Scale-up issues for commercial depth filters in bioprocessing.

Significant increases in cell density and product titer have led to renewed interest in the application of depth filtration for initial clarification of cell culture fluid in antibody production. The performance of these depth filters will depend on the local pressure and velocity distribution within the filter capsule, but these are very difficult to probe experimentally, leading to challenges in both process design and scale-up. We have used a combination of carefully designed experimental studies and computational fluid dynamics (CFD) to examine these issues in both lab-scale (SupracapTM 50) and pilot-scale (StaxTM ) depth filter modules, both employing dual-layer lenticular PDH4 media containing diatomaceous earth. The SupracapTM 50 showed a more rapid increase in transmembrane pressure and a more rapid DNA breakthrough during filtration of a Chinese Hamster Ovary cell culture fluid. These results were explained using CFD calculations which showed very different flow distributions within the modules. CFD predictions were further validated using measurements of the residence time distribution and dye binding in both the lab-scale and pilot-plant modules. These results provide important insights into the factors controlling the performance and scale-up of these commercially important depth filters as well as a framework that can be broadly applied to develop more effective depth filters and depth filtration processes.

An ultra scale-down method to investigate monoclonal antibody processing during tangential flow filtration using ultrafiltration membranes.

The availability of material for experimental studies is a key constraint in the development of full-scale bioprocesses. This is especially true for the later stages in a bioprocess sequence such as purification and formulation, where the product is at a relatively high concentration and traditional scale-down models can require significant volumes. Using a combination of critical flow regime analysis, bioprocess modelling, and experimentation, ultra scale-down (USD) methods can yield bioprocess information using only millilitre quantities before embarking on highly demanding full-scale studies. In this study the performance of a pilot-scale tangential flow filtration (TFF) system based on a membrane flat-sheet cassette using pumped flow was predicted by devising an USD device comprising a stirred cell using a rotating disc. The USD device operates with just 2.1 cm2 of membrane area and, for example, just 1.7 mL of feed for diafiltration studies. The novel features of the design involve optimisation of the disc location and the membrane configuration to yield an approximately uniform shear rate. This is characterised using computational fluid dynamics for a defined layer above the membrane surface. A pilot-scale TFF device operating at ~500-fold larger feed volume and membrane area was characterised in terms of the shear rate derived from flow rate-pressure drop relationships for the cassette. Good agreement was achieved between the USD and TFF devices for the flux and resistance values at equivalent average shear rates for a monoclonal antibody diafiltration stage.

Streamlining process characterization efforts using the high throughput ambr® crossflow system for ultrafiltration and diafiltration processing of monoclonal antibodies.

Commercial process development for biopharmaceuticals often involves process characterization (PC) studies to gain process knowledge and understanding in preparation for process validation. One common approach to conduct PC activities is by using design-of-experiment, which can help determine the impact process parameter deviations may have on product quality attributes. Qualified scale-down systems are typically used to conduct these studies. For an ultrafiltration/diafiltration (UF/DF) application, however, a traditional scale-down still requires hundreds of milliliters of material per run and can only conduct one experiment at a time. This poses a challenge in resources as there could be 20+ experiments required for a typical UF/DF PC study. One solution to circumvent this is the use of high-throughput systems, which enable parallel experimentation by only using a fraction of the resources. Sartorius Stedim Biotech has recently commercialized the ambr® crossflow high-throughput system to meet this need. In this study, the performance of this system during a monoclonal antibody UF/DF step was first compared with a pilot- and a manufacturing-scale tangential flow filtration (TFF) system at a single operating condition. Due to material limitations, it was then compared to only the pilot-scale TFF system across wider ranges of transmembrane pressure; crossflow rate; and diafiltration concentration in a PC study. Permeate flux, aggregate content, process yield, pH/conductivity traces, retentate concentration, axial pressure drop, and turbidity values were measured at both scales. A good agreement was attained across scales, further supporting its potential use as a scale-down system.

High throughput screening of ultrafiltration and diafiltration processing of monoclonal antibodies via the ambr® crossflow system.

As the biopharmaceutical industry moves toward high concentration of monoclonal antibody drug substance, additional development is required early on when material is still limited. A key constraint is the availability of predictive high-throughput low-volume filtration screening systems for bioprocess development. This particularly impacts final stages such as ultrafiltration/diafiltration steps where traditional scale-down systems need hundreds of milliliters of material per run. Recently, the ambr® crossflow system has been commercialized by Sartorius Stedim Biotech (SSB) to meet this need. It enables parallel high throughput experimentation by only using a fraction of typical material requirements. Critical parameters for predictive filtration systems include loading, mean transmembrane pressure (Δ P¯TMP ), and crossflow rate (QF ). While axial pressure drop (ΔPaxial ) across the cartridge is a function of these parameters, it plays a key role and similar values should result across scales. The ambr® crossflow system is first presented describing typical screening experiments. Its performance is then compared to a traditional pilot-scale tangential flow filtration (TFF) at defined conditions. The original ambr® crossflow (CF) cartridge underperformed resulting in ~20x lower ΔPaxial than the pilot-scale TFF flat-sheet cassette. With an objective to improve the scalability of the system, efforts were made to understand this scale difference. The ambr® CF cartridge was successfully modified by restricting the flow of the feed channel, and thus increasing its ΔPaxial . Additional studies across a range of loading (100-823 gm-2 ); Δ P¯TMP (12-18 psi); and QF (4-8 L/min/m2 ) were conducted in both scales. Comparable flux and aggregate levels were achieved.