Shape-controlled single-crystal growth of InP at low temperatures down to 220 °C.

III-V compound semiconductors are widely used for electronic and optoelectronic applications. However, interfacing III-Vs with other materials has been fundamentally limited by the high growth temperatures and lattice-match requirements of traditional deposition processes. Recently, we developed the templated liquid-phase (TLP) crystal growth method for enabling direct growth of shape-controlled single-crystal III-Vs on amorphous substrates. Although in theory, the lowest temperature for TLP growth is that of the melting point of the group III metal (e.g., 156.6 °C for indium), previous experiments required a minimum growth temperature of 500 °C, thus being incompatible with many application-specific substrates. Here, we demonstrate low-temperature TLP (LT-TLP) growth of single-crystalline InP patterns at substrate temperatures down to 220 °C by first activating the precursor, thus enabling the direct growth of InP even on low thermal budget substrates such as plastics and indium-tin-oxide (ITO)-coated glass. Importantly, the material exhibits high electron mobilities and good optoelectronic properties as demonstrated by the fabrication of high-performance transistors and light-emitting devices. Furthermore, this work may enable integration of III-Vs with silicon complementary metal-oxide-semiconductor (CMOS) processing for monolithic 3D integrated circuits and/or back-end electronics.

Wearable Sweat Band for Noninvasive Levodopa Monitoring.

Levodopa is the standard medication clinically prescribed to patients afflicted with Parkinson's disease. In particular, the monitoring and optimization of levodopa dosage are critical to mitigate the onset of undesired fluctuations in the patients' physical and emotional conditions such as speech function, motor behavior, and mood stability. The traditional approach to optimize levodopa dosage involves evaluating the subjects' motor function, which has many shortcomings due to its subjective and limited quantifiable nature. Here, we present a wearable sweat band on a nanodendritic platform that quantitatively monitors levodopa dynamics in the body. Both stationary iontophoretic induction and physical exercise are utilized as our methods of sweat extraction. The sweat band measures real-time pharmacokinetic profiles of levodopa to track the dynamic response of the drug metabolism. We demonstrated the sweat band's functionalities on multiple subjects with implications toward the systematic administering of levodopa and routine management of Parkinson's disease.

Chemical Bath Deposition of p-Type Transparent, Highly Conducting (CuS)x:(ZnS)1-x Nanocomposite Thin Films and Fabrication of Si Heterojunction Solar Cells.

P-type transparent conducting films of nanocrystalline (CuS)x:(ZnS)1-x were synthesized by facile and low-cost chemical bath deposition. Wide angle X-ray scattering (WAXS) and high resolution transmission electron microscopy (HRTEM) were used to evaluate the nanocomposite structure, which consists of sub-5 nm crystallites of sphalerite ZnS and covellite CuS. Film transparency can be controlled by tuning the size of the nanocrystallites, which is achieved by adjusting the concentration of the complexing agent during growth; optimal films have optical transmission above 70% in the visible range of the spectrum. The hole conductivity increases with the fraction of the covellite phase and can be as high as 1000 S cm(-1), which is higher than most reported p-type transparent materials and approaches that of n-type transparent materials such as indium tin oxide (ITO) and aluminum doped zinc oxide (AZO) synthesized at a similar temperature. Heterojunction p-(CuS)x:(ZnS)1-x/n-Si solar cells were fabricated with the nanocomposite film serving as a hole-selective contact. Under 1 sun illumination, an open circuit voltage of 535 mV was observed. This value compares favorably to other emerging heterojunction Si solar cells which use a low temperature process to fabricate the contact, such as single-walled carbon nanotube/Si (370-530 mV) and graphene/Si (360-552 mV).

General Thermal Texturization Process of MoS2 for Efficient Electrocatalytic Hydrogen Evolution Reaction.

Molybdenum disulfide (MoS2) has been widely examined as a catalyst containing no precious metals for the hydrogen evolution reaction (HER); however, these examinations have utilized synthesized MoS2 because the pristine MoS2 mineral is known to be a poor catalyst. The fundamental challenge with pristine MoS2 is the inert HER activity of the predominant (0001) basal surface plane. In order to achieve high HER performance with pristine MoS2, it is essential to activate the basal plane. Here, we report a general thermal process in which the basal plane is texturized to increase the density of HER-active edge sites. This texturization is achieved through a simple thermal annealing procedure in a hydrogen environment, removing sulfur from the MoS2 surface to form edge sites. As a result, the process generates high HER catalytic performance in pristine MoS2 across various morphologies such as the bulk mineral, films composed of micron-scale flakes, and even films of a commercially available spray of nanoflake MoS2. The lowest overpotential (η) observed for these samples was η = 170 mV to obtain 10 mA/cm(2) of HER current density.

Artificial Photosynthesis on TiO2-Passivated InP Nanopillars.

Here, we report photocatalytic CO2 reduction with water to produce methanol using TiO2-passivated InP nanopillar photocathodes under 532 nm wavelength illumination. In addition to providing a stable photocatalytic surface, the TiO2-passivation layer provides substantial enhancement in the photoconversion efficiency through the introduction of O vacancies associated with the nonstoichiometric growth of TiO2 by atomic layer deposition. Plane wave-density functional theory (PW-DFT) calculations confirm the role of oxygen vacancies in the TiO2 surface, which serve as catalytically active sites in the CO2 reduction process. PW-DFT shows that CO2 binds stably to these oxygen vacancies and CO2 gains an electron (-0.897e) spontaneously from the TiO2 support. This calculation indicates that the O vacancies provide active sites for CO2 absorption, and no overpotential is required to form the CO2(-) intermediate. The TiO2 film increases the Faraday efficiency of methanol production by 5.7× to 4.79% under an applied potential of -0.6 V vs NHE, which is 1.3 V below the E(o)(CO2/CO2(-)) = -1.9 eV standard redox potential. Copper nanoparticles deposited on the TiO2 act as a cocatalyst and further improve the selectivity and yield of methanol production by up to 8-fold with a Faraday efficiency of 8.7%.

Enhanced Photocatalytic Reduction of CO2 to CO through TiO2 Passivation of InP in Ionic Liquids.

A robust and reliable method for improving the photocatalytic performance of InP, which is one of the best known materials for solar photoconversion (i.e., solar cells). In this article, we report substantial improvements (up to 18×) in the photocatalytic yields for CO2 reduction to CO through the surface passivation of InP with TiO2 deposited by atomic layer deposition (ALD). Here, the main mechanisms of enhancement are the introduction of catalytically active sites and the formation of a pn-junction. Photoelectrochemical reactions were carried out in a nonaqueous solution consisting of ionic liquid, 1-ethyl-3-methylimidazolium tetrafluoroborate ([EMIM]BF4), dissolved in acetonitrile, which enables CO2 reduction with a Faradaic efficiency of 99% at an underpotential of +0.78 V. While the photocatalytic yield increases with the addition of the TiO2 layer, a corresponding drop in the photoluminescence intensity indicates the presence of catalytically active sites, which cause an increase in the electron-hole pair recombination rate. NMR spectra show that the [EMIM](+) ions in solution form an intermediate complex with CO2(-), thus lowering the energy barrier of this reaction.

Efficient and sustained photoelectrochemical water oxidation by cobalt oxide/silicon photoanodes with nanotextured interfaces.

Plasma-enhanced atomic layer deposition of cobalt oxide onto nanotextured p(+)n-Si devices enables efficient photoelectrochemical water oxidation and effective protection of Si from corrosion at high pH (pH 13.6). A photocurrent density of 17 mA/cm(2) at 1.23 V vs RHE, saturation current density of 30 mA/cm(2), and photovoltage greater than 600 mV were achieved under simulated solar illumination. Sustained photoelectrochemical water oxidation was observed with no detectable degradation after 24 h. Enhanced performance of the nanotextured structure, compared to planar Si, is attributed to a reduced silicon oxide thickness that provides more intimate interfacial contact between the light absorber and catalyst. This work highlights a general approach to improve the performance and stability of Si photoelectrodes by engineering the catalyst/semiconductor interface.

BiVO4 thin film photoanodes grown by chemical vapor deposition.

BiVO4 thin film photoanodes were grown by vapor transport chemical deposition on FTO/glass substrates. By controlling the flow rate, the temperatures of the Bi and V sources (Bi metal and V2O5 powder, respectively), and the temperature of the deposition zone in a two-zone furnace, single-phase monoclinic BiVO4 thin films can be obtained. The CVD-grown films produce global AM1.5 photocurrent densities up to 1 mA cm(-2) in aqueous conditions in the presence of a sacrificial reagent. Front illuminated photocatalytic performance can be improved by inserting either a SnO2 hole blocking layer and/or a thin, extrinsically Mo doped BiVO4 layer between the FTO and the CVD-grown layer. The incident photon to current efficiency (IPCE), measured under front illumination, for BiVO4 grown directly on FTO/glass is about 10% for wavelengths below 450 nm at a bias of +0.6 V vs. Ag/AgCl. For BiVO4 grown on a 40 nm SnO2/20 nm Mo-doped BiVO4 back contact, the IPCE is increased to over 40% at wavelengths below 420 nm.

Amorphous Si thin film based photocathodes with high photovoltage for efficient hydrogen production.

An amorphous Si thin film with TiO2 encapsulation layer is demonstrated as a highly promising and stable photocathode for solar hydrogen production. With platinum as prototypical cocatalyst, a photocurrent onset potential of 0.93 V vs RHE and saturation photocurrent of 11.6 mA/cm(2) are measured. Importantly, the a-Si photocathodes exhibit impressive photocurrent of ~6.1 mA/cm(2) at a large positive bias of 0.8 V vs RHE, which is the highest for all reported photocathodes at such positive potential. Ni-Mo alloy is demonstrated as an alternative low-cost catalyst with onset potential and saturation current similar to those obtained with platinum. This low-cost photocathode with high photovoltage and current is a highly promising photocathode for solar hydrogen production.

Evaporated tellurium thin films for p-type field-effect transistors and circuits.

There is an emerging need for semiconductors that can be processed at near ambient temperature with high mobility and device performance. Although multiple n-type options have been identified, the development of their p-type counterparts remains limited. Here, we report the realization of tellurium thin films through thermal evaporation at cryogenic temperatures for fabrication of high-performance wafer-scale p-type field-effect transistors. We achieve an effective hole mobility of ~35 cm2 V-1 s-1, on/off current ratio of ~104 and subthreshold swing of 108 mV dec-1 on an 8-nm-thick film. High-performance tellurium p-type field-effect transistors are fabricated on a wide range of substrates including glass and plastic, further demonstrating the broad applicability of this material. Significantly, three-dimensional circuits are demonstrated by integrating multi-layered transistors on a single chip using sequential lithography, deposition and lift-off processes. Finally, various functional logic gates and circuits are demonstrated.

Evaporated Sex Te1- x Thin Films with Tunable Bandgaps for Short-Wave Infrared Photodetectors.

Semiconducting absorbers in high-performance short-wave infrared (SWIR) photodetectors and imaging sensor arrays are dominated by single-crystalline germanium and III-V semiconductors. However, these materials require complex growth and device fabrication procedures. Here, thermally evaporated Sex Te1- x alloy thin films with tunable bandgaps for the fabrication of high-performance SWIR photodetectors are reported. From absorption measurements, it is shown that the bandgaps of Sex Te1- x films can be tuned continuously from 0.31 eV (Te) to 1.87 eV (Se). Owing to their tunable bandgaps, the peak responsivity position and photoresponse edge of Sex Te1- x film-based photoconductors can be tuned in the SWIR regime. By using an optical cavity substrate consisting of Au/Al2 O3 to enhance its absorption near the bandgap edge, the Se0.32 Te0.68 film (an optical bandgap of ≈0.8 eV)-based photoconductor exhibits a cut-off wavelength at ≈1.7 µm and gives a responsivity of 1.5 AW-1 and implied detectivity of 6.5 × 1010 cm Hz1/2 W-1 at 1.55 µm at room temperature. Importantly, the nature of the thermal evaporation process enables the fabrication of Se0.32 Te0.68 -based 42 × 42 focal plane arrays with good pixel uniformity, demonstrating the potential of this unique material system used for infrared imaging sensor systems.

Integration of amorphous ferromagnetic oxides with multiferroic materials for room temperature magnetoelectric spintronics.

A room temperature amorphous ferromagnetic oxide semiconductor can substantially reduce the cost and complexity associated with utilizing crystalline materials for spintronic devices. We report a new material (Fe0.66Dy0.24Tb0.1)3O7-x (FDTO), which shows semiconducting behavior with reasonable electrical conductivity (~500 mOhm-cm), an optical band-gap (2.4 eV), and a large enough magnetic moment (~200 emu/cc), all of which can be tuned by varying the oxygen content during deposition. Magnetoelectric devices were made by integrating ultrathin FDTO with multiferroic BiFeO3. A strong enhancement in the magnetic coercive field of FDTO grown on BiFeO3 validated a large exchange coupling between them. Additionally, FDTO served as an excellent top electrode for ferroelectric switching in BiFeO3 with no sign of degradation after ~1010 switching cycles. RT magneto-electric coupling was demonstrated by modulating the resistance states of spin-valve structures using electric fields.

Roll-to-Roll Gravure Printed Electrochemical Sensors for Wearable and Medical Devices.

As recent developments in noninvasive biosensors spearhead the thrust toward personalized health and fitness monitoring, there is a need for high throughput, cost-effective fabrication of flexible sensing components. Toward this goal, we present roll-to-roll (R2R) gravure printed electrodes that are robust under a range of electrochemical sensing applications. We use inks and electrode morphologies designed for electrochemical and mechanical stability, achieving devices with uniform redox kinetics printed on 150 m flexible substrate rolls. We show that these electrodes can be functionalized into consistently high performing sensors for detecting ions, metabolites, heavy metals, and other small molecules in noninvasively accessed biofluids, including sensors for real-time, in situ perspiration monitoring during exercise. This development of robust and versatile R2R gravure printed electrodes represents a key translational step in enabling large-scale, low-cost fabrication of disposable wearable sensors for personalized health monitoring applications.

Nanoscale Junction Formation by Gas-Phase Monolayer Doping.

A major challenge in transistor technology scaling is the formation of controlled ultrashallow junctions with nanometer-scale thickness and high spatial uniformity. Monolayer doping (MLD) is an efficient method to form such nanoscale junctions, where the self-limiting nature of semiconductor surfaces is utilized to form adsorbed monolayers of dopant-containing molecules followed by rapid thermal annealing (RTA) to diffuse the dopants to a desired depth. Unlike ion implantation, the process does not induce crystal damage, thus making it highly attractive for nanoscale transistor processing. To date, reported MLD processes have relied on solution processing for monolayer formation. Gas-phase processing, however, benefits from higher intra- and interwafer uniformity and conformal coverage of 3D structures and is more desirable for manufacturing. In this regard, we report a new approach for MLD in silicon and germanium using gas-phase monolayer formation. We call this technology gas-phase monolayer doping (GP-MLD). This method relies on sequential pulse-purge cycles of gas-phase dopant-containing molecules to form a boron- or phosphorus-containing monolayer on a target semiconductor surface. Here, we show the feasibility of our approach through the formation of ultrashallow B- and P-doped junctions on Si and Ge surfaces. The mechanism of adsorption is characterized using Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Sub-5 nm junction depths with high dopant dose are obtained as characterized by secondary ion mass spectrometry and sheet resistance measurements. Additionally, we demonstrate that area selectivity can be achieved via lithographic patterning of the monolayer dopants before the diffusion step. The results demonstrate the versatility of the GP-MLD approach for formation of controlled and ultrashallow junctions.

Microchannel contacting of crystalline silicon solar cells.

There is tremendous interest in reducing losses caused by the metal contacts in silicon photovoltaics, particularly the optical and resistive losses of the front metal grid. One commonly sought-after goal is the creation of high aspect-ratio metal fingers which provide an optically narrow and low resistance pathway to the external circuit. Currently, the most widely used metal contact deposition techniques are limited to widths and aspect-ratios of ~40 µm and ~0.5, respectively. In this study, we introduce the use of a micropatterned polydimethylsiloxane encapsulation layer to form narrow (~20 µm) microchannels, with aspect-ratios up to 8, on the surface of solar cells. We demonstrate that low temperature metal pastes, electroless plating and atomic layer deposition can all be used within the microchannels. Further, we fabricate proof-of-concept structures including simple planar silicon heterojunction and homojunction solar cells. While preliminary in both design and efficiency, these results demonstrate the potential of this approach and its compatibility with current solar cell architectures.

Room temperature multiplexed gas sensing using chemical-sensitive 3.5-nm-thin silicon transistors.

There is great interest in developing a low-power gas sensing technology that can sensitively and selectively quantify the chemical composition of a target atmosphere. Nanomaterials have emerged as extremely promising candidates for this technology due to their inherent low-dimensional nature and high surface-to-volume ratio. Among these, nanoscale silicon is of great interest because pristine silicon is largely inert on its own in the context of gas sensing, unless functionalized with an appropriate gas-sensitive material. We report a chemical-sensitive field-effect transistor (CS-FET) platform based on 3.5-nm-thin silicon channel transistors. Using industry-compatible processing techniques, the conventional electrically active gate stack is replaced by an ultrathin chemical-sensitive layer that is electrically nonconducting and coupled to the 3.5-nm-thin silicon channel. We demonstrate a low-power, sensitive, and selective multiplexed gas sensing technology using this platform by detecting H2S, H2, and NO2 at room temperature for environment, health, and safety in the oil and gas industry, offering significant advantages over existing technology. Moreover, the system described here can be readily integrated with mobile electronics for distributed sensor networks in environmental pollution mapping and personal air-quality monitors.

Gold-Mediated Exfoliation of Ultralarge Optoelectronically-Perfect Monolayers.

Gold-mediated exfoliation of ultralarge optoelectronically perfect monolayers with lateral dimensions up to ≈500 µm is reported. Electrical, optical, and X-ray photo-electron spectroscopy characterization show that the quality of the gold-exfoliated flakes is similar to that of tape-exfoliated flakes. Large-area flakes allow manufacturing of large-area mono-layer transition metal dichalcogenide electronics.

Magnesium Fluoride Electron-Selective Contacts for Crystalline Silicon Solar Cells.

In this study, we present a novel application of thin magnesium fluoride films to form electron-selective contacts to n-type crystalline silicon (c-Si). This allows the demonstration of a 20.1%-efficient c-Si solar cell. The electron-selective contact is composed of deposited layers of amorphous silicon (∼6.5 nm), magnesium fluoride (∼1 nm), and aluminum (∼300 nm). X-ray photoelectron spectroscopy reveals a work function of 3.5 eV at the MgF2/Al interface, significantly lower than that of aluminum itself (∼4.2 eV), enabling an Ohmic contact between the aluminum electrode and n-type c-Si. The optimized contact structure exhibits a contact resistivity of ∼76 mΩ·cm(2), sufficiently low for a full-area contact to solar cells, together with a very low contact recombination current density of ∼10 fA/cm(2). We demonstrate that electrodes functionalized with thin magnesium fluoride films significantly improve the performance of silicon solar cells. The novel contacts can potentially be implemented also in organic optoelectronic devices, including photovoltaics, thin film transistors, or light emitting diodes.

Superacid Passivation of Crystalline Silicon Surfaces.

The reduction of parasitic recombination processes commonly occurring within the silicon crystal and at its surfaces is of primary importance in crystalline silicon devices, particularly in photovoltaics. Here we explore a simple, room temperature treatment, involving a nonaqueous solution of the superacid bis(trifluoromethane)sulfonimide, to temporarily deactivate recombination centers at the surface. We show that this treatment leads to a significant enhancement in optoelectronic properties of the silicon wafer, attaining a level of surface passivation in line with state-of-the-art dielectric passivation films. Finally, we demonstrate its advantage as a bulk lifetime and process cleanliness monitor, establishing its compatibility with large area photoluminescence imaging in the process.