RESUMO
Metal-based aerogels have attracted numerous studies due to their unique physical, structural, thermal, and chemical properties. Utilizing aluminum waste, a novel, facile, environmentally friendly approach to aluminum-based aerogels is proposed. In this work, the aluminum-based aerogels produced do not use toxic chemicals unlike conventional aerogel production. Aluminum powder, with poly(acrylic acid) and carboxymethyl cellulose as binders, is converted into aluminum-based aerogels using the freeze-drying method. The aluminum-based aerogels have low density (0.08-0.12 g/cm3) and high porosity (93.83-95.68%). The thermal conductivity of the aerogels obtained is very low (0.038-0.045 W/m·K), comparable to other types of aerogels and commercial heat insulation materials. Additionally, the aerogels can withstand temperatures up to 1000 °C with less than 40% decomposition. The aerogels exhibited promising oil absorption properties with their absorption capacity of 9.8 g/g and 0.784 g/cm3. The Young's modulus of the aerogels ranged from 70.6 kPa to 330.2 kPa. This study suggests that aluminum-based aerogels have potential in thermal insulation and oil absorption applications.
RESUMO
Single-walled carbon nanotubes (SWNTs) are promising heating agents in cancer photothermal therapy when under near infrared radiation, yet few efforts have been focused on the quantitative understanding of the photothermal energy conversion in biological systems. In this article, a mesoscopic study that takes into account SWNT morphologies (diameter and aspect ratio) and dispersions (orientation and concentration), as well as thermal boundary resistance, is performed by means of an off-lattice Monte Carlo simulation. Results indicate that SWNTs with orientation perpendicular to the laser, smaller diameter and better dispersion have higher heating efficiency in cancer photothermal therapy. Thermal boundary resistances greatly inhibit thermal energy transfer away from SWNTs, thereby affecting their heating efficiency. Through appropriate interfacial modification around SWNTs, compared to the surrounding healthy tissue, a higher temperature of the cancer cell can be achieved, resulting in more effective cancer photothermal therapy. These findings promise to bridge the gap between macroscopic and microscopic computational studies of cancer photothermal therapy.
Assuntos
Simulação por Computador , Hipertermia Induzida , Raios Infravermelhos/uso terapêutico , Nanotubos de Carbono , Neoplasias/terapia , Fototerapia , Humanos , Método de Monte CarloRESUMO
Tons of waste from residential, commercial and manufacturing activities are generated due to the growing population, urbanization and economic development, prompting the need for sustainable measures. Numerous ways of converting waste to aerogels, a novel class of ultra-light and ultra-porous materials, have been researched to tackle the issues of waste. This review provides an overview of the status of aerogels made from agricultural waste, municipal solid, and industrial waste focusing on the fabrication, properties, and applications of such aerogels. The review first introduced common methods to synthesize the aerogels from waste, including dispersion and drying techniques. Following that, numerous works related to aerogels from waste are summarized and compared, mainly focusing on the sustainability aspect of the processes involved and their contributions for environmental applications such as thermal insulation and oil absorption. Next, advantages, and disadvantages of the current approaches are analyzed. Finally, some prospective waste aerogels and its applications are proposed.
RESUMO
Single-atom catalysts (SACs) offer many advantages, such as atom economy and high chemoselectivity; however, their practical application in liquid-phase heterogeneous catalysis is hampered by the productivity bottleneck as well as catalyst leaching. Flow chemistry is a well-established method to increase the conversion rate of catalytic processes, however, SAC-catalysed flow chemistry in packed-bed type flow reactor is disadvantaged by low turnover number and poor stability. In this study, we demonstrate the use of fuel cell-type flow stacks enabled exceptionally high quantitative conversion in single atom-catalyzed reactions, as exemplified by the use of Pt SAC-on-MoS2/graphite felt catalysts incorporated in flow cell. A turnover frequency of approximately 8000 h-1 that corresponds to an aniline productivity of 5.8 g h-1 is achieved with a bench-top flow module (nominal reservoir volume of 1 cm3), with a Pt1-MoS2 catalyst loading of 1.5 g (3.2 mg of Pt). X-ray absorption fine structure spectroscopy combined with density functional theory calculations provide insights into stability and reactivity of single atom Pt supported in a pyramidal fashion on MoS2. Our study highlights the quantitative conversion bottleneck in SAC-mediated fine chemicals production can be overcome using flow chemistry.
RESUMO
Interfaces dominate the thermal resistances in aligned carbon nanotube arrays. This work uses nanosecond thermoreflectance thermometry to separate interface and volume resistances for 10 microm thick aligned SWNT films coated with Al, Ti, Pd, Pt, and Ni. We interpret the data by defining the nanotube-metal engagement factor, which governs the interface resistance and is extracted using the measured film heat capacity. The metal-SWNT and SWNT-substrate resistances range between 3.8 and 9.2 mm(2)K/W and 33-46 mm(2)K/W, respectively. The temperature dependency of the heat capacity data, measured between 125 and 300 K, is in good agreement with theoretical predictions. The temperature dependence demonstrated by the metal-SWNT interface resistance data suggests inelastic phonon transmission.
RESUMO
Massive quantities of fly ash are produced worldwide from thermal power plants, posing a serious environmental threat due to their storage and disposal problems. In this study, for the first time, fly ash is converted into an advanced and novel aerogel through a green and eco-friendly process. The developed aerogel has a low density of 0.10-0.19 g cm-3, a high porosity of up to 90%, a low thermal conductivity of 0.042-0.050 W/mK, and a good sound absorption coefficient (noise reduction coefficient [NRC] value of 0.20-0.30). It also shows a high compressive Young's modulus of up to 150 kPa. Therefore, the newly developed fly ash aerogel is a potential material for thermal and acoustic insulation applications, along with lightweight composites in automotive and aerospace applications.
Assuntos
Cinza de Carvão , Centrais Elétricas , Acústica , Porosidade , Condutividade TérmicaRESUMO
A promising and economic material for various applications, such as thermal insulation in construction building and oil clean-up in marine ecosystems, is successfully developed from the by-product of the sugarcane industry. Biodegradable sugarcane bagasse aerogels are produced using polyvinyl alcohol (PVA) binder, followed by a freeze-drying method. This environmental-friendly recycled aerogel has an ultra-low density ([0.016-0.112] g/cm3), a high porosity ([91.9-98.9]%), and a very low thermal conductivity ([0.031-0.042] W/mK). Its superhydrophobicity properties and its maximum oil absorption capacity (up to 25 g/g) are measured after coating aerogel samples with methyltrimethoxysilane (MTMS). The biodegradable aerogel has a Young's modulus of 88 K Pa and can be bent without breaking, demonstrating its high flexibility.
RESUMO
Directional thermal conductivities of aligned carbon nanotube (CNT) polymer nanocomposites were calculated using a random walk simulation with and without inter-CNT contact effects. The CNT contact effect has not been explored for its role in thermal transport, and it is shown here to significantly affect the effective transport properties including anisotropy ratios. The primary focus of the paper is on the non-isotropic heat conduction in aligned-CNT polymeric composites, because this geometry is an ideal thermal layer as well as constituting a representative volume element of CNT-reinforced polymer matrices in hybrid advanced composites under development. The effects of CNT orientation, type (single-versus multi-wall), inter-CNT contact, volume fraction and thermal boundary resistance on the effective conductivities of CNT composites are quantified. It is found that when the CNT-CNT thermal contact is taken into account, the maximum effective thermal conductivity of the nanocomposites having their CNTs parallel to the heat flux decreases by approximately 4 times and approximately 2 times for the single-walled and the multi-walled CNTs, respectively, at 20% CNT volume fraction.
RESUMO
Millions of tons of plastic are produced annually, but less than 10% are reported to be recycled. This work sets out to transform environmental plastic (polyethylene terephthalate - PET) waste into aerogels for high-value engineering applications, primarily to enhance the monetary incentive in recycling plastics. Coating techniques, using silicone ceramic (SCC) and (3-aminopropyl)triethoxysilane (APS, or APTES) solutions, are successfully devised to enhance the thermal stability and CO2 adsorption capability of rPET aerogel. The rPET/SCC aerogel exhibits improved thermal stability (up to 600⯰C), enhanced thermal insulation (thermal conductivity Kavgâ¯=â¯[31.8-34.9] mW/m·K), hydrophobic characteristics (up to 144.7° in contact angle) and enhanced rigidity (Young modulus Eavgâ¯=â¯[4.5-124.8] kPa), while maintaining an ultra-low density (ρaâ¯=â¯[14-62] g/cm3) and a high porosity (Φavgâ¯=â¯[95.6-99.0]%). Moreover, the amine-functionalised rPET aerogel achieves a CO2 adsorption capacity of up to 0.44â¯mmol CO2/g, superior to several commercial physio-sorbents. These promising results obtained demonstrate that the rPET aerogel is a versatile material suitable for a wide variety of high-value engineering applications, including thermal insulation and direct CO2 capture applications.
Assuntos
Polietilenotereftalatos , Reciclagem , Interações Hidrofóbicas e Hidrofílicas , Porosidade , Condutividade TérmicaRESUMO
This work presents for the first time, a simple, practical and scalable approach to fabricating recycled polyethylene terephthalate (rPET) aerogels for thermal and acoustic insulation applications. The rPET aerogels were successfully developed from recycled PET fibers and polyvinyl alcohol (PVA) and glutaraldehyde (GA) cross-linkers using a freeze-drying process. The effects of various PET fiber concentrations (0.5, 1.0 and 2.0 by wt.%), fiber deniers (3D, 7D and 15D) and fiber lengths (32 mm and 64 mm) on the rPET aerogel structures and multi-properties were comprehensively investigated. The developed rPET aerogels showed a highly porous network structure (98.3â»99.5%), ultra-low densities (0.007â»0.026 g/cm³), hydrophobicity with water contact angles of 120.7â»149.8°, and high elasticity with low compressive Young's modulus (1.16â»2.87 kPa). They exhibited superior thermal insulation capability with low thermal conductivities of 0.035â»0.038 W/m.K, which are highly competitive with recycled cellulose and silica-cellulose aerogels and better than mineral wool and polystyrene. The acoustic absorption results were also found to outperform a commercial acoustic foam absorber across a range of frequencies.
RESUMO
Graphene aerogels (GAs) have attracted extensive interest in diverse fields, owing to their ultrahigh surface area, low density and decent electrical conductivity. However, the undesirable thermal conductivity of GAs may limit their applications in energy storage devices. Here, we report a facile hydrothermal method to modulate both the electrical and thermal properties of GAs by including bulk molybdenum disulfide (MoS2). It was found that MoS2 can help to reduce the size of graphene sheets and improve their dispersion, leading to the uniform porous micro-structure of GAs. The electrical measurement showed that the electrical conductivity of GAs could be decreased by 87% by adding 0.132 vol % of MoS2. On the contrary, the thermal conductivity of GAs could be increased by ~51% by including 0.2 vol % of MoS2. The quantitative investigation demonstrated that the effective medium theories (EMTs) could be applied to predict the thermal conductivity of composite GAs. Our findings indicated that the electrical and thermal properties of GAs can be tuned for the applications in various fields.
RESUMO
In this study, we apply a simple but effective oxidative purification method to purify carbon nanotube (CNT) fibers synthesized via a floating catalyst technique. After the purification treatment, the resulting CNT fibers exhibited significant improvements in mechanical and electrical properties with an increase in strength, Young's modulus, and electrical conductivity by approximately 81, 230, and 100%, respectively. With the successful dissolution of the CNT fibers in superacid, an extensional viscosity method could be applied to measure the aspect ratio of the CNTs constituting the fibers, whereas high-purity CNT thin films could be produced with a low resistance of 720 Ω/sq at a transmittance of 85%. This work suggests that the oxidative purification approach and dissolution process are promising methods to improve the purity and performance of CNT macroscopic structures.
RESUMO
Here, we present a review of recent developments for an off-lattice Monte Carlo approach used to investigate the thermal transport properties of multiphase composites with complex structure. The thermal energy was quantified by a large number of randomly moving thermal walkers. Different modes of heat conduction were modeled in appropriate ways. The diffusive heat conduction in the polymer matrix was modeled with random Brownian motion of thermal walkers within the polymer, and the ballistic heat transfer within the carbon nanotubes (CNTs) was modeled by assigning infinite speed of thermal walkers in the CNTs. Three case studies were conducted to validate the developed approach, including three-phase single-walled CNTs/tungsten disulfide (WS2)/(poly(ether ether ketone) (PEEK) composites, single-walled CNT/WS2/PEEK composites with the CNTs clustered in bundles, and complex graphene/poly(methyl methacrylate) (PMMA) composites. In all cases, resistance to heat transfer due to nanoscale phenomena was also modeled. By quantitatively studying the influencing factors on the thermal transport properties of the multiphase composites, it was found that the orientation, aggregation and morphology of fillers, as well as the interfacial thermal resistance at filler-matrix interfaces would limit the transfer of heat in the composites. These quantitative findings may be applied in the design and synthesis of multiphase composites with specific thermal transport properties.
RESUMO
We investigated the effects of the synthesis conditions and condensation processes on the chemical compositions and multifunctional performance of the directly spun carbon nanotube (CNT) fibers. On the basis of the optimized synthesis conditions, a two-step post-treatment technique which involved acidification and epoxy infiltration was also developed to further enhance their mechanical and electrical properties. As a result, their tensile strength and Young's modulus increased remarkably by 177% and 325%, respectively, while their electrical conductivity also reached 8235 S/cm. This work may provide a general strategy for the postprocessing optimization of the directly spun CNT fibers. The treated CNT fibers with superior properties are promising for a wide range of applications, such as structural reinforcements and lightweight electric cables.
RESUMO
Rechargeable lithium ion batteries have ruled the consumer electronics market for the past 20 years and have great significance in the growing number of electric vehicles and stationary energy storage applications. However, in addition to concerns about electrochemical performance, the limited availability of lithium is gradually becoming an important issue for further continued use and development of lithium ion batteries. Therefore, a significant shift in attention has been taking place towards new types of rechargeable batteries such as sodium-based systems that have low cost. Another important aspect of sodium battery is its potential compatibility with the all-solid-state design where solid electrolyte is used to replace liquid one, leading to simple battery design, long life span, and excellent safety. The key to the success of all-solid-state battery design is the challenge of finding solid electrolytes possessing acceptable high ionic conductivities at room temperature. Herein, we report a novel sodium superionic conductor with NASICON structure, Na3.1Zr1.95Mg0.05Si2PO12 that shows high room-temperature ionic conductivity of 3.5 × 10(-3) S cm(-1). We also report successful fabrication of a room-temperature solid-state Na-S cell using this conductor.
RESUMO
The production of continuous carbon nanotube (CNT) fibers and films has paved the way to leverage the superior properties of individual carbon nanotubes for novel macroscale applications such as electronic cables and multifunctional composites. In this manuscript, we synthesize fibers and films from CNT aerogels that are continuously grown by floating catalyst chemical vapor deposition (FCCVD) and measure thermal conductivity and natural convective heat transfer coefficient from the fiber and film. To probe the mechanisms of heat transfer, we develop a new, robust, steady-state thermal characterization technique that enables measurement of the intrinsic fiber thermal conductivity and the convective heat transfer coefficient from the fiber to the surrounding air. The thermal conductivity of the as-prepared fiber ranges from 4.7 ± 0.3 to 28.0 ± 2.4 W m(-1) K(-1) and depends on fiber volume fraction and diameter. A simple nitric acid treatment increases the thermal conductivity by as much as a factor of â¼3 for the fibers and â¼6.7 for the thin films. These acid-treated CNT materials demonstrate specific thermal conductivities significantly higher than common metals with the same absolute thermal conductivity, which means they are comparatively lightweight, thermally conductive fibers and films. Beyond thermal conductivity, the acid treatment enhances electrical conductivity by a factor of â¼2.3. Further, the measured convective heat transfer coefficients range from 25 to 200 W m(-2) K(-1) for all fibers, which is higher than expected for macroscale materials and demonstrates the impact of the nanoscale CNT features on convective heat losses from the fibers. The measured thermal and electrical performance demonstrates the promise for using these fibers and films in macroscale applications requiring effective heat dissipation.
RESUMO
A computational model was developed to study the thermal conductivity of single-walled carbon nanotube (SWNT)-polymer composites. A random walk simulation was used to model the effect of interfacial resistance on the heat flow in different orientations of SWNTs dispersed in the polymers. The simulation is a modification of a previous model taking into account the numerically determined thermal equilibrium factor between the SWNTs and the composite matrix material. The simulation results agreed well with reported experimental data for epoxy and polymethyl methacrylate (PMMA) composites. The effects of the SWNT orientation, weight fraction and thermal boundary resistance on the effective conductivity of composites were quantified. The present model is a useful tool for the prediction of the thermal conductivity within a wide range of volume fractions of the SWNTs, so long as the SWNTs are not in contact with each other. The developed model can be applied to other polymers and solid materials, possibly even metals.