (shunt-shunt) negative feedback configuration, inductive emitter degeneration, a main branch with an added cascode stage, and the shunt-peaking technique. The use of a feedback network and emitter degeneration provides broadened transfer characteristics for multi-octave coverage and a real impedance for input matching, respectively. In addition, the cascode stage pushes the band-limiting low-frequency pole, due to the Miller capacitance, to a higher frequency. Lastly, the shunt-peaking approach is optimized for the compensation of a gain reduction at higher frequency bands. The wideband LNA proposed in this study is fabricated using a commercial 0.13 µm silicon-germanium (SiGe) BiCMOS process, employing SiGe heterojunction bipolar transistors (HBTs) as the circuit's core active elements in the main branch. The measurement results show an operational bandwidth of 2.0-29.2 GHz, a noise figure of 4.16 dB (below 26.5 GHz, which was the measurement limit), and a total power consumption of 23.1 mW under a supply voltage of 3.3 V. Regarding the nonlinearity associated with large-signal behavior, the proposed LNA exhibits an input 1-dB compression (IP1dB) point of -5.42 dBm at 12 GHz. These performance numbers confirm the strong viability of the proposed approach in comparison with other state-of-the-art designs.

Mitigation of Single-Event Effects in SiGe-HBT Current-Mode Logic Circuits.

It has been known that negative feedback loops (internal and external) in a SiGe heterojunction bipolar transistors (HBT) DC current mirrors improve single-event transient (SET) response; both the peak transient current and the settling time significantly decrease. In the present work, we demonstrate how radiation hardening by design (RHBD) techniques utilized in DC bias blocks only (current mirrors) can also improve the SET response in AC signal paths of switching circuits (e.g., current-mode logic, CML) without any additional hardening in those AC signal paths. Four CML circuits both with and without RHBD current mirrors were fabricated in 130 nm SiGe HBT technology. Two existing RHBD techniques were employed separately in the current mirrors of the CML circuits: (1) applying internal negative feedback and (2) adding a large capacitor in a sensitive node. In addition, these methods are also combined to analyze the overall SET performance. The single-event transients of the fabricated circuits were captured under the two-photon-absorption laser-induced single-event environment. The measurement data clearly show significant improvements in SET response in the AC signal paths of the CML circuits by using the two radiation hardening techniques applied only in DC current mirrors. The peak output transient current is notably reduced, and the settling time upon a laser strike is shortened significantly.

Using Bessel beams and two-photon absorption to predict radiation effects in microelectronics.

Pulsed-laser testing is an attractive tool for studying space-based radiation effects in microelectronics because it provides a high degree of spatial resolution and is more cost-effective than conventional accelerator-based testing. However, quantitatively predicting the effects of radiation is challenging for this optical method. A new approach to pulsed-laser testing is presented, which addresses these challenges by using a Bessel beam and carrier generation via two-photon absorption. By producing a carrier distribution in the device under test that is similar to that of a heavy ion, this optical approach aims to quantitatively predict the response of the device under heavy ion tests that represent space radiation. Furthermore, the carrier distribution can be accurately described using a single analytic expression thereby enabling the laser to be tuned to emulate a specific heavy ion. Herein, we describe the modifications made to an existing pulsed-laser setup to generate this carrier distribution, characterize this distribution using a novel method that provides sub-micron spatial resolution, and provide the equations that describe the distribution. Finally, we use this method to study a silicon photodiode and find that the transient response of the device shows strong agreement with the response generated using heavy ions.

Record maximum oscillation frequency in C-face epitaxial graphene transistors.

The maximum oscillation frequency (fmax) quantifies the practical upper bound for useful circuit operation. We report here an fmax of 70 GHz in transistors using epitaxial graphene grown on the C-face of SiC. This is a significant improvement over Si-face epitaxial graphene used in the prior high-frequency transistor studies, exemplifying the superior electronics potential of C-face epitaxial graphene. Careful transistor design using a high κ dielectric T-gate and self-aligned contacts further contributed to the record-breaking fmax.