A biomechanical comparison of fixed angle locking compression plate osteosynthesis and cement augmented screw osteosynthesis in the management of intra articular calcaneal fractures.

PURPOSE: The purpose of this study was to investigate whether cement-augmented screw osteosynthesis results in stability comparable to conventional fixed-angle locking plate osteosynthesis using cadaveric bones to model a Sanders type 2B fracture. METHODS: Seven pairs of fresh frozen human calcanei and the corresponding tali were used. The specimens were assigned pairwise to two study groups in a randomised manner. In order to determine the initial quasi-static stiffness of the bone-implant construct, testing commenced with quasi-static compression ramp loading; subsequently, sinusoidal cyclic compression loading at 2 Hz was performed until construct failure occurred. Initial dynamic stiffness (cycle 1), range of motion (ROM), cycles to failure and load to failure were determined from the machine data during the cyclic test. In addition, at 250-cycle intervals, Böhler's angle and the critical angle of Gissane were determined on mediolateral X-rays shot with a triggered C-arm; 5° angle flattening was arbitrarily defined as a failure criterion. RESULTS: Bone mineral density was normally distributed without significant differences between the groups. The augmented screw osteosynthesis resulted in higher stiffness values compared to the fixed-angle locking plate osteosynthesis. The fracture fragment motion in the locking plate group was significantly higher compared to the group with augmented screw osteosynthesis. CONCLUSIONS: The results of this study indicate that in our selected test set-up augmented screw osteosynthesis was significantly superior to the conventional fixed-angle locking plate osteosynthesis with respect to primary stability and ROM during cyclic testing.

Vapor-induced phase-separation-enabled versatile direct ink writing.

Versatile printing of polymers, metals, and composites always calls for simple, economic approaches. Here we present an approach to three-dimensional (3D) printing of polymeric, metallic, and composite materials at room conditions, based on the polymeric vapor-induced phase separation (VIPS) process. During VIPS 3D printing (VIPS-3DP), a dissolved polymer-based ink is deposited in an environment where nebulized non-solvent is present, inducing the low-volatility solvent to be extracted from the filament in a controllable manner due to its higher chemical affinity with the non-solvent used. The polymeric phase is hardened in situ as a result of the induced phase separation process. The low volatility of the solvent enables its reclamation after the printing process, significantly reducing its environmental footprint. We first demonstrate the use of VIPS-3DP for polymer printing, showcasing its potential in printing intricate structures. We further extend VIPS-3DP to the deposition of polymer-based metallic inks or composite powder-laden polymeric inks, which become metallic parts or composites after a thermal cycle is applied. Furthermore, spatially tunable porous structures and functionally graded parts are printed by using the printing path to set the inter-filament porosity as well as an inorganic space-holder as an intra-filament porogen.

Renal resistance index and its prognostic significance in patients with heart failure with preserved ejection fraction.

BACKGROUND: Functional renal impairment is a common feature of heart failure with preserved ejection fraction (HFpEF). The link between functional renal impairment and HFpEF remains incompletely understood. With hypertension and diabetes as frequent co-morbidities, patients with HFpEF are at risk of developing intra-renal vascular hemodynamic alterations that may lead to functional renal impairment and impact on prognosis. METHODS: Renal resistive index (RRI) was non-invasively determined by Doppler ultrasonic examination in 90 HFpEF patients and 90 age- and sex-matched hypertensive patients without evidence of heart failure (HF) who served as controls. Clinical, laboratory and cardiac echocardiography data were obtained in HFpEF patients and controls. To investigate its possible clinical relevance, RRI was evaluated as a prognostic index of all-cause mortality and hospitalization for HF. RESULTS: Mean RRI was substantially greater in HFpEF patients than in controls (P < 0.0001), while mean blood pressure, glomerular filtration rate, hemoglobin and serum protein levels were significantly lower in HFpEF patients than in controls. On multivariable analysis, mean RRI was independently associated with HFpEF. In addition, increased mean RRI was an independent predictor of poor outcome [hazard ratio = 1.06 95% confidence interval (1.01-1.10), P = 0.007] and remained significantly associated with the outcome after adjustment for univariate predictors that included low mean blood pressure, low hemoglobin concentration and low glomerular filtration rate. Conclusion. Patients with HFpEF exhibit intra-renal vascular hemodynamic alterations. The severity of intra-renal vascular hemodynamic alterations correlates with a poor outcome.

Bioprinting on Live Tissue for Investigating Cancer Cell Dynamics.

A challenge in cancer research is the lack of physiologically responsive in vitro models that enable tracking of cancer cells in tissue-like environments. A model that enables real-time investigation of cancer cell migration, fate, and function during angiogenesis does not exist. Current models, such as 2D or 3D in vitro culturing, can contain multiple cell types, but they do not incorporate the complexity of intact microvascular networks. The objective of this study was to establish a tumor microvasculature model by demonstrating the feasibility of bioprinting cancer cells onto excised mouse tissue. Inkjet-printed DiI+ breast cancer cells on mesometrium tissues from C57Bl/6 mice demonstrated cancer cells' motility and proliferation through time-lapse imaging. Colocalization of DAPI+ nuclei confirmed that DiI+ cancer cells remained intact postprinting. Printed DiI+ 4T1 cells also remained viable after printing on Day 0 and after culture on Day 5. Time-lapse imaging over 5 days enabled tracking of cell migration and proliferation. The number of cells and cell area were significantly increased over time. After culture, cancer cell clusters were colocalized with angiogenic microvessels. The number of vascular islands, defined as disconnected endothelial cell segments, was increased for tissues with bioprinted cancer cells, which suggests that the early stages of angiogenesis were influenced by the presence of cancer cells. Bioprinting cathepsin L knockdown 4T1 cancer cells on wild-type tissues or nontarget 4T1 cells on NG2 knockout tissues served to validate the use of the model for probing tumor cell versus microenvironment changes. These results establish the potential for bioprinting cancer cells onto live mouse tissues to investigate cancer microvascular dynamics within a physiologically relevant microenvironment. Impact statement To keep advancing the cancer biology field, tissue engineering has been focusing on developing in vitro tumor biomimetic models that more closely resemble the native microenvironment. We introduce a novel methodology of bioprinting exogenous cancer cells onto mouse tissue that contains multiple cells and systems within native physiology to investigate cancer cell migration and interactions with nearby microvascular networks. This study corroborates the manipulation of different exogenous cells and host microenvironments that impact cancer cell dynamics in a physiologically relevant tissue. Overall, it is a new approach for delineating the effects of the microenvironment on cancer cells and vice versa.

[Diagnosis and non-invasive evaluation of a patient with obliterating arteriopathy of the lower limbs]. / Diagnosis et evaluation non invasive dún patient ayant une artériopathie oblitérante des membres inférieurs.

Obliterating arteriopathy of the lower limbs (OALL) is a pathology that manifests itself late in the natural history of an atheromatous patient. It is largely a localised pathology but should be considered as a marker for more generalised disease, for which the prognosis is modified by cardiac and cerebrovascular complications. Measurement of the systolic blood pressure index at the ankles is indispensable for initial management, with measures inferior to 0.90 correlating with an arterial stenosis of more than 50%, even in the absence of symptoms. Although the diagnosis is above-all clinical, further investigations complete the initial management by estimating the severity of the lesions, identifying the threatening lesions, allowing an overview of the general disease and a follow-up of the patient. Undoubtedly, the Doppler ultrasound remains the first-line investigation of choice. Helical computerised tomography and angiography by magnetic resonance imaging complete the initial investigation when a revascularisation procedure is envisaged, their respective indications depending on the protocols of each Vascular Centre. The walking-on-a-rolling-carpet test allows evaluation of residual functional capacity of the patient at the stage of claudication. The discovery of OALL calls for at least coronary screening, whatever be the stage of severity, with one patient in four dying of a coronary complication in 5 years. Other vascular localisations should be screened for depending on the clinical symptomatology. The medico-economic value of an extensive systematic vascular work-up is, in effect, still only demonstrated for the stage of claudication.

Tangential View and Intraoperative Three-Dimensional Fluoroscopy for the Detection of Screw-Misplacements in Volar Plating of Distal Radius Fractures.

BACKGROUND: Volar locking plate fixation has become the gold standard in the treatment of unstable distal radius fractures. Juxta-articular screws should be placed as close as possible to the subchondral zone, in an optimized length to buttress the articular surface and address the contralateral cortical bone. On the other hand, intra-articular screw misplacements will promote osteoarthritis, while the penetration of the contralateral bone surface may result in tendon irritations and ruptures. The intraoperative control of fracture reduction and implant positioning is limited in the common postero-anterior and true lateral two-dimensional (2D)-fluoroscopic views. Therefore, additional 2D-fluoroscopic views in different projections and intraoperative three-dimensional (3D) fluoroscopy were recently reported. Nevertheless, their utility has issued controversies. OBJECTIVES: The following questions should be answered in this study; 1) Are the additional tangential view and the intraoperative 3D fluoroscopy useful in the clinical routine to detect persistent fracture dislocations and screw misplacements, to prevent revision surgery? 2) Which is the most dangerous plate hole for screw misplacement? PATIENTS AND METHODS: A total of 48 patients (36 females and 13 males) with 49 unstable distal radius fractures (22 x 23 A; 2 x 23 B, and 25 x 23 C) were treated with a 2.4 mm variable angle LCP Two-Column volar distal radius plate (Synthes GmbH, Oberdorf, Switzerland) during a 10-month period. After final fixation, according to the manufactures' technique guide and control of implant placement in the two common perpendicular 2D-fluoroscopic images (postero-anterior and true lateral), an additional tangential view and intraoperative 3D fluoroscopic scan were performed to control the anatomic fracture reduction and screw placements. Intraoperative revision rates due to screw misplacements (intra-articular or overlength) were evaluated. Additionally, the number of surgeons, time and radiation-exposure, for each step of the operating procedure, were recorded. RESULTS: In the standard 2D-fluoroscopic views (postero-anterior and true lateral projection), 22 screw misplacements of 232 inserted screws were not detected. Based on the additional tangential view, 12 screws were exchanged, followed by further 10 screws after performing the 3D fluoroscopic scan. The most lateral screw position had the highest risk for screw misplacement (accounting for 45.5% of all exchanged screws). The mean number of images for the tangential view was 3 ± 2.5 images. The mean surgical time was extended by 10.02 ± 3.82 minutes for the 3D fluoroscopic scan. An additional radiation exposure of 4.4 ± 4.5seconds, with a dose area product of 39.2 ± 14.5 cGy/cm(2) were necessary for the tangential view and 54.4 ± 20.9 seconds with a dose area product of 2.1 ± 2.2 cGy/cm(2), for the 3D fluoroscopic scan. CONCLUSIONS: We recommend the additional 2D-fluoroscopic tangential view for detection of screw misplacements caused by overlength, with penetration on the dorsal cortical surface of the distal radius, predominantly observed for the most lateral screw position. The use of intraoperative 3D fluoroscopy did not become accepted in our clinical routine, due to the technical demanding and time consuming procedure, with a limited image quality so far.