Airflow restriction mask induces greater central fatigue after a non-exhaustive high-intensity interval exercise.

The airflow restriction mask (ARM) is a practical and inexpensive device for respiratory muscle training. Wearing an ARM has recently been combined with high-intensity interval exercise (HIIE), but its effect on neuromuscular fatigue is unknown. The present study investigated the effects of ARM wearing on neuromuscular fatigue after an HIIE session. Fourteen healthy men performed two HIIE sessions (4 × 4 min at 90% HRmax , 3 min recovery at 70% HRmax ) with or without an ARM. Neuromuscular fatigue was quantified via pre- to post-HIIE changes in maximal voluntary contraction (MVC), voluntary activation (VA, central fatigue), and potentialized evoked twitch force at 100, 10, and 1 Hz (peripheral fatigue). Blood pH and lactate were measured before and after the HIIE session, while HR, SpO2 , dyspnea, physical sensation of effort (P-RPE), and Task Effort and Awareness (TEA) were recorded every bout. The exercise-induced decrease in MVC was higher (p < 0.05) in the ARM (-28 ± 12%) than in the Control condition (-20 ± 11%). The VA decreased (p < 0.05) in the ARM (-11 ± 11%) but not in the control condition (-4 ± 5%, p > 0.05). Pre- to post-HIIE declines in evoked twitch at 100, 10, and 1 Hz were similar (p > 0.05) between ARM and control conditions (ARM: -18 ± 10, -43 ± 11 and -38 ± 12%; Control: -18 ± 14, -43 ± 12 and -37 ± 17%). When compared with the control, the HIIE bout wearing ARM was marked by higher heart rate, plasma lactate concentration, dyspnea, P-RPE and TEA, as well as lower SpO2 and blood pH. In conclusion, ARM increases perceptual and physiological stress during a HIIE, which may lead to a greater post-exercise central fatigue.

Poly(L-co-D,L lactic acid-co-Trimethylene Carbonate) 3D printed scaffold cultivated with mesenchymal stem cells directed to bone reconstruction: In vitro and in vivo studies.

A recent and quite promising technique for bone tissue engineering is the 3D printing, peculiarly regarding the production of high-quality scaffolds. The 3D printed scaffold strictly provides suitable characteristics for living cells, in order to induce treatment, reconstruction and substitution of injured tissue. The purpose of this work was to evaluate the behavior of the 3D scaffold based on Poly(L-co-D,L lactic acid-co-Trimethylene Carbonate) (PLDLA-TMC), which was designed in Solidworks™ software, projected in 3D Slicer™, 3D printed in filament extrusion, cultured with mesenchymal stem cells (MSCs) and tested in vitro and in vivo models. For in vitro study, the MSCs were seeded in a PLDLA-TMC 3D scaffold with 600 µm pore size and submitted to proliferation and osteogenic differentiation. The in vivo assays implanted the PLDLA-TMC scaffolds with or without MSCs in the calvaria of Wistar rats submitted to 8 mm cranial bone defect, in periods of 8-12 weeks. The results showed that PLDLA-TMC 3D scaffolds favored adherence and cell growth, and suggests an osteoinductive activity, which means that the material itself augmented cellular differentiation. The implanted PLDLA-TMC containing MSCs, showed better results after 12 weeks prior grafting, due the absence of inflammatory processes, enlarged regeneration of bone tissue and facilitated angiogenesis. Notwithstanding, the 3D PLDLA-TMC itself implanted enriched tissue repair; the addition of cells known to upregulate tissue healing reinforce the perspectives for the PLDLA-TMC applications in the field of bone tissue engineering in clinical trials.