Anhydrous Superprotonic Conductivity in the Zirconium Acid Triphosphate ZrH5 (PO4 )3.

The development of solid-state proton conductors with high proton conductivity at low temperatures is crucial for the implementation of hydrogen-based technologies for portable and automotive applications. Here, we report on the discovery of a new crystalline metal acid triphosphate, ZrH5 (PO4 )3 (ZP3), which exhibits record-high proton conductivity of 0.5-3.1×10-2  S cm-1 in the range 25-110 °C in anhydrous conditions. This is the highest anhydrous proton conductivity ever reported in a crystalline solid proton conductor in the range 25-110 °C. Superprotonic conductivity in ZP3 is enabled by extended defective frustrated hydrogen bond chains, where the protons are dynamically disordered over two oxygen centers. The high proton conductivity and stability in anhydrous conditions make ZP3 an excellent candidate for innovative applications in fuel cells without the need for complex water management systems, and in other energy technologies requiring fast proton transfer.

Synthesis, Crystal Structure, and Antibacterial Properties of Silver-Functionalized Low-Dimensional Layered Zirconium Phosphonates.

New insoluble layered zirconium phosphate carboxyaminophosphonates (ZPs), with the general formula Zr2(PO4)H5[(O3PCH2)2N(CH2)nCOO]2·mH2O (n = 3, 4, and 5), have been prepared and characterized. The crystal structure for n = 3 and 4 samples was determined ab initio from X-ray powder diffraction data. The structure for n = 3 was monoclinic in space group C2/c with the following unit cell parameters: a = 34.346(1) Å, b = 8.4930(2) Å, c = 9.0401(2) Å, and ß = 97.15(1)°. The structure for n = 4 was triclinic in space group P1̅ with the following unit cell parameters: a = 17.9803(9) Å, b = 8.6066(4) Å, c = 9.0478(3) Å, α = 90.466(3)°, ß = 94.910(4)°, and γ = 99.552(4)°. The two structures had the same connectivity as Zr phosphate glycine diphosphonate (n = 1), as previously reported. By intercalation of short amines, these layered compounds were exfoliated in single lamella or packets of a few lamellae, which formed colloidal dispersions in water. After a thorough characterization, the dispersed lamellae were functionalized with Ag nanoparticles, which were grown in situ on the surface of exfoliated lamellae. Finally, their antimicrobial activity was tested on several Gram-positive and Gram-negative bacteria. All of these systems were found to be active against the four pathogens most frequently isolated from orthopedic prosthetic infections and often causative of nosocomial infections. Interestingly, they were found to express powerful inhibitory activity even against bacterial strains exhibiting a relevant profile of antibiotic resistance such as Staphylococcus aureus ATCC 700699.

Eco-Sustainable Silk Fibroin/Pomegranate Peel Extract Film as an Innovative Green Material for Skin Repair.

Skin disorders are widespread around the world, affecting people of all ages, and oxidative stress represents one of the main causes of alteration in the normal physiological parameters of skin cells. In this work, we combined a natural protein, fibroin, with antioxidant compounds extracted in water from pomegranate waste. We demonstrate the effective and facile fabrication of bioactive and eco-sustainable films of potential interest for skin repair. The blended films are visually transparent (around 90%); flexible; stable in physiological conditions and in the presence of trypsin for 12 days; able to release the bioactive compounds in a controlled manner; based on Fickian diffusion; and biocompatible towards the main skin cells, keratinocytes and fibroblasts. Furthermore, reactive oxygen species (ROS) production tests demonstrated the high capacity of our films to reduce the oxidative stress induced in cells, which is responsible for various skin diseases.

Tumor Targeting by Peptide-Decorated Gold Nanoparticles.

Cancer remains one of the most important challenges in biomedical sciences. Chemotherapeutic agents are very potent molecules that exhibit a significant level of toxicity in numerous tissues of the body, particularly in those characterized by high proliferative activity, such as the bone marrow. The scenario is even more complex in the case of the central nervous system, and in particular brain tumors, where the blood brain barrier limits the efficacy of drug therapies. Integrins, transmembrane proteins widely expressed in different types of cancer (glioblastoma, melanoma, and breast cancer), regulate the angiogenic process and play a pivotal role in tumor growth and invasion. Here, we report a nanotechnology strategy based on the use of AuNPs decorated with an arginine-glycine-aspartic acid-like peptide for the diagnosis and treatment of cancer. Two hours after administration in mice, the accumulation of the peptide-decorated NPs in the subcutaneous tumor was ∼4-fold higher than that of uncoated particles and ∼1.4-fold higher than that of PEGylated particles. Also, in the case of the intracranial tumor model, interesting results were obtained. Indeed, 2 h after administration, the amount of peptide-decorated particles in the brain was 1.5-fold that of undecorated particles and 5-fold that of PEGylated particles. In conclusion, this preliminary study demonstrates the high potential of this carrier developed for diagnostic and therapeutic applications.

Small is beautiful: the unusual transformation of nanocrystalline layered α-zirconium phosphate into a new 3D structure.

Nanosized α-zirconium phosphate, α-ZrP, undergoes a phase transition at 120 °C, which is not observed with microcrystalline α-ZrP in the same conditions, and which leads to a new 3D phase. The new compound, with formula Zr(HPO4)2 (τ'-ZrP), consists of cubelike nanoparticles and has a tetragonal unit cell (space group P43212, a = 7.955 Å, c = 10.744 Å). The structure of τ'-ZrP is in close relationship with that of the already known τ-ZrP. Both structures are made of packed chains of eight-membered rings, composed of Zr atoms connected to bridging HPO4 groups. The main difference between the two structures concerns the different orientation of the uncoordinated P-OH groups, pointing into the channels. The in situ XRPD analysis on nanosized α-ZrP, performed at 120 °C as a function of time, provided information about the kinetics of the formation of τ'-ZrP, showing that the α-ZrP phase is directly transformed into τ'-ZrP. Moreover, τ'-ZrP is converted into α-ZrP at room temperature in the presence of water vapor. It was proved that the free phosphoric acid, which is originally present in small amounts in nanosized α-ZrP and τ'-ZrP, is necessary for the interconversion between the two phases. As a matter of fact, the removal of phosphoric acid, by washing α-ZrP and τ'-ZrP with anhydrous ethanol, inhibits the above conversion.

Water-mediated proton conduction in a robust triazolyl phosphonate metal-organic framework with hydrophilic nanochannels.

The development of water-mediated proton-conducting materials operating above 100 °C remains challenging because the extended structures of existing materials usually deteriorate at high temperatures. A new triazolyl phosphonate metal-organic framework (MOF) [La3L4(H2O)6]Cl⋅x H2O (1, L(2-) = 4-(4H-1,2,4-triazol-4-yl)phenyl phosphonate) with highly hydrophilic 1D channels was synthesized hydrothermally. Compound 1 is an example of a phosphonate MOF with large regular pores with 1.9 nm in diameter. It forms a water-stable, porous structure that can be reversibly hydrated and dehydrated. The proton-conducting properties of 1 were investigated by impedance spectroscopy. Magic-angle spinning (MAS) and pulse field gradient (PFG) NMR spectroscopies confirm the dynamic nature of the incorporated water molecules. The diffusivities, determined by PFG NMR and IR microscopy, were found to be close to that of liquid water. This porous framework accomplishes the challenges of water stability and proton conduction even at 110 °C. The conductivity in 1 is proposed to occur by the vehicle mechanism.

Innovative multifunctional silk fibroin and hydrotalcite nanocomposites: a synergic effect of the components.

Novel hybrid functional materials are formed by combining hydrotalcite-like compounds and silk fibroin (SF-HTlc) via an environmental friendly aqueous process. The nanocomposites can be prepared with different weight ratio of the constituting components and preserve the conformational properties of the silk protein and the lamellar structure of hydrotalcites. Optical microscopy, scanning electron microscopy, and atomic force microscopy analyses show a good dispersion degree of the inorganic nanoparticles into the organic silk matrix. A mutual benefit on the stability of both organic and inorganic components was observed in the nanocomposites. SF-HTlc displayed limited dissolution of hydrotalcite in acidic medium, enhanced mechanical properties, and higher protease resistance of silk protein. The transparency, flexibility, and acidic environment resistance of silk fibroin combined to the protective and reinforcing properties of hydrotalcites generate a hybrid material, which is very attractive for applications in recently reported silk based opto-electronic and photonics technologies.

A layered mixed zirconium phosphate/phosphonate with exposed carboxylic and phosphonic groups: X-ray powder structure and proton conductivity properties.

A novel mixed zirconium phosphate/phosphonate based on glyphosine, of formula Zr2(PO4)H5(L)2·H2O [L = (O3PCH2)2NCH2COO], was synthesized in mild conditions. The compound has a layered structure that was solved ab initio from laboratory PXRD data. It crystallizes in the monoclinic C2/c space group with the following cell parameters: a = 29.925(3), b = 8.4225(5), c = 9.0985(4) Å, and ß = 98.474(6)°. Phosphate groups are placed inside the sheets and connect the zirconium atoms in a tetradentate fashion, while uncoordinated carboxylate and P-OH phosphonate groups are exposed on the layer surface. Due to the presence of these acidic groups, the compound showed remarkable proton conductivity properties, which were studied in a wide range of temperature and relative humidity (RH). The conductivity is strongly dependent on RH and reaches 1 × 10(-3) S cm(-1) at 140 °C and 95% RH. At this RH, the activation energy of conduction is 0.15 eV in the temperature range 80-140 °C. The similarities of this structure with related structures already reported in the literature were also discussed.

Layered metal(IV) phosphonates with rigid pendant groups: new synthetic approaches to nanosized zirconium phosphate phenylphosphonates.

Single phase mixed zirconium phosphate phenylphosphonates, ZrP(PP)x, were prepared by two different synthetic approaches: reaction of gels of nanosized α-zirconium phosphate in propanol with solutions of phenylphosphonic acid (H2PP), leading to the topotactic exchange of monohydrogen phosphate groups with phenylphosphonate groups, and precipitation from propanol solutions of H2PP, phosphoric acid, and zirconyl propionate. In both cases, propanol intercalated compounds were obtained. The x values of the ZrP(PP)x materials prepared by topotactic anion exchange ranged from 0.37 to 0.56 for (H2PP/Zr) molar ratios in the range 0.52-4.16 and [H2PP] = 0.1 M, while a maximum x value of 0.73 was only reached at 60 °C, with (H2PP/Zr) = 4.16 and [H2PP] = 0.31 M. Direct precipitation of ZrP(PP)x provided samples with 0.13 ≤ x ≤ 1.54, for H2PP molar fractions in the range 0.05-0.5 and (P/Zr) molar ratio = 6. At 90% relative humidity, the (H2O/Zr) molar ratio for the precipitated ZrP(PP)x powder samples increased in the range 1.3-3.0 with increasing x and resulted in being higher than that of nanosized ZrP (0.8). The analysis of the X-ray diffraction patterns of the gel and powder samples, together with the hydration data of the powder samples, suggested a structural model in which the random distribution of the phosphate and phenylphosphonate groups creates cavities which can accommodate propanol molecules in the gel samples and water molecules in the hydrated powder samples.

Synthesis, crystal structure, and proton conductivity of one-dimensional, two-dimensional, and three-dimensional zirconium phosphonates based on glyphosate and glyphosine.

The reaction of two small phosphono-amino acids based on glycine (glyphosine and glyphosate) with zirconium under mild conditions led to the attainment of three related zirconium derivatives with 1D, 2D, and 3D structures of formulas ZrF[H3(O3PCH2NHCH2COO)2] (1), Zr3H8[(O3PCH2)2NCH2COO]4·2H2O (2), and Zr[(O3PCH2)(HO3PCH2)NHCH2COOH]2·2H2O (3), respectively, whose structures were solved by X-ray powder and single-crystal diffraction data. The glyphosate derivative has 1D ribbon-type structure whereas the dimensionality of the glyphosine-derived materials (2D and 3D) can be tuned by changing the synthesis conditions. The low-dimensional compounds (1 and 2) can be directly produced in the form of nanoparticles with different size and morphology whereas the 3D compound (3) has a higher crystallinity and can be obtained as single crystals with a prismatic shape. The different structural dimensionality reflects the shape and size of the crystals and also differently affects the proton conductivity properties, measured over a wide range of temperature at 95% relative humidity. Their high thermal and chemical stability together with the small size may promote their use as fillers for polymeric electrolyte membranes for fuel cells applications.

Looking for new hybrid polymer fillers: synthesis of nanosized α-type Zr(IV) organophosphonates through an unconventional topotactic anion exchange reaction.

Gels of α-type zirconium(IV) phosphate alkylphosphonates, ZP(Cn)x, were prepared by reacting, at room temperature, propanol intercalated nanosized α-zirconium phosphate (α-ZrP) with propanol solutions of alkylphosphonic acids (H2Cn, n = number of carbon atoms in the alkyl chain = 4, 5, 6), with (H2Cn/Zr) molar ratios in the range 0.4-4.0. (31)P MAS NMR showed the presence of resonances due to the phosphate and phosphonate groups bonded to the Zr atoms mainly by three oxygen atoms, as in the α-type layer. The composition of the ZP(Cn)x materials, obtained by thermogravimetric analysis, ranges from x ≈ 0.2 to x ≈ 1.1. On the basis of the NMR data and of the analysis of the X-ray patterns of gels and powders, it is inferred that the ZP(Cn)x compounds have an α-type layered structure and that the reaction between α-ZrP and H2Cn is a topotactic anion exchange process. The evolution of the X-ray patterns during propanol deintercalation is consistent with a random distribution of the alkylphosphonate groups on the α-type layers which gives rise to porous pathways in the interlayer region. To test the possibility of using ZP(Cn)x as mechanical reinforcement of a polymer matrix, a starch membrane filled with 5 wt % ZP(C6)0.54 was prepared and characterized by stress-strain mechanical tests. Besides an excellent flexibility, this membrane exhibited a proportional increase of the Young's modulus by 230% in comparison with neat starch.

Immobilization of Alendronate on Zirconium Phosphate Nanoplatelets.

Different amounts of sodium-alendronate (ALN) were loaded into layered zirconium phosphates of alpha and gamma type (αZP and γZP) by means of topotactic exchange reactions of phosphate with ALN. In order to extend the exchange process to the less accessible interlayer regions, ALN solutions were contacted with colloidal dispersions of the layered solids previously exfoliated in single sheets by means of intercalation reaction of propylamine (for αZP) or acetone (for γZP). The ALN loading degree was determined by liquid P-nuclear magnetic resonance (NMR) and inductively coupled plasma (ICP), and it was reported as ALN/Zr molar ratios (Rs). The maximum R obtained for γZP was 0.34, while αZP was able to load a higher amount of ALN, reaching Rs equal to 1. The synthesized compounds were characterized by X-ray powder diffractometry, scanning electron microscopy (SEM), solid-state NMR, and infrared spectroscopy. The way the grafted organo-phosphonate groups were bonded to the layers of the host structure was suggested. The effect of ZP derivatives was assessed on cell proliferation, and the results showed that after 7 days of incubation, none of the samples showed a decrease in cell proliferation.

Alginate Ag/AgCl Nanoparticles Composite Films for Wound Dressings with Antibiofilm and Antimicrobial Activities.

Recently, silver-based nanoparticles have been proposed as components of wound dressings due to their antimicrobial activity. Unfortunately, they are cytotoxic for keratinocytes and fibroblasts, and this limits their use. Less consideration has been given to the use of AgCl nanoparticles in wound dressings. In this paper, a sustainable preparation of alginate AgCl nanoparticles composite films by simultaneous alginate gelation and AgCl nanoparticle formation in the presence of CaCl2 solution is proposed with the aim of obtaining films with antimicrobial and antibiofilm activities and low cytotoxicity. First, AgNO3 alginate films were prepared, and then, gelation and nanoparticle formation were induced by film immersion in CaCl2 solution. Films characterization revealed the presence of both AgCl and metallic silver nanoparticles, which resulted as quite homogeneously distributed, and good hydration properties. Finally, films were tested for their antimicrobial and antibiofilm activities against Staphylococcus epidermidis (ATCC 12228), Staphylococcus aureus (ATCC 29213), Pseudomonas aeruginosa (ATCC 15692), and the yeast Candida albicans. Composite films showed antibacterial and antibiofilm activities against the tested bacteria and resulted as less active towards Candida albicans. Film cytotoxicity was investigated towards human dermis fibroblasts (HuDe) and human skin keratinocytes (NCTC2544). Composite films showed low cytotoxicity, especially towards fibroblasts. Thus, the proposed sustainable approach allows to obtain composite films of Ag/AgCl alginate nanoparticles capable of preventing the onset of infections without showing high cytotoxicity for tissue cells.

Survey on the phase transitions and their effect on the ion-exchange and on the proton-conduction properties of a flexible and robust Zr phosphonate coordination polymer.

The flexible zirconium tetraphosphonate coordination polymer with formula Zr(O(3)PCH(2))(2)N-C(6)H(10)-N(O(3)CH(2)P)(2)X(2-x)H(2+x)·nH(2)O (X = H, Li, Na, K, 0 < x < 1, 4 < n < 7.5) (1) possesses an open framework structure with 1D cavities decorated with polar and acids P═O and P-OH groups. 1 has been fully protonated by adding HCl and then subjected to several acid-base ion-exchange reactions with alkaline metals hydroxides. 1 is a very robust coordination polymer because it can be regenerated in H- form using strong acid solutions and ri-exchanged several times without hydrolysis and loss of crystallinity. The flexibility of 1 has been also studied by means of TDXD (temperature dependent X-ray diffraction) evidencing remarkable phase transformations that lead to a different disposition of the water molecules. These transformations also influence the accessibility of the cations on the P-OH groups placed inside the channels and thus the ion-exchange properties. The dependence of the proton conductivity properties on these phase transitions has been also investigated and discussed.

Advances in the chemistry of nanosized zirconium phosphates: a new mild and quick route to the synthesis of nanocrystals.

Simple addition of zirconyl propionate to phosphoric acid in alcoholic media surprisingly led to the formation, in few minutes, of transparent gels containing solvent intercalated zirconium phosphate (ZrP) nanoparticles with hexagonal shape and a planar size of about 40 nm. With the help of elemental analysis, inductively coupled plasma-optical emission spectrometry (ICP-OES), and (31)P magic angle spinning (MAS) NMR, the nanoparticle composition was formulated as Zr(R)(w)(HPO(4))(x)(H(2)PO(4))(y), in which R can be an hydroxyl or a propionate group. The stoichiometric coefficients for propanol intercalated ZrP are x = 1.43, y = 0.83, and w = 0.32. Solvent elimination at 60 °C gave rise to an increase in the x value and a decrease in the y and w values. X-ray powder diffraction analysis and transmission electron microscopy (TEM) observations showed a concomitant increase in the particle size: planar size and thickness ranged from 90 to 200 nm and from 20 to 85 nm, respectively, depending on the nature of the solvent. A possible mechanism explaining the change in the x, y, and w values, the growth of nanoparticles, and the role of the solvent is proposed. Finally, the possibility of using these gels to disperse the ZrP nanoparticles within the polymer matrix of Nafion117 is shown.

Ionic and covalent crosslinking in chitosan-succinic acid membranes: Effect on physicochemical properties.

In this work, chitosan-succinic acid membranes were prepared by casting method and the physicochemical and mechanical properties of non-neutralized and neutralized with NaOH films were compared. Mechanical strength, flexibility, thermal stability and water-vapor permeability of chitosan membranes are significantly improved after neutralization. These improvements could be partly ascribed to the use of a dicarboxylic acid, which decreases the spacing between chitosan chains as a consequence of ionic crosslinking. Moreover, the addition of the strong base to the hydrogel promotes the formation of amide bonds, as suggested by FTIR analysis and demonstrated by acid-base titration. The favorable features of chitosan-succinic acid films as well as the possibility to easily incorporate drugs, enzymes, essential oils or other additives in the hydrogel, make such membranes suitable for many applications.

PVC grafted zinc oxide nanoparticles as an inhospitable surface to microbes.

Antimicrobial Polyvinyl chloride (PVC) was obtained by covalent bonding of zinc oxide nanoparticles, which have gained important achievements in antimicrobial fields because of their auspicious properties. This was achieved by grafting mercaptopropyltrimethoxysilane onto PVC, followed by the growth of zinc oxide nanoparticles covalently bonded on the polymer surface. In this study, the relationship between the physicochemical features of modified-surface PVC and antimicrobial activity on Staphylococcus aureus and Candida albicans was investigated. Zinc oxide with controllable morphologies (rods, rod flowers, and petal flowers) was synthesized on the polymer surface by tuning merely base-type and concentration using a hydrothermal process. The antimicrobial activity was more pronounced for rod flower morphology, because of their differences in microscopic parameters such as specific Zn-polar planes. This work provides an important hint for the safe use of PVC for biomedical devices by the structure surface tuning without injuring polymer bulk properties and a reduced risk of the covalently bonded nanoparticle dispersion in the host and the environment.

Polydopamine Coated CeO2 as Radical Scavenger Filler for Aquivion Membranes with High Proton Conductivity.

CeO2 nanoparticles were coated with polydopamine (PDA) by dopamine polymerization in water dispersions of CeO2 and characterized by Infrared and Near Edge X-ray Absorption Fine Structure spectroscopy, Transmission Electron Microscopy, Thermogravimetric analysis and X-ray diffraction. The resulting materials (PDAx@CeO2, with x = PDA wt% = 10, 25, 50) were employed as fillers of composite proton exchange membranes with Aquivion 830 as ionomer, to reduce the ionomer chemical degradation due to hydroxyl and hydroperoxyl radicals. Membranes, loaded with 3 and 5 wt% PDAx@CeO2, were prepared by solution casting and characterized by conductivity measurements at 80 and 110 °C, with relative humidity ranging from 50 to 90%, by accelerated ex situ degradation tests with the Fenton reagent, as well as by in situ open circuit voltage stress tests. In comparison with bare CeO2, the PDA coated filler mitigates the conductivity drop occurring at increasing CeO2 loading especially at 110 °C and 50% relative humidity but does not alter the radical scavenger efficiency of bare CeO2 for loadings up to 4 wt%. Fluoride emission rate data arising from the composite membrane degradation are in agreement with the corresponding changes in membrane mass and conductivity.

Bioinspired Reactive Interfaces Based on Layered Double Hydroxides-Zn Rich Hydroxyapatite with Antibacterial Activity.

This work is focused on the preparation and multi-technique characterization of potentially biocompatible reactive interfaces obtained by combining layered double hydroxides (LDHs) and hydroxyapatite (HA). Antimicrobial and osteoinductive metallic ions as Zn2+ and Ga3+ were chosen as intralayer constituents of LDH to obtain ZnAl and ZnAlGa systems. These LDHs, exchanged with dihydrogenphosphate anions, promoted the precipitation of HA on the LDH surface yielding HA@LDH composites. X-ray diffraction quantitative analysis, through the Rietveld refinement method, coupled with elemental analysis and micro-Raman spectroscopy showed the formation of a mixed Ca-Zn HA phase. Scanning electron microscopy revealed that HA, in the presence of LDH, grew preferentially along its a-axis, thus crystallizing mainly in the form of flake crystals. LDH and HA@LDH composites showed antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa at not cytotoxic concentrations for human osteoblasts (hFob 1.19), especially when Ga cations were present in the LDH structure. The effect of the presence of HA in the composites on the bone-bonding ability and on human osteoblast proliferation was also investigated. The HA seemed to reduce the toxicity of the LDH toward human osteoblast while did not affect the bone-bonding ability. This multidisciplinary study provides the bio-chemical, structural characterization of new LDH and HA@LDH composites, evaluating also their bioactivity to be potentially applicable to titanium-based prostheses.

Synthesis and characterization of 1,2,4-triazolo[1,5-a]pyrimidine-2-carboxamide-based compounds targeting the PA-PB1 interface of influenza A virus polymerase.

Influenza viruses (Flu) are responsible for seasonal epidemics causing high rates of morbidity, which can dramatically increase during severe pandemic outbreaks. Antiviral drugs are an indispensable weapon to treat infected people and reduce the impact on human health, nevertheless anti-Flu armamentarium still remains inadequate. In search for new anti-Flu drugs, our group has focused on viral RNA-dependent RNA polymerase (RdRP) developing disruptors of PA-PB1 subunits interface with the best compounds characterized by cycloheptathiophene-3-carboxamide and 1,2,4-triazolo[1,5-a]pyrimidine-2-carboxamide scaffolds. By merging these moieties, two very interesting hybrid compounds were recently identified, starting from which, in this paper, a series of analogues were designed and synthesized. In particular, a thorough exploration of the cycloheptathiophene-3-carboxamide moiety led to acquire important SAR insight and identify new active compounds showing both the ability to inhibit PA-PB1 interaction and viral replication in the micromolar range and at non-toxic concentrations. For few compounds, the ability to efficiently inhibit PA-PB1 subunits interaction did not translate into anti-Flu activity. Chemical/physical properties were investigated for a couple of compounds suggesting that the low solubility of compound 14, due to a strong crystal lattice, may have impaired its antiviral activity. Finally, computational studies performed on compound 23, in which the phenyl ring suitably replaced the cycloheptathiophene, suggested that, in addition to hydrophobic interactions, H-bonds enhanced its binding within the PAC cavity.