RESUMO
We investigate the possibility of the optical computation of the Laplace operator in the oblique incidence geometry using a layered structure consisting of a set of homogeneous thin films. For this, we develop a general description of the diffraction of a three-dimensional linearly polarized optical beam by a layered structure at oblique incidence. Using this description, we derive the transfer function of a multilayer structure consisting of two three-layer metal-dielectric-metal structures and possessing a second-order reflection zero with respect to the tangential component of the wave vector of the incident wave. We show that under a certain condition, this transfer function can coincide up to a constant multiplier with the transfer function of a linear system performing the computation of the Laplace operator. Using rigorous numerical simulations based on the enhanced transmittance matrix approach, we demonstrate that the considered metal-dielectric structure can optically compute the Laplacian of the incident Gaussian beam with the normalized root-mean-square error of the order of 1%. We also show that this structure can be effectively utilized for optical edge detection of the incident signal.
RESUMO
We propose and investigate integrated metal-dielectric-metal (MDM) resonators operating with semi-guided waves (guided modes of dielectric slab waveguides). The MDM resonators are constituted by two metal strips "buried" in the waveguide core layer and separated by a dielectric waveguide segment. We theoretically prove and numerically demonstrate that by a proper choice of the mode incidence geometry, the widths of the metal strips, and the distance between them, it is possible to achieve either total absorption of the incident wave or coherent perfect absorption (in the case of symmetric incidence of two modes on the structure). The proposed planar MDM resonators may find application as absorbers or filters in integrated optical circuits.
RESUMO
This erratum includes a necessary additional reference for the article [J. Opt. Soc. Am. A38, 855 (2021)JOAOD60740-323210.1364/JOSAA.425379].
RESUMO
We propose and numerically investigate integrated high-contrast gratings (HCGs) for surface plasmon polaritons (SPPs) propagating along metal-dielectric interfaces, which consist of periodically arranged silicon pillars located on the gold surface. We demonstrate that such on-chip HCGs can be used as broadband plasmonic mirrors, which have subwavelength footprint in the SPP propagation direction and mean reflectance exceeding 85% in a 200-nm-wide spectral range for both the cases of normal and oblique SPP incidence. In order to increase the HCG efficiency and design practically feasible structures, we utilize a parasitic scattering suppression technique based on the use of two-layer grating pillars. The presented results may find application in two-dimensional optical circuits for steering the SPP propagation.
RESUMO
We propose a method for designing a refractive optical element with two working surfaces transforming an incident beam with a plane wavefront into an output beam with prescribed irradiance distribution and a non-planar wavefront. The presented method generalizes the supporting quadric method [Opt. Express28, 22642 (2020)10.1364/OE.398990] proposed for collimated beam shaping to the case of a non-planar output wavefront. The method is simple to implement and is based on just a few main equations. We present several examples of designing optical elements (including elements with piecewise-smooth optical surfaces) generating light beams with prescribed irradiance distributions and wavefronts (spherical and aspherical). The examples demonstrate high performance of the method.
RESUMO
Hybrid methods combining the geometrical-optics and diffraction-theory methods enable designing diffractive optical elements (DOEs) with high performance due to the suppression of stray light and speckles and, at the same time, with a regular and fabrication-friendly microrelief. Here, we propose a geometrical-optics method for calculating the eikonal function of the light field providing the generation of a required irradiance distribution. In the method, the problem of calculating the eikonal function is formulated in a semi-discrete form as a problem of maximizing a concave function. For solving the maximization problem, a gradient method is used, with analytical expressions obtained for the gradient. In contrast to geometrical-optics approaches based on solving the Monge-Ampére equation using finite difference methods, the proposed method enables generating irradiance distributions defined on disconnected regions with non-smooth boundaries. As an example, we calculate an eikonal function, which provides the generation of a "discontinuous" irradiance distribution in the form of a hexagram. It is shown that the utilization of the hybrid approach, in which the obtained geometrical-optics solution is used as a starting point in iterative Fourier transform algorithms, enables designing DOEs with a quasi-regular or piecewise-smooth microrelief structure. The calculation results are confirmed by the results of experimental investigations of a DOE generating a hexagram-shaped irradiance distribution.
RESUMO
We present a method for designing lenses with two aspherical surfaces having minimal Fresnel losses among the class of stigmatic lenses. Minimization of Fresnel losses is achieved by ensuring equal ray deviation angles on the lens surfaces. Calculation of lenses with minimal Fresnel losses is reduced to solving an explicit ordinary differential equation. Simple analytical approximations are also obtained for the lens profiles.
RESUMO
We consider a method for designing stigmatic lenses implementing required ray mappings. A ray mapping relates the angular coordinates of the rays at the image points with the angular coordinates of the rays coming from the object. The calculation of a stigmatic lens with a required ray mapping is reduced to solving an explicit ordinary differential equation. As examples, we design stigmatic lenses satisfying the Abbe sine condition, the Herschel's condition, and the constant angular magnification condition.
RESUMO
We propose a version of the supporting quadric method for calculating a refractive optical element with two working surfaces for collimated beam shaping. Using optimal mass transportation theory and generalized Voronoi cells, we show that the proposed method can be regarded as a gradient method of maximizing a concave function, which is a discrete analogue of the Lagrange functional in the corresponding mass transportation problem. It is demonstrated that any maximum of this function provides a solution to the problem of collimated beam shaping. Therefore, the proposed method does not suffer from "trapping" at a local extremum, which is typical for gradient methods. We present design examples of refractive optical elements illustrating high performance of the method.
RESUMO
We propose a method for designing optical elements with two freeform refracting surfaces generating prescribed non-axisymmetric irradiance distributions in the case of an extended light source. The method is based on the representation of the optical surfaces as bicubic splines and on the subsequent optimization of their parameters using a quasi-Newton method. For the fast calculation of the merit function, we propose an efficient version of the ray tracing method. Using the proposed approach, we design optical elements generating uniform square-shaped irradiance distributions in the far- and near-field. The designed elements are very compact (the height-to-source ratio is only 1.6) and, while providing a high lighting efficiency of 89%, generate highly uniform distributions (the ratio between minimum and average irradiance values in the prescribed square-shaped region exceeds 0.9).
RESUMO
We propose a method for designing diffractive lenses having a fixed-position focus at several prescribed wavelengths, which we refer to as spectral diffractive lenses (SDLs). The method is based on minimizing an objective function describing the deviation of the complex transmission functions of the spectral lens at the operating wavelengths from the complex transmission functions of diffractive lenses calculated separately for each of these wavelengths. As examples, SDLs operating at three, five, and seven different wavelengths are designed. The simulation results of the calculated lenses confirm high efficiency of the proposed method. For experimental verification of the design method, we fabricate using direct laser writing and experimentally investigate an SDL operating at five wavelengths. The presented experimental results confirm the efficiency of the proposed method in practical problems of designing SDLs. The obtained results may find applications in the design and fabrication of novel flat diffractive lenses with reduced chromatic effects.
RESUMO
We propose integrated Gires-Tournois interferometers (GTIs) for guided modes of dielectric slab waveguides. The proposed GTIs consist of one or several dielectric ridge resonators separated by subwavelength-width grooves patterned into an abruptly terminated slab waveguide and operate at oblique incidence of the fundamental transverse-electric-polarized mode. The grooves act as partially reflective mirrors, whereas the end facet of the last ridge works in the total internal reflection regime and reflects all the incident radiation. We show that the single-ridge structure provides a nonlinear staircase-like phase response characteristic for GTIs. By using several properly arranged ridges, one can engineer group delay or group delay dispersion in a required spectral range. As an example, we design a three-ridge GTI providing an almost constant group delay dispersion in a 50-nm-wide wavelength range. The proposed planar GTIs may find application in integrated optical circuits for introducing or compensating for chromatic dispersion.
RESUMO
We propose a multiscale approach for designing mirrors generating prescribed irradiance distributions in the far field. Our design method is based on calculating a ray mapping from a Monge-Kantorovich mass transportation problem and on reducing this problem to a linear assignment problem (LAP). The proposed multiscale formulation of the LAP allows one to efficiently calculate freeform mirror surfaces defined on meshes with a size of up to at least 1000×1000. As an example requiring a mesh of this size, we design a mirror generating a grayscale image of A. Einstein on a zero background. The proposed multiscale approach is general and can be applied to a wide range of inverse problems of nonimaging optics.
RESUMO
We consider a method for designing freeform mirrors generating prescribed irradiance distributions in the far field. The method is based on the formulation of the problem of calculating a ray mapping as a Monge-Kantorovich mass transportation problem and on the reduction of the latter problem to a linear assignment problem. As examples, we design freeform mirrors generating a uniform irradiance distribution in a rectangular region and a complex chessboard-shaped distribution. The mirror generating a rectangular irradiance distribution is fabricated and experimentally investigated. The experimental results are in good agreement with the numerical simulations and confirm the manufacturability of the mirrors designed using the considered method.
RESUMO
We consider the problem of calculating a refractive surface generating a prescribed irradiance distribution in the far field in the case of a point light source. We show that this problem can be formulated as a mass transportation problem with a non-quadratic cost function. A method for calculating the refractive surface is proposed, which is based on reducing the problem of calculating an integrable ray mapping to finding a solution to a linear assignment problem. We discuss the application of the developed method for the design of optical elements with two "working" refractive surfaces. The method was applied to the calculation of refractive optical elements generating uniform irradiance distributions in a square and in a region in the form of the letters "AB" on a zero background. The results of the simulations of the designed optical elements demonstrate high performance of the proposed method.
RESUMO
Resonant properties of composite structures consisting of several identical resonant structures (e.g. multilayer thin-film structures or guided-mode resonance gratings) separated by phase-shift layers are investigated theoretically. Using the scattering matrix formalism, we analytically demonstrate that, at properly chosen thicknesses of the phase-shift layers, the composite structures comprising two or four resonant diffractive structures with a Lorentzian transmittance profile optically implement the Butterworth filters of the order two or three, respectively, and enable achieving flat-top transmission spectra with steep slopes and low sidebands. In addition, we show that the composite structures consisting of three or four second-order Butterworth filters can accurately approximate the fourth- or fifth-order Butterworth filters, respectively. The presented theoretical results are confirmed by rigorous numerical simulations of composite structures consisting of the so-called W-structures (simple three-layer resonant structures comprising a high-index core layer and two low-index cladding layers in a high-index dielectric environment). The simulation results confirm the formation of flat-top transmittance peaks, the shape of which fully agrees with the derived theoretical description. Moreover, we demonstrate an exceptionally simple mechanism of controlling the transmittance peak width, which consists in changing the thicknesses of the cladding layers of the initial W-structure and enables generating flat-top transmission peaks with a significantly subnanometer width.
RESUMO
We theoretically and numerically investigate resonant optical properties of composite structures consisting of several subwavelength resonant diffraction gratings separated by homogeneous layers. Using the scattering matrix formalism, we demonstrate that the composite structure comprising N gratings has a multiple transmittance zero of the order N. We show that at the distance between the gratings satisfying the Fabry-Pérot resonance condition, an (N - 1)-degenerate bound state in the continuum (BIC) is formed. The results of rigorous numerical simulations fully confirm the theoretically predicted formation of multiple zeros and BICs in the composite structures. Near the BICs, an effect very similar to the electromagnetically induced transparency is observed. We show that by making the proper choice of the thicknesses of the layers separating the gratings, nearly rectangular reflectance or transmittance peaks with steep slopes and virtually no sidelobes can be obtained. In particular, one of the presented examples demonstrates the possibility of obtaining an approximately rectangular transmittance peak with a significantly subnanometer width. The presented results may find application in the design of optical filters, sensors and devices for optical differentiation and transformation of optical signals.
RESUMO
We consider the problem of calculating a refracting surface generating a prescribed irradiance distribution in the far field in the case of a plane incident beam. We demonstrate that this problem can be formulated as a mass transportation problem (MTP) and obtain the cost function for the MTP. It is shown that with a special choice of coordinates, the cost function becomes quadratic. The obtained mass transportation problem also describes the problem of calculating a mirror, which can be considered as a special case of the problem of calculating a refracting surface. We propose a method of calculating a refracting surface based on the reduction of the MTP to a linear assignment problem. This method is applied to the design of several optical elements generating prescribed intensity distributions. The simulation results demonstrate high performance of the proposed approach.
RESUMO
It has been shown in [Arch. Rational Mechanics and Analysis 201, 1013 (2011)]. Such approach provides a rigorous methodology for designing freeform optics for irradiance redistribution. In this paper, this approach is applied to design of a laser beam shaping system with two lenses.
RESUMO
We propose a method for designing refractive optical elements for collimated beam shaping in the geometrical optics approximation. In this method, the problem of finding a ray mapping is formulated as a linear assignment problem, which is a discrete version of the corresponding mass transportation problem. A method for reconstructing optical surfaces from a computed discrete ray mapping is proposed. The method is suitable for designing continuous piecewise-smooth optical surfaces. The design of refractive optical elements transforming beams with circular cross-section to variously shaped (rectangular, triangular, and cross-shaped) beams with plane wavefront is discussed. The presented numerical simulation results confirm high efficiency of the designed optical elements.