Making Nanofiber Membrane Stand on End to Construct Vertically Interfacial Evaporators for Efficient Solar Evaporation, Omnidirectional Solar Absorption, and Ultrahigh-Salinity Brine Desalination.

Solar-driven interfacial desalination is widely considered to be a promising technology to address the global water crisis. This study proposes a novel electrospun nanofiber-based all-in-one vertically interfacial solar evaporator endowed with a high steam generation rate, steady omnidirectional evaporation, and enduring ultrahigh-salinity brine desalination. In particular, the electrospun nanofiber is collected into the tubular structure, followed by spraying with a dense crosslinked poly(vinyl alcohol) film, which renders them sufficiently strong for the preparation of a vertically array evaporator. The integrated evaporator made an individual capillary as a unit to form multiple thermal localization interfaces and steam dissipation channels, realizing zone heating of water. Thus a high steam generation rate exceeding 4.0 kg m-2 h-1 in pure water is demonstrated even under omnidirectional sunlight, and outperforms existing evaporators. Moreover, salt ions in the photothermal layer can be effectively transported to the water in capillaries and subsequently exchanged with the bulk water due to the strong action of capillary force, which ensures an ultrahigh desalination rate (≈12.5 kg m-2 h-1 under 3 sun) in 25 wt% concentration brine over 300 min. As such, this work provides a meaningful roadmap for the development of state-of-the-art solar-driven interfacial desalination.

Stable and Salt-Resistant Janus Evaporator Based on Cellulose Composite Aerogels from Waste Cotton Fabric.

Solar steam generation has been considered a promising approach for using renewable solar energy to produce clean water from seawater and wastewater. It shows great potential for alleviating water shortages. However, salt accumulation and system longevity are challenges which impede the widespread use of evaporators. This paper reports a stable Janus evaporator with thickness controllable hydrophilic and hydrophobic layers based on cellulose composite aerogels, which were extracted from waste cotton fabric by a two-step freeze-drying process. The obtained glutaraldehyde cross-linked carbon nanotubes/cellulose Janus aerogel exhibited an attractive solar steam generation rate of 1.81 kg·m-2·h-1 and a light-to-vapor efficiency of up to 92.5% in 1 sun illumination. Moreover, the Janus solar steam generator could pledge stable and sustainable solar-driven water evaporation performance within a 10 h test, showing a high salt-resistant property in simulated seawater. In addition, the developed solar evaporator also had a good purification effect on dye wastewater. These findings suggest its potential ability for seawater desalination and wastewater purification.

Sustainable Cellulose Aerogel from Waste Cotton Fabric for High-Performance Solar Steam Generation.

The textile industry has been considered as one of the polluting industries, producing a large amount of textile waste and CO2 emissions each year. Recycling of waste fabric has attracted more research interest in recent years. Herein, renewable polydopamine (PDA)-functionalized cellulose aerogels (CAs) have been designed by a feasible and green way for clean water generation. With the polymerization of PDA on the surface, which possesses excellent photothermal conversion performance and water purification ability, the resulting CA could achieve a high light absorption of 96.5% with the evaporation rate of 2.74 kg m-2 h-1 under 1 sun. Meanwhile, the solar steam generator with the increasing height can absorb energy from adjacent ambient air to strengthen the vapor generation. The features of renewable CAs can achieve efficient water evaporation, which combined with their low material cost and recycling, offer promise in reducing not only energy consumption but also the environmental footprint of cotton textiles.

Stretchable Thermoelectric-Based Self-Powered Dual-Parameter Sensors with Decoupled Temperature and Strain Sensing.

Thermoelectric-based sensors with multifunctional sensing properties that can recognize different stimulations in a self-powered environment by converting low-grade heat into electrical energy have attracted increasing attention. However, the current thermoelectric-based multifunctional sensors are faced with issues such as limited preparation methods, complex structural designs, and hard decoupling, which greatly hinder their further development in the field of wearable electronics. Herein, we have fabricated novel free-standing self-powered temperature-strain sensors based on poly(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT:PSS)/carbon nanotube (CNT)/waterborne polyurethane (WPU) composite films through a simple drop-casting method. The composite films can maintain stable thermoelectric performance after washing 1000 times and withstand repeated bending and stretching. More importantly, based on the Seebeck effect arising from PEDOT:PSS/CNT composites, the assembled sensor successfully detects temperature changes and strain deformations under a self-powered condition. The decoupling of strain stimulation and temperature stimulation is mainly attributed to the good conductive network inside the composite film and the conductive bridge formed by PEDOT:PSS particles between CNTs when the composite film is stretched. Thus, the designed self-powered sensor with dual-parameter sensing prepared by a simple strategy has shown great potential in wearable electronics.

High-Performance Solar Steam Generator Based on Polypyrrole-Coated Fabric via 3D Macro- and Microstructure Design.

Due to the abundance and easy availability of solar energy resources, solar-driven water evaporation provides a sustainable way to obtain clean water from wastewater and seawater. However, achieving a high evaporation rate with excellent light absorption remains a critical challenge in the structural regulation of evaporators. Herein, inspired by the natural transpiration process in plants (blue spruce), we designed a three-dimensional (3D) cone-shaped solar steam generator based on vertical polypyrrole nanowires-coated fabric (VPPyNWs-fabric). The microstructure design of polypyrrole (PPy) increases the solar energy absorption of the incident light through multiple reflections between the VPPyNWs, while the macrostructure design of the 3D evaporator possesses an enlarged surface area for energy harvesting, wide path for water supply, and open structure for vapor diffusion. As a proof of concept, the as-obtained 3D VPPyNWs-fabric-based solar steam generator demonstrates a fast water evaporation rate of 2.32 kg m-2 h-1 with high solar absorption of 97% and solar-to-vapor conversion efficiency of 98.56% at 1 kW m-2 energy density. In addition, the solar steam generator can be steadily applied in various water conditions, e.g., seawater, dye wastewater, and acidic and alkaline wastewater. This high-performance evaporator via 3D macro- and microstructure design offers a new avenue for better utilization of solar energy.

Growing ZnO Nanoparticles on Polydopamine-Templated Cotton Fabrics for Durable Antimicrobial Activity and UV Protection.

This work aims to develop durable functional cotton fabrics by growing zinc oxide (ZnO) nanoparticles on polydopamine (PDA) templates. ZnO nanoparticles were grown on the PDA-templated cotton fabrics by the hydrothermal method at room temperature. The surface morphology, chemical composition, and crystalline structure of the ZnO-coated cotton fabrics were characterized by scanning electron microscope (SEM) with energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The ZnO nanoparticles were found to disperse evenly on the surface of cotton fabrics. The ultraviolet (UV) protection factor (UPF) value of the ZnO-coated cotton fabrics was maintained at 122.5, and 99% reduction in bacterial load was observed against Gluconobacter cerinus even after five cycles of laundering. The PDA was found to be effective in fixing the ZnO seeds tightly on the surface of cotton fabrics, resulting in excellent durability of the coating of ZnO nanoparticles.